Yamaha Audio BR15M, BR15, BR12, BR12M, BR10 User Manual

SPEAKER SYSTEM

Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones

取扱説明書

ENGLISH

DEUTSCH

FRANÇAIS

ESPAÑOL

BR10/BR12/BR15 BR12M/BR15M

ENGLISH

Thank you for choosing the YAMAHA speaker system. In order to take maximum advantage of the speaker's features and ensure maximum performance and longevity, please read this manual carefully before using the speaker system. Keep the manual in a safe place for future reference.

PRECAUTIONS

PLEASE READ CAREFULLY BEFORE PROCEEDING

* Please keep this manual in a safe place for future reference.

WARNING

Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, ﬁre or other hazards. These precautions include, but are not limited to, the following:

Do not open Water warning

• Do not open the device or attempt to disassemble the internal parts or modify them in any way. The device contains no user-serviceable parts. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualiﬁed Yamaha service personnel.

• Do not expose the device to rain, use it near water or in damp or wet conditions, or place containers on it containing liquids which might spill into any openings.

CAUTION

Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the device or other property. These precautions include, but are not limited to, the following:

Location

• If you use a stand, make sure to observe the following precautions in order to avoid toppling the device or causing damage to the internal components.

- Check the stand’s speciﬁcations and make sure that it is sturdy enough to

support the weight of the speaker.

- Mount only one speaker on each speaker stand.

- Use the supplied screws if included.

-Tighten fastening screws securely.

- Use the speaker stands with their legs fully opened.

- Use the stand at a height of less than 140cm (55").

- Add weight such as sand bags around the stand legs to prevent them from

falling over.

- Remove the speakers from the stands before moving the stands or adjusting

their height.

- Limit the number of people around the placed stand.

We recommend using the TS-80 and TS-90 speaker stands manufactured by Ultimate Systems (sold separately) to support the speakers.

• When transporting or moving the device, always use two or more people. Attempting to lift the device by yourself may damage your back, result in other injury, or cause damage to the device itself.

• Before moving the device, remove all connected cables.

• Do not use the speaker’s handles for suspended installation. Doing so can result in damage or injury.

• Do not expose the device to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disﬁguration or damage to the internal components.

• Do not place the device in an unstable position where it might accidentally fall over.

(6)-1

Connections

• Before connecting the device to other devices, turn off the power for all devices. Before turning the power on or off for all devices, set all volume levels to minimum.

• Use only speaker cables for connecting speakers to the speaker jacks. Use of other types of cables may result in ﬁre.

• Be sure to observe the ampliﬁer’s rated load impedance (see page 4), particularly when connecting speakers in parallel. Connecting an impedance load outside the ampliﬁer's rated range can damage the ampliﬁer.

Handling caution

• When choosing a power ampliﬁer to use with your speakers, make sure that its power output matches the speakers’ power capacity (refer to the Speciﬁcations on page 18). Even if the ampliﬁer’s power output is lower than the speakers’ PGM (program) power capacity, the speakers may be damaged when clipping of a high input signal occurs. The following may cause damage to speakers

- Feedback caused when using a microphone.

- Continuous high sound pressure level produced by electronic instruments.

- Continuous high-power output of distorted signals.

- Popping noises caused by turning on equipment, or by connecting or

disconnecting system components while the ampliﬁer is turned on.

• When turning on the AC power in your audio system, always turn on the power ampliﬁer LAST, to avoid speaker damage. When turning the power off, the power ampliﬁer should be turned off FIRST for the same reason.

• Do not operate this device at high volume levels or at a level that is uncomfortable, since it is capable of producing sound levels that could cause permanent hearing loss. If you experience any discomfort or ringing in the ears, or suspect an hearing loss, you should consult an audiologist.

ENGLISH

Special Notice

Protective Circuit (poly switch)

All full-range loudspeakers are ﬁtted with a self-resetting poly switch that protects the high-frequency driver from damage caused by excessive power. If a loudspeaker cabinet loses high-frequency output, immediately remove power from the unit and wait for two to three minutes. This should be long enough to allow the poly switch to reset. Reapply power and check the performance of the high-frequency driver before continuing, with the power reduced to a level that does not cause the poly switch to interrupt the signal.

• Illustrations in this manual are for explanatory purposes only, and may not match the actual appearance of the product during operation.

• Company names and product names used in this Owner’s Manual are trademarks or registered trademarks of their respective owners.

Yamaha cannot be held responsible for damage caused by improper use or modiﬁcations to the device.

(6)-1

+ 5 hidden pages