Yamaha SPS-10MM User Manual

SPEAKER STAND

618–868 (24-5/16”–34-3/16”)

282

(11-1/8”)

(2-1/2”)

(13/16”)

(3-3/16”)

300

(11-13/16”)

300

(11-13/16”)

(2-3/8”)

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VÄSTRA FRÖLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

Read this before use

Thank you for selecting the Yamaha SPS-10MM speaker stand.

SPS-10MM

PRECAUTIONS

ASSEMBLY

INSTRUCTIONS

● This speaker stand is only for the speaker systems

listed in “USABLE SPEAKERS” below. Do not use the speakers other than these listed.

● To prevent the speaker from falling, use the screws

and parts provided with the stand.

● To prevent the speaker stand from falling over, select

a location which is flat and stable.

● To avoid accidents resulting from tripping over loose

speaker cables and to prevent the speaker stand from falling over, fix the speaker cables to the wall, etc.

● Do not let the children lean on the stand as this might

cause the serious accidents resulting from the falling over of the speaker stand.

 DIMENSIONS (mm/inch)

Top view

● To prevent the speaker stand from discoloring and

warping, keep the speaker stand away from the stoves and places where it will be exposed to direct sunlight, etc.

● Do not attempt to clean the speaker stand with

chemical solvents as this might damage the finish. Use a clean, dry cloth.

● Secure placement or installation is the owner’s

responsibility. YAMAHA shall not be liable for any accident caused by improper placement or installation of speakers.

 SPECIFICATIONS

Dimensions (W x H x D) : 300 x 618 – 868 x 300mm

(11-13/16” x 24-5/16

– 34-3/16” x 11-13/16”)

Weight : 1.6 kg (3 lbs. 8 oz.)

 USABLE SPEAKERS

● NS-10MM

Front view

● NS-10MMT

● NX-220P

(the main and rear speakers included in the NS-P220 speaker package)

● NS-E104

(the rear speakers included in the NS-P320 speaker package)

● NS-E114

(the rear speakers included in the NS-P326 speaker package)

● NX-S100S

(the front and rear speakers included in the DVX-S100 sound system)

Printed in Japan V816800-1

 ASSEMBLY PROCEDURES

Before beginning assembly, check the parts list and make sure all the parts are included.

ASSEMBLY FIGURE

●

Plate

Pole

Limit of the stand height

Support

Speaker

Speaker cable

PARTS LIST

●

NAME PARTS NOS.

QUANTITY

1 + self-binding tapping screws EP040090 12

(4 x 12)

2 Hexagon socket set screws VV249400 7 3 + self-binding screws (4 x 8) EG340360 4 4 Pads VV249200 8 5 Wrench (hexagonal) VV249500 1 6 Gaskets VV249300 4

ASSEMBLY PROCEDURES

●

(You will need a screwdriver for assembly.)

1. Attaching the base and support.

Pass the support through the hole from the bottom of the base, and fasten the + self-binding tapping screws

●

Fix the support so that the holes for the screws comes to the rear side.

●

Do not overtighten the + self-binding tapping screws 1. Doing so may damage the screws or assembly.

2. Attaching the pole and support.

Insert the pole to the support, and fasten the hexagon socket set screws 2 into the three hole on the support using the included wrench 5.

●

The line on the pole shows the limit of the stand height. Do not use the stand pulling out the pole above from this line. The hexagon socket set screw 2 of the lower side becomes ineffective and the fixation becomes unstable.

Base

3. Attaching the pads.

Put the pads 4 to the four corners on the bottom of the base to prevent the stand from moving rickety.

Attaching the gaskets.

Put the gaskets 6 to the both side of the plate.

Wiring the speaker cables.

Insert the speaker cables to the hole on the plate, and aligned them to the grooved part on the bottom of the base.

6. Attaching the speakers.

Line up the holes on the bottom of the speaker and the center hole on the plate, and fasten the + binding screws 3.

●

In order to ensure that the speakers do not fall, always hold the speakers while attaching the speakers.