Yamaha PF-500 Installation Guide

Accessory CD-ROM

Installation Guide/Installationshandbuch/

Manuel d’installation/Guía de instalación

PF-500

SPECIAL NOTICES

• The software and this Installation Guide are exclusive copyrights of Yamaha Corporation.

• Use of the software and this guide is governed by the SOFTWARE LICENSING AGREEMENT which the purchaser fully agrees to upon breaking the seal of the software packaging. (Please read carefully the AGREEMENT at the end of this guide before installing the application.)

• Copying of the software or reproduction of this guide in whole or in part by any means is expressly forbidden without the written consent of the manufacturer.

• Yamaha makes no representations or warranties with regard to the use of the software and documentation and cannot be held responsible for the results of the use of this guide and the software.

• This disc is a CD-ROM. Do not attempt to play the disc on an audio CD player. Doing so may result in irreparable damage to your audio CD player.

• Copying of the commercially available music data is strictly prohibited except for your personal use.

• The company names and product names in this Installation Guide are the trademarks or registered trademarks of their respective companies.

• Future upgrades of application and system software and any changes in speciﬁcations and functions will be announced separately.

• Depending on the version of your operating system, the screen shots and messages shown in this guide may differ to those that you see on your computer screen.

English

DeutschFrançaisEspañol

BESONDERE HINWEISE

• Dieses Programm und diese Installationsanleitung sind im Sinne des Urheberrechts alleiniges Eigentum der Yamaha Corporation.

• Die Benutzung des Programms und dieser Anleitung unterliegt der SOFTWARE-LIZENZVEREINBARUNG, mit der sich der Erwerber durch Öffnen des Siegels der Programmverpackung uneingeschränkt einverstanden erklärt. (Bitte lesen Sie die VEREINBARUNG am Ende dieser Anleitung vor Installation der Anwendung sorgfältig durch.)

• Das Kopieren der Software und die Reproduktion dieser Anleitung, in welcher Form auch immer, in Teilen oder als Ganzes, sind nur mit schriftlicher Genehmigung des Herstellers erlaubt und sonst ausdrücklich verboten.

• Yamaha leistet keinerlei Garantie hinsichtlich der Benutzung des Programms und der zugehörigen Dokumentation und übernimmt keine Verantwortung für die Ergebnisse der Benutzung dieser Anleitung oder des Programms.

• Bei dieser CD handelt es sich um eine CD-ROM. Versuchen Sie bitte nicht, diese CD-ROM auf einem Audio-CD-Player abzuspielen, da dies zu irreparablen Schäden am Audio-CD-Player führen kann.

• Das Kopieren im Handel erhältlicher Musikdaten ist nur für Ihren Privatgebrauch zulässig und sonst streng untersagt.

• Die in dieser Installationsanleitung erwähnten Firmen- und Produktnamen sind Warenzeichen bzw. eingetragene Warenzeichen der betreffenden Firmen.

• Zukünftige Aktualisierungen von Anwendungs- und Systemsoftware sowie jede Änderung der technischen Daten und Funktionen werden separat bekanntgegeben.

• Je nach der Version Ihres Betriebssystems unterscheiden sich die hier dargestellten Screenshots und Meldungen von der tatsächlichen Anzeige auf Ihrem Computermonitor.

REMARQUES PARTICULIERES

• Les droits d’auteurs (copyright) de ce logiciel et de ce manuel d’installation appartiennent exclusivement à Yamaha Corporation.

• L’usage de ce logiciel et de ce manuel est déﬁni par l’accord de licence auquel l’acheteur déclare souscrire sans réserve lorsqu’il ouvre le sceau de l’emballage du logiciel. (Veuillez donc lire attentivement l’accord de licence du logiciel situé à la ﬁn de ce manuel avant d’installer le logiciel.)

• Toute copie du logiciel et toute reproduction totale ou partielle de ce manuel, par quel moyen que ce soit, est expressément interdite sans l’autorisation écrite du fabricant.

• Yamaha n’offre aucune garantie en ce qui concerne l’utilisation du logiciel et de la documentation. Yamaha ne peut en aucun cas être tenu responsable des dommages éventuels résultant de l’utilisation de ce manuel et de ce logiciel.

• Ce disque est un CD-ROM. N’essayez donc pas de l’insérer dans un lecteur de CD audio. Vous risqueriez d’endommager ce dernier de manière irréversible.

• Toute copie de données musicales commercialisées est formellement interdite, sauf pour usage personnel.

• Les noms des ﬁrmes et des produits apparaissant dans ce manuel d’installation sont des marques commerciales ou des marques déposées appartenant à leurs détenteurs respectifs.

• Les remises à jour du programme et du système ainsi que toute modiﬁcation des caractéristiques et fonctions seront annoncées séparément.

• En fonction de la version du système d’exploitation que vous utilisez, les captures d’écran et les messages qui ﬁgurent dans ce manuel peuvent différer de ceux qui apparaissent sur l’écran de votre ordinateur.

AVISOS ESPECIALES

• El copyright del software y de la guía de instalación es propiedad exclusiva de Yamaha Corporation.

• La utilización de este software y de esta guía debe ajustarse al CONTRATO PARA USO DE SOFTWARE BAJO LICENCIA, con el que el comprador maniﬁesta su total conformidad al abrir el paquete de software. (Lea detenidamente el CONTRATO que se incluye al ﬁnal de esta guía antes de instalar la aplicación).

• La copia del software o la reproducción total o parcial de este manual por cualquier medio sin la autorización escrita del fabricante está expresamente prohibida.

• Yamaha no asume responsabilidad alguna ni ofrece garantía alguna en relación con el uso del software y de la documentación, y no puede ser declarada responsable de los resultados de la utilización de este manual ni del software.

• Este disco es un CD-ROM. No intente reproducirlo en un reproductor de CD de audio, porque al hacerlo se podrían causar daños irreparables en el reproductor.

• Queda terminantemente prohibida la copia de datos musicales disponibles comercialmente, excepto para uso personal.

• Los nombres de compañías y de productos que aparecen en esta guía de instalación son marcas o marcas registradas de sus respectivas compañías.

• Las futuras actualizaciones de la aplicación y del software del sistema, y cualquier cambio en las especiﬁcaciones y funciones, se anunciarán independientemente.

• Según las versiones del sistema operativo, las capturas de pantalla y los mensajes que aparecen en esta guía podrían diferir de los que aparecen en la pantalla del ordenador .

Accessory CD-ROM Installation Guide (PF-500) 1

→

Important Notices about the CD-ROM

Data Types

This CD-ROM includes application software. Please refer to page 4 (Windows) and 9 (Macintosh) for details about the software and how to install it.

These applications allow you to transfer data between your computer and the PF-500.

English

Operating System (OS)

The applications in this CD-ROM are provided in versions for both Windows and Macintosh operating systems. The installation procedure and the applications themselves differ depending on the operating system that you are using. Please refer to the appropriate installation instructions.

Media format

The PF-500 and the File Utility software are compatible with the MS-DOS format media.

Never attempt to play back the included CD-ROM on an audio CD player. Doing so may result in damage to your hearing as well as to your CD player/audio speakers.

Windows Read page 3, 5, 13. Macintosh Read page 3, 10, 13.

2 Accessory CD-ROM Installation Guide (PF-500)

CD-ROM installation procedure

The following steps are the same for both Windows and Macintosh.

Verify that your system meets the operating requirements of the software (File Utility, driver, etc.) (Windows page 5, Macintosh page 10). Connect the PF-500 to your computer.

Refer to the owner’s manual for details on connections.

n Depending on the computer system you are using, some types of connections may not be possible.

Install the driver appropriate for your type of connection into your computer, and make the necessary settings. The arrow symbols shown below represent cables.

• Connection using a USB cable USB connector of the PF-500 ↔ USB connector of the computer … Windows page 5, Macintosh page 10

• Connection using a serial cable TO HOST connector of the PF-500 ↔ Serial port of the computer (RS-232C or RS-422 connector) … page 7

• Connection using MIDI cables MIDI connector of the PF-500 ← MIDI interface device → Computer … Windows page 5, Macintosh page 10

Install the software (File Utility, etc.) Refer to pages 5 (Windows) or 10 (Macintosh) for the installation procedure.

Start up the software.

For subsequent operation, refer to the owner’s manual for each software program (online help/PDF manual).

n In order to view PDF files, you will need to install Acrobat Reader in your computer (Windows page 5, Macintosh page 10).

English

Limitations on the PF-500 when using the File Utility

The accessory CD-ROM contains a File Utility program. By using this software, you can transfer files between the internal memory of the PF-500 and your computer, and edit them. There are some operating states of the PF-500 in which it is not possible to use the File Utility or in which some File Utility functions are not available.

You cannot use File Utility to perform file operations in the following states.

• Demo song mode

• Song recording/playback mode

• During ﬁle operations

• During the various [SONG SETTING] operations

The following operations cannot be performed while File Utility is running.

• File operations

• Song loading

• Track button on/off

The following operations cannot be performed on the PF-500.

• Changing the name of a protected song

(A “protected song” is song data such as a preset song that has been copied to the storage memory.)

• Changing the ﬁlename extension of a ﬁle

• Japanese display in the LCD screen

• Creating a folder

• Copying a folder from the computer to the storage memory

• Copying a ﬁle within the same folder

• Transmitting a protected song to the computer

• Transmitting path information to a device

n When transferring a file between the PF-500 and your computer, you must set the type of characters on your PF-500 ([CharacterCode]) to match

the language of the operating system for the computer in which you installed File Utility. If the character code of the PF-500 does not match the language of the computer that is running File Utility, the file may not be handled correctly.

n On the PF-500, the File Utility ID is fixed at “1”. If you specify an ID other than “1,” you will be unable to transmit or receive data. For details

on the File Utility ID, refer to the File Utility PDF manual.

Accessory CD-ROM Installation Guide (PF-500) 3

For Windows Users

Contents of the CD-ROM

The CD-ROM contains a variety of applications (with installers) and data in the following folders.

Folder Name Application Name Contents

Acroread_ Acrobat Reader

English

FileUtil_ File Utility

USBdrv_ YAMAHA USB MIDI Driver (for Win98, Me) Enables your computer to communicate with the PF-500 when your compu-

USBdrv2k_ YAMAHA USB MIDI Driver (for Win2000, XP)

Mididrv_ YAMAHA CBX Driver Allows the serial port of your computer to be connected directly to the PF-

SongData Demonstration Song Enables you to use the File Utility to transmit data to the PF-500 so you can

MIDI Setup Enables you to use the File Utility.

PDF (Portable Document Format) viewer. Enables you to view each PDF manual for the applications.

Enables you to manage ﬁles in the storage memory on the PF-500.

ter and the PF-500 are connected using a USB cable.

500 so that MIDI messages can be transferred.

enjoy demo song (SMF ﬁle) playback on the PF-500.

Adv Piano Suite Lite You can experience the essence of the Adventus Piano Suite, a music soft-

ware for learning, playing, and creating.

advdoc Getting Started with Piano Suite Lite Basic guide for setup and exploration of Piano Suite Lite.

yamahamusicsoft.com Yamaha various software Introduction for music software products from Yamaha.

*1 Unfortunately, Yamaha makes no guarantee concerning the stability of this program nor can it offer user support for it. *2 The applications are supplied with online/PDF manuals.

4 Accessory CD-ROM Installation Guide (PF-500)

Minimum System Requirements

n Depending on your operating system, it may be necessary to satisfy

conditions in addition to those listed below.

• File Utility (including MIDI setup)

Computer:

OS:

Available Memory: 16 MB or more Hard Disk: Display:

PC with 75 megahertz (MHz); Intel® Pentium®/ Celeron™ family

Windows® 95/98/98SE/Me/NT4.0/2000/XP Home Edition/XP Professional

4 MB or more 640 × 480, High Color (16 bit)

• USB MIDI Driver

Computer:

OS:

Available Memory: 32 MB or more Hard Disk:

PC (with USB port) with 166 megahertz (MHz); Intel® Pentium®/Celeron™ family

Windows® 98/98SE/Me/2000/XP Home Edition/XP Professional

2 MB or more

• YAMAHA CBX Driver

OS:

Windows® 95/98/98SE/Me/NT4.0/2000/XP Home Edition/XP Professional

Software Installation

n For details about the application software which has no installation

guide described below, refer to the online manual of each software.

●

→

Windows 98/Me users See below.

→

Windows 2000 users See page 6.

→

Windows XP users See page 7.

n Before you install the USB MIDI driver, you can minimize the

possibility of problems by putting your computer in the following state.

• Close all applications and windows that you are not using.

• Disconnect all cables from the PF-500 except for the cable whose driver you are installing.

Installing the driver on a Windows 98/Me system

Start the computer. Insert the included CD-ROM into the CD-ROM drive. Make sure the POWER switch on the PF-500 is set to OFF and

use the USB cable to connect the USB terminal of the computer (or the USB hub) to the USB terminal of the PF-500. When the PF-500 is turned on, the computer automatically displays the “Add New Hardware Wizard.” If the Add New Hardware Wizard does not appear, click “Add New Hardware” in the Control Panel.

n For Windows Me users, check the radio button to the left of “Au-

tomatic search for a better driver (Recommended)” and click [Next]. The system automatically starts searching and installing the driver. Proceed to Step 8. If the system does not detect the driver, select “Specify the location of the driver (Advanced)” and specify the CD-ROM drive’s root directory (e.g., D:\) to install the driver.

Windows 98

English

Acrobat Reader

In order to view the PDF manuals included with each application, you’ll need to install Acrobat Reader.

n If an older version of Acrobat Reader is installed on your PC, you’ll

need to uninstall it before proceeding.

Double-click on the “Acroread_” folder. Four different language folders will be displayed.

Select the language you want to use and double-click on its folder. “ar500***.exe” ﬁle will be displayed. (“***” indicates the selected language.)

Double-click on the “ar500***.exe.” Acrobat Reader Setup Dialog box will be displayed.

Execute the installation by following the on-screen directions. After installation is complete, the Acrobat folder appears on your PC (in Program Files, as the default). For information on using the Acrobat Reader, refer to the Reader Guide in the Help menu.

USB MIDI Driver

To operate the PF-500 from your computer via USB, you’ll need to install the appropriate driver software. The USB-MIDI driver is software that transfers MIDI data back and forth between sequence software and the PF-500 via a USB cable.

Computer

Windows Me

Sequence

Software

Driver

USB cable

PF-500

METRONOME

GRAND

E.PIANO

E.CLAVI-

E.PIANO

GRAND

HARPSI-

VIBRA-

VOICE

TRACK

EXTRA

TRACKS

SETTINGSTART/STOP

FILE

SONG

START

TOP

STOP

SONG SELECT

REC

SETTING

SONG KEYBOARD

UPDOWN

NEW SONG

SYNCHRO START

CAD

MAXMIN

DEMO TEMPO

SONG BALANCEMASTER VOLUME

SONG

MIDI

CONTRAST

PIANO 1

CHORD

PIANO 2

CHORD

PHONE

SETTING

GUITAR

SPLIT CHORUSREVERB

OTHER

CHURCH

WOOD

JAZZ

SYNTH.

BRILLIANCE

SETTING

ORGAN

BASS

ORGAN

PAD

VARIATION BRIGHTMELLOW

E.BASS XG

STRINGS

CHOIR

EXIT

EFFECT

VOICE

Accessory CD-ROM Installation Guide (PF-500) 5

Click [Next]. The window below enables you to select the search method.

English

Check the radio button to the left of “Search for the best driver for your device. (Recommended).” Click [Next]. The window below enables you to select a location in which to install the driver.

Windows 98

Windows Me

Check the “CD-ROM drive” box and uncheck all other items. Click [Next].

n The system may ask you to insert a Windows CD-ROM while it

checks for the driver. Specify the USBdrv_ directory of the CDROM drive (such as D:\USBdrv_\) and continue the installation.

n When using the Windows 98, specify the USBdrv_ directory of the

CD-ROM drive (such as D:\USBdrv_\) and continue the installation.

When the system detects the driver on the CD-ROM and is ready for installation, it displays the following screen. Make sure that the “YAMAHA USB MIDI Driver” is listed, and click [Next]. The system starts the installation.

8 When the installation is complete, the following screen appears.

Click [Finish].

n Some computers may take about ten seconds to show this screen

after the installation is complete.

The driver has been installed.

● Installing the driver on a Windows 2000 system

1 Start the computer and use the “Administrator” account to log into

Windows 2000.

2 Select [My Computer | Control Panel | System | Hardware | Driver

Signing | File Signature Veriﬁcation], and check the radio button to the left of “Ignore -Install all ﬁles, regardless of ﬁle signature” and click [OK].

3 Insert the included CD-ROM into the CD-ROM drive. 4 Make sure the POWER switch on the PF-500 is set to OFF and

5 Check the radio button to the left of “Search for a suitable driver

for my device. (Recommended).” Click [Next]. The window that appears enables you to select a location in which to install the driver.

6 Check the “CD-ROM drives” box and uncheck all other items.

Click [Next].

n The system may ask you to insert a Windows CD-ROM while it

checks for the driver. Specify the “USBdrv2k_” directory of the CD-ROM drive (such as D:\USBdrv2k_\) and continue the installation.

7 When the installation is complete, the system displays “Complet-

ing the Found New Hardware Wizard.” Click [Finish].

n Some computers may take about ten seconds to show this screen

after the installation is complete.

8 Restart the computer.

The driver has been installed.

6 Accessory CD-ROM Installation Guide (PF-500)

● Installing the driver on a Windows XP system

1 Start the computer. 2 Select [Start | Control Panel].

If the control panel appears as shown below, click “Switch to Classic View” in the upper left of the window. All control panels and icons will be displayed.

3 [System | Hardware | Driver Signing | File Signature Veriﬁcation],

and check the radio button to the left of “Ignore -Install all ﬁles, regardless of ﬁle signature” and click [OK].

4 Click the [OK] button to close System Properties, and then click

“X” in the upper right of the window to close the Control Panel.

5 Insert the included CD-ROM into the CD-ROM drive. 6 Make sure the POWER switch on the PF-500 is set to OFF and

7 Check the radio button to the left of “Search for a suitable driver

for my device. (Recommended).” Click [Next]. The system starts the installation.

8 When the installation is complete, the system displays “Complet-

ing the Found New Hardware Wizard.” Click [Finish].

n Some computers may take about ten seconds to show this screen

after the installation is complete.

9 Restart the computer.

The driver has been installed.

Serial Driver

1 Double-click on the “Mididrv_” folder.

“Setup.exe” ﬁle will be displayed.

2 Double-click on the “Setup.exe” ﬁle.

When the setup has been initialized, the “Welcome” window will appear.

English

3 Click [Next].

The “Select operation” window will appear.

4 Click the radio button to the left of “Install YAMAHA CBX

Driver.” Click [Next].

5 The license agreement for the YAMAHA CBX Driver will be dis-

played. Please read it carefully.

6 Click [Yes].

The “Select COM port” window will appear.

Accessory CD-ROM Installation Guide (PF-500) 7

7 Click the radio button to the left of the COM port to use.

Normally you will use COM1. Click [Next]. “Select the number of MIDI output ports” will appear.

MIDI port setting (MIDI SETUP)

Before setting the MIDI port on the File Utility, you should set the MIDI port from the MIDI SETUP toolbar.

1 Start the File Utility. 2 Click the MIDI Setup button in the Toolbar called up via step #1.

MIDI Setup button

English

8 Click the radio button to the left of the “Use multiple MIDI output

ports” and click [Next]. The MIDI driver will be installed, and the “MIDI Mapper Question” window will appear.

9 Click [Yes].

The system displays the following message “Set the HOST SELECT switch on a tone module to PC-2.”

0 Click [OK].

A message will inform you that setup has been completed.

A In order for the newly installed YAMAHA CBX Driver to take

effect, make sure that “Yes, I want to restart my computer now” is installed, and click [OK]. The computer will restart.

3 In the MIDI Setup window called up via step#2, click the [▼] but-

ton at the right end of each box and make the port settings as shown.

n In order for MIDI ports to be available here, you’ll need to select

the relevant MIDI port within the application software —File Utility. This is the port that you’ll use in the various software. For details on setting the MIDI port, refer to the PDF manual of File Utility.

The driver has been installed.

File Utility, MIDI Setup

Once you‘ve installed these software programs, you can use your computer to access and organize data stored to media connected to the PF-500 (Storage memory).

1 Double-click on the “FileUtil_” folder in the CD-ROM.

“Setup.exe” ﬁle will be displayed.

2 Double-click on the “Setup.exe” ﬁle.

The File Utility setup dialog will be displayed.

3 Execute the installation by following the on-screen directions.

For details, refer to the on-line Help or the PDF owner’s manual.

8 Accessory CD-ROM Installation Guide (PF-500)

For Macintosh Users

Contents of the CD-ROM

The CD-ROM contains a variety of applications (with installers) and data are contained in the following folders.

Folder Name Application Name Contents

Acroread_ Acrobat Reader 4.0 *1

OMS_ Open Music System (OMS) 2.3.8

OMS Setup for YAMAHA Contains the OMS Setup ﬁles for the Yamaha PF-500.

USBdrv_ YAMAHA USB MIDI Driver Enables your computer to communicate with the PF-500 when your compu-

FileUtil_ File Utility

SongData Demonstration Song Enables you to use the File Utility to transmit data to the PF-500 so you can

yamahamusicsoft.com Yamaha various software Introduction for music software products from Yamaha.

*1 Unfortunately, Yamaha makes no guarantee concerning the stability of this program nor can it offer user support for it. *2 The applications are supplied with online/PDF manuals.

PDF (Portable Document Format) viewer. Enables you to view each PDF manual for the applications.

Enables you to use several MIDI applications on the Mac OS.

ter and the PF-500 are connected using a USB cable.

Enables you to manage ﬁles in the storage memory on the PF-500.

enjoy demo song (SMF ﬁle) playback on the PF-500.

English

• OMS® and are trademarks of Opcode Systems, Inc.

Accessory CD-ROM Installation Guide (PF-500) 9

Minimum System Requirements

Open Music System (OMS) 2.3.8

• File Utility

Computer: A Macintosh computer with a PowerPC or later CPU OS: Mac OS 8.0 through 9.2.2 (Mac OS X is not sup-

Available Memory: 6 MB or more Hard Disk: 4 MB or more (except for OMS) Display: 640 × 480, 256 colors or more Other: OMS 2.3.3 or later (included in the CD-ROM in the

• USB MIDI Driver

English

Computer: A Macintosh computer with a USB connector and a

OS: Mac OS 8.6 through 9.2.2 (Mac OS X is not sup-

Available Memory: 64 MB or more (128 MB or more is recommended)

n Turn off virtual memory.

Hard Disk: 2 MB or more Other: OMS 2.3.3 or later (included in the CD-ROM in the

Software Installation

n For details about the application software which has no installation

ported.)

package)

PowerPC or later CPU

ported.)

package)

guide described below, refer to the owner’s manual of each software.

OMS allows you to use several MIDI applications on the Mac OS at the same time.

1 Double-click on the “OMS_” folder (English version only).

“Install OMS 2.3.8” will be displayed.

2 Double-click on “Install OMS 2.3.8.”

OMS Setup Dialog will be displayed.

3 Execute the installation by following the on-screen directions.

After the installation, select “Restart.”

n After the installation is complete, you may possibly encounter an

error message warning that the installer did not close. In this case, go to the “File” menu and select “Quit” to close the installer. Then reboot the computer.

After restarting the Macintosh, you will ﬁnd the “Opcode”/“OMS Applications” folder on your computer (Hard Disk, as the default).

4 Copy the “OMS_2.3_Mac.pdf” in the CD-ROM to the “OMS

Applications” folder (drag-and-drop it to the folder). Refer to the “OMS_2.3_Mac.pdf” (English version only) how to use the application.

5 Copy the “OMS Setup for YAMAHA” in the CD-ROM to the

“OMS Applications” folder (drag-and-drop it to the folder). In the “OMS Setup for YAMAHA” folder you will ﬁnd the OMS Setup ﬁles for the Yamaha tone generators, which can be used as templates.

Acrobat Reader 4.0

In order to view the PDF manuals included with each application, you’ll need to install Acrobat Reader.

1 Double-click on the “Acroread_” folder.

Four different language folders will be displayed: English, German, French and Spanish.

2 Select the language you want to use and double-click on its folder.

“Reader Installer” will be displayed. The Installer name may differ depending on the language you select.

3 Double-click on the “Reader Installer.”

Acrobat Reader Setup Dialog will be displayed.

4 Execute the installation by following the directions appearing on

the screen. After installation is complete, the Acrobat folder appears on your computer (in Hard Disk, as the default). For information on using the Acrobat Reader, refer to the Reader Guide in the Help menu.

USB MIDI Driver

Computer

Sequence

Software

USB cable

OMS

Driver

First install OMS before you install the USB-MIDI driver. Also, after installing the driver, you will need to set up OMS (above).

1 Start the computer. 2 Insert the included CD-ROM into the CD-ROM drive. The system

displays the CD-ROM icon on the desktop.

3 Double-click the CD-ROM icon and double-click the “Install

USB Driver” icon in the “USBdrv_” folder to display the following installation screen.

PF-500

METRONOME

GRAND

E.PIANO

GRAND

HARPSI-

VIBRA-

VOICE

MIDI

CAD

E.CLAVI-

CONTRAST

PIANO 1

PIANO 2

CHORD

PHONE

SETTING

CHORD

GUITAR

SPLIT CHORUSREVERB

OTHER

CHURCH

JAZZ

SYNTH.

WOOD

BRILLIANCE

SETTING

ORGAN

PAD

BASS

VARIATION BRIGHTMELLOW

STRINGS

CHOIR

E.BASS XG

EXIT

EFFECT

VOICE

TRACK

EXTRA

TRACKS

FILE

SETTINGSTART/STOP

SONG

START

TOP

STOP

SONG SELECT

REC

SETTING

SONG KEYBOARD

UPDOWN

SYNCHRO START

NEW SONG

MAXMIN

DEMO TEMPO

SONG BALANCEMASTER VOLUME

SONG

10 Accessory CD-ROM Installation Guide (PF-500)

4 The “Install Location” box displays the destination of the installa-

tion. If you wish to change the destination disk or folder, use the [Switch Disk] button and the pop-up menu to specify the desired destination.

n This box usually displays the start-up disk as the destination.

5 Click the [Install] button. The system displays the following mes-

sage: “This installation requires your computer to restart after installing this software. Click Continue to automatically quit all other running applications.” Click [Continue].

n To cancel the installation, click [Cancel].

6 The installation starts. If the driver has already been installed, you

will receive the following message. To return to step 3, press [Continue]. To complete the installation, click [Quit].

File Utility, MIDI Setup

Once you‘ve installed these software programs, you can use your computer to access and organize data stored to media connected to the PF-500 (Storage memory).

1 Double-click on the “FileUtil_” folder in the CD-ROM.

“Install File Utility” ﬁle will be displayed.

2 Double-click on the “Install File Utility” ﬁle.

The File Utility installation dialog will be displayed. Execute the installation by following the on-screen directions.

3 After installing, restart the computer.

For details, refer to the on-line Help or the PDF owner’s manual.

English

7 When the installation is complete, the system displays the follow-

ing message: “Installation was successful. You have installed software which requires you to restart your computer.” Click [Restart]. The computer automatically restarts. You can locate the installed ﬁles in the following locations:

• System Folder | Control Panels | YAMAHA USB MIDI Patch

• System Folder | Extensions | USB YAMAHA MIDI Driver

• System Folder | OMS Folder | YAMAHA USB MIDI OMS Driver

Accessory CD-ROM Installation Guide (PF-500) 11

Setting up OMS (For USB connection)

The OMS studio setup file for the PF-500 is contained in the included CD-ROM. This studio setup file is used for setting up OMS.

n Before performing the following procedure, the OMS and USB MIDI

1 Use a USB cable to connect the USB terminal of the computer (or

the USB hub) to the USB terminal of the PF-500 and turn the PF500’s power on.

2 Start the computer.

English

3 Insert the included CD-ROM into the CD-ROM drive of your

Macintosh computer. The CD-ROM icon appears on the desktop.

4 Double-click on the CD-ROM icon, “OMS_”, and “OMS Setup

for YAMAHA.” The ﬁle “PF-500-USB” appear. Copy these to the hard disk on your computer.

n If you want to use a serial connection instead of using USB, please

n When using the serial connection for the File Utility, set the MIDI

5 Double-click on the “PF-500-USB” ﬁle to start the OMS Setup. 6 After starting the OMS Setup, the Studio setup ﬁle double-clicked

in step #5 opens.

Driver should be installed.

copy and use the following files.

• “PF-500-Printer” Use this for serial connection via the printer port.

• “PF-500-Modem” Use this for serial connection via the modem port.

Out:/ MIDI In: setting in the OMS Port Setup to MIDI Time PiecePrinter, or MIDI Time Piece-Modem.

Indicates this setup is available

Depending on the Macintosh and operating system version that you are using, the included studio setup file for the PF-500 still may not work even after you have performed the above steps. (MIDI transmission and reception will not be possible even if the setup is valid.) In this case, use the following procedure to re-create the setup file.

1 Connect the PF-500 and Macintosh via USB or serial cable,

and turn on the power of the PF-500.

2 Start up OMS Setup, and from the “File” menu, choose “New

setup.”

3 The OMS driver search dialog box will appear. Check

[Modem] or [Printer] if you are using a serial connection. Uncheck both of these if you are using a USB connection.

4 Click the [Find] button to search for the device.

When the search has succeeded, the OMS Driver Setting dialog box will display the following.

For a USB connection: USB-MIDI 1 For a serial connection: MIDI Time Piece-Modem (Printe_)

• If the device was found correctly, click the [OK] button to proceed.

• If the device was not found, re-check that the cable connections are correct, and repeat the procedure from step 1.

5 Make sure that the port is shown below the device that was

found. (In the case of the PF-500, this will be a name such as USB-MIDI, Modem, or Printer.) Check the check box for the port, and then click the [OK] button.

6 A dialog box will appear, allowing you to name the ﬁle that

will be saved. Input the desired ﬁlename, and click [Save]. This completes OMS setup.

7 From the “Studio” menu, choose “Test,” and click the port

icon. If a channel sounds on the PF-500, the system is operating correctly.

n If “ ” is not indicated at the right of the setup file name, select

“Make Current” from the “File” menu and execute the save operation.

The OMS studio setup has been completed.

n After the OMS studio setup above has been completed, your com-

puter will recognize only the PF-500 as a MIDI instrument. If you use another MIDI instrument in addition to the PF-500 or you add a second PF-500 to the existing system, you should create an original Studio Setup file. For details, refer to the on-line manual supplied with the OMS.

For details on using OMS, refer to OMS_2.3_Mac.pdf, included with OMS.

12 Accessory CD-ROM Installation Guide (PF-500)

Troubleshooting

The driver cannot be installed.

• Is the USB cable connected correctly?

→ Check the USB cable connection. → Disconnect the USB cable, then connect it again.

• [Windows] Is the USB function enabled on your computer? → When you connect the PF-500 to the computer for the ﬁrst

time, if the “Add New Hardware Wizard” does not appear, the USB function on the computer may be disabled. Perform the following steps.

1 Double-click “System” in the Control Panel to open the System

Properties window.

2 Double-click the “Device Manager” tab and make sure that no “!”

or “x” marks appear at “Universal serial bus controller” or “USB Root Hub.” If you see an “!” or “x” mark, the USB controller is disabled. For more information, refer to the owner’s manual of your computer.

• [Windows] Is any unknown device registered? → If driver installation fails, the PF-500 will be marked as an

“Unknown device,” and you will not be able to install the driver. Delete the “Unknown device” by following the steps below.

1 Double-click “System” in the Control Panel to open the System

Properties window.

2 Double-click the “Device Manager” tab. With the “View devices

by type” check box checked, look for “Other devices.”

3 If you ﬁnd “Other devices,” double-click it to extend the tree to

look for “Unknown device.” If one appears, select it and click the [Remove] button.

4 Remove the USB cable from the PF-500, and make the connection

again.

5 Install the driver again.

When controlling the PF-500 from your computer via USB, the PF-500 does not operate correctly or no sound is heard.

• Did you install the driver?

• If you are using a Macintosh, did you install OMS before installing

the USB MIDI driver?

• Is the USB cable connected correctly?

• Are the volume settings of the tone generator, playback device,

and application program set to the appropriate levels?

• Have you selected an appropriate port in the application software?

• Are you using the latest USB MIDI driver?

The latest driver can be downloaded from the www.yamahasynth.com Web site.

• Is the HOST SELECT switch set correctly?

Cannot suspend or resume the computer correctly.

• Do not suspend the computer while the MIDI application is running.

• If you are using Windows 2000, you may not be able to suspend/ resume normally, depending on the particular environment (USB Host Controller, etc.). Even so, simply disconnecting and connecting the USB cable will allow you to use the PF-500 functions again.

How can I delete or re-install the driver?

[Windows Me/98]

1 When the PF-500 is recognized correctly, double-click “System”

in the Control Panel to open the System window.

2 Double-click the “Device Manager” tab, select “YAMAHA USB

MIDI Driver” and delete it.

3 Use the MS-DOS prompt or Explorer to delete the following three

ﬁles.

n To delete these files using Explorer, select “Fol Options” from

the Tool (View) menu, and select “Show all files (and folders).”

• \WINDOWS\INF\OTHER\YAMAHAPF-500.INF

• \WINDOWS\SYSTEM\Xgusb.drv

•

\WIN

DOWS\SYSTEM\Ymidusb.sys

4 Disconnect the USB cable. 5 Restart the computer. 6 Re-install the driver.

[Macintosh]

1 Delete the ﬁles in the following locations:

• System Folder | Control Panels | YAMAHA USB MIDI Patch

• System Folder | Extensions | USB YAMAHA MIDI Driver

• System Folder | OMS Folder | YAMAHA USB MIDI OMS Driver

2 Restart the computer. 3 Install the driver and set up OMS.

English

Playback response is delayed.

• Does your computer satisfy the system requirements?

• Is any other application or device driver running?

[Macintosh]

→ Turn off virtual memory. → Disable AppleTalk.

Accessory CD-ROM Installation Guide (PF-500) 13

Wichtige Hinweise zur CD-ROM

Datentypen

Diese CD-ROM enthält Anwendungssoftware. Weitere Informationen zur Software und zu ihrer Installation finden Sie auf Seite 4 (Windows) und 9 (Macintosh).

Diese Anwendungen ermöglichen es Ihnen, zwischen einem Computer und dem PF-500 Daten zu übertragen.

Betriebssystem

Die Anwendungen auf dieser CD-ROM werden in einer Version für Windows und in einer Version für das Macintosh-Betriebssystem bereitgestellt. Der Installationsvorgang und die Anwendungen für die beiden Betriebssysteme sind nicht identisch. Befolgen Sie daher die Ihrem Betriebssystem entsprechende Installationsanleitung.

Deutsch

→ Windows Siehe Seite 3, 5, 13. → Macintosh Siehe Seite 3, 10, 13.

Medienformate

Das PF-500 und die Software „File Utility“ sind kompatibel mit den Medien im MS-DOS-Format.

Versuchen Sie bitte niemals, diese CD-ROM auf einem Audio-CD-Player abzuspielen, da dies sowohl zu Hörschäden als auch zu Beschädigungen an CD-Player oder Boxen führen kann.

2 Accessory CD-ROM Installationshandbuch (PF-500)

Verfahren zur Installation der CD-ROM

Die folgenden Schritte sind für Windows und Macintosh identisch.

Stellen Sie sicher, daß das System die Betriebsanforderungen der Software (File Utility, Treiber usw.) erfüllt (Windows Seite 5, Macintosh Seite 10).

Schließen Sie das PF-500 an den Computer an. Informationen zu den Anschlüssen ﬁnden Sie in der Bedienungsanleitung.

HINWEIS

Je nach dem, welches Computersystem Sie verwenden, sind einige Anschlußarten u. U. nicht möglich.

Installieren Sie auf dem Computer den der Anschlußart entsprechenden Treiber, und nehmen Sie die erforderlichen Einstellungen vor. Die Pfeile in der folgenden Liste symbolisieren die Kabelverbindungen.

• Anschluß über ein USB-Kabel

↔

USB-Schnittstelle des PF-500

• Anschluß über ein serielles Kabel [TO HOST]-Buchse des PF-500

• Anschluß über MIDI-Kabel MIDI-Schnittstelle des PF-500

Installieren Sie die Software (File Utility usw.) Informationen zum Installationsverfahren ﬁnden Sie auf Seite 5 (Windows) bzw. 10 (Macintosh).

Starten Sie die Software.

Informationen zur Verwendung finden Sie in der Bedienungsanleitung des jeweiligen Softwareprogramms (Onlinehilfe/Handbuch als PDF-Datei).

HINWEIS

Um PDF-Dateien anzeigen zu können, muß Acrobat Reader auf Ihrem Computer installiert sein (Windows Seite 5, Macintosh Seite 10).

USB-Schnittstelle des Computers … Windows Seite 5, Macintosh Seite 10

↔

Serielle Schnittstelle des Computers (RS-232C- oder RS-422-Schnittstelle) … Seite 7

←

MIDI-Interface (externes Gerät) → Computer … Windows Seite 5, Macintosh Seite 10

Einschränkungen für das PF-500 bei Verwendung von „File Utility“

Die mitgelieferte CD-ROM enthält das Programm „File Utility“. Durch Verwendung dieser Software können Sie Dateien zwischen dem internen Speicher des PF-500 und Ihrem Computer austauschen und bearbeiten. In einigen Betriebszuständen des PF-500 ist die Verwendung von „File Utility“ nicht möglich bzw. einige Funktionen von „File Utility“ sind nicht verfügbar.

In den folgenden Betriebszuständen können Sie „File Utility“ nicht zur Ausführung von Dateivorgängen verwenden.

• Im Demo-Song-Modus

• Im Aufnahme- bzw. Wiedergabe-Modus

• Während der Ausführung von Dateivorgängen

• Während der verschiedenen [SONG SETTING]-Operationen

Die folgenden Vorgänge sind während der Ausführung von „File Utility“ nicht möglich.

• Dateivorgänge

• Laden von Songs

• Ein-/Ausschalten der Spurtasten

Die folgenden Vorgänge können auf dem PF-500 nicht ausgeführt werden.

• Ändern des Namens eines geschützten Songs

(Ein „geschützter Song“ ist z.B. ein Preset-Song, der sich im internen Speicher beﬁndet.)

• Ändern der Dateinamenserweiterung einer Datei

• Anzeigen des japanischen Displays

• Anlegen eines Ordners

• Kopieren eines Ordners vom Computer in den Speicher

• Kopieren einer Datei innerhalb eines Ordners

• Übertragen eines geschützten Songs auf den Computer

• Übertragen von Pfadinformationen an ein Gerät

HINWEIS

Zum Übertragen einer Datei zwischen PF-500 und Computer müssen Sie den Zeichentyp auf dem PF-500 ([CharacterCode], Zeichencode) so einstellen, daß er der Sprache des Betriebssystems auf dem Computer entspricht, auf dem „File Utility“ installiert ist. Falls der Zeichencode des PF-500 nicht der Sprache des Computers entspricht, auf dem „File Utility“ ausgeführt wird, wird die Datei u.U. nicht richtig verarbeitet.

HINWEIS

Auf dem PF-500 ist die „File Utility ID“ auf „1“ festgelegt. Falls Sie eine andere ID als „1“ angeben, können Sie keine Daten senden oder empfangen. Einzelheiten zur „File Utility ID“ finden Sie im als PDF-Datei vorliegenden Handbuch zu „File Utility“.

Deutsch

Accessory CD-ROM Installationshandbuch (PF-500) 3

Für Windows-Benutzer

Inhalt der CD-ROM

Die CD-ROM enthält eine Reihe von Anwendungen (mit Installationsprogrammen), die Daten befinden sich in den folgenden Ordnern.

Ordnername Name der Anwendung Inhalt

Acroread_ Acrobat Reader *1

FileUtil_ File Utility

MIDI Setup Ermöglicht die Verwendung von „File Utility“.

USBdrv_ YAMAHA USB MIDI Driver (für Win98, Me) Ermöglicht die Kommunikation zwischen Computer und PF-500, wenn die

USBdrv2k_ YAMAHA USB MIDI Driver (für Win2000, XP)

Anzeigeprogramm für PDF-Dateien (Portable Document Format), mit dem Sie die im PDF-Format vorliegenden Softwarehandbücher anzeigen können.

Hiermit können Sie die Dateien im internen Speicher des PF-500 organisieren.

Verbindung über ein USB-Kabel hergestellt wird.

Deutsch

Mididrv_ YAMAHA CBX Driver Ermöglicht den direkten Anschluß der seriellen Schnittstelle des Computers

SongData Demonstration Song Ermöglicht die Verwendung von „File Utility“ zur Übertragung von Daten

Adv Piano Suite Lite Sie können die Kernfunktionen der „Adventus Piano Suite“ ausprobieren,

advdoc Getting Started with Piano Suite Lite (Erste

yamahamusicsoft.com Verschiedene Yamaha-Programme Vorstellung von Musiksoftware-Produkten von Yamaha.

*1 Yamaha kann keine Garantie für die Stabilität dieses Programms abgeben und auch keine technische Unterstützung dafür anbieten. *2 Für diese Anwendungen liegt eine Onlinehilfe/ein Handbuch als PDF-Datei vor.

an das PF-500, so daß MIDI-Befehle übertragen werden können.

an das PF-500, so daß Sie auf dem PF-500 Demo-Songs (SMF-Dateien) abspielen können.

einer Musiksoftware, mit deren Hilfe Sie das Klavierspielen und das Erstellen eigener Kompositionen lernen können.

Basisanleitung zum Einrichten und Kennenlernen von Piano Suite Lite.

Schritte in Piano Suite Lite)

4 Accessory CD-ROM Installationshandbuch (PF-500)

Mindest-Systemanforderungen

HINWEIS

Je nach Betriebssystem müssen außer den nachstehend aufgelisteten Bedingungen u.U. noch weitere erfüllt sein.

• File Utility (einschließlich MIDI Setup)

Computer: PC mit 75 Megahertz (MHz); Prozessorfamilie

Betriebssystem: Windows® 95/98/98SE/Me/NT4.0/2000/XP Home

Verfügbarer Arbeitsspeicher: 16 MB oder mehr

Festplatte: 4 MB oder mehr Anzeige: 640 × 480, High Color (16 Bit)

Intel® Pentium®/Celeron™

Edition/XP Professional Edition

• USB MIDI Driver

Computer: PC mit USB und 166 Megahertz (MHz);

Betriebssystem: Windows® 98/98SE/Me/2000/XP Home Edition/XP

Verfügbarer Arbeitsspeicher: 32 MB oder mehr

Festplatte: 2 MB oder mehr

Prozessorfamilie Intel® Pentium®/Celeron™

Professional Edition

• YAMAHA CBX Driver

Betriebssystem: Windows® 95/98/98SE/Me/NT4.0/2000/XP Home

Edition/XP Professional Edition

Softwareinstallation

HINWEIS

Einzelheiten zur Anwendungssoftware, für die Sie im folgenden keine Installationsanleitung finden, entnehmen Sie bitte dem Onlinehandbuch der jeweiligen Software.

Acrobat Reader

Um die im PDF-Format vorliegenden Handbücher der einzelnen Anwendungen anzeigen zu können, müssen Sie Acrobat Reader installieren.

HINWEIS

Wenn bereits eine ältere Version von Acrobat Reader auf Ihrem PC installiert ist, müssen Sie diese deinstallieren, bevor Sie mit der Installation fortfahren.

1 Doppelklicken Sie auf den Ordner „Acroread_“.

Daraufhin werden Ordner für vier verschiedene Sprachen angezeigt.

2 Wählen Sie die zu verwendende Sprache aus, und doppelklicken

Sie auf den entsprechenden Ordner. Die Datei „ar500***.exe“ wird angezeigt. (Die Zeichenfolge anstelle von „***“ gibt die ausgewählte Sprache an.)

3 Doppelklicken Sie auf „ar500***.exe“.

Das Dialogfeld „Acrobat Reader Setup“ wird angezeigt.

4 Führen Sie die Installation aus, indem Sie den Anweisungen auf

dem Bildschirm folgen. Nach erfolgreicher Installation beﬁndet sich das AcrobatVerzeichnis auf Ihrem PC (standardmäßig unter „Programme“). Informationen über die Verwendung von Acrobat Reader ﬁnden Sie im Menü „Hilfe“ unter „Reader Guide“.

→ Windows 98/Me-Benutzer Siehe unten. → Windows 2000-Benutzer Siehe Seite 6. → Windows XP-Benutzer Siehe Seite 7.

HINWEIS

Bevor Sie den USB MIDI Driver installieren, sollten Sie das Problemrisiko minimieren, indem Sie den Computer in den folgenden Zustand versetzen.

• Schließen Sie sämtliche Anwendungen und Fenster, die Sie momentan nicht verwenden.

• Entfernen Sie vom PF-500 alle Kabel mit Ausnahme desjenigen Kabels, dessen Treiber Sie gerade installieren.

●

Installation des Treibers unter Windows 98/Me

1 Starten Sie den Computer. 2 Legen Sie die mitgelieferte CD-ROM in das CD-ROM-Laufwerk

ein.

3 Vergewissern Sie sich, daß der Schalter [POWER] am PF-500 auf

OFF (Aus) gestellt ist, und verwenden Sie das USB-Kabel, um die USB-Schnittstelle des Computers (oder den USB-Hub) mit der USB-Schnittstelle des PF-500 zu verbinden. Sobald das PF-500 eingeschaltet wird, wird auf dem Computerbildschirm der „Hardware-Assistent“ angezeigt. Falls der „Hardware-Assistent“ nicht angezeigt wird, klicken Sie in der Systemsteuerung auf „Hardware“.

HINWEIS

Für Windows Me-Benutzer: Wählen Sie die Option „Automatisch nach demo besten Treiber suchen (Empfohlen)“ aus, und klicken Sie auf [Weiter]. Die Suche nach dem Treiber und die Installation des Treibers werden automatisch gestartet. Fahren Sie mit Schritt 8 fort. Falls das System den Treiber nicht erkennt, wählen Sie zum Installieren des Treibers die Option „Position des Treibers angeben (Erweitert)“ aus, und geben Sie das Stammverzeichnis des CD-ROM-Laufwerks an (z.B. „D:\“).

Windows 98

Windows Me

Deutsch

USB MIDI Driver

Um das PF-500 über USB von einem Computer aus bedienen zu können, müssen Sie zunächst die geeignete Treibersoftware (englisch: Driver) installieren. Der USB MIDI Driver ist eine Software, die über ein USB-Kabel MIDI-Daten zwischen der Sequencer-Software und dem PF-500 überträgt.

Computer

Sequenzer-

programm

Treiber

USB-Kabel

PF-500

METRONOME

GRAND

E.PIANO

E.CLAVI-

E.PIANO

GRAND

HARPSI-

VIBRA-

VOICE

TRACK

EXTRA

TRACKS

SETTINGSTART/STOP

FILE

SONG

START

TOP

STOP

SONG SELECT

REC

SETTING

SONG KEYBOARD

UPDOWN

NEW SONG

SYNCHRO START

CAD

MAXMIN

DEMO TEMPO

SONG BALANCEMASTER VOLUME

SONG

MIDI

CONTRAST

PIANO 1

CHORD

PIANO 2

CHORD

PHONE

SETTING

GUITAR

SPLIT CHORUSREVERB

OTHER

CHURCH

WOOD

JAZZ

SYNTH.

BRILLIANCE

SETTING

ORGAN

BASS

ORGAN

PAD

VARIATION BRIGHTMELLOW

STRINGS

E.BASS XG

CHOIR

EXIT

EFFECT

VOICE

Accessory CD-ROM Installationshandbuch (PF-500) 5

+ 39 hidden pages