YAMAHA YFM7RZ User Manual

READ THIS MANUAL CAREFULLY!

It contains important safety information.

OWNER’S MANUAL

YFM7RZ

YFM7RSEZ

WARNING

This ATV should not be ridden by anyone under 16 years of age.

1AS-28199-10LIT-11626-23-09

EBU17092

Read this manual carefully before operating this vehicle. This manual should stay with this ve-

hicle if it is sold.

EBU17170

INTRODUCTION

EBU17302

Congratulations on your purchase of the Yamaha YFM7RZ/YFM7RSEZ. This ATV represents the result of
many years of Yamaha experience in the production of fine sporting, touring, and pacesetting racing ma­chines. With the purchase of this Yamaha, you can now appreciate the high degree of craftsmanship and
reliability that have made Yamaha a leader in these fields.
This manual will provide you with a good basic understanding of the features and operation of this ATV.

This manual includes important safety information. It provides information about special tech­niques and skills necessary to ride the ATV. It also includes basic maintenance and inspection proce-

dures. If you have any questions regarding the operation or maintenance of your ATV, please consult a
Yamaha dealer.

AN IMPORTANT SAFETY MESSAGE:

● Read this manual together with TIPS FOR THE ATV RIDER carefully and completely before operating

your ATV. Make sure you understand all instructions.

● Pay close attention to the warning and notice labels on the ATV.

● Never operate an ATV without proper training or instruction. Free training is available to anyone who buys

a new ATV. Call 1-800-887-2887 for more information.

● This ATV should not be ridden by anyone under 16 years of age.

● This ATV is a high-performance ATV for off-road use only, for sport-type recreational and competitive use

by experienced operators.

EBU17330

IMPORTANT MANUAL INFORMATION

EBU17342

FAILURE TO FOLLOW THE WARNINGS CONTAINED IN THIS MANUAL CAN RESULT IN SERIOUS IN­JURY OR DEATH.
Particularly important information is distinguished in this manual by the following notations:

This is the safety alert symbol. It is used to alert you to potential per­sonal injury hazards. Obey all safety messages that follow this sym­bol to avoid possible injury or death.

WARNING

NOTICE

TIP

A WARNING indicates a hazardous situation which, if not avoided,
could result in death or serious injury.

A NOTICE indicates special precautions that must be taken to avoid
damage to the vehicle or other property.

A TIP provides key information to make procedures easier or clearer.

* Product and specifications are subject to change without notice.

EBU17350

IMPORTANT NOTICE

EBU17362

This ATV is designed and manufactured for off-road use only. It is illegal and unsafe to operate this ATV on
any public street, road or highway.
This ATV complies with all applicable off-road noise level and spark arrester laws and regulations in effect
at the time of manufacture.
Please check your local riding laws and regulations before operating this ATV.

EBU17382

YFM7RZ/YFM7RSEZ

OWNER’S MANUAL

©2009 by Yamaha Motor Corporation, U.S.A.

1st edition, February 2009

All rights reserved.

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Corporation, U.S.A.

is expressly prohibited.

Printed in Japan.

P/N LIT-11626-23-09

EWB00011

WARNING

Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.

EBU17420

TABLE OF CONTENTS

LOCATION OF THE WARNING AND

SPECIFICATION LABELS ............................ 1-1

SAFETY INFORMATION .............................. 2-1

Speed limiter ...............................................4-7

Clutch lever .................................................4-7

Brake lever ..................................................4-8

Brake pedal .................................................4-8

Parking brake lever .....................................4-9

Shift pedal .................................................4-10

Reverse knob “REV” .................................4-10

Fuel tank cap ............................................4-11

Fuel ...........................................................4-11

Seat ..........................................................4-13

Adjusting the front shock absorber

assemblies ..............................................4-14

Adjusting the rear shock absorber

assembly .................................................4-19

DESCRIPTION .............................................. 3-1

Left view ...................................................... 3-1

Right view.................................................... 3-1

Controls and instruments ............................ 3-2

INSTRUMENT AND CONTROL

FUNCTIONS .................................................. 4-1

Main switch ................................................ 4-1

Indicator lights and warning lights .............. 4-2

Multi-function display .................................. 4-3

Handlebar switches .................................... 4-5

Throttle lever .............................................. 4-6

PRE-OPERATION CHECKS ..........................5-1

Fuel .............................................................5-3

Engine oil ....................................................5-3

Coolant .......................................................5-3

Front and rear brakes .................................5-3

Throttle lever ...............................................5-4

Drive chain ..................................................5-4

Tires ............................................................5-4

Chassis fasteners .......................................5-6

Instruments, lights and switches .................5-6

OPERATION .................................................. 6-1

Starting the engine ..................................... 6-1

Operating the reverse knob and driving in

reverse ..................................................... 6-2

Shifting ....................................................... 6-3

Engine break-in .......................................... 6-5

Parking ....................................................... 6-5

Parking on a slope ..................................... 6-6

Accessories and loading ............................ 6-7

RIDING YOUR ATV ...................................... 7-1

GETTING TO KNOW YOUR ATV............... 7-2

RIDE WITH CARE AND GOOD

JUDGMENT .............................................. 7-2

BE CAREFUL WHERE YOU RIDE............. 7-9

TURNING YOUR ATV .............................. 7-12

CLIMBING UPHILL ................................... 7-14

RIDING DOWNHILL.................................. 7-16

CROSSING A SLOPE............................... 7-18

CROSSING THROUGH SHALLOW

WATER ................................................... 7-19

RIDING OVER ROUGH TERRAIN ........... 7-20

SLIDING AND SKIDDING ......................... 7-21

WHAT TO DO IF... .................................... 7-22

WHAT TO DO... ........................................ 7-22

PERIODIC MAINTENANCE AND

ADJUSTMENT................................................8-1

Owner’s manual and tool kit .......................8-1

Periodic maintenance chart for the

emission control system ...........................8-3

General maintenance and lubrication

chart ..........................................................8-5

Removing and installing the panel ..............8-9

Checking the spark plug .............................8-9

Engine oil and oil filter element .................8-12

Coolant .....................................................8-17

Cleaning the air filter element ...................8-20

Cleaning the spark arrester ......................8-24

Adjusting the engine idling speed .............8-26

Adjusting the throttle cable free play .........8-27

Valve clearance ........................................8-27

Brakes .......................................................8-28

Checking the front and rear brake pads ...8-28

Checking the brake fluid level ...................8-29

Changing the brake fluid ...........................8-31

Checking the front brake lever free play ...8-31

Checking the brake pedal position ............8-32

Adjusting the parking brake free play .......8-32

Brake light switches ..................................8-33

Adjusting the clutch lever free play ...........8-34

Drive chain slack .......................................8-35

Lubricating the drive chain ........................8-37

Checking and lubricating the cables ........ 8-38

Checking and lubricating the brake and

clutch levers ........................................... 8-38

Checking the shift pedal ........................... 8-38

Checking and lubricating the brake

pedal ...................................................... 8-39

Checking the wheel hub bearings ............ 8-39

Lubricating the swingarm pivots ............... 8-39

Lubricating the rear suspension relay arm

and connecting arm pivoting points ........ 8-39

Lubricating the upper and lower arm

pivots ...................................................... 8-40

Battery ...................................................... 8-41

Replacing a fuse ...................................... 8-44

Replacing a headlight bulb ....................... 8-46

Adjusting a headlight beam ...................... 8-47

Tail/brake light .......................................... 8-48

Removing a wheel .................................... 8-48

Installing a wheel ...................................... 8-48

Troubleshooting ....................................... 8-49

Troubleshooting charts ............................. 8-50

CLEANING AND STORAGE.......................... 9-1

Cleaning ..................................................... 9-1

Storage ....................................................... 9-2

SPECIFICATIONS .......................................10-1

CONSUMER INFORMATION.......................11-1

Identification numbers ...............................11-1

Noise regulation ........................................11-4

Maintenance record ..................................11-5

YAMAHA MOTOR CORPORATION,

U.S.A. ATV LIMITED WARRANTY .........11-6

YAMAHA EXTENDED SERVICE

(Y.E.S.) ...................................................11-8

EBU17660

LOCATION OF THE WARNING AND SPECIFICATION LABELS

1

4

1
2

5

3

6

1-1

6

EBU17670

Read and understand all of the labels on your ATV. These labels contain important information for safe and

1

proper operation.
Never remove any labels from your ATV. If a label becomes difficult to read or comes off, request a replace­ment label from your Yamaha dealer.

1-2

13

This ATV complies with applicable provisions of
ANSI/SVIA 1-2007 and is subject to an approved
ATV action plan submitted by YAMAHA and is on file
with the U.S. Consumer Product safety Commission.

Certification of Compliance

YAMAHA MOTOR CORPORATION U.S.A.

6555 Katella Avenue, Cypress, California 90630-5101, U.S.A.

43P-2817J-00

2

1

1-3

45

1

WARNING

NEVER ride as a

passenger.

Passengers can cause

a loss of control,

resulting in SEVERE

Improper tire pressure or overloading can cause
loss of control.
Loss of control can result in severe injury of
death.
OPERATING TIRE PRESSURE : Set with tires cold

• Recommended : Front : 4.0 psi ( 27.5 kPa )

• Minimum : Front : 3.6 psi ( 24.5 kPa )

• Never set tire pressure below minimum.
It could cause the tire to dislodge from the rim.

ROADING

• Maximum weight capacity : 220 lbs ( 100 kg )
Includes walght of operator, cargo and accessories.

INJURY or DEATH.

5FE-2151H-01

WARNING

: Rear : 4.0 psi ( 27.5 kPa )

: Rear : 3.6 psi ( 24.5 kPa )

4D3-2816M-U0

6

WARNING

This unit contains high pressure nitrogen gas.
Mishandling can cause explosion.

• Read owner’s manual for instructions.

• Do not incinerate, puncture or open.

1-4

EBU17431

SAFETY INFORMATION

EBU26663

AN ATV IS NOT A TOY AND CAN BE HAZARD­OUS TO OPERATE.

An ATV handles differently from other vehicles, in­cluding motorcycles and cars. A collision or roll­over can occur quickly, even during routine
maneuvers such as turning and riding on hills or
over obstacles, if you fail to take proper precau­tions.
SEVERE INJURY OR DEATH can result if you do
not follow these instructions:

● Read this manual and all labels carefully and fol-

low the operating procedures described.

● Never operate an ATV without proper training or

instruction. Take a Training Course.

Beginners
should receive training from a certified instruc­tor. Contact an authorized ATV dealer or call 1­800-887-2887 to find out about the training
courses nearest you.

● Always follow the age recommendation:

2

– A child under 16 years old should never oper­ate an ATV with engine size greater than 90 cc.

● Never allow a child under age 16 to operate an

ATV without adult supervision, and never allow
continued use of an ATV by a child if he or she
does not have the abilities to operate it safely.

● Never carry a passenger on an ATV.

● Always avoid operating an ATV on any paved

surfaces, including sidewalks, driveways, park­ing lots and streets.

● Never operate an ATV on any public street, road

or highway, even a dirt or gravel one.

● Never operate an ATV without wearing an ap-

proved motorcycle helmet that fits properly. You
should also wear eye protection (goggles or face
shield), gloves, boots, a long-sleeved shirt or a
jacket, and long pants.

● Never consume alcohol or drugs before or while

operating this ATV.

2-1

● Never operate at speeds too fast for your skills

or the riding conditions. Always go at a speed
that is proper for the terrain, visibility, operating
conditions, and your experience.

2

● Never attempt wheelies, jumps, or other stunts.

● Always inspect your ATV each time you use it to

make sure it is in safe operating condition. Al­ways follow the inspection and maintenance
procedures and schedules described in this
manual.

● Always keep both hands on the handlebars and

both feet on the footboards of the ATV during
operation.

● Always go slowly and be extra careful when op-

erating on unfamiliar terrain. Always be alert to
changing terrain conditions when operating the
ATV.

● Never operate on excessively rough, slippery or

loose terrain until you have learned and prac­ticed the skills necessary to control the ATV on
such terrain. Always be especially cautious on
these kinds of terrain.

● Always follow proper procedures for turning as

described in this manual. Practice turning at low
speeds before attempting to turn at faster
speeds and never turn at excessive speeds.

● Never operate the ATV on hills too steep for the

ATV or for your abilities. Practice on smaller hills
before attempting larger hills.

● Always follow proper procedures for climbing

hills as described in this manual. Check the ter­rain carefully before you start up any hill. Never
climb hills with excessively slippery or loose sur­faces. Shift your weight forward. Never open the
throttle suddenly or make sudden gear changes.
Never go over the top of a hill at high speed.

● Always follow proper procedures for going down

hills and for braking on hills as described in this
manual. Check the terrain carefully before you
start down any hill. Shift your weight backward.
Never go down a hill at high speed. Avoid going
down a hill at an angle that would cause the ve­hicle to lean sharply to one side. Go straight
down the hill where possible.

● Always follow proper procedures for crossing

the side of a hill as described in this manual.
Avoid hills with excessively slippery or loose sur­faces. Shift your weight to the uphill side of the
ATV. Never attempt to turn the ATV around on
any hill until you have mastered the turning tech­nique described in this manual on level ground.
Avoid crossing the side of a steep hill if possible.

2-2

● Always use proper procedures if you stall or roll

backwards when climbing a hill. To avoid stall­ing, use the proper gear and maintain a steady
speed when climbing a hill. If you stall or roll
backwards, follow the special procedure for
braking described in this manual. Dismount on
the uphill side or to a side if pointed straight up­hill. Turn the ATV around and remount, following
the procedure described in this manual.

● Always check for obstacles before operating in a

new area.

● Never attempt to operate over large obstacles,

such as large rocks or fallen trees. Always follow
proper procedures when operating over obsta­cles as described in this manual.

● Always be careful when skidding or sliding.

Learn to safely control skidding or sliding by
practicing at low speeds and on level, smooth
terrain. On extremely slippery surfaces, such as
ice, go slowly and be very cautious in order to re­duce the chance of skidding or sliding out of con­trol.

● Never operate an ATV in fast flowing water or in

water deeper than that recommended in this
manual. Remember that wet brakes may have

reduced stopping ability. Test your brakes after
leaving water. If necessary, apply them several
times to let friction dry out the linings.

● Always be sure there are no obstacles or people

behind you when you operate in reverse. When
it is safe to proceed in reverse, go slowly.

● Always use the size and type of tires specified in

this manual.

● Always maintain proper tire pressure as de-

scribed in this manual.

● Never modify an ATV through improper installa-

tion or use of accessories.

● Never exceed the stated load capacity for an

ATV. Cargo should be properly distributed and
securely attached. Reduce speed and follow in­structions in this manual for carrying cargo or
pulling a trailer. Allow greater distance for brak­ing.

2

2-3

EWB00071

WARNING

Avoid Carbon Monoxide Poisoning
All engine exhaust contains carbon monoxide,

2

a deadly gas. Breathing carbon monoxide can
cause headaches, dizziness, drowsiness, nau­sea, confusion, and eventually death.
Carbon Monoxide is a colorless, odorless,
tasteless gas which may be present even if you
do not see or smell any engine exhaust. Deadly
levels of carbon monoxide can collect rapidly
and you can quickly be overcome and unable
to save yourself. Also, deadly levels of carbon
monoxide can linger for hours or days in en­closed or poorly ventilated areas. If you experi­ence any symptoms of carbon monoxide
poisoning, leave the area immediately, get
fresh air, and SEEK MEDICAL TREATMENT.

● Do not run engine indoors. Even if you try to

ventilate engine exhaust with fans or open
windows and doors, carbon monoxide can
rapidly reach dangerous levels.

● Do not run engine in poorly ventilated or par-

tially enclosed areas such as barns, garages,
or carports.

● Do not run engine outdoors where engine

exhaust can be drawn into a building
through openings such as windows and
doors.

FOR MORE INFORMATION ABOUT ATV SAFE­TY, call the Consumer Products Safety Commis-

sion at 1-800-638-2772, or the ATV Distributor’s
Safety Hotline at 1-800-852-5344.

2-4

EBU17680

DESCRIPTION

EBU17690

Left view

2

1

1. Engine oil tank

2. Coolant reservoir

3. Idle adjusting screw

4. Tail/brake light

5. Shift pedal

EBU17700

Right view

3

4

1

5

1. Spark arrester

2. Seat

3. Headlight

4. Brake pedal

2

4

3

3

3-1

EBU17712

Controls and instruments

2

1

3

1. Clutch lever

2. Parking brake lever

3. Main switch

4. Brake lever

5. Throttle lever

6. Reverse knob

7. Fuel tank cap

8. Handlebar switches

TIP

The ATV you have purchased may differ slightly

3

4

from the figures shown in this manual.

5678

3-2

EBU17725

INSTRUMENT AND CONTROL FUNCTIONS

EWB00011

WARNING

Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.

EBU17760

Main switch

The positions of the main switch are as follows:

ON

All electrical systems are supplied with power. The
headlights and taillight come on when the light
switch is on, and the engine can be started. The
key cannot be removed.

OFF

All electrical systems are off. The key can be re­moved.

OFF ON

1

4

1. Main switch

4-1

EBU26693

Indicator lights and warning lights

12

5

4

4

3

1. Neutral indicator light “N”

2. Reverse indicator light “R”

3. Coolant temperature warning light “”

4. Engine trouble warning light “”

5. Fuel level warning light “”

EBU17830

Reverse indicator light “”

This indicator light comes on when the transmis­sion is in the reverse position.

EBU17860

Neutral indicator light “”

This indicator light comes on when the transmis­sion is in the neutral position.

EBU26702

Coolant temperature warning light “”

This warning light comes on when the engine over­heats. When this occurs during operation, stop the
engine as soon as it is safe to do so and allow it to
cool down for about 10 minutes.
The electrical circuit of the warning light can be
checked by turning the key to “ON”. The warning
light should come on for a few seconds, and then
go off.
If the warning light does not come on initially when
the key is turned to “ON”, or if the warning light re­mains on, have a Yamaha dealer check the electri­cal circuit.

ECB00010

NOTICE

● The engine may overheat if the ATV is over-

loaded. In this case, reduce the load to spec­ification.

● Start the engine after making sure that the

warning light is out. Continuous use while
the warning light is on may cause damage to
the engine.

4-2

EBU29391

Fuel level warning light “”

This warning light comes on when the fuel level
drops below approximately 2.6 L (0.69 US gal,

0.57 Imp.gal). When this occurs, refuel as soon as
possible.
The electrical circuit of the warning light can be
checked by setting the engine stop switch to “”
and turning the key to “ON”. The warning light
should come on for a few seconds, and then go off.
If the warning light does not come on initially when
the key is turned to “ON”, or if the warning light re­mains on, have a Yamaha dealer check the electri­cal circuit.

EBU27283

Engine trouble warning light “”

This warning light comes on or flashes when an
electrical circuit monitoring the engine is not work­ing correctly. When this occurs, have a Yamaha
dealer check the self-diagnosis system. (See page
4-3 for an explanation of the self-diagnosis device.)
The electrical circuit of the warning light can be
checked by turning the key to “ON”. The warning
light should come on for a few seconds, and then
go off.

If the warning light does not come on initially when
the key is turned to “ON”, or if the warning light re­mains on, have a Yamaha dealer check the electri­cal circuit.

EBU29263

Multi-function display

4

34

2

1

5

1. “RESET” button

2. “SELECT” button

3. Speedometer

4. Clock/Hour meter

5. Odometer/Tripmeter A/Tripmeter B

The multi-function display is equipped with the fol­lowing:

● a speedometer

● an odometer

4-3

● two tripmeters (which show the distance trav-

eled since they were last set to zero)

● a clock

● an hour meter (which shows the total time the

engine has been running)

● a self-diagnosis device

Clock mode

Push and hold “SELECT” button for at least three
seconds to switch the display between the clock
mode “CLOCK” and the hour meter mode “HOUR”
in the following order:
CLOCK → HOUR → CLOCK

Odometer and tripmeter modes

4

Pushing the “SELECT” button switches the display
between the odometer mode “ODO” and the trip­meter modes “A” and “B” in the following order:
ODO → A → B → ODO
To reset a tripmeter, select it by pushing the “SE-
LECT” button, and then push the “RESET” button
for at least three seconds. The tripmeters can be
used to estimate the distance that can be traveled
with a full tank of fuel. This information will enable
you to plan future fuel stops.

TIP

Pushing and holding in the “SELECT” button, and
turning the key to “ON” while the button is pushed,
switches the display between “mph” and “km/h”.

To set the clock

1. Set the display to the clock mode.

2. Push the “SELECT” button and “RESET” but-
ton together for at least three seconds.

3. When the hour digits start flashing, push the
“RESET” button to set the hours.

4. Push the “SELECT” button, and the minute
digits will start flashing.

5. Push the “RESET” button to set the minutes.

6. Push the “SELECT” button and then release it
to start the clock.

4-4

Self-diagnosis device

EBU18061

Handlebar switches

1

4

1

1. Error code display

This model is equipped with a self-diagnosis de­vice for various electrical circuits.
If a problem is detected in any of those circuits, the
multi-function display will indicate an error code.
If the multi-function display indicates an error code,
note the code number, and then have a Yamaha
dealer check the vehicle.

ECB00811

NOTICE

If the multi-function display indicates an error
code, the vehicle should be checked as soon
as possible in order to avoid engine damage.

2

1. Light switch “ //OFF”

2. Engine stop switch “ / ”

3. Start switch “”

EBU18080

3

Engine stop switch “ / ”

Set this switch to “” before starting the engine.
The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to “”.

4-5

EBU18101

Start switch “”

Push this switch to crank the engine with the start­er. See the starting instructions on page 6-1 prior
to starting the engine.

EBU18152

Light switch “ //OFF”

Set this switch to “” to turn on the low beams

4

and the taillight. Set the switch to “” to turn on
the high beams and the taillight. Set the switch to
“OFF” to turn off all the lights.

ECB00041

NOTICE

Do not use the headlights with the engine
turned off for an extended period of time, oth­erwise the battery may discharge to the point
that the starter motor will not operate properly.
If this should happen, remove the battery and
recharge it. See page 8-41 for battery charging
information.

EBU18281

Throttle lever

Once the engine is running, movement of the throt­tle lever will increase the engine speed.

Regulate the speed of the ATV by varying the
throttle position. Because the throttle is spring­loaded, the ATV will decelerate, and the engine will
return to an idle any time the hand is removed from
the throttle lever.

1

1. Throttle lever

Before starting the engine, check the throttle to be
sure it is operating smoothly. Make sure it returns
to the idle position as soon as the lever is released.

4-6

EBU18322

Speed limiter

Your ATV was delivered with an adjustable speed
limiter. The speed limiter keeps the throttle from
fully opening, even when the throttle lever is
pushed to the maximum.

1. Loosen the locknut.

2. To increase the maximum engine power avail­able and the maximum speed of the ATV, turn
the adjusting screw in direction (a). To de­crease the maximum engine power available
and the maximum speed of the ATV, turn the
adjusting screw in direction (b). Do not turn
the adjusting screw out more than 12 mm
(0.47 in) or the throttle cable could be dam­aged. Always make sure the throttle lever free
play is adjusted to 2.0–4.0 mm (0.08–0.16 in).
(See page 8-27.) WARNING! Improper ad-

justment of the speed limiter and throttle
could cause throttle cable damage or im­proper throttle operation. You could lose
control, resulting in an accident.

[EWB00241]

3

12

(b)

(a)

1. Locknut

2. Adjusting screw

3. No more than 12 mm (0.47 in)

3. Tighten the locknut.

EBU18382

Clutch lever

The clutch lever is located on the left handlebar
and the ignition circuit cut-off system is incorporat­ed in the clutch lever holder. To disengage the
clutch, pull the clutch lever toward the handlebar
grip. To engage the clutch, release the clutch lever.
The clutch lever should be pulled rapidly and re-

4

4-7

leased slowly for smooth clutch operation. (See
page 6-1 for a description of the ignition circuit cut­off system.)

4

1. Clutch lever

EBU18421

Brake lever

The brake lever is located on the right handlebar.
To apply the front brake, pull the brake lever to­ward the handlebar grip.
The brake lever is equipped with a position adjust­ing bolt. To adjust the distance between the brake
lever and the handlebar grip, hold the brake lever
away from the handlebar so it does not contact the
adjusting bolt, loosen the locknut, turn the adjust­ing bolt, and then tighten the locknut.

1. Brake lever

2. Locknut

3. Brake lever position adjusting bolt

4. Distance between brake lever and handlebar grip

EBU18432

Brake pedal

The brake pedal is located on the right side of the
ATV. To apply the rear brake, push down on the
brake pedal.

4-8

1

1. Brake pedal

EBU18520

Parking brake lever

Use the parking brake before starting the engine or
parking the ATV, especially on a slope. To apply
the parking brake, move the parking brake lever in
direction (a). To release the parking brake, move
the parking brake lever in direction (b).

4

1. Parking brake lever (locked position)

1. Parking brake lever (unlocked position)

4-9

EWB00220

WARNING

● Always set the parking brake before starting

the engine. The ATV could start moving un­expectedly if the parking brake is not ap­plied. This could cause loss of control or a
collision.

● Always be sure you have released the park-

4

ing brake before you begin to ride. The brake
could overheat if you ride the ATV without re­leasing the parking brake. You could lose
braking performance which could cause an
accident. You could also wear out the brakes
prematurely.

EBU18540

Shift pedal

This ATV is equipped with a constant-mesh 5­speed forward and 1-speed reverse transmission.
The shift pedal is located on the left side of the en­gine and is used in combination with the clutch
when shifting.

1

1. Shift pedal

EBU18641

Reverse knob “REV”

The reverse knob is used to shift into reverse. See
the “Operating the reverse knob and driving in re­verse” section on page 6-2 before operating this
ATV in reverse.

4-10

1

1

4

1. Reverse knob “REV”

EBU18720

Fuel tank cap

Remove the fuel tank cap by turning it counter­clockwise.

1. Fuel tank cap

EBU18731

Fuel

Make sure there is sufficient gasoline in the tank.

EWB02521

WARNING

Gasoline and gasoline vapors are extremely
flammable. To avoid fires and explosions and
to reduce the risk of injury when refueling, fol­low these instructions.

1. Before refueling, turn off the engine and be
sure that no one is sitting on the vehicle. Nev­er refuel while smoking, or while in the vicinity

4-11

of sparks, open flames, or other sources of ig­nition such as the pilot lights of water heaters
and clothes dryers.

2. Do not overfill the fuel tank. When refueling,
be sure to insert the pump nozzle into the fuel
tank filler hole. Stop filling when the fuel reach­es the bottom of the filler tube. Because fuel

4

expands when it heats up, heat from the en­gine or the sun can cause fuel to spill out of
the fuel tank.

2

1

1. Filler tube

2. Fuel level

Recommended fuel:

UNLEADED GASOLINE ONLY

Fuel tank capacity:

11.0 L (2.91 US gal, 2.42 Imp.gal)

Fuel reserve amount:

2.6 L (0.69 US gal, 0.57 Imp.gal)

3. Wipe up any spilled fuel immediately.

NOTICE: Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since fuel may
deteriorate painted surfaces or plastic
parts.

[ECB00981]

4. Turn the fuel tank cap fully clockwise to make
sure it is securely closed.

EWB02531

WARNING

Gasoline is poisonous and can cause injury or
death. Handle gasoline with care. Never siphon
gasoline by mouth. If you should swallow
some gasoline or inhale a lot of gasoline vapor,
or get some gasoline in your eyes, see your
doctor immediately. If gasoline spills on your
skin, wash with soap and water. If gasoline
spills on your clothing, change your clothes.

4-12

ECB00070

NOTICE

Use only unleaded gasoline. The use of leaded
gasoline will cause severe damage to internal
engine parts, such as the valves and piston
rings, as well as to the exhaust system.

Your Yamaha engine has been designed to use
regular unleaded gasoline with a pump octane
number [(R+M)/2] of 86 or higher, or a research oc­tane number of 91 or higher. If knocking (or ping­ing) occurs, use a gasoline of a different brand.
Use of unleaded fuel will extend spark plug life and
reduce maintenance costs.

Gasohol

There are two types of gasohol: gasohol contain­ing ethanol and that containing methanol. Gasohol
containing ethanol can be used if the ethanol con­tent does not exceed 10% (E10). Gasohol contain­ing methanol is not recommended by Yamaha
because it can cause damage to the fuel system or
vehicle performance problems.

EBU18891

Seat

To remove the seat

Insert your hand between the rear of the seat and
the rear fender, pull the seat lock lever upward and
pull up the seat at the rear.

4

1

1. Seat lock lever

To install the seat

Insert the projections on the front of the seat into
the seat holders and push down on the seat at the
rear. Make sure that the seat is securely fitted.

4-13

4

1. Projection

2. Seat holder

EWB02601

1

WARNING

● Suspension components become hot during

operation. Never touch the compression
damping force adjusting screw, the rebound
damping force adjusting screw or the oil res­ervoir with your bare hand or skin until sus-

2

pension components have cooled.

● Always adjust the shock absorber assem-

blies on the left and right side to the same
setting. Uneven adjustment can cause poor
handling and loss of stability, which could
lead to an accident.

EBU27907

Adjusting the front shock absorber as­semblies

These shock absorber assemblies are equipped
with a spring preload adjusting nut, a rebound
damping force adjusting screw, with a compres­sion damping force adjusting bolt (for fast com­pression damping), and a compression damping
force adjusting screw (for slow compression damp­ing).

ECB00090

NOTICE

Never turn an adjusting mechanism beyond
the minimum and maximum settings.

Spring preload

1. Loosen the locknut.

2. Turn the spring preload adjusting nut in direc­tion (a) to increase the spring preload and
thereby harden the suspension, and in direc­tion (b) to decrease the spring preload and
thereby soften the suspension.

4-14

2

(a)

(b)

1. Spring preload adjusting nut

2. Locknut

3. Special wrench

TIP

● A special wrench can be obtained at a Yamaha

dealer to make this adjustment.

● The spring preload setting is determined by

measuring distance A, shown in the illustration.
The shorter distance A is, the higher the spring
preload; the longer distance A is, the lower the
spring preload. With each complete turn of the
adjusting nut, distance A is changed by 1.5 mm
(0.06 in).

1

3

Spring preload setting:

Minimum (soft):

Distance A = 263.0 mm (10.35 in)

Standard:

Distance A = 260.0 mm (10.24 in)

Maximum (hard):

Distance A = 251.0 mm (9.88 in)

1

1. Distance A

3. Tighten the locknut to the specified torque.

NOTICE: Always tighten the locknut
against the adjusting nut, and then tighten
it to the specified torque.

[ECB00081]

4

4-15

Tightening torque:

Locknut:

42 Nm (4.2 m·kgf, 30 ft·lbf)

Rebound damping force

Turn the rebound damping force adjusting screw in
direction (a) to increase the rebound damping
force and thereby harden the damping, and in di-

4

rection (b) to decrease the rebound damping force
and thereby soften the damping.

Rebound damping setting:

Minimum (soft):

20 click(s) in direction (b)*

Standard:

12 click(s) in direction (b)*

Maximum (hard):

3 click(s) in direction (b)*

* With the adjusting screw fully turned in direc-

tion (a)

TIP

Make sure that the position indicator marks are
aligned when the shock absorber assembly is set
to the standard setting.

(a)

1

(b)

1. Rebound damping force adjusting screw

2. Position indicator marks

Compression damping force

2

Compression damping force (for fast compression
damping)
To increase the compression damping force and
thereby harden the compression damping, turn the
compression damping force adjusting bolt in direc­tion (a). To decrease the compression damping
force and thereby soften the compression damp­ing, turn the adjusting bolt in direction (b).

4-16

(a)

TIP

Make sure that the position indicator marks are
aligned when the shock absorber assembly is set
to the standard setting.

1

(b)

1. Compression damping force adjusting bolt (for fast
compression damping)

2. Position indicator marks

Compression damping setting (for fast com­pression damping):

Minimum (soft):

4 turn(s) out from the fully turned in posi­tion

Standard:

2 turn(s) out from the fully turned in posi­tion

Maximum (hard):

Fully turned in

1

Compression damping force (for slow compres­sion damping)

2

To increase the compression damping force and

4

thereby harden the compression damping, turn the
compression damping force adjusting screw in di­rection (a). To decrease the compression damping
force and thereby soften the compression damp­ing, turn the adjusting screw in direction (b).

4-17

(a)

4

(b)

1. Compression damping force adjusting screw (for slow
compression damping)

Compression damping setting (for slow com­pression damping):

Minimum (soft):

16 click(s) in direction (b)*

Standard:

10 click(s) in direction (b)*

Maximum (hard):

1 click(s) in direction (b)*

* With the adjusting screw fully turned in direc-

tion (a)

1

TIP

Although the total number of clicks of a damping
force adjusting mechanism may not exactly match
the above specifications due to small differences in
production, the actual number of clicks always rep­resents the entire adjusting range. To obtain a pre­cise adjustment, it would be advisable to check the
number of clicks of each damping force adjusting
mechanism and to modify the specifications as
necessary.

EWB00410

WARNING

These shock absorber assemblies contain
highly pressurized nitrogen gas. Read and un­derstand the following information before han­dling the shock absorber assemblies.

● Do not tamper with or attempt to open the

cylinder assemblies.

● Do not subject the shock absorber assem-

blies to an open flame or other high heat
source. This may cause the unit to explode
due to excessive gas pressure.

● Do not deform or damage the cylinders in

any way. Cylinder damage will result in poor
damping performance.

4-18

● Do not dispose of a damaged or worn out

shock absorber assembly yourself. Take the
shock absorber assembly to a Yamaha deal­er for any service.

ECB00090

NOTICE

Never turn an adjusting mechanism beyond
the minimum and maximum settings.

EBU27963

Adjusting the rear shock absorber as­sembly

This shock absorber assembly is equipped with a
spring preload adjusting nut, a rebound damping
force adjusting screw, with a compression damp­ing force adjusting bolt (for fast compression
damping), and a compression damping force ad­justing screw (for slow compression damping).

EWB00440

WARNING

Suspension components become hot during
operation. Never touch the compression
damping force adjusting screw, the rebound
damping force adjusting screw or the oil reser­voir with your bare hand or skin until suspen­sion components have cooled.

Spring preload

1. Loosen the locknut.

2. Turn the spring preload adjusting nut in direc­tion (a) to increase the spring preload and
thereby harden the suspension, and in direc­tion (b) to decrease the spring preload and
thereby soften the suspension.

1

(b)

2

(a)

3

1. Spring preload adjusting nut

2. Locknut

3. Special wrench

4-19

4

TIP

● A special wrench can be obtained at a Yamaha

dealer to make this adjustment.

● The spring preload setting is determined by

measuring distance A, shown in the illustration.
The shorter distance A is, the higher the spring
preload; the longer distance A is, the lower the
spring preload. With each complete turn of the

4

adjusting nut, distance A is changed by 1.5 mm
(0.06 in).

1

Spring preload setting:

Minimum (soft):

Distance A = 243.0 mm (9.57 in)

Standard:

Distance A = 233.0 mm (9.17 in)

Maximum (hard):

Distance A = 228.0 mm (8.98 in)

1. Distance A

3. Tighten the locknut to the specified torque.

NOTICE: Always tighten the locknut
against the adjusting nut, and then tighten
it to the specified torque.

[ECB00081]

Tightening torque:

Locknut:

42 Nm (4.2 m·kgf, 30 ft·lbf)

4-20

Rebound damping force

Turn the rebound damping force adjusting screw in
direction (a) to increase the rebound damping
force and thereby harden the damping, and in di­rection (b) to decrease the rebound damping force
and thereby soften the damping.

(b)

(a)

Rebound damping setting:

Minimum (soft):

20 click(s) in direction (b)*

Standard:

13 click(s) in direction (b)*

Maximum (hard):

3 click(s) in direction (b)*

* With the adjusting screw fully turned in direc-

tion (a)

4

1

1. Rebound damping force adjusting screw

2. Position indicator marks

2

TIP

Make sure that the position indicator marks are
aligned when the shock absorber assembly is set
to the standard setting.

Compression damping force

Compression damping force (for fast compression
damping)
To increase the compression damping force and
thereby harden the compression damping, turn the
compression damping force adjusting bolt in direc­tion (a). To decrease the compression damping
force and thereby soften the compression damp­ing, turn the adjusting bolt in direction (b).

4-21

(b)

2

4

1

1. Compression damping force adjusting bolt (for fast
compression damping)

2. Position indicator marks

(a)

1

Compression damping setting (for fast com­pression damping):

Minimum (soft):

Adjusting bolt 4 turn(s) out from the fully
turned in position

Standard:

Adjusting bolt 2 turn(s) out from the fully
turned in position

Maximum (hard):

Adjusting bolt fully turned in

TIP

Make sure that the position indicator marks are
aligned when the shock absorber assembly is set
to the standard setting.

Compression damping force (for slow compres­sion damping)
To increase the compression damping force and
thereby harden the compression damping, turn the
compression damping force adjusting screw in di­rection (a). To decrease the compression damping
force and thereby soften the compression damp­ing, turn the adjusting screw in direction (b).

(b)

(a)

1

1. Compression damping force adjusting screw (for slow
compression damping)

4-22

Compression damping setting (for slow com­pression damping):

Minimum (soft):

16 click(s) in direction (b)*

Standard:

11 click(s) in direction (b)*

Maximum (hard):

1 click(s) in direction (b)*

* With the adjusting screw fully turned in direc-

tion (a)

TIP

Although the total number of clicks of a damping
force adjusting mechanism may not exactly match
the above specifications due to small differences in
production, the actual number of clicks always rep­resents the entire adjusting range. To obtain a pre­cise adjustment, it would be advisable to check the
number of clicks of each damping force adjusting
mechanism and to modify the specifications as
necessary.

EWB00430

WARNING

This shock absorber assembly contains highly
pressurized nitrogen gas. Read and under­stand the following information before han­dling the shock absorber assembly.

● Do not tamper with or attempt to open the

cylinder assembly.

● Do not subject the shock absorber assembly

to an open flame or other high heat source.
This may cause the unit to explode due to ex­cessive gas pressure.

● Do not deform or damage the cylinder in any

way. Cylinder damage will result in poor
damping performance.

● Do not dispose of a damaged or worn out

shock absorber assembly yourself. Take the
shock absorber assembly to a Yamaha deal­er for any service.

EWB00011

WARNING

Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.

4

4-23

EBU19201

PRE-OPERATION CHECKS

EBU19224

Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always
follow the inspection and maintenance procedures and schedules described in the Owner’s Manual.

EWB00481

WARNING

Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equip­ment damage. Do not operate the vehicle if you find any problem. If a problem cannot be corrected

5

by the procedures provided in this manual, have the vehicle inspected by a Yamaha dealer.

Before using this vehicle, check the following points:

ITEM ROUTINE PAGE

Fuel

Engine oil

Coolant

Front brake

• Check fuel level in fuel tank, and add recommended fuel if neces­sary.

• Check fuel line for leakage. Correct if necessary.

• Check oil level in engine, and add recommended oil to specified lev-

el if necessary.

• Check ATV for oil leakage. Correct if necessary.

• Check coolant level in reservoir, and add recommended coolant to

specified level if necessary.

• Check cooling system for leakage. Correct if necessary.

• Check operation. If soft or spongy, have Yamaha dealer bleed hy-

draulic system.

• Check brake pads for wear, and replace if necessary.

• Check brake fluid level in reservoir, and add recommended brake

fluid to specified level if necessary.

• Check hydraulic system for leakage. Correct if necessary.

5-1

4-11, 5-3

5-3, 8-12

5-3, 8-17

5-3, 8-28, 8-29, 8-31

ITEM ROUTINE PAGE

• Check operation. If soft or spongy, have Yamaha dealer bleed hy­draulic system.

Rear brake

Clutch

Throttle lever

Control cables • Make sure that operation is smooth. Lubricate if necessary. 8-38

Drive chain

Wheels and tires

Shift pedal

Brake pedal

Brake and clutch levers

Chassis fasteners • Make sure that all nuts, bolts and screws are properly tightened. 5-6
Instruments, lights and

switches

• Check brake pads for wear, and replace if necessary.

• Check brake fluid level in reservoir, and add recommended brake

fluid to specified level if necessary.

• Check hydraulic system for leakage. Correct if necessary.

• Check operation, and correct if necessary.

• Lubricate cable if necessary.

• Check lever free play, and adjust if necessary.

• Make sure that operation is smooth. Lubricate cable and lever hous-

ing if necessary.

• Check cable free play, and adjust if necessary.

• Check chain slack, and adjust if necessary.

• Check chain condition. Lubricate if necessary.

• Check wheel condition, and replace if damaged.

• Check tire condition and tread depth. Replace if necessary.

• Check air pressure. Correct if necessary.

• Make sure that operation is smooth.

• Correct if necessary.

• Make sure that operation is smooth. Lubricate pedal pivoting point if

necessary.

• Make sure that operation is smooth. Lubricate lever pivoting points if
necessary.

• Check operation, and correct if necessary. 5-6

5-3, 8-28, 8-29, 8-32

8-34

5-4, 8-27

5-4, 8-35, 8-37

5-4

8-38

8-39

8-38

5

5-2

EBU19541

Fuel

Make sure that there is sufficient fuel in the tank.
(See page 4-11.)

EBU19560

Engine oil

Make sure that the engine oil is at the specified lev­el. Add oil as necessary. (See page 8-12.)

EBU19631

5

Coolant

Make sure that the coolant is at the specified level.
Add coolant as necessary. (See page 8-17.)

TIP

The coolant level must be checked on a cold en­gine since the level varies with engine tempera­ture.

EBU19711

Front and rear brakes

● Check for correct brake pedal height. (See page

8-32.) If the pedal height is incorrect, have a
Yamaha dealer adjust it.

● Check the operation of the lever and pedal. They

should move smoothly and there should be a
firm feeling when the brakes are applied. If not,
have a Yamaha dealer check the brake system.

Brake fluid level

Check the brake fluid level. Add fluid if necessary.
(See page 8-29.)

Recommended brake fluid:

DOT 4

Brake fluid leakage

Check to see if any brake fluid is leaking out of the
pipe joints or brake fluid reservoirs. Apply the
brakes firmly for one minute. If there is any leak­age, have a Yamaha dealer check the brake sys­tem.

Brake lever and brake pedal

● Check that there is no free play in the brake le-

ver. If there is free play, have a Yamaha dealer
check the brake system.

Brake operation

Test the brakes at slow speed after starting out to
make sure they are working properly. If the brakes
do not provide proper braking performance, check
the brake pads for wear. (See page 8-28.)

5-3

EBU19761

Throttle lever

Check the operation of the throttle lever. It must
open smoothly and spring back to the idle position
when released. Have a Yamaha dealer correct if
necessary.

EBU19770

Drive chain

Check the condition of the drive chain and check
the drive chain slack. Lubricate and adjust the
drive chain as necessary. (See page 8-35.)

EBU19794

Tires

Check tire pressure regularly to make sure it is at
the recommended specifications. Also check for
wear and damage.

Tire pressure

Use the low-pressure tire gauge to check and ad­just tire pressures when the tires are cold. Tire
pressures must be equal on both sides.

WARNING! Operation of this vehicle with im­proper tire pressure may cause severe injury
or death from loss of control or rollover. Tire
pressure below the minimum specified could

also cause the tire to dislodge from the rim un­der severe riding conditions.

[EWB02541] Set tire

pressures to the following specifications:

Recommended tire pressure:

Front

27.5 kPa (0.275 kgf/cm², 4.0 psi)

Rear

27.5 kPa (0.275 kgf/cm², 4.0 psi)

Minimum tire pressure:

Front

24.5 kPa (0.245 kgf/cm², 3.6 psi)

Rear

24.5 kPa (0.245 kgf/cm², 3.6 psi)

Maximum tire seating pressure:

Front

250 kPa (2.5 kgf/cm², 36 psi)

Rear

250 kPa (2.5 kgf/cm², 36 psi)

The low-pressure tire gauge is included as stan­dard equipment. Make two measurements of the
tire pressure and use the second reading. Dust or
dirt in the gauge could cause the first reading to be
incorrect.

5

5-4

5

1. Low-pressure tire gauge

1. Tire wear limit

Tire wear limit

When the tire groove decreases to 3 mm (0.12 in)
due to wear, replace the tire.

Tire information

This ATV is equipped with tubeless tires with
valves.

EWB02551

WARNING

Use of improper tires on this ATV may cause
loss of control, increasing your risk of an acci­dent.

After extensive tests, only the tires listed below
have been approved for this model by Yamaha
Motor Co., Ltd.

5-5

Front:

Manufacturer/model:

DUNLOP/KT341 Radial

Size:

AT21 x 7R10

Ty p e:

Tu b el e ss

Rear:

Manufacturer/model:

DUNLOP/KT345 Radial

Size:

AT20 x 10R9

Ty p e:

Tu b el e ss

Aftermarket tires and rims

The tires and rims that came with your ATV were
designed to match the performance capabilities
and to provide the best combination of handling,
braking, and comfort. Other tires, rims, sizes, and
combinations may not be appropriate.

EBU19840

Chassis fasteners

Make sure that all nuts, bolts and screws are prop­erly tightened.

EBU19850

Instruments, lights and switches

Check that all instruments, lights and switches are
working properly. Correct if necessary.

5

5-6

EBU19872

OPERATION

EWB00011

WARNING

Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.

EBU19901

Read the Owner’s Manual carefully before riding
the ATV. If there is a control or function you do not
understand, ask your Yamaha dealer.

6

EWB00631

WARNING

Read the Owner’s Manual carefully to become
familiar with all controls in order to help pre­vent any loss of control, which could cause an
accident or injury.

EBU29483

Starting the engine

ECB00150

NOTICE

See the “Engine break-in” section on page 6-5
prior to operating the engine for the first time.

1. Set the parking brake.

2. Turn the key to “ON” and the engine stop
switch to “”.
The following warning lights should come on
for a few seconds, then go off.

● Coolant temperature warning light

● Fuel level warning light

● Engine trouble warning light

ECB00824

NOTICE

If a warning light does not go off, see page 4-2
for the corresponding warning light circuit
check. To avoid possible damage, do not oper­ate the ATV if a warning light stays on.

3. Shift the transmission into neutral. The neutral
indicator light should come on, if it does not
come on, have a Yamaha dealer check the
electrical circuit.

TIP

This model is equipped with an ignition circuit cut­off system. The engine can be started under the
following conditions.

● The transmission is in neutral.

6-1

● The clutch is disengaged with the transmission

in gear. However, it is recommended to shift into
neutral before starting the engine.

reverse, make sure there are no people or ob­stacles behind you. When it is safe to proceed,
go slowly.

4. Completely close the throttle lever and start
the engine by pushing the start switch.

NOTICE: For maximum engine life, never
accelerate hard when the engine is cold!

[ECB00162]

TIP

If the engine fails to start, release the start switch,
then push it again. Pause a few seconds before
the next attempt. Each cranking should be as short
as possible to preserve battery energy. Do not
crank the engine more than 10 seconds on each
attempt.

EBU20501

Operating the reverse knob and driving in reverse

EWB00720

WARNING

Improper operation in reverse could make you
hit an obstacle or even a person behind you,
resulting in serious injury. When you shift into

ECB00170

NOTICE

Before shifting, stop the ATV, otherwise the
transmission may be damaged.

1. Bring the ATV to a complete stop, apply the
clutch lever, and then shift the transmission
into first gear.

2. While applying the brake pedal, turn the re­verse knob clockwise with your right hand.

3. Apply the clutch lever and shift the transmis­sion into reverse by pressing down on the shift
pedal, and then release the reverse knob.

6-2

6

1

2

6

1. Reverse knob “REV”

2. Shift pedal

TIP

When in reverse, the reverse indicator light should
come on. If the indicator light does not come on,
have a Yamaha dealer check the electrical circuit.

4. Check behind you for people or obstacles,
and then release the brake pedal.

5. Open the throttle lever gradually and release
the clutch lever slowly. Continue to watch to
the rear while backing.

EBU20531

Shifting

This ATV has a 5-speed forward and 1-speed re­verse transmission. The transmission allows you
to control the amount of power you have available
at a given speed or for starting, accelerating, climb­ing hills, etc.
To shift into neutral, return the throttle lever to the
closed position, apply the clutch, and then repeat­edly depress the shift pedal until it stops.
When it stops, it will be in first gear. Raise the pedal
slightly to reach the neutral position.

5
4
3
2

N

1

2

R

3

1. Shift pedal

2. Neutral position

3. Reverse position

1

6-3

EBU20571

To start out and accelerate

1. Release the throttle lever.

ECB00200

NOTICE

Always close the throttle before shifting gears,
otherwise damage to the engine and drive train
may result.

2. Pull the clutch lever to disengage the clutch.

3. Shift into first gear.

4. Open the throttle gradually and at the same
time, release the clutch lever slowly.

WARNING! Opening the throttle abruptly
or releasing the clutch lever too quickly
could make the ATV wheelie, which would
increase the chance of an accident, includ­ing an overturn.

[EWB00731]

5. Once the ATV has attained adequate speed,
release the throttle, and at the same time,
quickly pull in the clutch lever.

6. Shift the transmission into second gear.
(Make sure not to shift the transmission into
neutral.)

7. Open the throttle part way and gradually re­lease the clutch lever.

8. Follow the same procedure when shifting to
the next higher gear.

EBU20650

To decelerate

When slowing down or stopping, release the throt­tle and apply the brakes smoothly and evenly. As
you slow down, shift to a lower gear. Be sure that
the engine has sufficiently slowed before engaging
a lower gear. Improper use of the brakes or shifting
can cause the tires to lose traction, reducing con­trol and increasing the possibility of an accident.

EWB00710

WARNING

Make sure the engine has sufficiently slowed
before shifting to a lower gear. Engaging a low­er gear when the engine speed is too high
could make the wheels stop rotating and lose
traction. This could cause loss of control, an
accident and injury. It could also cause engine
or drive train damage.

ECB00180

NOTICE

● Even with the transmission in the neutral po-

sition, do not coast for long periods of time
with the engine off, and do not tow the ATV

6

6-4

for long distances. The transmission is prop­erly lubricated only when the engine is run­ning. Inadequate lubrication may damage
the transmission.

● Always use the clutch when changing gears.

The engine, transmission and drive train are
not designed to withstand the shock of
forced shifting and can be damaged by shift­ing without using the clutch.

polish themselves to the correct operating clear­ances. During this period, prolonged full-throttle
operation or any condition that might result in en­gine overheating must be avoided.

0–160 km (0–100 mi) or 0–10 hours

Avoid prolonged operation above 1/2 throttle. Vary
the speed of the ATV regularly. Do not operate it at
one set throttle position.

EBU20672

Engine break-in

6

TIP

● For ATVs equipped with an odometer or an hour

meter, follow the figures given in km (mi) or the
figures given in hours.

● For ATVs not equipped with an odometer or

hour meter, follow the figures given in hours.

There is never a more important period in the life of
your engine than the first 320 km (200 mi) or 20
hours of riding. For this reason, you should read
the following material carefully.
Since the engine is brand new, do not put an ex­cessive load on it for the first 320 km (200 mi) or 20
hours. The various parts in the engine wear and

160–320 km (100–200 mi) or 10–20 hours

Avoid prolonged operation above 3/4 throttle. Rev
the engine through the gears freely, but do not use
full throttle at any time.

320 km (200 mi) or 20 hours and beyond

The ATV can now be operated normally.

ECB00220

NOTICE

If any engine trouble should occur during the
engine break-in period, immediately have a
Yamaha dealer check the ATV.

EBU26760

Parking

When parking the ATV, stop the engine, shift into
first gear, and then apply the parking brake.

6-5

1. Locked position

EBU20900

Parking on a slope

EWB00870

WARNING

Avoid parking on hills or other inclines. Park­ing on a hill or other incline could cause the
ATV to roll out of control, increasing the
chance of an accident. If you must park on an
incline, place the ATV transversely across the
incline, apply the parking brake, stop the en­gine, shift into first gear, and then block the
front and rear wheels with rocks or other ob­jects.

Do not park the ATV at all on hills that are so
steep you could not walk up them easily.

1. Bring the ATV to a stop by applying the front
brake.

2. With the front and rear brake applied, pull the
clutch lever, shift into the neutral position, re­lease the clutch lever, and then apply the
parking brake.

3. Stop the engine by setting the engine stop
switch to “”.

4. With the front and rear brakes applied, pull the
clutch lever, shift into first gear, and then re­lease the clutch lever, brake lever and brake
pedal.

TIP

Make sure that the neutral indicator light goes off.

5. Turn the key to “OFF”.

6

6-6

EBU20910

6

Accessories and loading

EBU20921

Genuine Yamaha Accessories

Choosing accessories for your ATV is an important
decision. Genuine Yamaha Accessories, which
are available only from a Yamaha dealer, have
been designed, tested, and approved by Yamaha
for use on your ATV. Many companies with no con­nection to Yamaha manufacture parts and acces­sories or offer other modifications for Yamaha
vehicles. Yamaha is not in a position to test the
products that these aftermarket companies pro­duce. Therefore, Yamaha can neither endorse nor
recommend the use of accessories not sold by

Yamaha or modifications not specifically recom­mended by Yamaha, even if sold and installed by
a Yamaha dealer.

Aftermarket parts, accessories, and modifica­tions

While you may find aftermarket products similar in
design and quality to genuine Yamaha Accesso­ries, recognize that some aftermarket accessories
or modifications are not suitable because of poten­tial safety hazards to you or others. Installing after­market products or having other modifications
performed to your ATV that change any of the ve­hicle’s design or operation characteristics can put
you and others at greater risk of serious injury or
death. You are responsible for injuries related to
changes in the vehicle.
Keep the following in mind when considering an
accessory or operating an ATV which has acces­sories.

● Accessories should be rigidly and securely

mounted. An accessory which can shift position
or come off while you are riding could affect your
ability to control the ATV.

● Do not mount an accessory where it could inter-

fere with your ability to control the ATV. Exam­ples include (but are not limited to) a heavy or

6-7

bulky object attached to the handlebars which
could make steering difficult, an accessory that
limits your ability to move around on the seat, or
one that limits your view.

● Use extra caution when riding an ATV with ac-

cessories. The ATV may handle differently than
it does without accessories.

EBU20941

Loading

EWB00820

WARNING

Never exceed the stated load capacity for this
ATV. Overloading this ATV or carrying or tow­ing cargo improperly could cause changes in
ATV handling which could lead to an accident.
Cargo should be properly distributed and se­curely attached. Reduce speed when carrying
cargo or pulling a trailer. Allow greater dis­tance for braking.

As originally equipped, this ATV is not designed to
carry cargo or tow a trailer. If you choose to add ac­cessories so that you can carry cargo or tow a trail­er, you must use common sense and good

judgment as the stability and handling of an ATV
can be changed. When adding accessories, keep
the following points in mind:

● Never exceed the weight limits shown. An over-

loaded ATV can be unstable.

MAXIMUM LOADING LIMIT

ATV loading limit (total weight of rider, cargo,
accessories, and tongue):

100.0 kg (220 lb)

● If you are carrying cargo and towing a trailer, in-

clude the tongue weight in the maximum ATV
load limit.

● Load cargo on the carriers as close to the center

of the ATV as possible. Put cargo at the rear of
the front carrier, at the front of the rear carrier,
and center it.

● Tie down cargo securely to the carriers. Make

sure cargo in the trailer cannot move around. A
shifting load can cause an accident.

● Make sure the load does not interfere with con-

trols or your ability to see where you are going.

● Ride more slowly than you would without a load.

The more weight you carry, the slower you
should go. Although conditions vary, it is good

6

6-8

practice not to exceed 2nd gear whenever you
are carrying heavier loads or when towing a trail­er.

● Allow more braking distance. A heavier ATV

takes longer to stop.

● Avoid making sharp turns unless at very slow

speeds.

● Avoid hills and rough terrain. Choose terrain

carefully. Added weight affects the stability and
handling of the ATV.

6

EWB00011

WARNING

Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.

6-9

EBU21132

RIDING YOUR ATV

7

7-1

EWB00011

WARNING

Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.

EBU21595

GETTING TO KNOW YOUR ATV

This ATV is intended for recreational use by expe­rienced operators only. This section, Riding your
ATV, provides general ATV riding instructions for
recreational riding. The skills and techniques de­scribed in this section, however, are appropriate

7

for all types of riding. Riding your ATV requires
special skills acquired through practice over a pe­riod of time. Take the time to learn the basic tech­niques well before attempting more difficult
maneuvers.
Riding your new ATV can be a very enjoyable ac­tivity, providing you with hours of pleasure. But it is
essential to familiarize yourself with the operation
of the ATV to achieve the skill necessary to enjoy
riding safely. Before you begin to ride, be sure you
have read this Owner’s Manual completely and un­derstand the operation of the controls. Pay partic-

ular attention to the safety information on pages
2-1–2-4. Also read all warning and notice labels on
your ATV.

RIDE WITH CARE AND GOOD JUDGMENT

Get training if you are inexperienced.

EWB01381

WARNING

● Do not operate this ATV or allow anyone else

to operate it without proper instruction. The
risk of an accident is greatly increased if the
operator does not know how to operate the
ATV properly in different situations and on
different types of terrain.

● Do not operate this ATV at speeds too fast

for your skills or the conditions, as this in­creases your chances of losing control of
the ATV and an accident. Always go at a
speed that is proper for the terrain, visibility
and operating conditions, and your experi­ence.

Beginning and inexperienced operators should
complete the certified training course offered by
Yamaha. They should then regularly practice the
skills learned in the course and the operating tech-

7-2

niques described in this Owner’s Manual. For more
information about the training course, contact an
authorized ATV dealer or call 1-800-887-2887.

Riding your ATV requires skills acquired
through practice over a period of time.

Do not attempt to operate at maximum perfor­mance until you are totally familiar with the ATV’s
handling and performance characteristics. Take
the time to learn the basic techniques well before
attempting more difficult maneuvers. Become fa­miliar with this ATV at slow speeds first, even if you
are an experienced operator.

Not recommended for children under 16 years
of age.

EWB01390

WARNING

A child under 16 should never operate an ATV
with engine size greater than 90 cc. Use by chil­dren of ATVs that are not recommended for
their age can lead to severe injury or death of
the child.

This ATV is designed to carry the operator only
– passengers prohibited.

The long seat is to allow the operator to shift posi­tion as needed during operation. It is not for carry­ing passengers. WARNING! Never carry a

passenger. Carrying a passenger on this ATV
greatly reduces your ability to balance and
control this ATV. You could have an accident,
resulting in severe injury or death to you
and/or your passenger.

[EWB01401]

7

7-3

7

Apparel

Always wear the following to reduce risk of injury in
an accident:

● Approved motorcycle helmet that fits properly

● Eye protection (goggles, helmet face shield, or

protective eyewear)

● Over-the-ankle boots, gloves, long-sleeved shirt

or jacket, and long pants
An approved helmet and other personal protective
equipment can reduce the severity of injuries in an
accident. WARNING! Operating without an ap-

proved motorcycle helmet increases your
chances of a severe head injury or death in the
event of an accident.

[EWB01411]

Wear eye protection when operating your ATV to
reduce the risk of a serious accident or injury. Eye
protection, such as a face shield or goggles, may
reduce the risk of foreign material getting in your
eyes and help prevent loss of vision. WARNING!

Operating without eye protection can result in
an accident and increases your chances of a
severe injury in the event of an accident.

[EWB02611]

7-4

1. Protective clothing

2. Goggles

3. Gloves

4. Boots

5. Helmet

Do not operate after or while consuming alco­hol or drugs.

The operator’s performance capability is reduced
by the influence of alcohol or drugs. Consuming al­cohol or drugs could seriously affect your judg­ment, cause you to react more slowly, and affect
your balance and perception. WARNING! Never

consume alcohol or drugs before or while driv­ing this ATV. You increase your chance of an
accident.

[EWB01421]

Pre-operation checks

Always inspect your ATV each time you use it to
make sure the ATV is in safe operating condition.
Perform the pre-operation checks listed on page
5-1. Always follow the inspection and maintenance
procedures and schedules described in the Own­er’s Manual. WARNING! Failure to inspect the

ATV before operating it and to maintain it prop­erly increases the possibility of an accident or
equipment damage.

[EWB01431]

Speed limiter

For riders less experienced with this model, the
throttle lever housing is equipped with a speed lim­iter. The speed limiter keeps the throttle from fully

7-5

7

opening, even when the throttle lever is pushed to
the maximum. Turning in the adjusting screw limits
the maximum engine power available and de­creases the maximum speed of the ATV. Turning
in the adjusting screw decreases top speed, and
turning it out increases top speed. (See page 4-7.)

12

7

1. Locknut

2. Adjusting screw

Loading and accessories

As originally equipped, this ATV is not designed to
carry cargo or tow a trailer. If you choose to add ac­cessories to carry cargo, you must use common
sense and good judgment.

Use extra caution when riding the ATV with addi­tional loads, such as accessories or cargo. The
ATV’s handling may be adversely affected. Re­duce your speed when adding additional loads.

EWB00971

WARNING

Improper loading or towing can increase the
risk of loss of control, an overturn, or other ac­cident. To reduce the risk of an accident:

● Do not exceed the maximum loading limits

for the vehicle (see box in this section or ve­hicle labeling).

● Make sure the load does not interfere with

your control or ability to see where you are
going.

● Reduce speed and allow more room to stop.

A heavier vehicle takes longer to stop.

● Avoid hills and rough terrain. Choose terrain

carefully. Use extreme caution when towing
or carrying a load on inclines.

● Turn gradually and go slowly.

MAXIMUM LOADING LIMIT

ATV loading limit (total weight of cargo, rider,
accessories, and tongue):

100.0 kg (220 lb)

7-6

During operation

Always keep your feet on the footboards during op­eration; otherwise, they may contact the rear
wheels. WARNING! Removing even one hand

or foot can reduce your ability to control the
ATV or could cause you to lose your balance
and fall off of the ATV. If you remove a foot
from a footboard, your foot or leg may come
into contact with the rear wheels, which could
injure you or cause an accident.

[EWB01471]

Avoid wheelies and jumping. WARNING! At-

tempting wheelies, jumps, and other stunts in­creases the chance of an accident, including
an overturn. Never attempt stunts, such as
wheelies or jumps. Don’t try to show off.

[EWB01481]

7

Modifications and accessories

Never modify this ATV through improper installa­tion or use of accessories or other modification. All
parts and accessories added to this ATV should be
genuine Yamaha or equivalent components de­signed for use on this ATV and should be installed
and used according to instructions. If you have
questions, consult an authorized ATV dealer.

7-7

WARNING! Operating this ATV with improper
modifications may cause changes in handling
which in some situations could lead to an acci­dent.

[EWB01491]

Exhaust system

EWB01501

WARNING

● Dry grass or brush or other combustible ma-

terial accumulated around the engine area

could catch fire. Do not operate, idle, or park

the ATV in dry grass or other dry ground cov-

er. Keep the engine area free of dry grass,

brush, or other combustible material.

7

● Someone touching the exhaust system dur-

ing or after operation could be burned. Do

not touch the hot exhaust system. Do not

park the ATV in a place where others might

be likely to touch it.

The muffler and other engine parts become ex­tremely hot during operation and remain hot after
the engine has stopped. To reduce the risk of fire
during operation or after leaving the ATV, do not let
brush, grass and other materials collect under the
vehicle, near the muffler or exhaust pipe, or next to
other hot parts. Check under the vehicle after op-

erating in areas where combustible materials may
have collected. Do not idle or park the vehicle in
long dry grass or other dry ground cover.
To prevent burns, avoid touching the exhaust sys­tem. Park the ATV in a place where pedestrians or
children are not likely to touch it.

7-8

BE CAREFUL WHERE YOU RIDE

This ATV is designed for off-road use only.

WARNING! Paved surfaces may seriously af­fect handling and control of the ATV, and may
cause the ATV to go out of control. Always
avoid paved surfaces, including sidewalks,
driveways, parking lots and streets.

[EWB01511]

Do not ride on any public road, street, or highway.
Riding on public roads can result in collisions with
other vehicles. In many states it is illegal to operate
ATVs on public streets, roads and highways.

WARNING! Never operate this ATV on any pub­lic street, road or highway, even a dirt or gravel
one. You could collide with another vehicle.

[EWB01031]

7

7-9

Know the terrain where you ride. Ride cautiously in
unfamiliar areas. Stay alert for holes, rocks, or
roots in the terrain, and other hidden hazards
which may cause the ATV to upset. WARNING!

The ATV could go out of control if you do not
have enough time to react to hidden rocks,
bumps, or holes. Go slowly and be extra care­ful when operating on unfamiliar terrain. Al­ways be alert to changing terrain conditions
when operating the ATV.

[EWB01531]

7

Do not operate on rough, slippery, or loose terrain
until you have learned and practiced the skills nec­essary to control the ATV on such terrain. Always
be especially cautious on these kinds of terrain.

WARNING! Failure to use extra care when op­erating on excessively rough, slippery, or
loose terrain could cause loss of traction or
ATV control, which could result in an accident,
including an overturn.

[EWB01541]

7-10

When riding in an area where you might not easily
be seen, such as desert terrain, mount a caution
flag on the ATV. DO NOT use the flag pole bracket
as a trailer hitch. WARNING! You could collide

with another vehicle if operating in off-road ar­eas where you cannot easily be seen. Mount a
caution flag on the ATV to make you more vis­ible. Watch carefully for other vehicles.

[EWB01061]

Do not ride in areas posted “no trespassing”.
Do not ride on private property without getting per­mission.

Select a large, flat area off-road to become familiar
with your ATV. Make sure that this area is free of
obstacles and other riders. You should practice
control of the throttle, brakes, shifting procedures,
and turning techniques in this area before trying
more difficult terrain.

7-11

7

Set the parking brake and follow the instruction on
page 6-1 to start the engine. Once it has warmed
up you are ready to begin riding your ATV. As you
get on the ATV, be sure not to accidentally move
the shift pedal. With the engine idling, pull the
clutch lever to disengage the clutch and shift into
1st gear, and then release the parking brake. Open
the throttle gradually, and at the same time, re­lease the clutch lever slowly. Once the ATV has at­tained adequate speed, release the throttle lever
and at the same time, quickly pull in the clutch le­ver and shift into 2nd gear. Open the throttle part
way and gradually release the clutch. WARNING!

If the throttle is applied too abruptly or if the

7

throttle is not released during shifting, or if the
shift pedal is not released before applying the
throttle, the front wheels may lift off the
ground, resulting in a loss of directional con­trol.

[EWB02631] NOTICE: Do not shift gears without

releasing the throttle. Damage to the engine or
drive train may occur.

[ECB01071]

Use this same procedure as you move into the
higher gears. Be sure to coordinate the use of the
throttle and shift pedal properly.
Avoid higher speeds until you are thoroughly famil­iar with the operation of your ATV.

When slowing down or stopping, release the throt­tle and apply the brakes smoothly and evenly. As
you slow down, shift to a lower gear. Be sure that
the engine has sufficiently slowed before engaging
a lower gear. Improper use of the brakes or shifting
can cause the tires to lose traction, reducing con­trol and increasing the possibility of an accident.

TURNING YOUR ATV

EWB01771

WARNING

Always follow proper procedures for turning
as described in this Owner’s Manual. Practice
turning at low speeds before attempting to turn
at faster speeds. Do not turn at speeds too fast
for your skills or the conditions. ATV could go
out of control, causing a collision or overturn.

To achieve maximum traction while riding off-road,
the two rear wheels turn together at the same
speed. Therefore, unless the wheel on the inside
of the turn is allowed to slip or lose some traction,
the ATV will resist turning. A special turning tech­nique must be used to allow the ATV to make turns
quickly and easily. It is essential that this skill be
learned first at low speed.

7-12

As you approach a curve, slow down and begin to
turn the handlebars in the desired direction. As you
do so, put your weight on the footboard to the out­side of the turn (opposite your desired direction)
and lean your upper body into the turn. Use the
throttle to maintain an even speed through the turn.
This maneuver will let the wheel on the inside of
the turn slip slightly, allowing the ATV to make the
turn properly.

1. Lean towards inside of turn.

2. Support your weight on the outer footrest.

This procedure should be practiced at slow speed
many times in a large off-road area with no obsta­cles. If an incorrect technique is used, your ATV
may continue to go straight. If the ATV doesn’t
turn, come to a stop and then practice the proce­dure again. If the riding surface is slippery or loose,
it may help to position more of your weight over the
front wheels by moving forward on the seat.
Once you have learned this technique, you should
be able to perform it at higher speeds or in tighter
curves.
Improper riding procedures such as abrupt throttle
changes, excessive braking, incorrect body move­ments, or too much speed for the sharpness of the
turn may cause the ATV to tip. If the ATV begins to
tip over to the outside while negotiating a turn, lean
more to the inside. It may also be necessary to
gradually let off on the throttle and steer to the out­side of the turn to avoid tipping over.
Remember: Avoid higher speeds until you are
thoroughly familiar with the operation of your ATV.

7

7-13

CLIMBING UPHILL

EWB01591

WARNING

Climbing hills improperly can cause overturns
or loss of control. Use proper riding tech­niques described in this Owner’s Manual.

● Never operate the ATV on hills too steep for

the ATV or for your abilities. The ATV can

overturn more easily on extremely steep hills

than on level surfaces or small hills.

● Always check the terrain carefully before

you start up any hill. Never climb hills with

excessively slippery or loose surfaces.

● Shift your weight forward.

7

● Never open the throttle suddenly or make

sudden gear changes. The ATV could flip

over backwards.

● Never go over the top of any hill at high

speed. An obstacle, a sharp drop, or another

vehicle or person could be on the other side

of the hill.

● Never attempt to turn the ATV around on any

hill until you have mastered the turning tech-

nique as described in the Owner’s Manual on

level ground. Be very careful when turning

on any hill.

● Avoid crossing the side of a steep hill if pos-

sible. When crossing the side of a hill, shift
your weight to the uphill side of the ATV.

7-14

Do not attempt to climb hills until you have mas­tered basic maneuvers on flat ground. Always
check the terrain carefully before attempting any
hill. In all cases avoid inclines with slippery or loose
surfaces, or obstacles that might cause you to lose
control.
To climb a hill, you need traction, momentum, and
steady throttle. Travel fast enough to maintain mo­mentum, but not so fast that you cannot react to
changes in the terrain as you climb.

It is important when climbing a hill to make sure
that your weight is transferred forward on the ATV.
This can be accomplished by leaning forward and,
on steeper inclines, standing on the footboards
and leaning forward over the handlebars. Whenev­er possible, ride straight up hills.
Slow down when you reach the crest of the hill if
you cannot see clearly what is on the other side –
there could be another person, an obstacle, or a
sharp drop-off. Use common sense and remember
that some hills are too steep for you to climb or de­scend.
If you are climbing a hill and you find that you have
not properly judged your ability to make it to the
top, you should turn the ATV around while you still
have forward motion (provided you have the room
to do so) and go down the hill.
If your ATV has stalled or stopped and you believe
you can continue up the hill, restart carefully to
make sure you do not lift the front wheels which
could cause you to lose control. If you are unable
to continue up the hill, dismount the ATV on the up­hill side. Physically turn the ATV around and then
descend the hill.

7

7-15

If you start to roll backwards, DO NOT apply the
rear brake, and apply the front brake gradually.
The ATV could easily tip over backwards. When
fully stopped, apply the rear brake as well, and
then lock the parking brake. Dismount the ATV im­mediately on the uphill side or to a side if pointed
straight uphill. Turn the ATV around and remount,
following the procedure described in the Owner’s
Manual. WARNING! Stalling, rolling backwards

or improperly dismounting while climbing a hill
could result in ATV overturning. If you cannot
control the ATV, dismount immediately on the
uphill side.

[EWB01802]

7

RIDING DOWNHILL

EWB01131

WARNING

Going down a hill improperly could cause
overturns or loss of control. Always follow
proper procedures for going down hills as de­scribed in this Owner’s Manual.

● Always check the terrain carefully before

you start down any hill.

7-16

● Never operate the ATV on hills too steep for

the ATV or for your abilities. The ATV can
overturn more easily on extremely steep hills
than on level surfaces or small hills.

● Shift your weight backward and to the up

side of the hill.

● Never go down a hill at high speed.

● Avoid going down a hill at an angle that

would cause the ATV to lean sharply to one
side. Go straight down the hill where possi­ble.

● Improper braking can cause the wheels on

the uphill side to come off the ground or
cause loss of traction. Gradually apply only
the rear brake when going downhill.

When riding your ATV downhill, shift your weight
as far to the rear and uphill side of the ATV as pos­sible. Move back on the seat and sit with your arms
straight. Choose a low gear which will allow the en­gine compression to do most of the braking for you.
Use caution while descending a hill with loose or
slippery surfaces. Braking ability and traction may
be adversely affected by these surfaces. Improper
braking may also cause a loss of traction. Gradual­ly apply only the rear brake.

Whenever possible, ride your ATV straight down­hill. Avoid sharp angles which could allow the ATV
to tip or roll over. Carefully choose your path and
ride no faster than you will be able to react to ob­stacles which may appear.

7

7-17

CROSSING A SLOPE

EWB01632

WARNING

Improperly crossing hills or turning on hills
could cause loss of control or cause the ATV to
overturn.

● Always follow proper procedures as de-

scribed in the Owner’s Manual.

● Avoid hills with excessively slippery or loose

surfaces.

● Avoid crossing the side of a steep hill.

● Shift your weight to the uphill side of the

ATV.

● Never attempt to turn the ATV around on any

7

hill until you have mastered the turning tech-

nique as described in the Owner’s Manual on

level ground. Be very careful when turning

on any hill.

Traversing a sloping surface on your ATV requires
you to properly position your weight to maintain
proper balance. Be sure that you have learned the
basic riding skills on flat ground before attempting
to cross a sloping surface. Avoid slopes with slip­pery surfaces or rough terrain that may upset your
balance.

As you travel across a slope, lean your body in the
uphill direction. It may be necessary to correct the
steering when riding on loose surfaces by pointing
the front wheels slightly uphill. When riding on
slopes, be sure not to make sharp turns either up
or down hill.
If your ATV does begin to tip over, gradually steer
in the downhill direction if there are no obstacles in
your path. As you regain proper balance, gradually
steer again in the direction you wish to travel.

7-18

CROSSING THROUGH SHALLOW WATER

EWB01641

WARNING

Operating this vehicle through deep or fast­flowing water can lead to loss of control or an
overturn. To reduce your risk of drowning or
other injuries, use care when crossing through
water. Never operate this ATV water deeper
than the depth specified in your Owner’s Man­ual, as tires may float, increasing the risk of an
overturn.

The ATV can be used to cross slow moving, shal­low water of up to a maximum of 35 cm (14 in) in
depth. Before entering the water, choose your path
carefully. Enter where there is no sharp drop off,
and avoid rocks or other obstacles which may be
slippery or upset the ATV. Drive slowly and care­fully.

Test your brakes after leaving the water. If neces­sary, apply them several times to let friction dry out
the linings. Do not continue to ride your ATV with­out verifying that you have regained proper braking
ability. WARNING! Wet brakes may have re-

duced stopping ability, which could cause loss
of control.

[EWB02621]

7

7-19

1. Air filter case check hose

1

7

After riding your ATV in water, be sure to drain the
trapped water by removing the check hose at the
bottom of the air filter case. NOTICE: Undrained

water can cause damage or improper opera­tion.

[ECB00841]

Wash the ATV in fresh water if it has been operat­ed in salt water or muddy conditions.

RIDING OVER ROUGH TERRAIN

EWB01651

WARNING

Riding improperly over obstacles could cause
loss of control or a collision. Before operating
in a new area, check for obstacles. Never at­tempt to ride over large obstacles, such as
large rocks or fallen trees. When you go over
obstacles, always follow proper procedures as
described in the Owner’s Manual.

Riding over rough terrain should be done with cau­tion. Look out for obstacles which could cause
damage to the ATV or could lead to an upset or ac-

7-20

cident. Be sure to keep your feet firmly mounted on
the footboards at all times. Avoid jumping the ATV
as loss of control and damage to the ATV may re­sult.

SLIDING AND SKIDDING

EWB01662

WARNING

Skidding or sliding improperly may cause you
to lose control of this ATV. You may also re­gain traction unexpectedly, which may cause
the ATV to overturn.

● Learn to safely control skidding or sliding by

practicing at low speeds and on level,
smooth terrain.

● On extremely slippery surfaces, such as ice,

go slowly and be very cautious in order to re­duce the chance of skidding or sliding out of
control.

Care should be used when riding on loose or slip­pery surfaces since the ATV may slide. If unex­pected and uncorrected, sliding could lead to an
accident.
To reduce the tendency for the front wheels to slide
in loose or slippery conditions, positioning your
weight over the front wheels will sometimes help.

If the rear wheels of your ATV start to slide side­ways, control can usually be regained (if there is
room to do so) by steering in the direction of the
slide. Applying the brakes or accelerating is not
recommended until you have corrected the slide.

7-21

7

With practice, over a period of time, skill at con­trolled sliding can be developed. The terrain

7

should be chosen carefully before attempting such
maneuvers, since both stability and control are re­duced. Bear in mind that sliding maneuvers should
always be avoided on extremely slippery surfaces
such as ice, since all control may be lost.

WHAT TO DO IF...

This section is designed to be a reference guide
only. Be sure to read each section on riding tech­niques completely.

WHAT TO DO...

● If your ATV doesn’t turn when you want it to:

Bring the ATV to a stop and practice the turning
maneuvers again. Be sure you are putting your
weight on the footboard to the outside of the
turn. Position your weight over the front wheels
for better control. (See page 7-12.)

● If your ATV begins to tip while turning:

Lean more into the turn to regain balance. If nec­essary, gradually let off the throttle and/or steer
to the outside of the turn. (See page 7-12.)

● If your ATV starts to slide sideways:

Steer in the direction of the slide if you have the
room. Applying the brakes or accelerating is not
recommended until you have corrected the
slide. (See page 7-21.)

● If your ATV can’t make it up a hill you are trying

to climb:
Turn the ATV around if you still have forward
speed. If not, stop, dismount on the uphill side of
the ATV and physically turn the ATV around. If
the ATV starts to slip backwards, DO NOT USE
THE REAR BRAKE – the ATV may tip over on
top of you. Dismount the ATV on the uphill side.
(See page 7-14.)

7-22

● If your ATV is traversing a sloping surface:

Be sure to ride with your weight positioned to­wards the uphill side of the ATV to maintain
proper balance. If the ATV starts to tip, steer
down the hill (if there are no obstacles in your
way) to regain balance. If you discover that the
ATV is going to tip over, dismount on the uphill
side. (See page 7-18.)

● If your ATV encounters shallow water:

Ride slowly and carefully through slow moving
water, watching for obstacles. Be sure to let wa­ter drain from the ATV and CHECK YOUR
BRAKES FOR PROPER OPERATION when
you come out of the water. Do not continue to
ride your ATV until you have regained adequate
braking ability. (See page 7-19.)

EWB00011

WARNING

Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.

7

7-23

EBU2164A

PERIODIC MAINTENANCE AND ADJUSTMENT

EBU21671

Periodic inspection, adjustment, and lubrication
will keep your vehicle in the safest and most effi­cient condition possible. Safety is an obligation of
the vehicle owner/operator. The most important
points of vehicle inspection, adjustment, and lubri­cation are explained on the following pages.

EWB01841

WARNING

Failure to properly maintain the vehicle or per­forming maintenance activities incorrectly may
increase your risk of injury or death during ser-

8

vice or while using the vehicle. If you are not fa­miliar with vehicle service, have a Yamaha
dealer perform the service.

EWB02561

WARNING

Turn off the engine when performing mainte­nance unless otherwise specified.

● A running engine has moving parts that can

catch on body parts or clothing and electri-

cal parts that can cause shocks or fires.

● Running the engine while servicing can lead

to eye injury, burns, fire, or carbon monoxide
poisoning - possibly leading to death. See
page 2-1 for more information about carbon
monoxide.

The intervals given in the periodic maintenance
and lubrication chart should be considered as a
general guide under normal riding conditions.
However, DEPENDING ON THE WEATHER,
TERRAIN, GEOGRAPHICAL LOCATION, AND
INDIVIDUAL USE, THE MAINTENANCE INTER­VALS MAY NEED TO BE SHORTENED.

EBU27111

Owner’s manual and tool kit

Be sure to put this owner’s manual in the plastic
bag and to always carry it as well as the owner’s
tool kit and the low-pressure tire gauge in their re­spective compartments under the seat.

8-1

1

2

1. Owner’s manual

2. Owner’s tool kit

3. Low-pressure tire gauge

1

2

3

The service information included in this manual
and the tools provided in the owner’s tool kit are in­tended to assist you in the performance of preven­tive maintenance and minor repairs. However,
additional tools such as a torque wrench may be
necessary to perform certain maintenance work
correctly.

TIP

If you do not have the tools or experience required
for a particular job, have a Yamaha dealer perform
it for you.

8

8-2

EBU21743

Periodic maintenance chart for the emission control system

TIP

● For ATVs not equipped with an odometer or an hour meter, follow the month maintenance intervals.

● For ATVs equipped with an odometer or an hour meter, follow the km (mi) or hours maintenance inter-

vals. However, keep in mind that if the ATV isn’t used for a long period of time, the month maintenance

intervals should be followed.

● Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools,

data and technical skills.

INITIAL EVERY

NO. ITEM

CHECK OR MAINTENANCE

JOB

Whichev­er comes

first

8

1 * Fuel line

2 Spark plug

3 * Valves • Check valve clearance and adjust if necessary. √ √√√
4 * Fuel injection • Check and adjust engine idle speed. √√√√√

Crankcase breather

5 *

system

6 * Exhaust system

• Check fuel hoses for cracks or other damage, and
replace if necessary.

• Check condition and clean, regap, or replace if
necessary.

• Check breather hose for cracks or other damage,
and replace if necessary.

• Check for leakage and replace gasket(s) if neces­sary.

• Check for looseness and tighten all screw clamps
and joints if necessary.

month136612

km

(mi)

hours 20 80 160 160 320

320

(200)

1300
(800)

√√√√√

2500

(1600)

2500

(1600)

√√√

√√√

√√√

5000

(3200)

8-3

INITIAL EVERY

NO. ITEM

7 Spark arrester • Clean. √√√

CHECK OR MAINTENANCE

JOB

Whichev­er comes

first

month136612

km

(mi)

hours 20 80 160 160 320

320

(200)

1300
(800)

2500

(1600)

2500

(1600)

5000

(3200)

8

8-4

EBU21864

General maintenance and lubrication chart

INITIAL EVERY

NO. ITEM

1 Air filter element • Clean and replace if necessary.

2 * Clutch • Check operation and adjust if necessary. √ √√√

3 * Front brake

4 * Rear brake

8

5 * Brake hoses

6 * Parking brake • Check operation and adjust if necessary. √√√√√

7 * Wheels

8 * Tires

CHECK OR MAINTENANCE

JOB

• Check operation and correct if necessary.

• Check fluid level and ATV for fluid leakage, and

correct if necessary.

• Replace brake pads. Whenever worn to the limit

• Check operation and correct if necessary.

• Check fluid level and ATV for fluid leakage, and

correct if necessary.

• Replace brake pads. Whenever worn to the limit

• Check for cracks or other damage, and replace if

necessary.

• Replace. Every 4 years

• Check runout and for damage, and replace if nec-

essary.

• Check tread depth and for damage, and replace if
necessary.

• Check air pressure and balance, and correct if
necessary.

Whichev­er comes

first

month136612

km

(mi)

hours 20 80 160 160 320

320

(200)

Every 20–40 hours (more often in wet or

1300
(800)

√√√√√

√√√√√

√ √√√

√ √√√

2500

(1600)

dusty areas)

√√√√

2500

(1600)

5000

(3200)

8-5

INITIAL EVERY

NO. ITEM

9 * Wheel hub bearings

10 * Swingarm pivots

Upper and lower

11 *

arm pivots

12 Drive chain

13 * Chassis fasteners

Shock absorber as-

14 *

semblies
Rear suspension re-

lay arm and con-

15 *

necting arm
pivoting points

16 * Steering shaft • Lubricate with lithium-soap-based grease. √√√

17 * Steering system

18 Engine oil

CHECK OR MAINTENANCE

JOB

• Check for looseness or damage, and replace if
necessary.

• Check operation and for excessive play, and re­place bearings if necessary.

• Lubricate with lithium-soap-based grease.

• Lubricate with lithium-soap-based grease. √√√

• Check chain slack and adjust if necessary.

• Check rear wheel alignment and correct if neces-

sary.

• Clean and lubricate.

• Make sure that all nuts, bolts, and screws are

properly tightened.

• Check operation and correct if necessary.

• Check for oil leakage and replace if necessary.

• Check operation and correct if necessary.

• Lubricate with lithium-soap-based grease.

• Check operation and repair or replace if damaged.

• Check toe-in and adjust if necessary.

• Change.

• Check ATV for oil leakage, and correct if neces-

sary.

Whichev­er comes

first

month136612

km

(mi)

hours 20 80 160 160 320

320

(200)

1300
(800)

√ √√√

√√√√√

√√√√√

√√√√√

√ √√√

2500

2500

(1600)

√√√√

(1600)

√√√

√√√

5000

(3200)

8

8-6

INITIAL EVERY

month136612

km

(mi)

hours 20 80 160 160 320

320

(200)

1300
(800)

√√√√√

√√√√√

√√√√√

2500

(1600)

2500

(1600)

NO. ITEM

Engine oil filter ele-

19

ment

20 Cooling system

Moving parts and

21 *

cables

Throttle lever hous-

22 *

ing and cable

8

EBU23071

Front and rear brake

23 *

switches

24 * Lights and switches

CHECK OR MAINTENANCE

JOB

• Replace. √√√

• Check coolant level and ATV for coolant leakage,

and correct if necessary.

• Replace coolant. Every 2 years

• Lubricate. √√√√

• Check operation and correct if necessary.

• Check throttle cable free play and adjust if neces-

sary.

• Lubricate throttle lever housing and cable.

• Check operation and correct if necessary. √√√√√

• Check operation and correct if necessary.

• Adjust headlight beams.

Whichev­er comes

first

TIP

● Some maintenance items need more frequent service if you are riding in unusually wet, dusty, sandy or

muddy areas, or at full-throttle.

● Hydraulic brake service

• Regularly check and, if necessary, correct the brake fluid level.

5000

(3200)

8-7

• Every two years replace the internal components of the brake master cylinders and calipers, and
change the brake fluid.

• Replace the brake hoses every four years and if cracked or damaged.

8

8-8

EWB00011

WARNING

Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.

EBU23080

Removing and installing the panel

The panel shown needs to be removed to perform
some of the maintenance jobs described in this
chapter. Refer to this section each time the panel
needs to be removed and installed.

8

EBU23101

Panel A

To remove the panel
Remove the bolts, and then take the panel off.

2

2

1

1

1. Panel A

2. Bolt

To install the panel
Place the panel in the original position and install
the bolts.

1. Panel A

EBU23211

Checking the spark plug

The spark plug is an important engine component,
which is easy to check. Since heat and deposits
will cause any spark plug to slowly erode, the spark

8-9

plug should be removed and checked in accor­dance with the periodic maintenance and lubrica­tion chart. In addition, the condition of the spark
plug can reveal the condition of the engine.

To remove the spark plug

1. Remove the spark plug cap.

1

1. Spark plug cap

2. Remove the spark plug as shown, with the
spark plug wrench included in the owner’s tool
kit.

1

1. Spark plug wrench

To check the spark plug

1. Check that the porcelain insulator around the
center electrode of the spark plug is a medi­um-to-light tan (the ideal color when the ATV
is ridden normally).

TIP

If the spark plug shows a distinctly different color,
the engine could be operating improperly. Do not
attempt to diagnose such problems yourself. In­stead, have a Yamaha dealer check the ATV.

8

8-10

2. Check the spark plug for electrode erosion
and excessive carbon or other deposits, and
replace it if necessary.

Specified spark plug:

NGK/CR8E

To install the spark plug

1. Measure the spark plug gap with a wire thick­ness gauge and, if necessary, adjust the gap
to specification.

Spark plug gap:

0.7–0.8 mm (0.028–0.031 in)

8

1. Spark plug gap

2. Clean the surface of the spark plug gasket
and its mating surface, and then wipe off any
grime from the spark plug threads.

3. Install the spark plug with the spark plug
wrench, and then tighten it to the specified
torque.

Tightening torque:

Spark plug:

12.5 Nm (1.25 m·kgf, 9.0 ft·lbf)

8-11

TIP

If a torque wrench is not available when installing
a spark plug, a good estimate of the correct torque
is 1/4–1/2 turn past finger tight. However, the spark
plug should be tightened to the specified torque as
soon as possible.

TIP

To achieve the proper engine oil temperature for
an accurate oil level reading, the engine must have
first completely cooled down, and then warmed up
again for several minutes to normal operating tem­perature.

4. Install the spark plug cap.

EBU26785

Engine oil and oil filter element

The engine oil level should be checked before
each ride. In addition, the oil must be changed and
the oil filter element replaced at the intervals spec­ified in the periodic maintenance and lubrication
chart.

To check the engine oil level

1. Place the ATV on a level surface.

2. Start the engine, warm it up until the engine oil
has reached a normal temperature of 60 °C
(140 °F), let it continue to idle for ten seconds
or more, and then turn the engine off.

3. Remove the engine oil tank filler cap, and then
wipe the engine oil dipstick off with a clean
rag.

4. Insert the dipstick in the filler hole (without
screwing it in), and then remove it again to
check the oil level.

8

8-12

Be sure the engine oil is at the correct lev-

2

2

el, otherwise engine damage may result.

[ECB00851]

TIP

3

When adding oil, be careful not to overfill the en­gine oil tank; the oil level rises faster starting from

4

the half-level-portion on the dipstick.

5

1

1. Engine oil tank

2. Engine oil filler cap

3. Engine oil dipstick

4. Maximum level mark

5. Minimum level mark

8

TIP

The engine oil should be between the minimum
and maximum level marks.

5. If the engine oil is at or below the minimum
level mark, add sufficient oil of the recom­mended type through the engine oil tank filler
hole to raise it to the correct level. NOTICE:

6. Insert the dipstick into the engine oil tank filler
hole, and then tighten the engine oil tank filler
cap. NOTICE: Make sure that the engine oil

tank filler cap is securely tightened; other­wise, oil may seep out when the engine is
running.

[ECB00362]

To change the engine oil (with or without oil fil­ter element replacement)

1. Place the ATV on a level surface.

2. Start the engine, warm it up for several min­utes, and then turn it off.

3. Place an oil pan under the engine to collect
the used oil.

4. Remove the crankcase engine oil filler cap
and the crankcase engine oil drain bolt.

8-13

5. Remove the engine oil tank filler cap and the
engine oil tank drain bolt.

1

1. Crankcase engine oil filler cap

1

1. Crankcase engine oil drain bolt

1

1. Engine oil tank drain bolt

6. Check the washers for damage, and replace if
necessary.

TIP

Skip steps 7–10 if the oil filter element is not being
replaced.

7. Remove the oil filter element cover by remov­ing the bolts, and then remove the oil filter el­ement.

8-14

8

1

1

2

2

2

1. Oil filter element cover

2. Bolt

8. Check the O-rings for damage, and replace
them if necessary.

8

1. Oil filter element

2. O-ring

9. Install a new oil filter element and the O-rings.

TIP

Make sure that the O-rings are properly seated.

10. Install the oil filter element cover by installing
the bolts, and then tighten them to the speci­fied torque.

Tightening torque:

Oil filter element cover bolt:

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

8-15

11. Install the crankcase engine oil drain bolt and
the engine oil tank drain bolt, and then tighten
them to the specified torques.

Tightening torques:

Crankcase engine oil drain bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

Engine oil tank drain bolt:

19 Nm (1.9 m·kgf, 13 ft·lbf)

12. Install the crankcase engine oil filler cap, and
then tighten it to the specified torque.

Tightening torque:

Crankcase engine oil filler cap:

12 Nm (1.2 m·kgf, 8.7 ft·lbf)

13. Pour only 1.3 L (1.37 US qt, 1.14 Imp.qt) of
the specified amount of the recommended en­gine oil through the engine oil tank filler hole,
and then install and tighten the oil tank filler
cap.

14. Start the engine, rev it several times, and then
turn it off.

15. Remove the engine oil tank filler cap, and then
gradually fill the oil tank with the remaining oil
quantity while regularly checking the oil level
on the dipstick.

16. Install and tighten the engine oil tank filler cap.

Recommended oil:

See page 10-1.

Oil quantity:

Without oil filter element replacement:

1.75 L (1.85 US qt, 1.54 Imp.qt)

With oil filter element replacement:

1.85 L (1.96 US qt, 1.63 Imp.qt)

TIP

Be sure to wipe off spilled oil on any parts after the
engine and exhaust system have cooled down.

ECB00300

NOTICE

● In order to prevent clutch slippage (since the

engine oil also lubricates the clutch), do not
mix any chemical additives. Do not use oils
with a diesel specification of “CD” or oils of

8

8-16

a higher quality than specified. In addition,
do not use oils labeled “ENERGY CONSERV­ING II” or higher.

● Make sure that no foreign material enters the

crankcase.

17. Start the engine, and then let it idle for several
minutes while checking it for oil leakage. If oil
is leaking, immediately turn the engine off and
check for the cause.

18. Turn the engine off, and then check the oil lev­el and correct it if necessary.

EBU23470

Coolant

The coolant level should be checked before each

8

ride. In addition, the coolant must be changed at
the intervals specified in the periodic maintenance
and lubrication chart.

EBU27941

To check the coolant level

1. Place the ATV on a level surface.

TIP

The coolant level must be checked on a cold en­gine since the level varies with engine tempera­ture.

2. Check the coolant level in the coolant reser­voir.

TIP

The coolant should be between the minimum and
maximum level marks.

1

2

1. Maximum level mark

2. Minimum level mark

8-17

3. If the coolant is at or below the minimum level
mark, remove the coolant reservoir cap, add
coolant or distilled water to the maximum level
mark, and then install the reservoir cap.

NOTICE: If coolant is not available, use
distilled water or soft tap water instead. Do
not use hard water or salt water since they
are harmful to the engine. If water has
been used instead of coolant, replace it
with coolant as soon as possible, other­wise the cooling system will not be pro­tected against frost and corrosion. If water
has been added to the coolant, have a
Yamaha dealer check the antifreeze con­tent of the coolant as soon as possible,
otherwise the effectiveness of the coolant
will be reduced.

[ECB01011]

Coolant reservoir capacity (up to the maximum
level mark):

0.25 L (0.26 US qt, 0.22 Imp.qt)

TIP

● The radiator fan is automatically switched on or

off according to the coolant temperature in the
radiator.

● If the engine overheats, see page 8-50 for fur-

ther instructions.

EBU23542

To change the coolant

EWB01890

WARNING

Wait for the engine and radiator to cool before
removing the radiator cap. You could be
burned by hot fluid and steam blown out under
pressure. Always place a thick rag over the cap
when opening. Allow any remaining pressure
to escape before completely removing the cap.

1. Place the ATV on a level surface.

2. Remove panel A. (See page 8-9.)

3. Place a container under the engine, and then
remove the coolant drain bolt.

8

8-18

1. Coolant drain bolt

4. Remove the radiator cap.

5. Remove the coolant reservoir cap.

6. Disconnect the hose on the coolant reservoir
side, and then drain the coolant from the cool­ant reservoir.

1

1

2

8

1. Radiator cap

1. Coolant reservoir cap

1

2. Hose

7. After draining the coolant, thoroughly flush the
cooling system with clean tap water.

8. Replace the coolant drain bolt washer if it is
damaged, and then tighten the coolant drain
bolt to the specified torque.

Tightening torque:

Coolant drain bolt:

11 Nm (1.1 m·kgf, 8.0 ft·lbf)

8-19

9. Connect the coolant reservoir hose.

10. Pour the recommended coolant into the reser­voir to the maximum level mark, and then in­stall the reservoir cap. NOTICE: Mix

antifreeze with distilled water only. Howev­er, if distilled water is not available, soft
water may be used for refilling. Do not use
hard water or salt water since they are
harmful to the engine.

[ECB00991]

11. Pour the recommended coolant into the radia­tor until it is full.

13. Remove the radiator cap to check the coolant
level in the radiator. If it is low, add sufficient
coolant until it reaches the top of the radiator,
and then install the radiator cap.

14. Start the engine, and then check for coolant
leakage.

TIP

If any leakage is found, have a Yamaha dealer
check the cooling system.

15. Install the panel.

Antifreeze/water mixture ratio:

1:1

Recommended antifreeze:

High-quality ethylene glycol antifreeze con­taining corrosion inhibitors for aluminum en­gines

Coolant quantity:

Radiator capacity (including all routes):

1.61 L (1.70 US qt, 1.42 Imp.qt)
Coolant reservoir capacity (up to the maxi­mum level mark):

0.25 L (0.26 US qt, 0.22 Imp.qt)

12. Install the radiator cap, start the engine, let it
idle for several minutes, and then turn it off.

EBU26803

Cleaning the air filter element

The air filter element should be cleaned at the in­tervals specified in the periodic maintenance and
lubrication chart. Clean or, if necessary, replace
the air filter element more frequently if you are
riding in unusually wet or dusty areas.

TIP

There is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil­ter case.

8-20

8

1

1. Air filter case check hose

1. Place the ATV on a level surface.

2. Remove the seat. (See page 4-13.)

3. Remove the air filter case cover by unhooking

8

the holders.

2

1

2

1. Air filter case cover

2. Air filter case cover holder

4. Loosen the wing bolt.

5. Remove the air filter element together with the
wing bolt and washer.

8-21