INDEX)
LCD screen
Delete button (DEL)
Pause/Record button (PAUSE/REC)
Menu/Stop button (MENU/STOP)
Speaker
Headphones socket ()
Power/Hold switch (POWER/HOLD)
Playback speed control switch (PLAY SPEED)
Battery compartment lid
USB terminal slide switch
USB terminal cover (may be rotated)
USB terminal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
10
11
12
13
1
1
2
9
20
3
4
5
6
7
8
13
14
14
15
16
17
18
19
LCD screen
Repeat/Random/5-second replay (ONE, ALL, RND,
5SEC)
2
Battery indicator
3
Battery setting (e: eneloop, A: Alkaline)
4
Recording mode (XHQ, HQ, SP, LP, PCM)
5
VAS (Voice activated system)
6
Microphone sensitivity
7
External recording mode (MIC, LINE)
8
Playback Lock/Release
9
Timer/Alarm
10
File number
11
Total file number
12
Information display (Time/Message/Mode etc.)
Security setting On/Off (S folder only)
Folder (A, B, C, D, S, L, M)
1
2345678 9
14
13
10
11
12
4
POCKETRAK 2G Reference Manual
Starting Up
Adjusting the direction of the built-in microphones
(Tilt up)
You can adjust the direction of the built-in microphones. For example, if you place the unit on a
table to record, you can tilt the mic up to avoid noise from the table top. Adjust the direction of
the mic to suit the recording circumstances.
Note:
· Do not adjust the microphone angle during recording. Otherwise, undesirable handling
noise will be recorded.
Inserting a battery
Turn the power off before you replace the battery.
Note:
· If you use an alkaline battery, press and hold down the MENU/STOP button for at least
two seconds to access the COMMON menu, then select “ALKALINE” for the BATTERY
SETTING (page 33).
Install one eneloop (supplied) or
AAA/LR03/HP16 alkaline battery.
Battery indicator
Check the battery indicator on the LCD screen to determine the remaining battery power.
: Good condition
:Weak battery
: Exhausted battery: Recharge the “eneloop” (page 38) or replace the
battery with a new alkaline battery. If you keep using the recorder
without recharging the “eneloop” or replacing the battery, the
recorder will display the message “LOW BATTERY PLEASE CHARGE A
BATTERY” or “LOW BATTERY.” The LCD screen will then go dark.
POCKETRAK 2G Reference Manual
5
Basic Operations
Basic Operations
Selecting a menu item
Press and hold down the MENU/STOP button for at least two seconds.
Press the Y or T button: Moves the cursor highlight up/down.
Press the W button: Selects the menu item.
Canceling the operation or return to the previous display
Press the MENU/STOP button: Returns to the previous display.
Using the headphones
Connect the headphones to the socket. The speaker will be disconnected automatically.
Using an external stereo microphone
Connect an external stereo microphone (not supplied) to the socket (page 16).
The built-in microphones are automatically disconnected.
Note:
· If you use an external stereo microphone, press and hold down the MENU/STOP button
for at least two seconds to access the VOICE menu, then select “MIC” for the REC
SELECT.
Turning the power on or off
Set the POWER/HOLD switch to the right.
“HELLO!” appears briefly on the display and the
power turns on, and then the last selected file number appears (Resume function).
Set the POWER/HOLD switch to the left. “SEE
YOU!” appears on the display and the power turns off.
Auto power off function
• If you leave the unit turned on for 15 minutes without using it, the unit will automatically turn off.
• If you leave the unit turned on with a recording paused for more than 15 minutes,
the unit will turn off the power after it creates the recorded file.
6
POCKETRAK 2G Reference Manual
Basic Operations
Hold function
The Hold function can help you to avoid stopping operation (playback or recording) by accidentally pressing a button.
Set the POWER/HOLD switch to the left while the unit is operating.
The Hold function is engaged.
• If an operation button is pressed while the Hold function is
engaged, “HOLD ON” will appear on the display and nothing
else will happen.
Set the POWER/HOLD switch to the right.
“HOLD OFF” appears on the display and the Hold function is disengaged.
• If operation (playback or recording) is finished while the Hold function is engaged,
the unit automatically shuts down.
Adjusting the volume
Press the VOL + or – button.
The volume level appears on the display (VOLUME 0 to VOLUME 20).
Date and time settings
1. While the recorder is stopped, press the MENU/STOP button for
at least two seconds.
2. Press the Y or T button to select “COMMON”, then
press the W button.
3. Press the Y or T button to select “DATE & TIME”, then
press the W button.
4. Press the Y or T button to select the year, then press
the W button.
5. In the same way, set the month, day, 24H or AM/PM (12H)
display, hour and minute.
POCKETRAK 2G Reference Manual 7
Basic Operations
6. Press the MENU/STOP button twice to exit from the menu setting mode.
The date and time settings are complete.
Note:
· Calendar settings may be lost if the battery is removed for longer than 10 minutes. If
so, reset the calendar settings.
· The time display might become slightly inaccurate if the unit is used for an extended
period of time. If this happens, reset the calendar settings.
8 POCKETRAK 2G Reference Manual
Recording
Recording time
The recording time differs depending on the recording mode, as shown below.
Recording time (approx.)
Recording mode
PCM: Pulse Code Modulation (stereo)2hr. 50 min.10 min.
XHQ: Extra high-quality (stereo)25 hr. 20 min. 2 hr. 15 min.
HQ: High-quality (stereo)63 hr. 20 min. 4 hr. 35 min.
SP: Standard (stereo)126 hr.9 hr. 15 min.
LP: Long (monaural)253 hr.18 hr. 30 min.
PUBLIC AREA
(A, B, C and D folder)
SECURITY AREA
(S folder)
Recording
Selecting the recording mode
Make sure that the battery has sufficient power to record.
1. While the recorder is stopped, press the MENU/STOP button for
at least two seconds.
2. Press the Y or T button to select “VOICE”, then press the W
button.
3. Press the Y or T button to select “REC MODE”, then
press the W button.
4. Press the Y or T button to select a recording mode, then press the W but-
ton. The display indicates “REC MODE”.
Extra high-quality
High-qualityStandardLong
Pulse Code
Modulation
5. Press the MENU/STOP button twice to exit from the menu setting mode.
The recording mode setting is complete.
Note:
· If you record and delete files quite frequently, there is a chance that the unit may eventually skip while recording in PCM mode. To avoid such skipping, save desired recordings to your computer, then reformat the recorder’s internal memory.
POCKETRAK 2G Reference Manual 9
Recording
Starting recording
Do not remove the battery during recording.
You can adjust the direction of the built-in microphones to suit your recording situation (page 5).
1. Press the FOLDER/INDEX button to select a folder (A, B, C, D or S).
Hint:
The A, B, C, D and S folders store audio files (such as a conversation, for example)
recorded via the recorder’s microphones. The L folder stores music recorded from a connected external device, such as a CD player. The M folder stores music files transferred
from a computer.
For detailed explanation of the folders, refer to page 41.
Note:
· Press and hold down the FOLDER/INDEX button for at least two seconds to select the S
folder.
· Do not select the L or M folder. The L and M folders are not VOICE folders. If you select
one of them, built-in microphone recordings will be recorded automatically to the A
folder. However, if the A folder is full, no additional built-in microphone recordings are
possible (until you delete some recordings).
· The unit can record up to 99 files in any one folder (A, B, C, D or S). “FILE FULL”
appears if you attempt to record a 100th file in any folder.
2. Press the PAUSE/REC button.
The recording LED lights up and recording starts.
File number
Elapsed recording time
Total file number
Remaining recording time
Note:
· When MIC ALC is set to OFF, the recorder enters the recording standby mode. Press the
PAUSE/REC button again to start recording.
·With some files, the elapsed recording time displayed on the LCD may differ from the
actual elapsed time.
10 POCKETRAK 2G Reference Manual
Recording
Hint:
The recording LED can be turned off (page 33).
You can monitor audio that is currently being recorded by listening through headphones
(supplied) that you connect to the unit. Use the VOL + or – button to adjust the monitoring level.
Stopping recording
Press the MENU/STOP button.
Pausing recording
Press the PAUSE/REC button.
Press it again to resume recording.
Inserting index marks
You can insert index marks only in the files in the VOICE folder.
To insert an index mark, press the FOLDER/INDEX button during recording.
“INDEX SETTING 1/32” appears briefly and recording continues.
Note:
·You can insert up to 32 index marks in each file. If you try to enter additional index
marks, “INDEX FULL” appears briefly on the display. You can delete all index marks as
a group, but you cannot delete individual index marks.
Hint:
You can insert index marks also during playback. To insert an index mark, press the
FOLDER/INDEX button during playback. “INDEX SETTING 1/32” appears briefly and
playback continues.
POCKETRAK 2G Reference Manual 11
Recording
Setting the Auto Level Control (MIC ALC)
About Auto Level Control (MIC ALC)
Auto Level Control is a function that automatically maintains the recording volume
close to a specified level during recording under various recording environments. The
function maintains a consistent recording level by recording loud sounds at lower levels and quiet sounds at higher levels. As a result, files recorded with this function will
play at a comfortable level, with no clipping noise or distortion.
Scenarios for the MIC ALC function
MIC ALCScenariosFeatures
ON
OFF
Recording meetings, conversations, interviews
Recording music practices; recording
sound sources so that playback retains relative source levels as heard in the recording environment
You can make recordings that are less
dynamic but maintain consistent sound
levels for various voices or sources.
You can adjust and optimize the recording level to make recordings that accurately represent to the original sound.
1. While the recorder is stopped, press the MENU/STOP button for at least two
(2) seconds.
2. Press the Y or T button to select “VOICE”, then press the W button.
3. Press the Y or T button to select “MIC ALC”, then press
the W button.
4. Press the Y or T button to select “ON” or “OFF”, then
press the W button.
5. Press the MENU/STOP button twice to exit from the menu setting mode.
The MIC ALC setting is complete.
Note:
· If you change the MIC ALC setting, the icon displayed in the LCD screen changes as
below.
With MIC ALC on:
With MIC ALC off:
12 POCKETRAK 2G Reference Manual
Selecting the microphone sensitivity
With MIC ALC “ON”:
1. While the recorder is stopped, press the MENU/STOP button for at least two
(2) seconds.
2. Press the Y or T button to select “VOICE”, then press the W button.
3. Press the Y or T button to select “MIC SENS.”, then
press the W button.
4. Press the Y or Tbutton to select “HIGH”, “MIDDLE” or
“LOW”, then press the W button.
HIGH: High sensitivity
MIDDLE: Middle sensitivity
LOW: Low sensitivity
Recording
5. Press the MENU/STOP button twice to exit from the menu setting mode.
The setting of the microphone sensitivity is complete.
6. Press the PAUSE/REC button to start recording.
With MIC ALC “OFF”:
1. Press the PAUSE/REC button to enter the recording
standby mode.
Adjust the angle of the built-in microphones toward the
sound to be recorded.
2. Press the Y or Tbutton to adjust the microphone sensi-
tivity while checking the level meter.
The microphone sensitivity can be adjusted to 31 levels (Level
0 to level 30).
SP 20 MIC
SP 15 MIC
3. Press the PAUSE/REC button to start recording.
Note:
· The LCD screen changes while you adjust the microphone sensitivity as shown below.
SP 20 MICSP 20 MICSP 15 MIC
· The recorder will remember the specified microphone sensitivity for the next recording
session.
· Adjusting the microphone sensitivity during recording may cause unwanted noise to be
recorded. Adjust the sensitivity only when the recorder is in recording standby mode.
POCKETRAK 2G Reference Manual 13
Recording
Adjusting the microphone sensitivity
The level meter moves to left or right as the volume level of the sound source
changes.
If the sensitivity level is low:
SP 15 MIC
If the level meter moves only very slightly, raise the microphone sensitivity by pressing the Y button so that the
level meter will move moderatley to the right.
If the sensitivity level is high:
SP 23 MIC
If the level meter frequently moves all the way to the right
and the REC/PEAK LED lights up, recorded sounds may be
distorted. Press the T button to lower the microphone
sensitivity.
If the sensitivity level is optimum:
SP 23 MIC
The microphone sensitivity is optimum when the meter indicates
a “-6” level consistently, without deflecting all the way to the
right at loud sounds.
Note:
·You cannot change the microphone sensitivity setting while the recorder is stopped.
· At a level of zero (0), the recording will be silent.
·Turn on the MIC ALC function when you record any sound source other than music.
14 POCKETRAK 2G Reference Manual
Recording
VAS (Voice Activated System) recording
When the VAS recording function is turned on, and if the unit is in recording pause mode, the
unit will automatically start to record as soon as it detects audio at a level above a certain threshold.
The unit will pause recording when the detected audio level falls below the threshold.
Note:
·VAS recording is available only when MIC ALC is set to ON.
1. While the recorder is stopped, press the MENU/STOP button for at least two
(2) seconds.
2. Press the Y or T button to select “VOICE”, then press the W button.
3. Press the Y or T button to select “VAS”, then press the
W button.
4. Press the Y or T button to select “ON”, then press the
W button.
5. Press the MENU/STOP button twice to exit from the menu setting mode.
6. Press the PAUSE/REC button.
Recording begins automatically when the unit detects audio.
Note:
·You can set the voice sensing level by pressing the Y or T button during recording.
The recorder displays the sensing level (“VAS” 1: Low – “VAS” 5: High).
· Set this function to OFF if you are recording important material. Otherwise, if the source
audio level is too low, the unit will not detect the audio and will not start recording.
POCKETRAK 2G Reference Manual 15
Recording
Recording from external audio devices
1. Use an audio cable to connect the stereo microphone socket ( socket) to
the headphones socket on the external autio device.
To stereo microphone
socket
Audio device
To audio output
headphones socket
Note:
· For audio cable, use a 3.5mm stereo mini plug without resistance.
To LINE OUT (Recording)
or
socket
2. While the recorder is stopped, press the MENU/STOP button for at least 2
seconds.
3. Press the Y or T button to select “VOICE”, then press the W button.
4. Press the Y or T button to select “REC SELECT”, then
press the W button.
5. Press the Y or Tbutton to select “LINE”, then press the
W button.
Note:
· If you record audio with an external stereo microphone, select “MIC” (page 6). For
external microphones, Yamaha recommends that you use an electret condenser microphone with the capabilities of plug-in power operation, 2k Ω impedance, performance
guaranteed with a 1.3V power supply, and a 3.5mm stereo mini plug.
6. Press the MENU/STOP button twice to quit the menu setting mode.
7. Press the FOLDER/INDEX button to select the L (Line)
folder.
Even if one of the other folders is selected, audio data will be
recorded in the L folder.
8. Start playback on the external device, then press the
PAUSE/REC button on the recorder to start recording.
16 POCKETRAK 2G Reference Manual
Note:
· Audio is automatically recorded in XHQ mode.
· The unit can record up to 199 files in the L (Line) folder. If you attempt to record the
200th file, the recorder will indicate “FILE FULL”.
· When you record to the L folder, MIC ALC is automatically set to OFF.
Auto Divide function
When the Auto Divide function is turned on, the unit automatically detects the
silence between songs and records each song as an individual file. This function is
useful when you are recording songs from a CD player.
1. While the recorder is stopped, press the MENU/STOP button for at least 2
seconds.
2. Press the Y or T button to select “VOICE”, then press the W button.
3. Press the Y or T button to select “AUTO DIVIDE”, then
press the W button.
Recording
4. Press the Y or T button to select “ON”, then press the
W button.
5. Press the MENU/STOP button twice to quit the menu setting mode.
Note:
· The function does not work if the recorder does not recognize a silent pause of at least
two seconds between songs, especially when it is recording audio from a cassette tape,
radio, and so on.
· If the unit detects a silent pause for 15 seconds or more, recording stops automatically.
POCKETRAK 2G Reference Manual 17
Loading...
+ 37 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.