Yamaha V STAR 1100 CLASSIC, V STAR 1100 CUSTOM User Manual

OWNER’S MANUAL

XVS11X(C)

XVS11AWX(C)

XVS11ATX(C)

LIT-11626-21-28

3B8-28199-12

EAU10041

INTRODUCTION

EAU10080

Congratulations on your purchase of the Yamaha XVS11X(C)/XVS11AWX(C)/XVS11ATX(C). This model is the result of
Yamaha’s vast experience in the production of fine sporting, touring, and pacesetting racing machines. It represents the high
degree of craftsmanship and reliability that have made Yamaha a leader in these fields.
This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If you
have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.
The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at
the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the
recommended maintenance schedules and operating instructions contained within this manual.

IMPORTANT MANUAL INFORMATION

Particularly important information is distinguished in this manual by the following notations:

The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!

EAU10131

WARNING

Failure to follow WARNING instructions could result in severe injury or death
motorcycle operator, a bystander or a person inspecting or repairing the motor-

to the

cycle.

CAUTION:

NOTE:

A CAUTION indicates special precautions that must be taken to avoid damage to
the motorcycle.

A NOTE provides key information to make procedures easier or clearer.

NOTE:

● This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle

is subsequently sold.

● Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most

current product information available at the time of printing, there may be minor discrepancies between your motorcycle
and this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.

EWA10010

WARNING

PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLY
AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTOR­CYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES

IMPORTANT MANUAL INFORMATION

AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS
AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY
THE CAPABILITIES AND THE RELIABILITY OF THIS MOTORCYCLE.

*Product and specifications are subject to change without notice.

IMPORTANT MANUAL INFORMATION

AFFIX DEALER

LABEL HERE

XVS11X(C)/XVS11AWX(C)/XVS11ATX(C)

OWNER’S MANUAL

©2007 by Yamaha Motor Corporation, U.S.A.

1st edition, May 2007

All rights reserved.

Any reprinting or unauthorized use

without the written permission of

Yamaha Motor Corporation, U.S.A.

is expressly prohibited.

Printed in Japan.

P/N LIT-11626-21-28

EAU10192

TABLE OF CONTENTS

SAFETY INFORMATION ..................1-1

Location of important labels ...........1-5

DESCRIPTION ..................................2-1

Left view ..........................................2-1

Right view........................................2-3

Controls and instruments ................2-5

INSTRUMENT AND CONTROL

FUNCTIONS.......................................3-1

Main switch/steering lock ................3-1

Indicator and warning lights ............3-2

Speedometer unit ...........................3-3

Handlebar switches ........................3-3

Clutch lever ....................................3-4

Shift pedal (XVS11X) ......................3-5

Shift pedal

(XVS11AWX/XVS11ATX) ............3-5

Brake lever .....................................3-5

Brake pedal ....................................3-6

Fuel tank cap ..................................3-6

Fuel ................................................3-7

Catalytic converter ..........................3-8

Fuel cock ........................................3-8

Starter (choke) lever .......................3-9

Seats (XVS11X) ..............................3-9

Seats (XVS11AWX/XVS11ATX) ...3-11

Helmet holder ...............................3-12

Storage compartment ...................3-13

Adjusting the shock absorber

assembly ...................................3-14

Luggage strap holders ................. 3-16

Sidestand ..................................... 3-16

Ignition circuit cut-off system ....... 3-17

PRE-OPERATION CHECKS ............. 4-1

Pre-operation check list ................. 4-2

OPERATION AND IMPORTANT

RIDING POINTS ................................ 5-1

Starting and warming up a cold

engine ......................................... 5-1

Starting a warm engine .................. 5-2

Shifting ........................................... 5-3

Engine break-in .............................. 5-4

Parking ........................................... 5-5

PERIODIC MAINTENANCE AND

MINOR REPAIR................................. 6-1

PERIODIC MAINTENANCE .......... 6-1

Owner’s tool kit .............................. 6-1

Periodic maintenance chart for the

emission control system ............. 6-3

General maintenance and

lubrication chart .......................... 6-4

Removing and installing the

panel ........................................... 6-8

Checking the spark plugs .............. 6-8

Canister (for California only) ........ 6-10

Engine oil ..................................... 6-10

Final gear oil ................................ 6-12

Cleaning the air filter element ...... 6-13

Carburetors ..................................6-14

Checking the engine idling

speed ........................................6-14

Checking the throttle cable free

play ...........................................6-15

Valve clearance ............................ 6-15

Tires (XVS11X) .............................6-15

Tires (XVS11AWX/XVS11ATX) ....6-18

Spoke wheels (XVS11X)............... 6-20

Cast wheels

(XVS11AWX/XVS11ATX).......... 6-20

Accessories and replacement

parts ..........................................6-21

Adjusting the clutch lever free

play ...........................................6-22

Adjusting the brake lever free

play ...........................................6-22

Adjusting the rear brake light

switch ........................................6-23

Checking the front and rear brake

pads ..........................................6-24

Checking the brake fluid level ......6-24

Changing the brake fluid .............. 6-25

Checking and lubricating the

cables .......................................6-26

Checking and lubricating the

throttle grip and cable ...............6-26

Checking and lubricating the

brake and shift pedals ............... 6-26

Checking and lubricating the

brake and clutch levers .............6-27

TABLE OF CONTENTS

Checking and lubricating the

sidestand ...................................6-27

Lubricating the swingarm pivots ...6-28
Lubricating the rear suspension ...6-28

Checking the front fork .................6-28

Checking the steering ...................6-29

Checking the wheel bearings .......6-30

Battery ..........................................6-30

Replacing the fuses ......................6-31

Replacing the headlight bulb ........6-33

Replacing a turn signal light bulb

or the tail/brake light bulb ..........6-34

Supporting the motorcycle ............6-35

Troubleshooting ............................6-35

Troubleshooting chart ...................6-36

MOTORCYCLE CARE AND

STORAGE ..........................................7-1

Matte color caution .........................7-1

Care ................................................7-1

Storage ...........................................7-3

SPECIFICATIONS .............................8-1

CONSUMER INFORMATION.............9-1

Identification numbers ....................9-1

Reporting safety defects .................9-3

Motorcycle noise regulation ............9-4

Maintenance record ........................9-5

YAMAHA MOTOR CORPORATION,

U.S.A. STREET AND ENDURO
MOTORCYCLE LIMITED

WARRANTY ...............................9-7

YAMAHA EXTENDED SERVICE

(Y.E.S.) ....................................... 9-9

SAFETY INFORMATION

EAU10251

MOTORCYCLES ARE SINGLE
TRACK VEHICLES. THEIR SAFE USE
AND OPERATION ARE DEPENDENT
UPON THE USE OF PROPER RIDING
TECHNIQUES AS WELL AS THE EX­PERTISE OF THE OPERATOR. EV­ERY OPERATOR SHOULD KNOW
THE FOLLOWING REQUIREMENTS
BEFORE RIDING THIS MOTOR­CYCLE.
HE OR SHE SHOULD:

● OBTAIN THOROUGH INSTRUC-

TIONS FROM A COMPETENT
SOURCE ON ALL ASPECTS OF
MOTORCYCLE OPERATION.

● OBSERVE THE WARNINGS AND

MAINTENANCE REQUIRE­MENTS IN THE OWNER’S MAN­UAL.

● OBTAIN QUALIFIED TRAINING

IN SAFE AND PROPER RIDING
TECHNIQUES.

● OBTAIN PROFESSIONAL TECH-

NICAL SERVICE AS INDICATED
BY THE OWNER’S MANUAL

AND/OR WHEN MADE NECES­SARY BY MECHANICAL CONDI­TIONS.

Safe riding

● Always make pre-operation

checks. Careful checks may help
prevent an accident.

● This motorcycle is designed to car-

ry the operator and a passenger.

● The failure of motorists to detect

and recognize motorcycles in traf­fic is the predominating cause of
automobile/motorcycle accidents.
Many accidents have been caused
by an automobile driver who did
not see the motorcycle. Making
yourself conspicuous appears to
be very effective in reducing the
chance of this type of accident.

Therefore:

• Wear a brightly colored jacket.

• Use extra caution when ap-

proaching and passing through
intersections, since intersec­tions are the most likely places
for motorcycle accidents to oc­cur.

• Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.

● Many motorcycle accidents in-

volve inexperienced operators. In
fact, many operators who have
been involved in accidents do not
even have a current motorcycle li­cense.

• Make sure that you are qualified
and that you only lend your
motorcycle to other qualified op­erators.

• Know your skills and limits.
Staying within your limits may
help you to avoid an accident.

• We recommend that you prac­tice riding your motorcycle
where there is no traffic until you
have become thoroughly famil­iar with the motorcycle and all of
its controls.

● Many motorcycle accidents have

been caused by error of the motor­cycle operator. A typical error
made by the operator is veering

1

1-1

SAFETY INFORMATION

wide on a turn due to EXCESSIVE
SPEED or undercornering (insuffi­cient lean angle for the speed).

1

• Always obey the speed limit and
never travel faster than warrant­ed by road and traffic conditions.

• Always signal before turning or
changing lanes. Make sure that
other motorists can see you.

● The posture of the operator and

passenger is important for proper
control.

• The operator should keep both
hands on the handlebar and
both feet on the operator foot­rests during operation to main­tain control of the motorcycle.

• The passenger should always
hold onto the operator, seat
strap, or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.

• Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.

● Never ride under the influence of

alcohol or other drugs.

● This motorcycle is designed for on-

road use only, therefore, it is not
suitable for off-road use.

Protective apparel

The majority of fatalities from motor­cycle accidents are the result of head
injuries. The use of a safety helmet is
the single most critical factor in the pre­vention or reduction of head injuries.

● Always wear an approved helmet.

● Wear a face shield or goggles.

Wind in your unprotected eyes
could contribute to an impairment
of vision which could delay seeing
a hazard.

● The use of a jacket, heavy boots,

trousers, gloves, etc., is effective in
preventing or reducing abrasions
or lacerations.

● Never wear loose-fitting clothes,

otherwise they could catch on the
control levers, footrests, or wheels
and cause injury or an accident.

● Never touch the engine or exhaust

system during or after operation.
They become very hot and can

cause burns. Always wear protec­tive clothing that covers your legs,
ankles, and feet.

● Passengers should also observe

the precautions mentioned above.

Modifications

Modifications made to this motorcycle
not approved by Yamaha, or the re­moval of original equipment, may ren­der the motorcycle unsafe for use and
may cause severe personal injury.
Modifications may also make your
motorcycle illegal to use.

Loading and accessories

Adding accessories or cargo to your
motorcycle can adversely affect stabili­ty and handling if the weight distribution
of the motorcycle is changed. To avoid
the possibility of an accident, use ex­treme caution when adding cargo or
accessories to your motorcycle. Use
extra care when riding a motorcycle
that has added cargo or accessories.
Here are some general guidelines to
follow if loading cargo or adding acces­sories to your motorcycle:

1-2

SAFETY INFORMATION

Loading
The total weight of the operator, pas­senger, accessories and cargo must
not exceed the maximum load limit.

Maximum load:

XVS11ATX 203 kg (448 lb)
XVS11ATXC 200 kg (441 lb)
XVS11AWX 203 kg (448 lb)
XVS11AWXC 200 kg (441 lb)
XVS11X 200 kg (441 lb)
XVS11XC 197 kg (434 lb)

When loading within this weight limit,
keep the following in mind:

● Cargo and accessory weight

should be kept as low and close to
the motorcycle as possible. Make
sure to distribute the weight as
evenly as possible on both sides of
the motorcycle to minimize imbal­ance or instability.

● Shifting weights can create a sud-

den imbalance. Make sure that ac­cessories and cargo are securely
attached to the motorcycle before
riding. Check accessory mounts
and cargo restraints frequently.

● Never attach any large or heavy

items to the handlebar, front fork,
or front fender. These items, in­cluding such cargo as sleeping
bags, duffel bags, or tents, can
create unstable handling or slow

steering response.
Accessories
Genuine Yamaha accessories have
been specifically designed for use on
this motorcycle. Since Yamaha cannot
test all other accessories that may be
available, you must personally be re­sponsible for the proper selection, in­stallation and use of non-Yamaha
accessories. Use extreme caution
when selecting and installing any ac­cessories.
Keep the following guidelines in mind,
as well as those provided under “Load-
ing” when mounting accessories.

● Never install accessories or carry

cargo that would impair the perfor-

mance of your motorcycle. Care-

fully inspect the accessory before

using it to make sure that it does

not in any way reduce ground

clearance or cornering clearance,

limit suspension travel, steering
travel or control operation, or ob­scure lights or reflectors.

• Accessories fitted to the handle­bar or the front fork area can
create instability due to improper
weight distribution or aerody­namic changes. If accessories
are added to the handlebar or
front fork area, they must be as
lightweight as possible and
should be kept to a minimum.

• Bulky or large accessories may
seriously affect the stability of
the motorcycle due to aerody­namic effects. Wind may at­tempt to lift the motorcycle, or
the motorcycle may become un­stable in cross winds. These ac­cessories may also cause
instability when passing or being
passed by large vehicles.

• Certain accessories can dis­place the operator from his or
her normal riding position. This
improper position limits the free­dom of movement of the opera-

1

1-3

SAFETY INFORMATION

tor and may limit control ability,
therefore, such accessories are
not recommended.

1

● Use caution when adding electri-

cal accessories. If electrical acces­sories exceed the capacity of the
motorcycle’s electrical system, an
electric failure could result, which
could cause a dangerous loss of
lights or engine power.

Gasoline and exhaust gas

● GASOLINE IS HIGHLY FLAMMA-

BLE:

• Always turn the engine off when
refueling.

• Take care not to spill any gaso­line on the engine or exhaust
system when refueling.

• Never refuel while smoking or in
the vicinity of an open flame.

● Never start the engine or let it run

for any length of time in a closed
area. The exhaust fumes are poi­sonous and may cause loss of
consciousness and death within a
short time. Always operate your
motorcycle in an area that has ad­equate ventilation.

● Always turn the engine off before

leaving the motorcycle unattended
and remove the key from the main
switch. When parking the motor­cycle, note the following:

• The engine and exhaust system
may be hot, therefore, park the
motorcycle in a place where pe­destrians or children are not like­ly to touch these hot areas.

• Do not park the motorcycle on a
slope or soft ground, otherwise it
may fall over.

• Do not park the motorcycle near
a flammable source (e.g. a kero­sene heater, or near an open
flame), otherwise it could catch
fire.

● When transporting the motorcycle

in another vehicle, make sure that
it is kept upright and that the fuel
cock is turned to “ON” or “RES” (for
vacuum type) / “OFF” (for manual
type). If it should lean over, gaso­line may leak out of the carburetor
or fuel tank.

● If you should swallow any gaso-

line, inhale a lot of gasoline vapor,
or allow gasoline to get into your

1-4

eyes, see your doctor immediately.
If any gasoline spills on your skin
or clothing, immediately wash the
affected area with soap and water
and change your clothes.

Location of important labels

Please read the following important labels carefully before operating this vehicle.

SAFETY INFORMATION

EAU10381

1

1-5

SAFETY INFORMATION

1

1

2

4 California only

3 XVS11X

3 XVS11AWX / XVS11ATX

1-6

Left view

XVS11X

DESCRIPTION

EAU32220

2

1. Shift pedal (page 3-5)

2. Fuel cock (page 3-8)

3. Headlight (page 6-33)

4. Shock absorber assembly spring preload adjusting ring (page 3-14)

5. Helmet holder (page 3-12)

6. Rear turn signal light (page 6-34)

7. Tail/brake light (page 6-34)

8. Storage compartment (page 3-13)

9. Owner’s tool kit (page 6-1)

10.Fuse box (page 6-31)

11.Engine oil level check window (page 6-10)

2-1

DESCRIPTION

XVS11AWX/XVS11ATX

2

1. Shift pedal (page 3-5)

2. Fuel cock (page 3-8)

3. Headlight (page 6-33)

4. Shock absorber assembly spring preload adjusting ring (page 3-14)

5. Helmet holder (page 3-12)

6. Rear turn signal light (page 6-34)

7. Tail/brake light (page 6-34)

8. Storage compartment (page 3-13)

9. Owner’s tool kit (page 6-1)

10.Fuse box (page 6-31)

11.Engine oil level check window (page 6-10)

2-2

Right view

XVS11X

DESCRIPTION

EAU32230

2

1. Muffler

2. Battery (page 6-30)

3. Main fuse (page 6-31)

4. Fuel tank (page 3-6)

5. Front turn signal/position lights (page 6-34)

6. Main switch/steering lock (page 3-1)

7. Air filter element (page 6-13)

8. Rear brake light switch (page 6-23)

9. Brake pedal (page 3-6)

2-3

DESCRIPTION

XVS11AWX/XVS11ATX

2

1. Muffler

2. Battery (page 6-30)

3. Main fuse (page 6-31)

4. Fuel tank (page 3-6)

5. Front turn signal/position lights (page 6-34)

6. Main switch/steering lock (page 3-1)

7. Air filter element (page 6-13)

8. Rear brake light switch (page 6-23)

9. Brake pedal (page 3-6)

2-4

Controls and instruments

1. Clutch lever (page 3-4)

2. Left handlebar switches (page 3-3)

3. Starter (choke) lever (page 3-9)

4. Speedometer unit (page 3-3)

5. Fuel tank cap (page 3-6)

6. Right handlebar switches (page 3-3)

7. Throttle grip (page 6-15)

8. Brake lever (page 3-5)

DESCRIPTION

EAU10430

2

2-5

INSTRUMENT AND CONTROL FUNCTIONS

Main switch/steering lock

3

The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.

ON

All electrical systems are supplied with
power, and the headlight, meter light­ing, taillight and position lights come
on, and the engine can be started. The
key cannot be removed.

OFF

All electrical systems are off. The key
can be removed.

EAU10460

EAU10510

EAU10660

LOCK

EAU10680

The steering is locked, and all electrical
systems are off. The key can be re­moved.

To lock the steering

1. Push.

2. Turn.

1. Turn the handlebars all the way to
the left.

2. Push the key in from the “OFF” po­sition, and then turn it to “LOCK”
while still pushing it.

3. Remove the key.

To unlock the steering

1. Push.

2. Turn.

Push the key in, and then turn it to
“OFF” while still pushing it.

EWA10060

WARNING

Never turn the key to “OFF” or
“LOCK” while the vehicle is moving,
otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident. Make
sure that the vehicle is stopped be­fore turning the key to “OFF” or
“LOCK”.

3-1

INSTRUMENT AND CONTROL FUNCTIONS

EAU11003

Indicator and warning lights

1. Oil level warning light “”

2. Neutral indicator light “”

3. Turn signal indicator light “”

4. Engine trouble warning light “”

5. High beam indicator light “”

EAU11020

Turn signal indicator light “”

This indicator light flashes when the
turn signal switch is pushed to the left or
right.

EAU11060

Neutral indicator light “”

This indicator light comes on when the
transmission is in the neutral position.

High beam indicator light “”

EAU11080

This indicator light comes on when the
high beam of the headlight is switched
on.

EAU11120

Oil level warning light “”

This warning light comes on when the
engine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical cir­cuit.

NOTE:

Even if the oil level is sufficient, the
warning light may flicker when riding on
a slope or during sudden acceleration
or deceleration, but this is not a mal­function.

Engine trouble warning light “”

EAU11500

This warning light comes on or flashes
when an electrical circuit monitoring the
engine is defective. When this occurs,
have a Yamaha dealer check the self­diagnosis system.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. If the warning light does not come
on for a few seconds, then go off, have
a Yamaha dealer check the electrical
circuit.

3

3-2

INSTRUMENT AND CONTROL FUNCTIONS

Speedometer unit

3

1. “TRIP” button

2. Odometer/tripmeter

The speedometer unit is equipped with
a digital odometer and a tripmeter. The
speedometer shows riding speed. The
odometer shows the total distance trav­eled. The tripmeter shows the distance
traveled since it was last set to zero.
Pushing the “TRIP” button switches the
display between the odometer mode
“ODO” and the tripmeter mode “TRIP”.
To reset the tripmeter, select it by push­ing the “TRIP” button, and then push
the “TRIP” button again and hold it
down for at least one second. The trip­meter can be used to estimate the dis-

EAU11731

tance that can be traveled with a full
tank of fuel. This information will enable
you to plan future fuel stops.

NOTE:

This model is not equipped with a ta­chometer; however, it has a built-in
speed limiter, which prevents the en­gine speed from exceeding approxi­mately 6800 r/min and the vehicle
speed from exceeding approximately
175 km/h (110 mi/h).

EAU12347

Handlebar switches

Left

1. Dimmer switch “ / ”

2. Horn switch “”

3. Turn signal switch “ / ”

Right

1. Engine stop switch “ / ”

2. Start switch “”

3-3

INSTRUMENT AND CONTROL FUNCTIONS

Dimmer switch “ / ”

EAU12400

Set this switch to “” for the high
beam and to “” for the low beam.

EAU12430

Turn signal switch “ / ”

To signal a right-hand turn, push this
switch to “”. To signal a left-hand
turn, push this switch to “”. When re-
leased, the switch returns to the center
position.
Since this model is equipped with a
self-canceling system, the turn signal
lights will self-cancel after the vehicle
has traveled both about 150 m (490 ft)
and for approximately 15 seconds.
However, the turn signal lights can also
be canceled manually by pushing the
switch in after it has returned to the cen­ter position.

NOTE:

The self-canceling system only oper­ates when the vehicle is moving, so that
the turn signal lights will not self-cancel
while you are stopped at an intersec­tion.

Horn switch “”

EAU12500

Press this switch to sound the horn.

EAU12660

Engine stop switch “ / ”

Set this switch to “” before starting
the engine. Set this switch to “” to
stop the engine in case of an emergen­cy, such as when the vehicle overturns
or when the throttle cable is stuck.

EAU12710

Start switch “”

Push this switch to crank the engine
with the starter.

ECA10050

CAUTION:

See page 5-1 for starting instruc­tions prior to starting the engine.

EAU12820

Clutch lever

3

1. Clutch lever

The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handle­bar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch switch, which is part of the igni­tion circuit cut-off system. (See page
3-17.)

3-4

INSTRUMENT AND CONTROL FUNCTIONS

Shift pedal (XVS11X)

3

1. Shift pedal

The shift pedal is located on the left
side of the engine and is used in com­bination with the clutch lever when
shifting the gears of the 5-speed con­stant-mesh transmission equipped on
this motorcycle.

EAU12870

EAU12880

Shift pedal
(XVS11AWX/XVS11ATX)

1. Shift pedal

The shift pedal is located on the left
side of the engine and is used in com­bination with the clutch lever when
shifting the gears of the 5-speed con­stant-mesh transmission equipped on
this motorcycle.

NOTE:

Use your toes or heel to shift up and
your toes to shift down.

EAU12890

Brake lever

1. Brake lever

The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handle­bar grip.

3-5

INSTRUMENT AND CONTROL FUNCTIONS

EAU12941

Brake pedal

XVS11X

1. Brake pedal

XVS11AWX/XVS11ATX

1. Brake pedal

The brake pedal is on the right side of
the motorcycle. To apply the rear
brake, press down on the brake pedal.

EAU13120

Fuel tank cap

1. Fuel tank cap lock cover

2. “” mark

3. Unlock.

4. Lock.

To remove the fuel tank cap

Slide the lock cover open, insert the key
into the lock, and then turn it 1/4 turn
clockwise. The lock will be released
and the fuel tank cap can be removed.

To install the fuel tank cap

1. Insert the fuel tank cap into the
tank opening with the key inserted
in the lock and with the “” mark
facing forward.

2. Turn the key counterclockwise to
the original position, remove it, and
then close the lock cover.

NOTE:

The fuel tank cap cannot be installed
unless the key is in the lock. In addition,
the key cannot be removed if the cap is
not properly installed and locked.

EWA10130

WARNING

Make sure that the fuel tank cap is
properly installed before riding.

3

3-6

INSTRUMENT AND CONTROL FUNCTIONS

Fuel

3

1. Fuel tank filler tube

2. Fuel level

Make sure that there is sufficient fuel in
the tank. Fill the fuel tank to the bottom
of the filler tube as shown.

WARNING

● Do not overfill the fuel tank, oth-

erwise it may overflow when the
fuel warms up and expands.

● Avoid spilling fuel on the hot en-

gine.

EAU13211

EWA10880

ECA10070

CAUTION:

Immediately wipe off spilled fuel
with a clean, dry, soft cloth, since
fuel may deteriorate painted surfac­es or plastic parts.

EAU13300

Recommended fuel:

UNLEADED GASOLINE ONLY

Fuel tank capacity:

17.0 L (4.49 US gal) (3.74 Imp.gal)

Fuel reserve amount:

4.5 L (1.19 US gal) (0.99 Imp.gal)

ECA11400

CAUTION:

Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
as well as to the exhaust system.

Your Yamaha engine has been de­signed to use regular unleaded gaso­line with a pump octane number
[(R+M)/2] of 86 or higher, or a research
octane number of 91 or higher. If

knocking (or pinging) occurs, use a
gasoline of a different brand or premi­um unleaded fuel. Use of unleaded fuel
will extend spark plug life and reduce
maintenance costs.

Gasohol

There are two types of gasohol: gaso­hol containing ethanol and that contain­ing methanol. Gasohol containing
ethanol can be used if the ethanol con­tent does not exceed 10%. Gasohol
containing methanol is not recom­mended by Yamaha because it can
cause damage to the fuel system or ve­hicle performance problems.

3-7

INSTRUMENT AND CONTROL FUNCTIONS

EAU13441

Catalytic converter

This vehicle is equipped with catalytic
converters in the exhaust system.

EWA10860

WARNING

The exhaust system is hot after op­eration. Make sure that the exhaust
system has cooled down before do­ing any maintenance work.

ECA10700

CAUTION:

The following precautions must be
observed to prevent a fire hazard or
other damages.

● Use only unleaded gasoline.

The use of leaded gasoline will
cause unrepairable damage to
the catalytic converter.

● Never park the vehicle near pos-

sible fire hazards such as grass
or other materials that easily
burn.

● Do not allow the engine to idle

too long.

EAU13550

Fuel cock

The fuel cock supplies fuel from the
tank to the carburetors while also filter­ing it.
The fuel cock lever positions are ex­plained as follows and shown in the il­lustrations.

OFF

1. Pointed end positioned over “OFF”

With the fuel cock lever in this position,
fuel will not flow. Always turn the fuel
cock lever to this position when the en­gine is not running.

ON

3

1. Pointed end positioned over “ON”

With the fuel cock lever in this position,
fuel flows to the carburetors. Turn the
fuel cock lever to this position when
starting the engine and riding.

RES

3-8

1. Pointed end positioned over “RES”

INSTRUMENT AND CONTROL FUNCTIONS

This indicates reserve. With the fuel
cock lever in this position, the fuel re­serve is made available. Turn the fuel
cock lever to this position if you run out
of fuel while riding. When this occurs,
refuel as soon as possible and be sure
to turn the fuel cock lever back to “ON”!

3

EAU13610

Starter (choke) lever “”

1. Starter (choke) lever “”

Starting a cold engine requires a richer
air-fuel mixture, which is supplied by
the starter (choke).
Move the lever in direction (a) to turn on
the starter (choke).
Move the lever in direction (b) to turn off
the starter (choke).

ECA10990

CAUTION:

Do not use the starter (choke) for
more than 3 minutes as the exhaust
pipe may discolor from excessive
heat. In addition, extended use of
the starter (choke) will cause after­burning. If this occurs, turn off the
starter (choke).

EAU14213

Seats (XVS11X)

Passenger seat

To remove the passenger seat
Remove the nut and washer, and then
pull the passenger seat up.

1. Nut

2. Washer

To install the passenger seat

1. Insert the projection on the front of
the passenger seat into the seat
holder as shown and place the
seat in the original position.

2. Install the washer and nut, and
then tighten the nut to the specified
torque.

3-9

INSTRUMENT AND CONTROL FUNCTIONS

Tightening torque:

Passenger seat nut:

13 Nm (1.3 m·kgf, 9.4 ft·lbf)

1. Projection

2. Seat holder

Rider seat

To remove the rider seat

1. Remove the passenger seat.

2. Remove the bolts and passenger
seat holder, and then pull the rider
seat up.

2. Install the passenger seat holder
and bolts.

3. Install the passenger seat.

NOTE:

Make sure that the seats are properly
secured before riding.

3

1. Bolt

2. Passenger seat holder

To install the rider seat

1. Insert the projections on the front
of the rider seat into the seat hold­ers as shown, and then place the
seat in the original position.

1. Projection

2. Seat holder

3-10

INSTRUMENT AND CONTROL FUNCTIONS

Seats
(XVS11AWX/XVS11ATX)

Passenger seat

To remove the passenger seat
Remove the nut and washer, and then

3

pull the passenger seat up.

1. Nut

2. Washer

To install the passenger seat

1. Insert the projection on the front of
the passenger seat into the holder
as shown and place the seat in the
original position.

2. Install the washer and nut, and
then tighten the nut to the specified
torque.

EAU14201

Tightening torque:

Passenger seat nut:

13 Nm (1.3 m·kgf, 9.4 ft·lbf)

1. Projection

2. Seat holder

Rider seat

To remove the rider seat

1. Remove the passenger seat.

2. Remove the bolt, and then pull the
rider seat up.

3-11

1. Bolt

To install the rider seat

1. Insert the projections on the front
of the rider seat into the holders as
shown, place the seat in the origi­nal position, and then install the
bolt.

1. Projection

2. Seat holder

INSTRUMENT AND CONTROL FUNCTIONS

2. Install the passenger seat.

NOTE:

Make sure that the seats are properly
secured before riding.

Helmet holder

XVS11X

1. Helmet holder

2. Unlock.

XVS11AWX/XVS11ATX

2

EAU14281

To open the helmet holder, insert the
key into the lock, and then turn the key
as shown.
To lock the helmet holder, place it in the
original position, and then remove the
key.

EWA10160

WARNING

Never ride with a helmet attached to

3

the helmet holder, since the helmet
may hit objects, causing loss of con­trol and possibly an accident.

1

1. Helmet holder

2. Unlock.

3-12

INSTRUMENT AND CONTROL FUNCTIONS

EAU14481

Storage compartment

The storage compartment is located on
the left side of the vehicle.

To open the storage compartment

1. Slide the lock cover open, insert
the key into the lock, and then turn

3

it clockwise.

1. Storage compartment cover

2. Storage compartment lock cover

1. Storage compartment lock

2. Pull the storage compartment cov­er out as shown.

1. Storage compartment cover

To close the storage compartment

1. Place the storage compartment
cover in its original position as
shown.

3-13

1. Storage compartment cover

2. Turn the key counterclockwise, re­move it, and then close the lock
cover.

INSTRUMENT AND CONTROL FUNCTIONS

EAU14871

Adjusting the shock absorber
assembly

The shock absorber assembly is locat­ed under the rider seat and is equipped
with a spring preload adjusting ring.

ECA10100

CAUTION:

Never attempt to turn an adjusting
mechanism beyond the maximum or
minimum settings.

Adjust the spring preload as follows.

1. Remove the rider seat. (See page
3-9.)

2. Remove each quick fastener from
the ignitor unit panel by pushing
the center in with a screwdriver,
then pulling the fastener out.

1. Quick fastener

3. Pull the ignitor unit panel out to the
right.

1. Ignitor unit panel

4. Remove the mudguard by remov­ing each quick fastener.

XVS11X

1. Quick fastener

2. Mudguard

XVS11AWX/XVS11ATX

1

3

2

1. Quick fastener

2. Mudguard

5. To increase the spring preload and
thereby harden the suspension,
turn the adjusting ring in direction
(a). To decrease the spring pre­load and thereby soften the sus­pension, turn the adjusting ring in
direction (b).

NOTE:

● Align the appropriate notch in the

adjusting ring with the position in­dicator on the shock absorber.

● Use the special wrench included in

the owner’s tool kit to make the ad­justment.

3-14

INSTRUMENT AND CONTROL FUNCTIONS

XVS11X

3

1. Spring preload adjusting ring

2. Position indicator

3. Special wrench

XVS11AWX/XVS11ATX

1. Position indicator

2. Spring preload adjusting ring

3. Special wrench

Spring preload setting:

Minimum (soft):

1

Standard:

XVS11X 3
XVS11AWX 4
XVS11ATX 4

Maximum (hard):

XVS11X 7
XVS11AWX 9
XVS11ATX 9

6. Install the mudguard and ignitor
unit panel by installing the quick
fasteners.

NOTE:

To install a quick fastener, push the pin
back so that it will protrude from the fas­tener head, and then insert the fastener
and push the protruding pin in until it is
flush with the fastener head.

1. Quick fastener (after removal)

2. Quick fastener (before installation)

7. Install the rider seat.

EWA10220

WARNING

This shock absorber contains highly
pressurized nitrogen gas. For prop­er handling, read and understand
the following information before
handling the shock absorber. The
manufacturer cannot be held re­sponsible for property damage or
personal injury that may result from
improper handling.

● Do not tamper with or attempt to

open the gas cylinder.

3-15

INSTRUMENT AND CONTROL FUNCTIONS

● Do not subject the shock ab-

sorber to an open flame or other
high heat sources, otherwise it
may explode due to excessive
gas pressure.

● Do not deform or damage the

gas cylinder in any way, as this
will result in poor damping per­formance.

● Always have a Yamaha dealer

service the shock absorber.

EAU15150

Luggage strap holders

1. Luggage strap holder

There is a luggage strap holder on each
passenger footrest.

EAU15301

Sidestand

The sidestand is located on the left side
of the frame. Raise the sidestand or
lower it with your foot while holding the
vehicle upright.

NOTE:

The built-in sidestand switch is part of
the ignition circuit cut-off system, which
cuts the ignition in certain situations.
(See further down for an explanation of
the ignition circuit cut-off system.)

EWA10240

WARNING

The vehicle must not be ridden with
the sidestand down, or if the side­stand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the respon­sibility of raising the sidestand be­fore starting off. Therefore, check
this system regularly as described

3

3-16

INSTRUMENT AND CONTROL FUNCTIONS

below and have a Yamaha dealer re­pair it if it does not function proper­ly.

3

EAU15312

Ignition circuit cut-off system

The ignition circuit cut-off system (com­prising the sidestand switch, clutch
switch and neutral switch) has the fol­lowing functions.

● It prevents starting when the trans-

mission is in gear and the side­stand is up, but the clutch lever is
not pulled.

● It prevents starting when the trans-

mission is in gear and the clutch le­ver is pulled, but the sidestand is
still down.

● It cuts the running engine when the

transmission is in gear and the sid­estand is moved down.

Periodically check the operation of the
ignition circuit cut-off system according
to the following procedure.

EWA10250

WARNING

If a malfunction is noted, have a
Yamaha dealer check the system be­fore riding.

3-17

INSTRUMENT AND CONTROL FUNCTIONS

With the engine turned off:

1. Move the sidestand down.

2. Make sure that the engine stop switch is turned on.

3. Turn the key on.

4. Shift the transmission into the neutral position.

5. Push the start switch.

Does the engine start?

YES NO

With the engine still running:

6. Move the sidestand up.

7. Keep the clutch lever pulled.

8. Shift the transmission into gear.

9. Move the sidestand down.

Does the engine stall?

YES NO

After the engine has stalled:

10. Move the sidestand up.

11. Keep the clutch lever pulled.

12. Push the start switch.

Does the engine start?

YES NO

The system is OK. The motorcycle can be ridden.

NOTE:

This check is most reliable if performed with
a warmed-up engine.

The neutral switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.

The sidestand switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.

The clutch switch may be defective.
The motorcycle should not be ridden until
checked by a Yamaha dealer.

3

3-18

PRE-OPERATION CHECKS

The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly,
even if the vehicle remains unused (for example, as a result of exposure to the elements). Any damage, fluid leakage or loss
of tire air pressure could have serious consequences. Therefore, it is very important, in addition to a thorough visual inspec­tion, to check the following points before each ride.

NOTE:

Pre-operation checks should be made each time the vehicle is used. Such an inspection can be accomplished in a very short
time; and the added safety it assures is more than worth the time involved.

4

WARNING

If any item in the Pre-operation check list is not working properly, have it inspected and repaired before operating
the vehicle.

EAU15593

EWA11150

4-1

PRE-OPERATION CHECKS

Pre-operation check list

ITEM CHECKS PAGE

Fuel

Engine oil

Final gear oil • Check vehicle for oil leakage. 6-12

Front brake

Rear brake

Clutch

• Check fuel level in fuel tank.

• Refuel if necessary.

• Check fuel line for leakage.

• Check oil level in engine.

• If necessary, add recommended oil to specified level.

• Check vehicle for oil leakage.

• Check operation.

• If soft or spongy, have Yamaha dealer bleed hydraulic system.

• Check lever free play.

• Adjust if necessary.

• Check brake pads for wear.

• Replace if necessary.

• Check fluid level in reservoir.

• If necessary, add recommended brake fluid to specified level.

• Check hydraulic system for leakage.

• Check operation.

• If soft or spongy, have Yamaha dealer bleed hydraulic system.

• Check brake pads for wear.

• Replace if necessary.

• Check fluid level in reservoir.

• If necessary, add recommended brake fluid to specified level.

• Check hydraulic system for leakage.

• Check operation.

• Lubricate cable if necessary.

• Check lever free play.

• Adjust if necessary.

6-10

6-22, 6-24, 6-24

6-24, 6-24

6-22

EAU15605

3-7

4

4-2

PRE-OPERATION CHECKS

ITEM CHECKS PAGE

• Make sure that operation is smooth.

Throttle grip

Control cables

Wheels and tires

4

Brake and shift pedals

Brake and clutch levers

Sidestand

Chassis fasteners

Instruments, lights, signals
and switches

Sidestand switch

• Check cable free play.

• If necessary, have Yamaha dealer adjust cable free play and lubricate cable and

grip housing.

• Make sure that operation is smooth.

• Lubricate if necessary.

• Check for damage.

• Check tire condition and tread depth.

• Check air pressure.

• Correct if necessary.

• Make sure that operation is smooth.

• Lubricate pedal pivoting points if necessary.

• Make sure that operation is smooth.

• Lubricate lever pivoting points if necessary.

• Make sure that operation is smooth.

• Lubricate pivot if necessary.

• Make sure that all nuts, bolts and screws are properly tightened.

• Tighten if necessary.

• Check operation.

• Correct if necessary.

• Check operation of ignition circuit cut-off system.

• If system is defective, have Yamaha dealer check vehicle.

6-15, 6-26

6-26

6-15, 6-20

6-26

6-27

6-27

—

—

3-16

4-3

OPERATION AND IMPORTANT RIDING POINTS

EAU15950

EWA10270

WARNING

● Become thoroughly familiar

with all operating controls and
their functions before riding.
Consult a Yamaha dealer re­garding any control or function
that you do not thoroughly un­derstand.

● Never start the engine or oper-

ate it in a closed area for any
length of time. Exhaust fumes
are poisonous, and inhaling
them can cause loss of con­sciousness and death within a
short time. Always make sure
that there is adequate ventila­tion.

● Before starting out, make sure

that the sidestand is up. If the
sidestand is not raised com­pletely, it could contact the
ground and distract the opera­tor, resulting in a possible loss
of control.

EAU16420

Starting and warming up a
cold engine

In order for the ignition circuit cut-off
system to enable starting, one of the
following conditions must be met:

● The transmission is in the neutral

position.

● The transmission is in gear with

the clutch lever pulled and the sid­estand up.

EWA10290

WARNING

● Before starting the engine,

check the function of the igni­tion circuit cut-off system ac­cording to the procedure
described on page 3-17.

● Never ride with the sidestand

down.

1. Turn the fuel cock lever to “ON”.

2. Turn the key to “ON” and make
sure that the engine stop switch is
set to “”.

3. Shift the transmission into the neu­tral position.

5-1

NOTE:

When the transmission is in the neutral
position, the neutral indicator light
should be on, otherwise have a
Yamaha dealer check the electrical cir­cuit.

4. Turn the starter (choke) on and
completely close the throttle. (See
page 3-9.)

5. Start the engine by pushing the
start switch.

NOTE:

If the engine fails to start, release the
start switch, wait a few seconds, and
then try again. Each starting attempt
should be as short as possible to pre­serve the battery. Do not crank the en­gine more than 10 seconds on any one
attempt.

ECA11390

CAUTION:

● The oil level warning light

should come on when the key is
turned to “ON”, and then go off
after two to three seconds. If the
oil level warning light flickers or
remains on after starting, imme-

5

OPERATION AND IMPORTANT RIDING POINTS

diately stop the engine, and
then check the engine oil level
and the vehicle for oil leakage. If
necessary, add engine oil, and
then check the warning light
again. If the warning light does
not come on when turning the
key to “ON”, or if it does not go
off after starting the engine with
sufficient engine oil, have a
Yamaha dealer check the elec­trical circuit.

● The engine trouble warning

5

light should also come on when
the key is turned to “ON”. If the
warning light does not come on
when the key is turned to “ON”,
flashes or remains on after
starting the engine, have a
Yamaha dealer check the elec­trical circuit.

6. After starting the engine, move the
starter (choke) back halfway.

ECA11130

CAUTION:

For maximum engine life, always
warm the engine up before starting
off. Never accelerate hard when the
engine is cold!

7. When the engine is warm, turn the
starter (choke) off.

NOTE:

The engine is warm when it responds
normally to the throttle with the starter
(choke) turned off. To avoid the possi­bility of excessive exhaust emissions,
never leave the starter (choke) on long­er than necessary. The time necessary
for starter (choke) use depends upon
the ambient temperature. Tempera­tures above 10 °C (50 °F) require about
7 seconds of starter (choke) use and
temperatures below 10 °C (50 °F) re­quire about 35 seconds with the starter
(choke) turned on, then about 2.5 min­utes with the starter (choke) in the half­way position.

EAU16640

Starting a warm engine

Follow the same procedure as for start­ing a cold engine with the exception
that the starter (choke) is not required
when the engine is warm.

5-2

OPERATION AND IMPORTANT RIDING POINTS

Shifting

XVS11X

1. Shift pedal

2. Neutral position

XVS11AWX/XVS11ATX

1. Shift pedal

2. Neutral position

EAU16671

Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
The gear positions are shown in the il­lustration.

NOTE:

To shift the transmission into the neu­tral position, press the shift pedal down
repeatedly until it reaches the end of its
travel, and then slightly raise it.

ECA10260

CAUTION:

● Even with the transmission in

the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis­tances. The transmission is
properly lubricated only when
the engine is running. Inade­quate lubrication may damage
the transmission.

● Always use the clutch while

changing gears to avoid damag­ing the engine, transmission,

and drive train, which are not
designed to withstand the
shock of forced shifting.

EAU16680

To start out and accelerate

1. Pull the clutch lever to disengage
the clutch.

2. Shift the transmission into first
gear. The neutral indicator light
should go out.

3. Open the throttle gradually, and at
the same time, release the clutch
lever slowly.

4. At the recommended shift points
shown in the following table, close
the throttle, and at the same time,
quickly pull the clutch lever in.

5. Shift the transmission into second
gear. (Make sure not to shift the
transmission into the neutral posi­tion.)

6. Open the throttle part way and
gradually release the clutch lever.

7. Follow the same procedure when
shifting to the next higher gear.

5

5-3

OPERATION AND IMPORTANT RIDING POINTS

NOTE:

Always shift gears at the recommended
shift points.

To decelerate

1. Apply both the front and the rear
brakes to slow the motorcycle.

2. Shift the transmission into first
gear when the motorcycle reaches
25 km/h (15.5 mi/h). If the engine is
about to stall or runs very roughly,

5

pull the clutch lever in and use the
brakes to stop the motorcycle.

3. Shift the transmission into the neu­tral position when the motorcycle
is almost completely stopped. The
neutral indicator light should come
on.

Recommended shift points

The recommended shift points during
acceleration and deceleration are
shown in the table below.

EAU16700

EAU16720

Shift up points:

1st → 2nd: 20 km/h (12.4 mi/h)
2nd → 3rd: 30 km/h (18.6 mi/h)
3rd → 4th: 40 km/h (24.9 mi/h)
4th → 5th: 50 km/h (31.1 mi/h)

Shift down points:

5th → 4th: 25 km/h (15.5 mi/h)
4th → 3rd: 25 km/h (15.5 mi/h)
3rd → 2nd: 25 km/h (15.5 mi/h)
2nd → 1st: 25 km/h (15.5 mi/h)

EAU16841

Engine break-in

There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the follow­ing material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throt­tle operation or any condition that might
result in engine overheating must be
avoided.

EAU17041

0–1000 km (0–600 mi)

Avoid prolonged operation above 1/3
throttle.

1000–1600 km (600–1000 mi)

Avoid prolonged operation above 1/2
throttle.

5-4

OPERATION AND IMPORTANT RIDING POINTS

ECA10331

CAUTION:

After 1000 km (600 mi) of operation,
the engine oil and final gear oil must
be changed, and the oil filter car­tridge or element replaced.

1600 km (1000 mi) and beyond

The vehicle can now be operated nor­mally.

ECA10270

CAUTION:

If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.

EAU17180

Parking

When parking, stop the engine, remove
the key from the main switch, and then
turn the fuel cock lever to “OFF”.

EWA10310

WARNING

● Since the engine and exhaust

system can become very hot,
park in a place where pedestri­ans or children are not likely to
touch them.

● Do not park on a slope or on soft

ground, otherwise the vehicle
may overturn.

ECA10380

CAUTION:

Never park in an area where there
are fire hazards such as grass or
other flammable materials.

5

5-5

PERIODIC MAINTENANCE AND MINOR REPAIR

Safety is an obligation of the owner. Pe­riodic inspection, adjustment and lubri­cation will keep your vehicle in the
safest and most efficient condition pos­sible. The most important points of
motorcycle inspection, adjustment, and
lubrication are explained on the follow­ing pages.

Maintenance, replacement, or repair
of the emission control devices and
systems may be performed by any
repair establishment or individual
that is certified (if applicable).

6

WARNING

If you are not familiar with mainte­nance work, have a Yamaha dealer
do it for you.

EAU17231

EWA10320

EAU17301

PERIODIC MAINTENANCE

PROPER PERIODIC MAINTENANCE
OF YOUR VEHICLE IS IMPORTANT
IN ORDER TO ENJOY LONG, PLEA­SURABLE SERVICE. ESPECIALLY
IMPORTANT ARE THE MAINTE­NANCE SERVICES RELATED TO
EMISSIONS CONTROL. THESE
CONTROLS NOT ONLY FUNCTION
TO ENSURE CLEANER AIR, BUT
ARE ALSO VITAL TO PROPER EN­GINE OPERATION AND MAXIMUM
PERFORMANCE. IN THE FOLLOW­ING PERIODIC MAINTENANCE
CHARTS, THE SERVICES RELATED
TO EMISSIONS CONTROL ARE
GROUPED SEPARATELY. THESE
SERVICES REQUIRE SPECIALIZED
DATA, KNOWLEDGE, AND EQUIP­MENT. YAMAHA DEALERS ARE
TRAINED AND EQUIPPED TO PER­FORM THESE PARTICULAR SER­VICES.

EAU17440

Owner’s tool kit

1. Owner’s tool kit

The owner’s tool kit is located inside the
storage compartment. (See page
3-13.)
The service information included in this
manual and the tools provided in the
owner’s tool kit are intended to assist
you in the performance of preventive
maintenance and minor repairs. How­ever, additional tools such as a torque
wrench may be necessary to perform
certain maintenance work correctly.

NOTE:

If you do not have the tools or experi­ence required for a particular job, have
a Yamaha dealer perform it for you.

6-1

EWA10340

WARNING

Modifications not approved by
Yamaha may cause loss of perfor­mance, excessive emissions, and
render the vehicle unsafe for use.
Consult a Yamaha dealer before at­tempting any changes.

PERIODIC MAINTENANCE AND MINOR REPAIR

6

6-2

PERIODIC MAINTENANCE AND MINOR REPAIR

Periodic maintenance chart for the emission control system

INITIAL ODOMETER READINGS

No. ITEM ROUTINE

1 * Fuel line

2 * Fuel filter • Replace. Replace.

3 Spark plugs

4 * Valve clearance

6

Crankcase breather

5 *

system

Carburetor synchro-

6 *

nization

7 * Idle speed

8 * Exhaust system

Evaporative emis-

9 *

sion control system
(For California only)

* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.

• Check fuel hoses for cracks or
damage.

• Replace if necessary.

• Check condition.

• Adjust gap and clean.

• Replace every 8000 mi (13000

km) or 12 months.

• Check and adjust valve clearance
when engine is cold.

• Check breather hose for cracks or
damage.

• Replace if necessary.

• Adjust synchronization of carbu-

retors.

• Check and adjust engine idle
speed.

• Check for leakage.

• Tighten if necessary.

• Replace gasket(s) if necessary.

• Check control system for dam-

age.

• Replace if necessary.

600 mi

(1000 km)

or

1 month

√√√√√√

√√√√√√

6-3

4000 mi

(7000 km)

or

6 months

√√√√√

√ Replace. √ Replace. √

√√√√√

√√√√√

√√√√√

8000 mi

(13000 km)

or

12 months

12000 mi

(19000 km)

or

18 months

√

16000 mi

(25000 km)

or

24 months

EAU17600

20000 mi

(31000 km)

or

30 months

PERIODIC MAINTENANCE AND MINOR REPAIR

General maintenance and lubrication chart

No. ITEM ROUTINE

1 * Air filter element

2 * Clutch

3 * Front brake

4 * Rear brake

5 * Brake hoses

6 * Wheels (XVS11X)

Wheels

7 *

(XVS11AWX/XVS11
ATX)

8 * Tires

• Clean with compressed air.

• Replace if necessary.

• Check operation.

• Adjust or replace cable.

• Check operation, fluid level, and

for fluid leakage.

• Replace brake pads if necessary.

• Check operation, fluid level, and

for fluid leakage.

• Replace brake pads if necessary.

• Check for cracks or damage. √√√√√

• Replace. Every 4 years

• Check runout, spoke tightness

and for damage.

• Tighten spokes if necessary.

• Check runout and for damage.

• Replace if necessary.

• Check tread depth and for dam-

age.

• Replace if necessary.

• Check air pressure.

• Correct if necessary.

EAU32185

INITIAL ODOMETER READINGS

600 mi

(1000 km)

or

1 month

√√√√√√

√√√√√√

√√√√√√

4000 mi

(7000 km)

or

6 months

√√√√√

√√√√√

√√√√√

√√√√√

8000 mi

(13000 km)

or

12 months

12000 mi

(19000 km)

or

18 months

16000 mi

(25000 km)

or

24 months

20000 mi

(31000 km)

or

30 months

6

6-4

PERIODIC MAINTENANCE AND MINOR REPAIR

INITIAL ODOMETER READINGS

No. ITEM ROUTINE

9 * Wheel bearings

Swingarm pivot

10 *

bearings

11 * Steering bearings

6

12 * Chassis fasteners

Brake lever pivot

13

shaft

Brake pedal pivot

14

shaft

Clutch lever pivot

15

shaft

Shift pedal pivot

16

shaft

17 Sidestand pivot

• Check bearings for smooth oper­ation.

• Replace if necessary.

• Check bearing assemblies for

looseness.

• Moderately repack with lithium­soap-based grease.

• Check bearing assemblies for
looseness.

• Moderately repack with lithium­soap-based grease every 16000
mi (25000 km) or 24 months.

• Check all chassis fitting and fas­teners.

• Correct if necessary.

• Apply silicone grease lightly. √√√√√

• Apply silicone grease lightly. √√√√√

• Apply lithium-soap-based grease

(all-purpose grease) lightly.

• Apply lithium-soap-based grease
(all-purpose grease) lightly.

• Check operation.

• Apply lithium-soap-based grease

(all-purpose grease) lightly.

600 mi

(1000 km)

or

1 month

√√√√Repack. √

4000 mi

(7000 km)

6 months

8000 mi

or

(13000 km)

or

12 months

√√√√√

√ Repack.

√√√√√

√√√√√

√√√√√

√√√√√

12000 mi

(19000 km)

or

18 months

16000 mi

(25000 km)

or

24 months

20000 mi

(31000 km)

or

30 months

6-5

PERIODIC MAINTENANCE AND MINOR REPAIR

No. ITEM ROUTINE

18 * Sidestand switch

19 * Front fork

Shock absorber as-

20 *

sembly

Rear suspension

21 *

link pivots

22 Engine oil

Engine oil filter ele-

23 *

ment

24 Final gear oil

Front and rear brake

25 *

switches

26 * Control cables

• Check operation and replace if
necessary.

• Check operation and for oil leak­age.

• Replace if necessary.

• Check operation and for oil leak-

age.

• Replace if necessary.

• Apply lithium-soap-based grease

lightly.

• Change (warm engine before
draining).

• Replace. √√√

• Check oil level and for oil leakage.

• Change at initial 600 mi (1000

km) or 1 month, and thereafter
every 16000 mi (25000 km) or 24
months.

• Check operation. √√√√√√

• Apply Yamaha chain and cable

lube or engine oil SAE 10W-30
thoroughly.

INITIAL ODOMETER READINGS

600 mi

(1000 km)

or

1 month

√√√√√√

√√√√√√

Change. √√√Change. √

√√√√√√

4000 mi

(7000 km)

or

6 months

√√√√√

√√√√√

8000 mi

(13000 km)

or

12 months

12000 mi

(19000 km)

or

18 months

16000 mi

(25000 km)

or

24 months

√

20000 mi

(31000 km)

or

30 months

6

6-6

PERIODIC MAINTENANCE AND MINOR REPAIR

INITIAL ODOMETER READINGS

No. ITEM ROUTINE

• Check operation and free play.

Throttle grip hous-

27 *

ing and cable

Lights, signals and

28 *

switches

* Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.

• Adjust the throttle cable free play
if necessary.

• Lubricate the throttle grip housing
and cable.

• Check operation.

• Adjust headlight beam.

600 mi

(1000 km)

or

1 month

√√√√√√

NOTE:

From 24000 mi (37000 km) or 36 months, repeat the maintenance intervals starting from 8000 mi (13000 km) or 12 months.

6

NOTE:

● The air filter needs more frequent service if you are riding in unusually wet or dusty areas.

● Hydraulic brake service

• After disassembling the brake master cylinders and calipers, always change the fluid. Regularly check the brake fluid
levels and fill the reservoirs as required.

• Every two years replace the internal components of the brake master cylinders and calipers, and change the brake
fluid.

• Replace the brake hoses every four years and if cracked or damaged.

4000 mi

(7000 km)

or

6 months

√√√√√

8000 mi

(13000 km)

or

12 months

12000 mi

(19000 km)

or

18 months

16000 mi

(25000 km)

or

24 months

20000 mi

(31000 km)

or

30 months

EAU17630

6-7

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU18751

Removing and installing the
panel

The panel shown needs to be removed
to perform some of the maintenance
jobs described in this chapter. Refer to
this section each time the panel needs
to be removed and installed.

1. Panel A

EAU19151

Panel A

To remove the panel
Remove the bolt, and then pull the pan­el off as shown.

1. Bolt

To install the panel
Place the panel in the original position,
and then install the bolt.

EAU19552

Checking the spark plugs

The spark plugs are important engine
components, which are easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plugs should be removed and checked
in accordance with the periodic mainte­nance and lubrication chart. In addition,
the condition of the spark plugs can re­veal the condition of the engine.

To remove a spark plug

1. Remove the appropriate spark
plug cover (rear right or front left)
by pulling it off as shown.

1. Spark plug cover

6

6-8

2. Remove the spark plug cap.

PERIODIC MAINTENANCE AND MINOR REPAIR

3. Remove the spark plug as shown,
with the spark plug wrench includ­ed in the owner’s tool kit.

1. Spark plug wrench

To check the spark plugs

6

1. Check that the porcelain insulator
around the center electrode on
each spark plug is a medium-to­light tan (the ideal color when the
vehicle is ridden normally).

2. Check that all spark plugs installed
in the engine have the same color.

NOTE:

If any spark plug shows a distinctly dif­ferent color, the engine could be oper­ating improperly. Do not attempt to

diagnose such problems yourself. In­stead, have a Yamaha dealer check
the vehicle.

3. Check each spark plug for elec­trode erosion and excessive car­bon or other deposits, and replace
it if necessary.

Specified spark plug:

NGK/BPR7ES
DENSO/W22EPR-U

To install a spark plug

1. Measure the spark plug gap with a
wire thickness gauge and, if nec­essary, adjust the gap to specifica­tion.

1. Spark plug gap

Spark plug gap:

0.7–0.8 mm (0.028–0.031 in)

2. Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.

3. Install the spark plug with the
spark plug wrench, and then tight­en it to the specified torque.

Tightening torque:

Spark plug:

20 Nm (2.0 m·kgf, 14 ft·lbf)

NOTE:

If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4–1/2 turn
past finger tight. However, the spark
plug should be tightened to the speci­fied torque as soon as possible.

4. Install the spark plug cap.

5. Place the spark plug cover in the
original position.

6-9

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU19672

Canister (for California only)

This model is equipped with a canister
to prevent the discharging of fuel vapor
into the atmosphere.

● Check each hose connection.

● Check each hose and canister for

cracks or damage. Replace if dam­aged.

● Make sure the vent hose is not

blocked. Clean it if necessary.

EAU19822

Engine oil

The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil filter ele­ment replaced at the intervals specified
in the periodic maintenance and lubri­cation chart.

To check the engine oil level

1. Place the vehicle on a level sur­face and hold it in an upright posi­tion.

NOTE:

Make sure that the vehicle is positioned
straight up when checking the oil level.
A slight tilt to the side can result in a
false reading.

2. Start the engine, warm it up for
several minutes, and then turn it
off.

3. Wait a few minutes until the oil set­tles, and then check the oil level
through the check window located
at the bottom-left side of the crank­case.

NOTE:

The engine oil should be between the
minimum and maximum level marks.

1. Engine oil level check window

2. Maximum level mark

3. Minimum level mark

4. If the engine oil is at or below the
minimum level mark, add sufficient
oil of the recommended type to
raise it to the correct level.

To change the engine oil

1. Start the engine, warm it up for
several minutes, and then turn it
off.

2. Place an oil pan under the engine
to collect the used oil.

6

6-10

PERIODIC MAINTENANCE AND MINOR REPAIR

3. Remove the engine oil filler cap
and drain bolt to drain the oil from
the crankcase.

1. Engine oil filler cap

6

1. Engine oil drain bolt

4. Install the engine oil drain bolt, and
then tighten it to the specified
torque.

NOTE:

Check the washer for damage and re­place it if necessary.

Tightening torque:

Engine oil drain bolt:

43 Nm (4.3 m·kgf, 31 ft·lbf)

5. Add the specified amount of the
recommended engine oil, and then
install and tighten the oil filler cap.

Recommended engine oil:

See page 8-1.

Oil change quantity:

3.00 L (3.17 US qt) (2.64 Imp.qt)

ECA11620

CAUTION:

● In order to prevent clutch slip-

page (since the engine oil also
lubricates the clutch), do not
mix any chemical additives. Do
not use oils with a diesel speci­fication of “CD” or oils of a high­er quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.

● Make sure that no foreign mate-

rial enters the crankcase.

6. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking, im­mediately turn the engine off and
check for the cause.

NOTE:

After the engine is started, the engine
oil level warning light should go off if the
oil level is sufficient.

ECA10400

CAUTION:

If the oil level warning light flickers
or remains on, immediately turn the
engine off and have a Yamaha dealer
check the vehicle.

7. Turn the engine off, and then
check the oil level and correct it if
necessary.

NOTE:

Have a Yamaha dealer replace the oil
filter element at the intervals specified
in the periodic maintenance and lubri­cation chart.

6-11

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU20022

Final gear oil

The final gear case must be checked
for oil leakage before each ride. If any
leakage is found, have a Yamaha deal­er check and repair the vehicle. In addi­tion, the final gear oil level must be
checked and the oil changed as follows
at the intervals specified in the periodic
maintenance and lubrication chart.

EWA10370

WARNING

● Make sure that no foreign mate-

rial enters the final gear case.

● Make sure that no oil gets on the

tire or wheel.

To check the final gear oil level

1. Place the vehicle on a level sur­face and hold it in an upright posi­tion.

NOTE:

● The final gear oil level must be

checked on a cold engine.

● Make sure that the vehicle is posi-

tioned straight up when checking
the oil level. A slight tilt to the side
can result in a false reading.

2. Remove the oil filler bolt, and then
check the oil level in the final gear
case.

NOTE:

The oil level should be at the brim of the
filler hole.

1. Final gear oil drain bolt

2. Final gear oil filler bolt

3. Correct oil level

3. If the oil is below the brim of the fill­er hole, add sufficient oil of the rec­ommended type to raise it to the
correct level.

To change the final gear oil

1. Place an oil pan under the final
gear case to collect the used oil.

2. Remove the oil filler bolt and drain
bolt to drain the oil from the final
gear case.

3. Install the final gear oil drain bolt,
and then tighten it to the specified
torque.

Tightening torque:

Final gear oil drain bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

4. Add the recommended final gear
oil to the brim of the filler hole.

Recommended final gear oil:

SAE80 API GL-4 Hypoid gear oil

Oil quantity:

0.19 L (0.20 US qt) (0.17 Imp.qt)

NOTE:

GL4 is a quality rating. Hypoid gear oils
rated GL5 or GL6 may also be used.

5. Install the oil filler bolt, and then
tighten it to the specified torque.

Tightening torque:

Final gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

6

6-12

PERIODIC MAINTENANCE AND MINOR REPAIR

6. Check the final gear case for oil
leakage. If oil is leaking, check for
the cause.

6

EAU20670

Cleaning the air filter element

The air filter element should be cleaned
as follows at the intervals specified in
the periodic maintenance and lubrica­tion chart. Clean the air filter element
more frequently if you are riding in un­usually wet or dusty areas.

1. Remove the air filter case cover by
removing the screws.

1. Air filter case cover

2. Screw

2. Pull the air filter element out.

3. Lightly tap the air filter element to
remove most of the dust and dirt,
and then blow the remaining dirt
out with compressed air as shown.
If the air filter element is damaged,
replace it.

4. Insert the air filter element into the
air filter case as shown.

1. Air filter element

2. Projection

3. Slot

6-13

PERIODIC MAINTENANCE AND MINOR REPAIR

ECA10480

CAUTION:

● Make sure that the air filter ele-

ment is properly seated in the
air filter case.

● The engine should never be op-

erated without the air filter ele­ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.

5. Install the air filter case cover by in­stalling the screws.

EAU21271

Carburetors

The carburetors are important parts of
the engine and emission control sys­tem, which require very sophisticated
adjustment. Therefore, all carburetor
adjustments should be left to a Yamaha
dealer, who has the necessary profes­sional knowledge and experience.

EAU21311

Checking the engine idling
speed

The engine idling speed must be
checked as follows and, if necessary,
adjusted by a Yamaha dealer at the in­tervals specified in the periodic mainte­nance and lubrication chart.
Start the engine and warm it up for sev­eral minutes at 1000–2000 r/min while
occasionally revving it to 4000–5000
r/min.

NOTE:

The engine is warm when it quickly re­sponds to the throttle.

Engine idling speed:

950–1050 r/min

6

6-14

PERIODIC MAINTENANCE AND MINOR REPAIR

Checking the throttle cable
free play

1. Throttle cable free play

The throttle cable free play should mea­sure 4.0–6.0 mm (0.16–0.24 in) at the

6

throttle grip. Periodically check the
throttle cable free play and, if neces­sary, have a Yamaha dealer adjust it.

EAU21382

EAU21401

Valve clearance

The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.

EAU32520

Tires (XVS11X)

To maximize the performance, durabil­ity, and safe operation of your motor­cycle, note the following points
regarding the specified tires.

Tire air pressure

The tire air pressure should be checked
and, if necessary, adjusted before each
ride.

EWA10500

WARNING

● The tire air pressure must be

checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).

● The tire air pressure must be ad-

justed in accordance with the
riding speed and with the total
weight of rider, passenger, car­go, and accessories approved
for this model.

6-15

PERIODIC MAINTENANCE AND MINOR REPAIR

Tire air pressure (measured on cold
tires):

0–90 kg (0–198 lb):

Front:

XVS11X 200 kPa (29 psi) (2.00
kgf/cm²)
XVS11XC 200 kPa (29 psi)
(2.00 kgf/cm²)

Rear:

XVS11X 225 kPa (33 psi) (2.25
kgf/cm²)
XVS11XC 225 kPa (33 psi)
(2.25 kgf/cm²)

XVS11X 90–200 kg (198–441 lb)
XVS11XC 90–197 kg (198–434 lb):

Front:

225 kPa (33 psi) (2.25 kgf/cm²)

Rear:

250 kPa (36 psi) (2.50 kgf/cm²)

Maximum load*:

XVS11X 200 kg (441 lb)
XVS11XC 197 kg (434 lb)

* Total weight of rider, passenger, car-

go and accessories

EWA10510

WARNING

Proper loading of your vehicle is im­portant for several characteristics of
your vehicle, such as handling,
braking, performance and safety. Do
not carry loosely packed items that

can shift. Securely pack your heavi­est items close to the center of the
vehicle, and distribute the weight
evenly from side to side. Properly
adjust the suspension for your load,
and check the condition and pres­sure of your tires. NEVER OVER­LOAD YOUR VEHICLE. Make sure
that the total weight of the cargo, rid­er, passenger, and accessories
(cowling, saddlebags, etc. if ap­proved for this model) does not ex­ceed the maximum load of the
vehicle. Operation of an overloaded
vehicle could cause tire damage, an
accident, or even injury.

Tire inspection

1. Tire sidewall

2. Tire wear indicator

3. Tire tread depth

Always check the tires before operating
the motorcycle. If a tire tread shows
crosswise lines (minimum tread depth),
if the tire has a nail or glass fragments
in it, or if the sidewall is cracked, con­tact a Yamaha dealer immediately and
have the tire replaced.

Minimum tire tread depth (front and
rear):

1.0 mm (0.04 in)

6

6-16

PERIODIC MAINTENANCE AND MINOR REPAIR

WARNING

● It is dangerous to ride with a

worn-out tire. When a tire tread
begins to show crosswise lines,
have a Yamaha dealer replace
the tire immediately.

● The replacement of all wheel-

and brake-related parts, includ­ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl­edge and experience.

● It is not recommended to patch

a punctured tube. If unavoid-

6

able, however, patch the tube
very carefully and replace it as
soon as possible with a high­quality product.

Tire information

This motorcycle is equipped with spoke
wheels and tube tires.

EWA10560

EWA10460

WARNING

● The front and rear tires should

be of the same make and de­sign, otherwise the handling
characteristics of the vehicle
cannot be guaranteed.

● After extensive tests, only the

tires listed below have been ap­proved for this model by
Yamaha Motor Co., Ltd.

Front tire:

Size:

XVS11X 110/90-18M/C 61S
XVS11XC 110/90-18M/C 61S

Manufacturer/model:

XVS11X DUNLOP/K555F
XVS11XC DUNLOP/K555F
XVS11X BRIDGESTONE/EXE­DRA L309
XVS11XC BRIDGESTONE/EXE­DRA L309

Rear tire:

Size:

170/80-15M/C 77S

Manufacturer/model:

XVS11X DUNLOP/K555
XVS11XC DUNLOP/K555
XVS11X BRIDGESTONE/EXE­DRA G546G
XVS11XC BRIDGESTONE/EXE­DRA G546G

6-17

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU32541

Tires (XVS11AWX/XVS11ATX)

To maximize the performance, durabil­ity, and safe operation of your motor­cycle, note the following points
regarding the specified tires.

Tire air pressure

The tire air pressure should be checked
and, if necessary, adjusted before each
ride.

EWA10500

WARNING

● The tire air pressure must be

checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).

● The tire air pressure must be ad-

justed in accordance with the
riding speed and with the total
weight of rider, passenger, car­go, and accessories approved
for this model.

Tire air pressure (measured on cold
tires):

0–90 kg (0–198 lb):

Front:

XVS11ATX 225 kPa (33 psi)
(2.25 kgf/cm²)
XVS11ATXC 225 kPa (33 psi)
(2.25 kgf/cm²)
XVS11AWX 225 kPa (33 psi)
(2.25 kgf/cm²)
XVS11AWXC 225 kPa (33 psi)
(2.25 kgf/cm²)

Rear:

XVS11ATX 250 kPa (36 psi)
(2.50 kgf/cm²)
XVS11ATXC 250 kPa (36 psi)
(2.50 kgf/cm²)
XVS11AWX 250 kPa (36 psi)
(2.50 kgf/cm²)
XVS11AWXC 250 kPa (36 psi)
(2.50 kgf/cm²)

XVS11ATX 90–203 kg (198–448 lb)
XVS11ATXC 90–200 kg (198–441
lb)
XVS11AWX 90–203 kg (198–448 lb)
XVS11AWXC 90–200 kg (198–441
lb):

Front:

225 kPa (33 psi) (2.25 kgf/cm²)

Rear:

250 kPa (36 psi) (2.50 kgf/cm²)

Maximum load*:

XVS11ATX 203 kg (448 lb)
XVS11ATXC 200 kg (441 lb)
XVS11AWX 203 kg (448 lb)
XVS11AWXC 200 kg (441 lb)

* Total weight of rider, passenger, car-

go and accessories

EWA10510

WARNING

Proper loading of your vehicle is im­portant for several characteristics of
your vehicle, such as handling,
braking, performance and safety. Do
not carry loosely packed items that
can shift. Securely pack your heavi­est items close to the center of the
vehicle, and distribute the weight
evenly from side to side. Properly
adjust the suspension for your load,
and check the condition and pres­sure of your tires. NEVER OVER­LOAD YOUR VEHICLE. Make sure
that the total weight of the cargo, rid­er, passenger, and accessories
(cowling, saddlebags, etc. if ap­proved for this model) does not ex­ceed the maximum load of the

6

6-18

PERIODIC MAINTENANCE AND MINOR REPAIR

vehicle. Operation of an overloaded
vehicle could cause tire damage, an
accident, or even injury.

Tire inspection

1. Tire sidewall

6

2. Tire wear indicator

3. Tire tread depth

Always check the tires before operating
the motorcycle. If a tire tread shows
crosswise lines (minimum tread depth),
if the tire has a nail or glass fragments
in it, or if the sidewall is cracked, con­tact a Yamaha dealer immediately and
have the tire replaced.

EWA10520

WARNING

It is dangerous to ride with a worn­out tire. When a tire tread begins to
show lines, have a Yamaha dealer
replace the tire immediately. Brakes,
tires and related wheel parts re­placement should also be left to a
Yamaha dealer.

Tire information

This motorcycle is equipped with cast
wheels and tubeless tires.

EWA10460

WARNING

● The front and rear tires should

be of the same make and de­sign, otherwise the handling
characteristics of the vehicle
cannot be guaranteed.

● After extensive tests, only the

tires listed below have been ap­proved for this model by
Yamaha Motor Co., Ltd.

Front tire:

Size:

XVS11ATX 130/90-16M/C 67S
XVS11ATXC 130/90-16M/C 67S
XVS11AWX 130/90-16M/C 67S
XVS11AWXC 130/90-16M/C 67S

Manufacturer/model:

XVS11ATX DUNLOP/D404F
XVS11ATXC DUNLOP/D404F
XVS11AWX DUNLOP/D404F
XVS11AWXC DUNLOP/D404F
XVS11ATX BRIDGESTONE/EXE­DRA G703
XVS11ATXC BRIDGE­STONE/EXEDRA G703
XVS11AWX BRIDGE­STONE/EXEDRA G703
XVS11AWXC BRIDGE­STONE/EXEDRA G703

Minimum tire tread depth (front and
rear):

1.0 mm (0.04 in)

6-19

PERIODIC MAINTENANCE AND MINOR REPAIR

Rear tire:

Size:

170/80-15M/C 77S

Manufacturer/model:

XVS11ATX DUNLOP/D404G
XVS11ATXC DUNLOP/D404G
XVS11AWX DUNLOP/D404G
XVS11AWXC DUNLOP/D404G
XVS11ATX BRIDGESTONE/EXE­DRA G702
XVS11ATXC BRIDGE­STONE/EXEDRA G702
XVS11AWX BRIDGE­STONE/EXEDRA G702
XVS11AWXC BRIDGE­STONE/EXEDRA G702

EAU21940

Spoke wheels (XVS11X)

To maximize the performance, durabil­ity, and safe operation of your motor­cycle, note the following points
regarding the specified wheels.

● The wheel rims should be checked

for cracks, bends or warpage, and
the spokes for looseness or dam­age before each ride. If any dam­age is found, have a Yamaha
dealer replace the wheel. Do not
attempt even the smallest repair to
the wheel. A deformed or cracked
wheel must be replaced.

● The wheel should be balanced

whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han­dling characteristics, and a short­ened tire life.

● Ride at moderate speeds after

changing a tire since the tire sur­face must first be “broken in” for it
to develop its optimal characteris­tics.

EAU21992

Cast wheels
(XVS11AWX/XVS11ATX)

To maximize the performance, durabil­ity, and safe operation of your vehicle,
note the following points regarding the
specified wheels.

● The wheel rims should be checked

for cracks, bends, warpage or
damage before each ride. If any
damage is found, have a Yamaha
dealer replace the wheel. Do not
attempt even the smallest repair to
the wheel. A deformed or cracked
wheel must be replaced.

● The wheel should be balanced

whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse han­dling characteristics, and a short­ened tire life.

● Ride at moderate speeds after

changing a tire since the tire sur­face must first be “broken in” for it
to develop its optimal characteris­tics.

6

6-20

PERIODIC MAINTENANCE AND MINOR REPAIR

● After repairing or replacing the rear

tire, tighten the valve stem nut and
locknut to the specified torques.

1. Valve stem nut

2. Valve stem locknut

6

Tightening torques:

Valve stem nut:

1.5 Nm (0.15 m·kgf, 1.08 ft·lbf)

Valve stem locknut:

3.0 Nm (0.30 m·kgf, 2.17 ft·lbf)

EAU22011

Accessories and replacement
parts

EWA10621

any consequences caused by the
use of items which have not been
approved by Yamaha.

WARNING

This vehicle is not designed to pull a
trailer or to be attached to a sidecar.
The accessories or replacement
parts you choose for your vehicle
should be designed specifically for

1
2

this model, and they must be se­curely mounted to maintain the in­herent stability of the original
design. Genuine Yamaha Parts and
Accessories are designed and test­ed to be compatible with your vehi­cle. Please consider Genuine
Yamaha Parts and Accessories be­fore making a purchase. Use of non­Yamaha-approved accessories or
replacement parts may cause loss of
handling stability and riding safety.
Since Yamaha cannot control the
quality of accessories or parts man­ufactured by other companies,
Yamaha cannot be held liable for

6-21

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU22020

Adjusting the clutch lever free
play

1. Locknut

2. Clutch lever free play adjusting bolt

3. Clutch lever free play

The clutch lever free play should mea­sure 5.0–10.0 mm (0.20–0.39 in) as
shown. Periodically check the clutch le­ver free play and, if necessary, adjust it
as follows.

1. Loosen the locknut at the clutch le­ver.

2. To increase the clutch lever free
play, turn the adjusting bolt in di­rection (a). To decrease the clutch
lever free play, turn the adjusting
bolt in direction (b).

3. Tighten the locknut.

NOTE:

If the specified free play cannot be ob­tained as described above or if the
clutch does not operate correctly, have
a Yamaha dealer check the internal
clutch mechanism.

EAU22092

Adjusting the brake lever free
play

1. Brake lever free play

The brake lever free play should mea­sure 5.0–8.0 mm (0.20–0.31 in) as
shown. Periodically check the brake le­ver free play and, if necessary, adjust it
as follows.

6

6-22

PERIODIC MAINTENANCE AND MINOR REPAIR

1. Locknut

2. Brake lever free play adjusting screw

1. Loosen the locknut at the brake le­ver.

2. To increase the brake lever free

6

play, turn the adjusting screw in di­rection (a). To decrease the brake
lever free play, turn the adjusting
screw in direction (b).

3. Tighten the locknut.

WARNING

● After adjusting the brake lever

free play, check the free play
and make sure that the brake is
working properly.

● A soft or spongy feeling in the

brake lever can indicate the
presence of air in the hydraulic

EWA10630

system. If there is air in the hy­draulic system, have a Yamaha
dealer bleed the system before
operating the motorcycle. Air in
the hydraulic system will dimin­ish the braking performance,
which may result in loss of con­trol and an accident.

6-23

EAU22270

Adjusting the rear brake light
switch

1. Rear brake light switch

2. Rear brake light switch adjusting nut

The rear brake light switch, which is ac­tivated by the brake pedal, is properly
adjusted when the brake light comes
on just before braking takes effect. If
necessary, adjust the brake light switch
as follows.
Turn the adjusting nut while holding the
rear brake light switch in place. To
make the brake light come on earlier,
turn the adjusting nut in direction (a). To
make the brake light come on later, turn
the adjusting nut in direction (b).

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU22321

Checking the front and rear
brake pads

Front brake

1. Brake pad wear indicator groove

Rear brake

1. Brake pad wear indicator groove

The front and rear brake pads must be
checked for wear at the intervals spec­ified in the periodic maintenance and
lubrication chart. Each brake pad is
provided with a wear indicator groove,
which allows you to check the brake
pad wear without having to disassem­ble the brake. To check the brake pad
wear, check the wear indicator
grooves. If a brake pad has worn to the
point that the wear indicator groove has
almost disappeared, have a Yamaha
dealer replace the brake pads as a set.

EAU22580

Checking the brake fluid level

Front brake

1. Minimum level mark

Rear brake

6

1. Minimum level mark

Insufficient brake fluid may allow air to
enter the brake system, possibly caus­ing it to become ineffective.

6-24

PERIODIC MAINTENANCE AND MINOR REPAIR

Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads
and/or brake system leakage. If the
brake fluid level is low, be sure to check
the brake pads for wear and the brake
system for leakage.
Observe these precautions:

● When checking the fluid level,

make sure that the top of the brake
fluid reservoir is level.

● Use only the recommended quality

brake fluid, otherwise the rubber
seals may deteriorate, causing

6

leakage and poor braking perfor­mance.

Recommended brake fluid:

DOT 4

● Refill with the same type of brake

fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performance.

● Be careful that water does not en-

ter the brake fluid reservoir when
refilling. Water will significantly
lower the boiling point of the fluid
and may result in vapor lock.

● Brake fluid may deteriorate paint-

ed surfaces or plastic parts. Al­ways clean up spilled fluid
immediately.

● As the brake pads wear, it is nor-

mal for the brake fluid level to grad­ually go down. However, if the
brake fluid level goes down sud­denly, have a Yamaha dealer
check the cause.

EAU22730

Changing the brake fluid

Have a Yamaha dealer change the
brake fluid at the intervals specified in
the NOTE after the periodic mainte­nance and lubrication chart. In addition,
have the oil seals of the master cylin­ders and calipers as well as the brake
hoses replaced at the intervals listed
below or whenever they are damaged
or leaking.

● Oil seals: Replace every two

years.

● Brake hoses: Replace every four

years.

6-25

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU23091

Checking and lubricating the
cables

The operation of all control cables and
the condition of the cables should be
checked before each ride, and the ca­bles and cable ends should be lubricat­ed if necessary. If a cable is damaged
or does not move smoothly, have a
Yamaha dealer check or replace it.

Recommended lubricant:

Yamaha Chain and Cable Lube or
engine oil SAE 10W-30

EWA10710

WARNING

Damage to the outer housing of ca­bles may result in internal rusting
and cause interference with cable
movement. Replace damaged ca­bles as soon as possible to prevent
unsafe conditions.

EAU23111

Checking and lubricating the
throttle grip and cable

The operation of the throttle grip should
be checked before each ride. In addi­tion, the cable should be lubricated at
the intervals specified in the periodic
maintenance chart.

EAU23132

Checking and lubricating the
brake and shift pedals

6

The operation of the brake and shift
pedals should be checked before each
ride, and the pedal pivots should be lu­bricated if necessary.

6-26

PERIODIC MAINTENANCE AND MINOR REPAIR

Recommended lubricants:

Brake pedal:

Silicone grease

Shift pedal:

Lithium-soap-based grease (all­purpose grease)

Checking and lubricating the
brake and clutch levers

The operation of the brake and clutch
levers should be checked before each

6

ride, and the lever pivots should be lu­bricated if necessary.

EAU23141

Checking and lubricating the
sidestand

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if

EAU23200

necessary.

Recommended lubricants:

Brake lever:

Silicone grease

Clutch lever:

Lithium-soap-based grease (all­purpose grease)

WARNING

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it.

EWA10730

6-27

Recommended lubricant:

Lithium-soap-based grease (all-pur­pose grease)

PERIODIC MAINTENANCE AND MINOR REPAIR

EAUM1650

Lubricating the swingarm piv­ots

The swingarm pivots must be lubricat­ed at the intervals specified in the peri­odic maintenance and lubrication chart.

Recommended lubricant:

Lithium-soap-based grease

EAU23250

Lubricating the rear suspen­sion

The pivoting points of the rear suspen­sion must be lubricated at the intervals
specified in the periodic maintenance
and lubrication chart.

Recommended lubricant:

Lithium-soap-based grease

EAU23271

Checking the front fork

The condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main­tenance and lubrication chart.

To check the condition

EWA10750

WARNING

Securely support the vehicle so that
there is no danger of it falling over.

Check the inner tubes for scratches,
damage and excessive oil leakage.

To check the operation

1. Place the vehicle on a level sur­face and hold it in an upright posi­tion.

2. While applying the front brake,
push down hard on the handlebars
several times to check if the front
fork compresses and rebounds
smoothly.

6

6-28

PERIODIC MAINTENANCE AND MINOR REPAIR

Checking the steering

Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol­lows at the intervals specified in the pe­riodic maintenance and lubrication
chart.

1. Place a stand under the engine to
raise the front wheel off the
ground.

WARNING

Securely support the vehicle so that
there is no danger of it falling over.

2. Hold the lower ends of the front
fork legs and try to move them for­ward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.

CAUTION:

If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or re-

6

pair it.

ECA10590

EAU23280

EWA10750

6-29

PERIODIC MAINTENANCE AND MINOR REPAIR

EAU23290

Checking the wheel bearings

The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica­tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer check
the wheel bearings.

EAU23380

Battery

1. Positive battery lead (red)

2. Negative battery lead (black)

The battery is located behind panel A.
(See page 6-8.)
This model is equipped with a sealed­type (MF) battery, which does not re­quire any maintenance. There is no
need to check the electrolyte or to add
distilled water.

ECA10620

CAUTION:

Never attempt to remove the battery
cell seals, as this would permanent­ly damage the battery.

EWA10760

WARNING

● Electrolyte is poisonous and

dangerous since it contains sul­furic acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al­ways shield your eyes when
working near batteries. In case
of contact, administer the fol­lowing FIRST AID.

• EXTERNAL: Flush with plenty
of water.

• INTERNAL: Drink large quan­tities of water or milk and im­mediately call a physician.

• EYES: Flush with water for 15
minutes and seek prompt
medical attention.

● Batteries produce explosive hy-

drogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and pro­vide sufficient ventilation when
charging it in an enclosed
space.

6

6-30

PERIODIC MAINTENANCE AND MINOR REPAIR

● KEEP THIS AND ALL BATTER-

IES OUT OF THE REACH OF
CHILDREN.

To charge the battery

Have a Yamaha dealer charge the bat­tery as soon as possible if it seems to
have discharged. Keep in mind that the
battery tends to discharge more quickly
if the vehicle is equipped with optional
electrical accessories.

To store the battery

1. If the vehicle will not be used for

6

more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.

2. If the battery will be stored for more
than two months, check it at least
once a month and fully charge it if
necessary.

3. Fully charge the battery before in­stallation.

4. After installation, make sure that
the battery leads are properly con­nected to the battery terminals.

ECA10630

CAUTION:

● Always keep the battery

charged. Storing a discharged
battery can cause permanent
battery damage.

● To charge a sealed-type (MF)

battery, a special (constant-volt­age) battery charger is required.
Using a conventional battery
charger will damage the battery.
If you do not have access to a
sealed-type (MF) battery charg­er, have a Yamaha dealer
charge your battery.

EAU27102

Replacing the fuses

The main fuse is located under the igni­tor unit panel.
The fuse box, which contains the fuses
for the individual circuits, is located in­side the storage compartment. (See
page 3-13.)

1. Backup fuse (for odometer)

2. Spare fuse

3. Headlight fuse

4. Signaling system fuse

5. Ignition fuse

6. Carburetor heater fuse

7. Ignitor unit fuse

If a fuse is blown, replace it as follows.

NOTE:

Include steps 1–3 and 8–9 only for the
main fuse.

6-31

PERIODIC MAINTENANCE AND MINOR REPAIR

1. Remove the rider seat. (See page
3-9.)

2. Remove the quick fasteners
shown by pushing the center in
with a screwdriver, then pulling the
fastener out.

1. Quick fastener

3. Pull the ignitor unit panel outward
to the right.

1. Ignitor unit panel

2. Spare main fuse

3. Main fuse

4. Turn the key to “OFF” and turn off
the electrical circuit in question.

5. Remove the blown fuse, and then
install a new fuse of the specified
amperage.

Specified fuses:

Main fuse:

30.0 A

Backup fuse:

5.0 A

Ignition fuse:

10.0 A

Headlight fuse:

15.0 A

Carburetor heater fuse:

15.0 A

Signaling system fuse:

10.0 A

Ignitor unit fuse:

5.0 A

ECA10640

CAUTION:

Do not use a fuse of a higher amper­age rating than recommended to
avoid causing extensive damage to
the electrical system and possibly a
fire.

6. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.

7. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.

6

6-32

PERIODIC MAINTENANCE AND MINOR REPAIR

8. Place the ignitor unit panel in the
original position and install the
quick fasteners.

NOTE:

To install a quick fastener, push its pin
back so that it will protrude from the fas­tener head, then insert the fastener and
push the protruding pin in until it is flush
with the fastener head.

6

1. Quick fastener (after removal)

2. Quick fastener (before installation)

9. Install the rider seat.

EAU23792

Replacing the headlight bulb

This model is equipped with a quartz
bulb headlight. If the headlight bulb
burns out, replace it as follows.

1. Remove the headlight unit by re­moving the screws.

1. Screw

2. Disconnect the headlight coupler,
and then remove the bulb cover.

3. Unhook the headlight bulb holder,
and then remove the defective
bulb.

1. Headlight bulb holder

EWA10790

WARNING

Headlight bulbs get very hot. There­fore, keep flammable products away
from a lit headlight bulb, and do not
touch the bulb until it has cooled
down.

4. Place a new headlight bulb into po­sition, and then secure it with the
bulb holder.

ECA10660

CAUTION:

Do not touch the glass part of the
headlight bulb to keep it free from
oil, otherwise the transparency of
the glass, the luminosity of the bulb,
and the bulb life will be adversely af-

6-33

PERIODIC MAINTENANCE AND MINOR REPAIR

fected. Thoroughly clean off any dirt
and fingerprints on the headlight
bulb using a cloth moistened with al­cohol or thinner.

1. Do not touch the glass part of the bulb.

5. Install the headlight bulb cover,
and then connect the coupler.

6. Install the headlight unit by install­ing the screws.

7. Have a Yamaha dealer adjust the
headlight beam if necessary.

EAU24281

Replacing a turn signal light
bulb or the tail/brake light bulb

1. Remove the lens by removing the
screws.

1. Screw

XVS11X

XVS11AWX/XVS11ATX

1. Screw

2. Remove the defective bulb by
pushing it in and turning it counter­clockwise.

3. Insert a new bulb into the socket,
push it in, and then turn it clock­wise until it stops.

4. Install the lens by installing the
screws.

ECA10680

CAUTION:

Do not overtighten the screws, oth­erwise the lens may break.

6

1. Screw

6-34

PERIODIC MAINTENANCE AND MINOR REPAIR

Supporting the motorcycle

Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other maintenance
requiring the motorcycle to stand up­right. Check that the motorcycle is in a
stable and level position before starting
any maintenance. A strong wooden
box can be placed under the engine for
added stability.

To service the front wheel

1. Stabilize the rear of the motorcycle

6

by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un­der the frame in front of the rear
wheel.

2. Raise the front wheel off the
ground by using a motorcycle
stand.

To service the rear wheel

Raise the rear wheel off the ground by
using a motorcycle stand or, if a motor­cycle stand is not available, by placing

EAU24350

a jack either under each side of the
frame in front of the rear wheel or under
each side of the swingarm.

EAU25850

Troubleshooting

Although Yamaha motorcycles receive
a thorough inspection before shipment
from the factory, trouble may occur dur­ing operation. Any problem in the fuel,
compression, or ignition systems, for
example, can cause poor starting and
loss of power.
The following troubleshooting chart
represents a quick and easy procedure
for checking these vital systems your­self. However, should your motorcycle
require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the motorcycle
properly.
Use only genuine Yamaha replace­ment parts. Imitation parts may look like
Yamaha parts, but they are often inferi­or, have a shorter service life and can
lead to expensive repair bills.

6-35

PERIODIC MAINTENANCE AND MINOR REPAIR

Troubleshooting chart

WARNING

Keep away open flames and do not smoke while checking or working on the fuel system.

EAU25891

EWA10840

1. Fuel

Check the fuel level in
the fuel tank.

2. Compression

Operate the electric starter.

3. Ignition

Remove the spark plugs
and check the electrodes.

4. Battery

Operate the electric starter.

There is enough fuel.

There is no fuel.

There is compression.

There is no compression.

Wet

Dry

The engine turns over
quickly.

The engine turns over
slowly.

Wipe off with a dry cloth and correct the
spark plug gaps, or replace the spark plugs.

Have a Yamaha dealer check the vehicle.

Check the compression.

Supply fuel.

Check the ignition.

Have a Yamaha dealer
check the vehicle.

The battery is good.

Check the battery lead connections,
and charge the battery if necessary.

The engine does not start.
Check the compression.

6-36

6

Open the throttle halfway and operate
the electric starter.

The engine does not start.
Check the battery.

The engine does not start.
Have a Yamaha dealer
check the vehicle.

MOTORCYCLE CARE AND STORAGE

Matte color caution

CAUTION:

Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use be­fore cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored fin­ished parts.

7

EAU37833

ECA15192

EAU26061

Care

While the open design of a motorcycle
reveals the attractiveness of the tech­nology, it also makes it more vulnera­ble. Rust and corrosion can develop
even if high-quality components are
used. A rusty exhaust pipe may go un­noticed on a car, however, it detracts
from the overall appearance of a motor­cycle. Frequent and proper care does
not only comply with the terms of the
warranty, but it will also keep your
motorcycle looking good, extend its life
and optimize its performance.

Before cleaning

1. Cover the muffler outlets with plas­tic bags after the engine has
cooled down.

2. Make sure that all caps and covers
as well as all electrical couplers
and connectors, including the
spark plug caps, are tightly in­stalled.

3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-

7-1

ucts onto seals, gaskets and wheel
axles. Always rinse the dirt and de­greaser off with water.

Cleaning

ECA10771

CAUTION:

● Avoid using strong acidic wheel

cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the af­fected area any longer than in­structed. Also, thoroughly rinse
the area off with water, immedi­ately dry it, and then apply a cor­rosion protection spray.

● Improper cleaning can damage

plastic parts such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc. Use
only a soft, clean cloth or
sponge with mild detergent and
water to clean plastic.

● Do not use any harsh chemical

products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive

MOTORCYCLE CARE AND STORAGE

cleaning products, solvent or
thinner, fuel (gasoline), rust re­movers or inhibitors, brake flu­id, antifreeze or electrolyte.

● Do not use high-pressure wash-

ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar­eas: seals (of wheel and swing­arm bearings, fork and brakes),
electric components (couplers,
connectors, instruments,
switches and lights), breather
hoses and vents.

● For motorcycles equipped with

a windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning com­pounds for plastic may leave
scratches on the windshield.
Test the product on a small hid­den part of the windshield to
make sure that it does not leave
any marks. If the windshield is
scratched, use a quality plastic
polishing compound after
washing.

After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.

After riding in the rain, near the sea or
on salt-sprayed roads
Since sea salt or salt sprayed on roads
during winter are extremely corrosive in
combination with water, carry out the
following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.

NOTE:

Salt sprayed on roads in the winter may
remain well into spring.

1. Clean the motorcycle with cold wa­ter and a mild detergent, after the
engine has cooled down.

ECA10790

CAUTION:

Do not use warm water since it in­creases the corrosive action of the
salt.

2. After drying the motorcycle, apply
a corrosion protection spray on all
metal, including chrome- and nick­el-plated, surfaces to prevent cor­rosion.

After cleaning

1. Dry the motorcycle with a chamois
or an absorbing cloth.

2. Use a chrome polish to shine
chrome, aluminum and stainless­steel parts, including the exhaust
system. (Even the thermally in­duced discoloring of stainless­steel exhaust systems can be re­moved through polishing.)

3. To prevent corrosion, it is recom­mended to apply a corrosion pro­tection spray on all metal,
including chrome- and nickel-plat­ed, surfaces.

4. Use spray oil as a universal clean­er to remove any remaining dirt.

7

7-2

MOTORCYCLE CARE AND STORAGE

5. Touch up minor paint damage
caused by stones, etc.

6. Wax all painted surfaces.

7. Let the motorcycle dry completely
before storing or covering it.

WARNING

● Make sure that there is no oil or

wax on the brakes or tires.

● If necessary, clean the brake

discs and brake linings with a
regular brake disc cleaner or ac­etone, and wash the tires with
warm water and a mild deter­gent. Before riding at higher
speeds, test the motorcycle’s
braking performance and cor-

7

nering behavior.

CAUTION:

● Apply spray oil and wax spar-

ingly and make sure to wipe off
any excess.

● Never apply oil or wax to any

rubber and plastic parts, but
treat them with a suitable care
product.

EWA11130

ECA10800

● Avoid using abrasive polishing

compounds as they will wear
away the paint.

NOTE:

Consult a Yamaha dealer for advice on
what products to use.

7-3

EAU26230

Storage

Short-term

Always store your motorcycle in a cool,
dry place and, if necessary, protect it
against dust with a porous cover.

ECA10810

CAUTION:

● Storing the motorcycle in a

poorly ventilated room or cover­ing it with a tarp, while it is still
wet, will allow water and humid­ity to seep in and cause rust.

● To prevent corrosion, avoid

damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemi­cals are stored.

Long-term

Before storing your motorcycle for sev­eral months:

1. Follow all the instructions in the
“Care” section of this chapter.

2. For motorcycles equipped with a
fuel cock that has an “OFF” posi­tion: Turn the fuel cock lever to
“OFF”.

MOTORCYCLE CARE AND STORAGE

3. Drain the carburetor float cham­bers by loosening the drain bolts;
this will prevent fuel deposits from
building up. Pour the drained fuel
into the fuel tank.

4. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.

5. Perform the following steps to pro­tect the cylinders, piston rings, etc.
from corrosion.
a. Remove the spark plug caps

and spark plugs.

b. Pour a teaspoonful of engine oil

into each spark plug bore.

c. Install the spark plug caps onto

the spark plugs, and then place
the spark plugs on the cylinder
head so that the electrodes are
grounded. (This will limit spark­ing during the next step.)

d. Turn the engine over several

times with the starter. (This will
coat the cylinder walls with oil.)

e. Remove the spark plug caps

from the spark plugs, and then
install the spark plugs and the
spark plug caps.

EWA10950

WARNING

To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.

6. Lubricate all control cables and the
pivoting points of all levers and
pedals as well as of the side­stand/centerstand.

7. Check and, if necessary, correct
the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna­tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.

8. Cover the muffler outlets with plas­tic bags to prevent moisture from
entering them.

9. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex­cessively cold or warm place [less
than 0 °C (30 °F) or more than 30

7-4

°C (90 °F)]. For more information
on storing the battery, see page
6-30.

NOTE:

Make any necessary repairs before
storing the motorcycle.

7

SPECIFICATIONS

Dimensions:

8

Overall length:

XVS11ATX 2460 mm (96.9 in)
XVS11ATXC 2460 mm (96.9 in)
XVS11AWX 2460 mm (96.9 in)
XVS11AWXC 2460 mm (96.9 in)
XVS11X 2405 mm (94.7 in)
XVS11XC 2405 mm (94.7 in)

Overall width:

XVS11ATX 945 mm (37.2 in)
XVS11ATXC 945 mm (37.2 in)
XVS11AWX 945 mm (37.2 in)
XVS11AWXC 945 mm (37.2 in)
XVS11X 895 mm (35.2 in)
XVS11XC 895 mm (35.2 in)

Overall height:

1100 mm (43.3 in)

Seat height:

XVS11ATX 710 mm (28.0 in)
XVS11ATXC 710 mm (28.0 in)
XVS11AWX 710 mm (28.0 in)
XVS11AWXC 710 mm (28.0 in)
XVS11X 690 mm (27.2 in)
XVS11XC 690 mm (27.2 in)

Wheelbase:

XVS11ATX 1645 mm (64.8 in)
XVS11ATXC 1645 mm (64.8 in)
XVS11AWX 1645 mm (64.8 in)
XVS11AWXC 1645 mm (64.8 in)
XVS11X 1640 mm (64.6 in)
XVS11XC 1640 mm (64.6 in)

Ground clearance:

XVS11ATX 140 mm (5.51 in)
XVS11ATXC 140 mm (5.51 in)
XVS11AWX 140 mm (5.51 in)
XVS11AWXC 140 mm (5.51 in)
XVS11X 145 mm (5.71 in)
XVS11XC 145 mm (5.71 in)

Minimum turning radius:

XVS11ATX 3400 mm (133.9 in)
XVS11ATXC 3400 mm (133.9 in)
XVS11AWX 3400 mm (133.9 in)
XVS11AWXC 3400 mm (133.9 in)
XVS11X 3200 mm (126.0 in)
XVS11XC 3200 mm (126.0 in)

Weight:

With oil and fuel:

XVS11ATX 285.0 kg (628 lb)
XVS11ATXC 288.0 kg (635 lb)
XVS11AWX 285.0 kg (628 lb)
XVS11AWXC 288.0 kg (635 lb)
XVS11X 275.0 kg (606 lb)
XVS11XC 278.0 kg (613 lb)

Engine:

Engine type:

Air cooled 4-stroke, SOHC

Cylinder arrangement:

V-type 2-cylinder

Displacement:

1063.0 cm³

Bore × stroke:

95.0 × 75.0 mm (3.74 × 2.95 in)

Compression ratio:

8.30 :1

8-1

Starting system:

Electric starter

Lubrication system:

Wet sump

Engine oil:

Type:

YAMALUBE 4, SAE10W30 or SAE20W40

0°

10° 30° 50° 70° 90°

YAMALUBE 4 (10W30)

or SAE 10W30

YAMALUBE 4 (20W40)
or SAE 20W40

–20°

–10° 0° 10° 20° 30°

110°

40°

Recommended engine oil grade:

API service SG type or higher, JASO
standard MA

Engine oil quantity:

Without oil filter element replacement:

3.00 L (3.17 US qt) (2.64 Imp.qt)

With oil filter element replacement:

3.10 L (3.28 US qt) (2.73 Imp.qt)

Final gear oil:

Type:

SAE80 API GL-4 Hypoid gear oil

Quantity:

0.19 L (0.20 US qt) (0.17 Imp.qt)

Air filter:

Air filter element:

Dry element

130°F

50°C

SPECIFICATIONS

Fuel:

Recommended fuel:

Unleaded gasoline only

Fuel tank capacity:

17.0 L (4.49 US gal) (3.74 Imp.gal)

Fuel reserve amount:

4.5 L (1.19 US gal) (0.99 Imp.gal)

Carburetor:

Manufacturer:

MIKUNI

Type × quantity:

BSR37 x 2

Spark plug (s):

Manufacturer/model:

NGK/BPR7ES

Manufacturer/model:

DENSO/W22EPR-U

Spark plug gap:

0.7–0.8 mm (0.028–0.031 in)

Clutch:

Clutch type:

Wet, multiple-disc

Transmission:

Primary reduction system:

Spur gear

Primary reduction ratio:

78/47 (1.660)

Secondary reduction system:

Shaft drive

Secondary reduction ratio:

44/47 × 19/18 × 32/11 (2.875)

Transmission type:

Constant mesh 5-speed

Operation:

Left foot operation

Gear ratio:

1st:

40/17 (2.353)

2nd:

40/24 (1.667)

3rd:

36/28 (1.286)

4th:

32/31 (1.032)

5th:

29/34 (0.853)

Chassis:

Frame type:

Double cradle

Caster angle:

33.00 °

Trail:

XVS11ATX 132.0 mm (5.20 in)
XVS11ATXC 132.0 mm (5.20 in)
XVS11AWX 132.0 mm (5.20 in)
XVS11AWXC 132.0 mm (5.20 in)
XVS11X 136.0 mm (5.35 in)
XVS11XC 136.0 mm (5.35 in)

Front tire:

Type:

XVS11ATX Tubeless
XVS11ATXC Tubeless
XVS11AWX Tubeless
XVS11AWXC Tubeless
XVS11X With tube
XVS11XC With tube

Size:

XVS11ATX 130/90-16M/C 67S
XVS11ATXC 130/90-16M/C 67S
XVS11AWX 130/90-16M/C 67S
XVS11AWXC 130/90-16M/C 67S
XVS11X 110/90-18M/C 61S
XVS11XC 110/90-18M/C 61S

Manufacturer/model:

XVS11ATX DUNLOP/D404F
XVS11ATXC DUNLOP/D404F
XVS11AWX DUNLOP/D404F
XVS11AWXC DUNLOP/D404F
XVS11X DUNLOP/K555F
XVS11XC DUNLOP/K555F

Manufacturer/model:

XVS11ATX BRIDGESTONE/EXEDRA
G703
XVS11ATXC BRIDGESTONE/EXEDRA
G703
XVS11AWX BRIDGESTONE/EXEDRA
G703
XVS11AWXC BRIDGESTONE/EXEDRA
G703
XVS11X BRIDGESTONE/EXEDRA L309
XVS11XC BRIDGESTONE/EXEDRA L309

Rear tire:

Type:

XVS11ATX Tubeless
XVS11ATXC Tubeless
XVS11AWX Tubeless
XVS11AWXC Tubeless
XVS11X With tube
XVS11XC With tube

8

8-2

SPECIFICATIONS

8

Size:

170/80-15M/C 77S

Manufacturer/model:

XVS11ATX DUNLOP/D404G
XVS11ATXC DUNLOP/D404G
XVS11AWX DUNLOP/D404G
XVS11AWXC DUNLOP/D404G
XVS11X DUNLOP/K555
XVS11XC DUNLOP/K555

Manufacturer/model:

XVS11ATX BRIDGESTONE/EXEDRA
G702
XVS11ATXC BRIDGESTONE/EXEDRA
G702
XVS11AWX BRIDGESTONE/EXEDRA
G702
XVS11AWXC BRIDGESTONE/EXEDRA
G702
XVS11X BRIDGESTONE/EXEDRA
G546G
XVS11XC BRIDGESTONE/EXEDRA
G546G

Loading:

Maximum load:

XVS11ATX 203 kg (448 lb)
XVS11ATXC 200 kg (441 lb)
XVS11AWX 203 kg (448 lb)
XVS11AWXC 200 kg (441 lb)
XVS11X 200 kg (441 lb)
XVS11XC 197 kg (434 lb)
(Total weight of ride r, passenger, cargo and
accessories)

Tire air pressure (measured on cold
tires):

Loading condition:

0–90 kg (0–198 lb)
Front:

XVS11ATX 225 kPa (33 psi) (2.25
kgf/cm²)
XVS11ATXC 225 kPa (33 psi) (2.25
kgf/cm²)
XVS11AWX 225 kPa (33 psi) (2.25
kgf/cm²)
XVS11AWXC 225 kPa (33 psi) (2.25
kgf/cm²)
XVS11X 200 kPa (29 psi) (2.00 kgf/cm²)
XVS11XC 200 kPa (29 psi) (2.00
kgf/cm²)

Rear:

XVS11ATX 250 kPa (36 psi) (2.50
kgf/cm²)
XVS11ATXC 250 kPa (36 psi) (2.50
kgf/cm²)
XVS11AWX 250 kPa (36 psi) (2.50
kgf/cm²)
XVS11AWXC 250 kPa (36 psi) (2.50
kgf/cm²)
XVS11X 225 kPa (33 psi) (2.25 kgf/cm²)
XVS11XC 225 kPa (33 psi) (2.25
kgf/cm²)

Loading condition:

XVS11ATX 90–203 kg (198–448 lb)
XVS11ATXC 90–200 kg (198–441 lb)
XVS11AWX 90–203 kg (198–448 lb)

XVS11AWXC 90–200 kg (198–441 lb)
XVS11X 90–200 kg (198–441 lb)
XVS11XC 90–197 kg (198–434 lb)
Front:

225 kPa (33 psi) (2.25 kgf/cm²)

Rear:

250 kPa (36 psi) (2.50 kgf/cm²)

Front wheel:

Wheel type:

XVS11ATX Cast wheel
XVS11ATXC Cast wheel
XVS11AWX Cast wheel
XVS11AWXC Cast wheel
XVS11X Spoke wheel
XVS11XC Spoke wheel

Rim size:

XVS11ATX 16M/C x MT3.00
XVS11ATXC 16M/C x MT3.00
XVS11AWX 16M/C x MT3.00
XVS11AWXC 16M/C x MT3.00
XVS11X 18x2.15
XVS11XC 18x2.15

Rear wheel:

Wheel type:

XVS11ATX Cast wheel
XVS11ATXC Cast wheel
XVS11AWX Cast wheel
XVS11AWXC Cast wheel
XVS11X Spoke wheel
XVS11XC Spoke wheel

Rim size:

15M/C x MT4.50

8-3

SPECIFICATIONS

Front brake:

Type:

Dual disc brake

Operation:

Right hand operation

Recommended fluid:

DOT 4

Rear brake:

Type:

Single disc brake

Operation:

Right foot operation

Recommended fluid:

DOT 4

Front suspension:

Type:

Telescopic fork

Spring/shock absorber type:

Coil spring/oil damper

Wheel travel:

140.0 mm (5.51 in)

Rear suspension:

Type:

Swingarm (link suspension)

Spring/shock absorber type:

Coil spring/gas-oil damper

Wheel travel:

113.0 mm (4.45 in)

Electrical system:

Ignition system:

Transistorized coil ignition (digital)

Charging system:

AC magneto

Battery:

Model:

GT14B-4

Voltage, capacity:

12 V, 12.0 Ah

Headlight:

Bulb type:

Halogen bulb

Bulb voltage, wattage × quantity:

Headlight:

12 V, 60 W/55.0 W × 1

Tail/brake light:

12 V, 8.0 W/27.0 W × 1

Front turn signal/position light:

12 V, 23 W/8.0 W × 2

Rear turn signal light:

12 V, 21.0 W × 2

Meter lighting:

14 V, 1.4 W × 2

Neutral indicator light:

12 V, 1.7 W × 1

High beam indicator light:

12 V, 1.7 W × 1

Oil level warning light:

12 V, 1.7 W × 1

Turn signal indicator light:

12 V, 1.7 W × 1

Engine trouble warning light:

12 V, 1.7 W × 1

Fuses:

Main fuse:

30.0 A

Headlight fuse:

15.0 A

Signaling system fuse:

10.0 A

Ignition fuse:

10.0 A

Carburetor heater fuse:

15.0 A

Ignitor unit fuse:

5.0 A

Backup fuse:

5.0 A

8

8-4

CONSUMER INFORMATION

Identification numbers

Record the key identification number,
vehicle identification number and mod­el label information in the spaces pro­vided below for assistance when
ordering spare parts from a Yamaha
dealer or for reference in case the vehi­cle is stolen.
KEY IDENTIFICATION NUMBER:

VEHICLE IDENTIFICATION
NUMBER:

MODEL LABEL INFORMATION:

9

EAU26351

Key identification number

1. Key identification number 1. Vehicle identification number

The key identification number is
stamped into the key tag. Record this
number in the space provided and use
it for reference when ordering a new
key.

EAU26381

Vehicle identification number

The vehicle identification number is
stamped into the steering head pipe.
Record this number in the space pro­vided.

NOTE:

The vehicle identification number is
used to identify your motorcycle and
may be used to register your motor­cycle with the licensing authority in your
area.

EAU26400

9-1

CONSUMER INFORMATION

Model label

EAU26470

1. Model label

The model label is affixed to the frame
under the rider seat. (See page 3-9.)
Record the information on this label in
the space provided. This information
will be needed when ordering spare
parts from a Yamaha dealer.

9

9-2

CONSUMER INFORMATION

Reporting safety defects

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately
inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Yamaha Motor Corporation,
U.S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group
of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems
between you, your dealer, or Yamaha Motor Corporation, U.S.A.
To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to
http://www.safercar.gov; or write to: Administrator, NHTSA, 400 Seventh Street, SW., Washington, DC 20590. You can also
obtain other information about motor vehicle safety from http://www.safercar.gov.

9

EAU26551

9-3

CONSUMER INFORMATION

EAU26560

Motorcycle noise regulation

TAMPERING WITH NOISE CONTROL SYSTEM PROHIBITED:

Federal law prohibits the following acts or the causing thereof: (1) The removal or rendering inoperative by any person other
than for purposes of maintenance, repair, or replacement of any device or element of design incorporated into any new ve­hicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use or (2) the use of
the vehicle after such device or element of design has been removed or rendered inoperative by any person.
“AMONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACTS LISTED BELOW”.
These acts include tampering with the following systems; i.e., modification, removal, etc.

Exhaust system

• Muffler

• Exhaust pipe

• Silencer

Intake system

• Air cleaner case

• Air cleaner element

• Intake duct

9

9-4

CONSUMER INFORMATION

Maintenance record

Copies of work orders and/or receipts for parts purchased and installed on your vehicle will be required to document that
maintenance has been completed in accordance with the emissions warranty. The chart below is printed only as a reminder
that maintenance work is required. It is not acceptable proof of maintenance work.

Maintenance

interval

600 mi

(1000 km) or

1 month
4000 mi

(7000 km) or

6 months

8000 mi

(13000 km) or

12 months

12000 mi

(19000 km) or

18 months

16000 mi

(25000 km) or

24 months

20000 mi

(31000 km) or

30 months

9

24000 mi

(37000 km) or

36 months

28000 mi

(43000 km) or

42 months

32000 mi

(49000 km) or

48 months

Date of
service

Mileage

Servicing dealer

name and address

Remarks

EAU26632

9-5

CONSUMER INFORMATION

Maintenance

interval

36000 mi

(55000 km) or

54 months

40000 mi

(61000 km) or

60 months

Date of
service

Mileage

Servicing dealer

name and address

Remarks

9

9-6

CONSUMER INFORMATION

YAMAHA MOTOR CORPORATION, U.S.A. STREET AND ENDURO MOTORCYCLE LIMITED
WARRANTY

Yamaha Motor Corporation, U.S.A. hereby warrants that
new Yamaha motorcycles will be free from defects in
material and workmanship for the period of time stated
herein, subject to certain stated limitations.

THE PERIOD OF WARRANTY for Yamaha motorcycles
originally equipped with headlight, stoplight, and turn
signals shall be one (1) year from the date of purchase,
with no mileage limitation.

MODELS EXCLUDED FROM WARRANTY include
those used for non-Yamaha-authorized renting, leasing
or other commercial purposes, and TZ models.

DURING THE PERIOD OF WARRANTY, any authorized
Yamaha motorcycle dealer will, free of charge, repair or
replace any part adjudged defective by Yamaha due to
faulty workmanship or material from the factory. Parts used
in warranty repairs will be warranted for the balance of the
product’s warranty period. All par ts replaced under
warranty become property of Yamaha Motor Corporation,
U.S.A.

GENERAL EXCLUSIONS from this warranty shall
include any failures caused by:

Competition or racing use.

a)

Installation of parts or accessories that are not

b)

qualitatively equivalent to genuine Yamaha parts.
Abnormal strain, neglect, or abuse.

c)

Lack of proper maintenance.

d)

Accident or collision damage.

e)

Modification to original parts.

f)

9

SPECIFIC EXCLUSIONS from this warranty shall

include parts replaced due to normal wear or routine
maintenance.

THE CUSTOMER’S RESPONSIBILITY under this
warranty shall be to:

1.

Operate and maintain the motorcycle as specified in
the appropriate Owner’s Manual, and

2.

Give notice to an authorized Yamaha motorcycle
dealer of any and all apparent defects within ten (10)
days after discovery, and make the machine available
at that time for inspection and repairs at such dealer’s
place of business.

WARRANTY TRANSFER: To transfer the warranty from
the original purchaser to any subsequent purchaser, it is
imperative that the machine be inspected and registered
for warranty by an authorized Yamaha motorcycle dealer.
In order for this warranty to remain in effect, this
inspection and registration must take place within ten
(10) days after transfer. An inspection and registration fee
will be charged for this service.

EMISSION CONTROL SYSTEM WARRANTY:

Yamaha Motor Corporation, U.S.A. also warrants to the
ultimate purchaser and each subsequent purchaser of
each Yamaha motorcycle covered by this warranty with a
displacement of 50cc or greater, that the vehicle is
designed, built, and equipped so as to conform at the
time of sale with all U.S. emissions standards applicable
at the time of manufacture and that it is free from defects
in materials and workmanship which would cause it not
to meet these standards within the period listed
immediately below. Failures other than those resulting
from defects in material or workmanship, which arise
solely as a result of owner abuse and/or lack of proper
maintenance, are not covered by this warranty.

Engine
Displacement

Under 50cc

50cc to 169cc

170cc to 279cc

280cc and over

YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO
OTHER WARRANTY OF ANY KIND, EXPRESSED OR
IMPLIED. ALL IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WHICH EXCEED THE
OBLIGATIONS AND TIME LIMITS STATED IN THIS
WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA
MOTOR CORPORATION, U.S.A. AND EXCLUDED
FROM THIS WARRANTY.

SOME STATES DO NOT ALLOW LIMITATIONS ON
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE
ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO
EXCLUDED FROM THIS WARRANTY ARE ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING LOSS OF USE. SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL
RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.

or five years, whichever occurs first

or five years whichever occurs first

18,000 km (11,185 miles)

or five years, whichever occurs first

30,000 km (18,641 miles)

or five years, whichever occurs first

YAMAHA MOTOR CORPORATION, U.S.A.

Cypress, California 90630

EAU26663

6,000 km (3,750 miles)

12,000 km (7,465 miles)

Period

P.O. Box 6555

9-7

CONSUMER INFORMATION

WARRANTY QUESTIONS AND ANSWERS

Q.

What costs are my responsibility during the warranty period?

A.

The customer’s responsibility includes all costs of normal maintenance services,
non-warranty repairs, accident and collision damages, and oil, oil filters, air filters,
spark plugs, and brake shoes.

Q.

What are some examples of “abnormal” strain, neglect, or abuse?

A.

These terms are general and overlap each other in areas. Specific examples
include: Running the machine out of oil, sustained high rpm, full-throttle, operating
the machine with a broken or damaged part which causes another part to fail,
damage or failure due to improper or careless transportation and/or tie-down. If
you have any specific questions on operation or maintenance, please contact your
dealer for advice.

Q.

Does the warranty cover incidental costs such as towing or transportation due to
a failure?

A.

No. The warranty is limited to repair of the machine itself.

Q.

May I perform any or all of the recommended maintenance shown in the Owner’s
Manual instead of having the dealer do them?

A.

Yes, if you are a qualified mechanic and follow the procedures specified in the
Owner’s and Service Manual. We do recommend, however, that items requiring
special tools or equipment be done by a Yamaha motorcycle dealer.

Q.

Will the warranty be void or cancelled if I do not operate or maintain my new
motorcycle exactly as specified in the Owner’s Manual?

A.

No. The warranty on a new motorcycle cannot be “voided” or “cancelled.” However,

if a particular failure is caused by operation or maintenance other than as
described in the Owner’s Manual, that failure may not be covered under
warranty.

Q.

What responsibility does my dealer have under this warranty?

A.

Each Yamaha motorcycle dealer is expected to:

1.

Completely set up every new machine before sale.

2.

Explain the operation, maintenance, and warranty requirements to your
satisfaction at the time of sale, and upon your request at any later date.

3.

Each Yamaha motorcycle dealer is held responsible for his setup, service and
warranty repair work.

Q.

Is the warranty transferable to second owners?

A.

Yes. The remainder of the existing warranty can be transferred upon request. The
unit has to be inspected and re-registered by an authorized Yamaha motorcycle
dealer for the policy to remain effective.

CUSTOMER SERVICE

If your machine requires warranty service, you must take it to any authorized Yamaha
motorcycle dealer within the continental United States. Be sure to bring your warranty
registration card or other valid proof of the original date of purchase. If a question or
problem arises regarding the warranty, first contact the owner of the dealership. Since
all warranty matters are handled at the dealer level, this person is in the best position to
help you. IF you are still not satisfied and require additional assistance, please write to:

YAMAHA MOTOR CORPORATION, U.S.A.

CUSTOMER RELATIONS DEPARTMENT

When contacting Yamaha Motor Corporation, U.S.A., don’t forget to include any
important information such as names, addresses, model, V.I.N. (frame number),
dates, and receipts.

The federal government requires each manufacturer of a motor vehicle to maintain a
complete, up-to-date list of all first purchasers against the possibility of a safety­related defect and recall. This list is compiled from the purchase registrations sent to
Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.

If you should move after you have purchased your new motorcycle, please advise us
of your new address by sending a postcard listing your motorcycle model name, V.I.N.
(frame number), dealer number (or dealer’s name) as it is shown on your warranty
card, your name and new mailing address. Mail to:

YAMAHA MOTOR CORPORATION, U.S.A.

This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration
record in accordance with federal law.

P.O. Box 6555

Cypress, California 90630

CHANGE OF ADDRESS

P.O. Box 6555

Cypress, California 90630

Attention: Warranty Department

9

9-8

CONSUMER INFORMATION

YAMAHA EXTENDED SERVICE (Y.E.S.)

EAU26750

Keep your Yamaha protected even after your warranty
expires with genuine Yamaha Extended Service (Y.E.S.).

Y.E.S. is designed and administered by Yamaha Motor
Corporation to provide maximum owner satisfaction. You
get uninterrupted factory-backed coverage for extra
peace of mind.

Y.E.S. is flexible. You choose the plan that’s right for
you: 12 months, 24 months, 36 months or, on certain
models, even 48 months beyond your warranty period.

Y.E.S. is designed and administered by the same
Yamaha people who handle your warranty – and it
shows in the comprehensive coverage benefits. There
are no mileage limitations. Coverage isn’t limited to
“moving parts” or the “drive train” like many other plans.
And Y.E.S. covers manufacturing defects just like the
warranty. See the sample contract at your Yamaha
dealer to see how comforting uninterrupted factory­backed protection can be.

You don’t have to pay anything for covered repairs.
There’s no deductible to pay, and repairs aren’t
“pro-rated.” You don’t have any “out-of-pocket” expenses
for covered repairs.

In addition, Travel and Recreation Interruption Protection
(TRIP) is included at no extra cost. TRIP gives you up to
$150 reimbursement per occurrence for any reasonable
expenses you incur because your Yamaha needs
covered service: replacement vehicle rental, emergency
towing, phone calls, even food and lodging when you are
away from home. This superb coverage goes into effect
when you purchase Y.E.S., so it applies to any warranty
repairs as well as covered repairs during your entire
Y.E.S. plan period.

Y.E.S. coverage is honored at any authorized Yamaha
dealer nationwide.

Y.E.S. coverage is transferable to a new owner if you
sell or trade-in. That can make your Yamaha much more
valuable!

This excellent Y.E.S. plan coverage is only available to
Yamaha owners like you, and only while your Yamaha is still
within the Yamaha Limited Warranty period. So visit your
authorized Yamaha dealer to get all the facts. He can show
you how easy it is to protect your investment with Yamaha
Extended Service.

9

9-9

We urge you to act now. You’ll get the excellent benefits of
TRIP coverage right away, and you’ll rest easy knowing
you’ll have strong factory-backed protection even after your
Yamaha Limited Warranty expires.

A special note:
If visiting your dealer isn’t convenient, contact Yamaha with
your Primary ID number (your frame number). We’ll be
happy to help you get the Y.E.S. coverage you need.

Yamaha Service Marketing
P.O. Box 6555
Cypress, CA 90630
1-(866)-YES-EXTD (1-866-937-3983)

CONSUMER INFORMATION

9

9-10

INDEX

A

Accessories and replacement parts ...... 6-21

Air filter element, cleaning..................... 6-13

B

Battery................................................... 6-30

Brake and clutch levers,

checking and lubricating ..................... 6-27

Brake and shift pedals,

checking and lubricating ..................... 6-26

Brake fluid, changing ............................6-25

Brake fluid level, checking .................... 6-24

Brake lever.............................................. 3-5

Brake lever free play, adjusting............. 6-22

Brake pedal............................................. 3-6

C

Cables, checking and lubricating ..........6-26

Canister (for California only) .................6-10

Carburetors...........................................6-14

Care ........................................................7-1

Catalytic converter ..................................3-8

Clutch lever.............................................3-4

Clutch lever free play, adjusting............ 6-22

D

Dimmer switch ........................................ 3-4

E

Engine break-in....................................... 5-4

Engine idling speed, checking ..............6-14

Engine oil.............................................. 6-10

Engine, starting a warm .......................... 5-2

Engine stop switch ..................................3-4

Engine trouble warning light....................3-2

F

Final gear oil .........................................6-12

Front and rear brake pads, checking ....6-24

Front fork, checking.............................. 6-28

Fuel......................................................... 3-7

Fuel cock ................................................ 3-8

Fuel tank cap.......................................... 3-6

Fuses, replacing ................................... 6-31

H

Handlebar switches ................................ 3-3

Headlight bulb, replacing ...................... 6-33

Helmet holder ....................................... 3-12

High beam indicator light ........................ 3-2

Horn switch............................................. 3-4

I

Identification numbers ............................ 9-1

Ignition circuit cut-off system ................ 3-17

Indicator and warning lights.................... 3-2

K

Key identification number ....................... 9-1

L

Labels, location of................................... 1-5

Luggage strap holders.......................... 3-16

M

Main switch/steering lock........................ 3-1

Maintenance and lubrication, periodic .... 6-4

Maintenance, emission control system... 6-3

Maintenance, periodic ............................ 6-1

Maintenance record................................ 9-5

Matte color, caution ................................ 7-1

Model label ............................................. 9-2

N

Neutral indicator light.............................. 3-2

Noise regulation...................................... 9-4

O

Oil level warning light.............................. 3-2

P

Panel, removing and installing ................6-8

Parking....................................................5-5

Part locations ..........................................2-1

Pre-operation check list...........................4-2

R

Rear brake light switch, adjusting .........6-23

Rear suspension, lubricating................. 6-28

S

Safety defects, reporting .........................9-3

Safety information...................................1-1

Seats (XVS11AWX/XVS11ATX) ...........3-11

Seats (XVS11X)......................................3-9

Shifting ....................................................5-3

Shift pedal (XVS11AWX/XVS11ATX) .....3-5

Shift pedal (XVS11X) ..............................3-5

Shock absorber assembly, adjusting .... 3-14

Sidestand ..............................................3-16

Sidestand, checking and lubricating...... 6-27

Spark plugs, checking .............................6-8

Specifications..........................................8-1

Speedometer unit.................................... 3-3

Starter (choke) lever................................3-9

Starting and warming up a cold engine... 5-1

Start switch..............................................3-4

Steering, checking.................................6-29

Storage....................................................7-3

Storage compartment............................ 3-13

Supporting the motorcycle ....................6-35

Swingarm pivots, lubricating .................6-28

T

Throttle cable free play, checking .........6-15

Throttle grip and cable,

checking and lubricating .....................6-26