Yamaha FJR13AVC User Manual
OWNER’S MANUAL
FJR13AV(C)
LIT-11626-19-83
3P6-28199-10
EAU10041
INTRODUCTION
EAU10080
Congratulations on your purchase of the Yamaha FJR13AV(C). This model is the result of Yamaha’s vast experience in the
production of fine sporting, touring, and pacesetting racing machines. It represents the high degree of craftsmanship and
reliability that have made Yamaha a leader in these fields.
This manual will give you an understanding of the operation, inspection, and basic maintenance of this motorcycle. If you
have any questions concerning the operation or maintenance of your motorcycle, please consult a Yamaha dealer.
The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at
the date of manufacture. Yamaha has met these standards without reducing the performance or economy of operation of the
motorcycle. To maintain these high standards, it is important that you and your Yamaha dealer pay close attention to the
recommended maintenance schedules and operating instructions contained within this manual.
IMPORTANT MANUAL INFORMATION
Particularly important information is distinguished in this manual by the following notations:
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!
EAU10131
WARNING
Failure to follow WARNING instructions could result in severe injury or death
motorcycle operator, a bystander or a person inspecting or repairing the motor-
to the
cycle.
CAUTION:
NOTE:
A CAUTION indicates special precautions that must be taken to avoid damage to
the motorcycle.
A NOTE provides key information to make procedures easier or clearer.
NOTE:
● This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle
is subsequently sold.
● Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most
current product information available at the time of printing, there may be minor discrepancies between your motorcycle
and this manual. If you have any questions concerning this manual, please consult your Yamaha dealer.
EWA10010
WARNING
PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING TIPS” BOOKLET CAREFULLY
AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTORCYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES
IMPORTANT MANUAL INFORMATION
AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES. REGULAR INSPECTIONS
AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY
THE CAPABILITIES AND THE RELIABILITY OF THIS MOTORCYCLE.
*Product and specifications are subject to change without notice.
IMPORTANT MANUAL INFORMATION
AFFIX DEALER
LABEL HERE
FJR13AV(C)
OWNER’S MANUAL
©2005 by Yamaha Motor Corporation, U.S.A.
1st edition, December 2005
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in Japan.
P/N LIT-11626-19-83
EAU10192
TABLE OF CONTENTS
SAFETY INFORMATION ..................1-1
Location of important labels ...........1-5
DESCRIPTION ..................................2-1
Left view ..........................................2-1
Right view........................................2-2
Controls and instruments ................2-3
INSTRUMENT AND CONTROL
FUNCTIONS.......................................3-1
Main switch/steering lock ................3-1
Indicator and warning lights ............3-2
Speedometer ..................................3-3
Tachometer ....................................3-3
Multi-function display ......................3-4
Handlebar switches ........................3-8
Clutch lever ..................................3-10
Shift pedal ....................................3-11
Brake lever ...................................3-11
Brake pedal ..................................3-11
ABS ..............................................3-12
Fuel tank cap ................................3-12
Fuel ..............................................3-13
Catalytic converter ........................3-14
Seats ............................................3-14
Adjusting the rider seat height ......3-16
Storage compartments .................3-18
Accessory box ..............................3-18
Adjusting the headlight beams .....3-19
Handlebar position .......................3-19
Opening and closing the
cowlings .................................... 3-20
Rear view mirrors ......................... 3-21
Adjusting the front fork ................. 3-21
Adjusting the shock absorber
assembly .................................. 3-23
Sidestand ..................................... 3-24
Ignition circuit cut-off system ....... 3-25
Auxiliary DC jack .......................... 3-27
PRE-OPERATION CHECKS ............. 4-1
Pre-operation check list ................. 4-2
OPERATION AND IMPORTANT
RIDING POINTS ................................ 5-1
Starting the engine ......................... 5-1
Shifting ........................................... 5-2
Engine break-in .............................. 5-3
Parking ........................................... 5-4
PERIODIC MAINTENANCE AND
MINOR REPAIR................................. 6-1
PERIODIC MAINTENANCE .......... 6-1
Owner’s tool kit .............................. 6-1
Periodic maintenance chart for the
emission control system ............. 6-3
General maintenance and
lubrication chart .......................... 6-4
Removing and installing panels ..... 6-8
Checking the spark plugs ............ 6-11
Canister (for California only) ........ 6-12
Engine oil and oil filter cartridge ... 6-13
Final gear oil ................................. 6-15
Coolant .........................................6-17
Cleaning the air filter element ......6-18
Checking the throttle cable free
play ...........................................6-20
Valve clearance ............................ 6-20
Tires .............................................6-20
Cast wheels ..................................6-23
Accessories and replacement
parts ..........................................6-23
Clutch lever ..................................6-24
Adjusting the rear brake light
switch ........................................6-24
Checking the front and rear brake
pads ..........................................6-25
Checking the brake and clutch
fluid levels .................................6-25
Changing the brake and clutch
fluids .........................................6-27
Checking and lubricating the
cables .......................................6-27
Checking and lubricating the
throttle grip and cable ...............6-27
Checking and lubricating the
brake and shift pedals ............... 6-28
Checking and lubricating the
brake and clutch levers .............6-28
Checking and lubricating the
centerstand and sidestand ........ 6-29
Lubricating the swingarm pivots ... 6-29
TABLE OF CONTENTS
Lubricating the rear suspension ...6-30
Checking the front fork .................6-30
Checking the steering ...................6-31
Checking the wheel bearings .......6-31
Battery ..........................................6-32
Replacing the fuses ......................6-33
Replacing a headlight bulb ...........6-34
Front turn signal light ....................6-36
Replacing a rear turn signal light
bulb or a tail/brake light bulb .....6-36
Replacing the license plate light
bulb ...........................................6-37
Troubleshooting ............................6-37
Troubleshooting charts .................6-38
MOTORCYCLE CARE AND
STORAGE ..........................................7-1
Care ................................................7-1
Storage ...........................................7-3
SPECIFICATIONS .............................8-1
CONSUMER INFORMATION.............9-1
Identification numbers ....................9-1
Reporting safety defects .................9-3
Motorcycle noise regulation ............9-4
Maintenance record ........................9-5
YAMAHA MOTOR
CORPORATION, U.S.A.
STREET AND ENDURO
MOTORCYCLE LIMITED
WARRANTY ...............................9-7
YAMAHA EXTENDED SERVICE
(Y.E.S.) .......................................9-9
SAFETY INFORMATION
EAU10281
MOTORCYCLES ARE SINGLE
TRACK VEHICLES. THEIR SAFE USE
AND OPERATION ARE DEPENDENT
UPON THE USE OF PROPER RIDING
TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERATOR. EVERY OPERATOR SHOULD KNOW
THE FOLLOWING REQUIREMENTS
BEFORE RIDING THIS MOTORCYCLE.
HE OR SHE SHOULD:
● OBTAIN THOROUGH INSTRUC-
TIONS FROM A COMPETENT
SOURCE ON ALL ASPECTS OF
MOTORCYCLE OPERATION.
● OBSERVE THE WARNINGS AND
MAINTENANCE REQUIREMENTS IN THE OWNER’S MANUAL.
● OBTAIN QUALIFIED TRAINING
IN SAFE AND PROPER RIDING
TECHNIQUES.
● OBTAIN PROFESSIONAL TECH-
NICAL SERVICE AS INDICATED
BY THE OWNER’S MANUAL
AND/OR WHEN MADE NECESSARY BY MECHANICAL CONDITIONS.
Safe riding
● Always make pre-operation
checks. Careful checks may help
prevent an accident.
● This motorcycle is designed to car-
ry the operator and a passenger.
● The failure of motorists to detect
and recognize motorcycles in traffic is the predominating cause of
automobile/motorcycle accidents.
Many accidents have been caused
by an automobile driver who did
not see the motorcycle. Making
yourself conspicuous appears to
be very effective in reducing the
chance of this type of accident.
Therefore:
• Wear a brightly colored jacket.
• Use extra caution when you are
approaching and passing
through intersections, since intersections are the most likely
places for motorcycle accidents
to occur.
• Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.
● Many accidents involve inexperi-
enced operators. In fact, many operators who have been involved in
accidents do not even have a current motorcycle license.
• Make sure that you are qualified
and that you only lend your
motorcycle to other qualified operators.
• Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
• We recommend that you practice riding your motorcycle
where there is no traffic until you
have become thoroughly familiar with the motorcycle and all of
its controls.
● Many accidents have been caused
by error of the motorcycle operator. A typical error made by the operator is veering wide on a turn
1
1-1
SAFETY INFORMATION
due to EXCESSIVE SPEED or undercornering (insufficient lean angle for the speed).
1
• Always obey the speed limit and
never travel faster than warranted by road and traffic conditions.
• Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
● The posture of the operator and
passenger is important for proper
control.
• The operator should keep both
hands on the handlebar and
both feet on the operator footrests during operation to maintain control of the motorcycle.
• The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.
• Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.
● Never ride under the influence of
alcohol or other drugs.
● This motorcycle is designed for on-
road use only. It is not suitable for
off-road use.
Protective apparel
The majority of fatalities from motorcycle accidents are the result of head
injuries. The use of a safety helmet is
the single most critical factor in the prevention or reduction of head injuries.
● Always wear an approved helmet.
● Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impairment
of vision that could delay seeing a
hazard.
● The use of a jacket, heavy boots,
trousers, gloves, etc., is effective in
preventing or reducing abrasions
or lacerations.
● Never wear loose-fitting clothes,
otherwise they could catch on the
control levers, footrests, or wheels
and cause injury or an accident.
● Never touch the engine or exhaust
system during or after operation.
They become very hot and can
cause burns. Always wear protective clothing that covers your legs,
ankles, and feet.
● A passenger should also observe
the above precautions.
Modifications
Modifications made to this motorcycle
not approved by Yamaha, or the removal of original equipment, may render the motorcycle unsafe for use and
may cause severe personal injury.
Modifications may also make your
motorcycle illegal to use.
Loading and accessories
Adding accessories or cargo to your
motorcycle can adversely affect stability and handling if the weight distribution
of the motorcycle is changed. To avoid
the possibility of an accident, use extreme caution when adding cargo or
accessories to your motorcycle. Use
extra care when riding a motorcycle
that has added cargo or accessories.
Here are some general guidelines to
follow if loading cargo or adding accessories to your motorcycle:
1-2
SAFETY INFORMATION
Loading
The total weight of the operator, passenger, accessories and cargo must
not exceed the maximum load limit.
Maximum load:
211 kg (465 lb) (CAL)
212 kg (467 lb) (U49)
When loading within this weight limit,
keep the following in mind:
● Cargo and accessory weight
should be kept as low and close to
the motorcycle as possible. Make
sure to distribute the weight as
evenly as possible on both sides of
the motorcycle to minimize imbalance or instability.
● Shifting weights can create a sud-
den imbalance. Make sure that accessories and cargo are securely
attached to the motorcycle before
riding. Check accessory mounts
and cargo restraints frequently.
● Never attach any large or heavy
items to the handlebar, front fork,
or front fender. These items, including such cargo as sleeping
bags, duffel bags, or tents, can
create unstable handling or a slow
steering response.
Accessories
Genuine Yamaha accessories have
been specifically designed for use on
this motorcycle. Since Yamaha cannot
test all other accessories that may be
available, you must personally be responsible for the proper selection, installation and use of non-Yamaha
accessories. Use extreme caution
when selecting and installing any accessories.
Keep the following guidelines in mind,
as well as those provided under “Load-
ing” when mounting accessories.
● Never install accessories or carry
cargo that would impair the perfor-
mance of your motorcycle. Care-
fully inspect the accessory before
using it to make sure that it does
not in any way reduce ground
clearance or cornering clearance,
limit suspension travel, steering
travel or control operation, or obscure lights or reflectors.
• Accessories fitted to the handlebar or the front fork area can
create instability due to improper
weight distribution or aerodynamic changes. If accessories
are added to the handlebar or
front fork area, they must be as
lightweight as possible and
should be kept to a minimum.
• Bulky or large accessories may
seriously affect the stability of
the motorcycle due to aerodynamic effects. Wind may attempt to lift the motorcycle, or
the motorcycle may become unstable in cross winds. These accessories may also cause
instability when passing or being
passed by large vehicles.
• Certain accessories can displace the operator from his or
her normal riding position. This
improper position limits the freedom of movement of the opera-
1
1-3
SAFETY INFORMATION
tor and may limit control ability,
therefore, such accessories are
not recommended.
1
● Use caution when adding electri-
cal accessories. If electrical accessories exceed the capacity of the
motorcycle’s electrical system, an
electric failure could result, which
could cause a dangerous loss of
lights or engine power.
Gasoline and exhaust gas
● GASOLINE IS HIGHLY FLAMMA-
BLE:
• Always turn the engine off when
refueling.
• Take care not to spill any gasoline on the engine or exhaust
system when refueling.
• Never refuel while smoking or in
the vicinity of an open flame.
● Never start the engine or let it run
for any length of time in a closed
area. The exhaust fumes are poisonous and may cause loss of
consciousness and death within a
short time. Always operate your
motorcycle in an area that has adequate ventilation.
● Always turn the engine off before
leaving the motorcycle unattended
and remove the key from the main
switch. When parking the motorcycle, note the following:
• The engine and exhaust system
may be hot, therefore, park the
motorcycle in a place where pedestrians or children are not likely to touch these hot areas.
• Do not park the motorcycle on a
slope or soft ground, otherwise it
may fall over.
• Do not park the motorcycle near
a flammable source, (e.g., a kerosene heater, or near an open
flame), otherwise it could catch
fire.
● When transporting the motorcycle
in another vehicle, make sure that
it is kept upright. If the motorcycle
should lean over, gasoline may
leak out of the fuel tank.
● If you should swallow any gaso-
line, inhale a lot of gasoline vapor,
or allow gasoline to get into your
eyes, see your doctor immediately.
If any gasoline spills on your skin
1-4
or clothing, immediately wash the
affected area with soap and water
and change your clothes.
Location of important labels
Please read the following important labels carefully before operating this vehicle.
SAFETY INFORMATION
EAU10381
1
1-5
SAFETY INFORMATION
1
1 California only
2 California only
3 California only
4
LOAD LIMIT
3 kg (7 lbs)
3TB-24877-A0
5
LOAD LIMIT
1 kg (2 lbs)
4BR-24877-A0
1-6
SAFETY INFORMATION
1
6
7
9
10
8
CAUTION
Cleaning with alkaline or
acid cleaner, gasoline or
solvent will damage
windshield.
Use neutral detergent.
5JW-00
270 kPa, {2.70 kgf/cm2}, 39psi
290 kPa, {2.90 kgf/cm2}, 42psi
270 kPa, {2.70 kgf/cm2}, 39psi
290 kPa, {2.90 kgf/cm2}, 42psi
3P6-21668-00
1-7
DESCRIPTION
Left view
2
EAU10410
1. Accessory box (page 3-18)
2. Front fork spring preload adjusting bolt (page 3-21)
3. Front fork rebound damping force adjusting knob (page 3-21)
4. Owner’s tool kit (page 6-1)
5. Rider seat (page 3-14)
6. Passenger seat (page 3-14)
7. Final gear oil filler bolt (page 6-15)
8. Final gear oil drain bolt (page 6-15)
9. Shock absorber assembly spring preload adjusting lever (page 3-23)
10.Air filter element (page 6-18)
11.Shift pedal (page 3-11)
12.Engine oil filler cap (page 6-13)
13.Engine oil filter cartridge (page 6-13)
14.Engine oil level check window (page 6-13)
2-1
Right view
DESCRIPTION
EAU10420
2
1. Storage compartment (page 3-18)
2. Fuel tank cap (page 3-12)
3. Fuse box (page 6-33)
4. Windshield (page 3-8)
5. Battery (page 6-32)
6. Main fuse (page 6-33)
7. Front fork compression damping force adjusting screw (page 3-21)
8. Brake pedal (page 3-11)
9. Shock absorber assembly rebound damping force adjusting knob
(page 3-23)
10.Rear brake fluid reservoir (page 6-25)
2-2
DESCRIPTION
Controls and instruments
2
EAU10430
1. Rear view mirror (page 3-21)
2. Clutch lever (page 3-10)
3. Left handlebar switches (page 3-8)
4. Clutch fluid reservoir (page 6-25)
5. Tachometer (page 3-3)
6. Speedometer (page 3-3)
7. Multi-function display (page 3-4)
8. Front brake fluid reservoir (page 6-25)
9. Right handlebar switches (page 3-8)
10.Brake lever (page 3-11)
11.Throttle grip (page 6-20)
12.Main switch/steering lock (page 3-1)
13.Headlight beam adjusting knob (page 3-19)
2-3
INSTRUMENT AND CONTROL FUNCTIONS
EAU10460
Main switch/steering lock
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
positions are described below.
EAU35921
ON
All electrical circuits are supplied with
power, and the meter lighting, taillights,
license plate light and position lights
come on, and the engine can be started. The key cannot be removed.
NOTE:
The headlights come on automatically
when the engine is started and stay on
until the key is turned to “OFF”, even if
the engine stalls.
OFF
EAU10660
All electrical systems are off. The key
can be removed.
EAU10690
LOCK
The steering is locked, and all electrical
systems are off. The key can be removed.
To lock the steering
1. Push.
2. Turn.
1. Turn the handlebars all the way to
the left or right.
2. Push the key in from the “OFF” position, and then turn it to “LOCK”
while still pushing it.
3. Remove the key.
To unlock the steering
3
1. Push.
2. Turn.
Push the key into the main switch, and
then turn it to “OFF” while still pushing
it.
EWA10060
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving,
otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident. Make
sure that the vehicle is stopped before turning the key to “OFF” or
“LOCK”.
3-1
INSTRUMENT AND CONTROL FUNCTIONS
Indicator and warning lights
3
1. Left turn signal indicator light “”
2. Right turn signal indicator light “”
3. Engine trouble warning light “”
4. Anti-lock Brake System (ABS) warning light
“”
ABS
5. Neutral indicator light “”
6. High beam indicator light “”
7. Oil level warning light “”
Turn signal indicator lights “” and
“”
The corresponding indicator light flashes when the turn signal switch is
pushed to the left or right.
EAU11003
EAU11030
Neutral indicator light “”
EAU11060
This indicator light comes on when the
transmission is in the neutral position.
EAU11080
High beam indicator light “”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAU11120
Oil level warning light “”
This warning light comes on when the
engine oil level is low.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on
for a few seconds, then go off, have a
Yamaha dealer check the electrical circuit.
NOTE:
Even if the oil level is sufficient, the
warning light may flicker when riding on
a slope or during sudden acceleration
or deceleration, but this is not a malfunction.
3-2
Engine trouble warning light “”
EAU11530
This warning light comes on or flashes
when an electrical circuit monitoring the
engine is defective. When this occurs,
have a Yamaha dealer check the selfdiagnosis system. (See page 3-4 for an
explanation of the self-diagnosis device.)
The electrical circuit of the warning light
can be checked by turning the key to
“ON”. If the warning light does not come
on for a few seconds, then go off, have
a Yamaha dealer check the electrical
circuit.
ABS warning light “”
ABS
EAU39500
If this warning light comes on or flashes
while riding, the ABS may be defective.
If this occurs, have a Yamaha dealer
check the system as soon as possible.
(See page 3-12.)
EWA10081
WARNING
If the ABS warning light comes on or
flashes while riding, the brake system reverts to conventional braking.
Therefore, be careful not to cause
the wheels to lock during emergen-
INSTRUMENT AND CONTROL FUNCTIONS
cy braking. If the warning light
comes on or flashes while riding,
have a Yamaha dealer check the
brake system as soon as possible.
The electrical circuit of the warning light
can be checked by turning the key to
“ON”.
If the warning light does not come on or
remains on, have a Yamaha dealer
check the electrical circuit.
EAU11601
Speedometer
1. Tachometer
2. Speedometer
3. Multi-function display
The speedometer shows the riding
speed.
When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then return
to zero in order to test the electrical circuit.
EAU11872
Tachometer
3
1. Tachometer
2. Tachometer red zone
The electric tachometer allows the rider
to monitor the engine speed and keep it
within the ideal power range.
When the key is turned to “ON”, the ta-
chometer needle will sweep once
across the r/min range and then return
to zero r/min in order to test the electrical circuit.
ECA10031
CAUTION:
Do not operate the engine in the tachometer red zone.
Red zone: 9000 r/min and above
3-3
INSTRUMENT AND CONTROL FUNCTIONS
Multi-function display
3
1. Multi-function display
2. “SELECT” button
3. “RESET” button
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function display.
The multi-function display is equipped
with the following:
● an odometer (which shows the to-
tal distance traveled)
● two tripmeters (which show the
distance traveled since they were
last set to zero)
EAU40290
EWA14430
● a fuel reserve tripmeter (which
shows the distance traveled on the
fuel reserve)
● a clock
● a fuel meter
● a coolant temperature meter
● a transmission gear display
● an ambient temperature display
● a fuel consumption display (instan-
taneous and average consumption
functions)
● a self-diagnosis device
NOTE:
Be sure to turn the key to “ON” before
using the “SELECT” and “RESET” buttons.
Odometer and tripmeter modes
1. Odometer/tripmeter/fuel reserve tripmeter
2. “SELECT” button
3. “RESET” button
Pushing the “SELECT” button switches
the display between the odometer
mode “ODO” and the tripmeter modes
“TRIP 1” and “TRIP 2” in the following
order:
ODO → TRIP 1 → TRIP 2 → ODO
NOTE:
When selecting “TRIP 1” or “TRIP 2”,
the display flashes for five seconds.
When approximately 5.5 L (1.45 US
gal) (1.21 Imp.gal) of fuel remains in the
fuel tank, the display will automatically
change to the fuel reserve tripmeter
mode “F-TRIP” and start counting the
3-4
INSTRUMENT AND CONTROL FUNCTIONS
distance traveled from that point. In that
case, pushing the “SELECT” button
switches the display between the various tripmeter and odometer modes in
the following order:
F-TRIP → TRIP 1 → TRIP 2 → ODO →
F-TRIP
To reset a tripmeter, select it by pushing the “SELECT” button, and then
push the “SELECT” button for at least
one second. If you do not reset the fuel
reserve tripmeter manually, it will reset
itself automatically and the display will
return to the prior mode after refueling
and traveling 5 km (3 mi).
Clock
To set the clock:
1. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
2. When the hour digits start flashing,
push the “RESET” button to set the
hours.
3. Push the “SELECT” button, and
the minute digits will start flashing.
4. Push the “RESET” button to set
the minutes.
5. Push the “SELECT” button and
then release it to start the clock.
Fuel meter
wards “E” (Empty) as the fuel level
decreases. When the last segment
starts flashing, refuel as soon as possible. When the key is turned to “ON”, all
of the display segments of the fuel
meter will appear one after the other
and then disappear in order to test the
electrical circuit.
NOTE:
This fuel meter is equipped with a selfdiagnosis system. If the electrical circuit
is defective, all the display segments
will start flashing. If this occurs, have a
Yamaha dealer check the electrical circuit.
Coolant temperature meter
3
1. Clock
2. “SELECT” button
3. “RESET” button
1. Fuel meter
The fuel meter indicates the amount of
fuel in the fuel tank. The display segments of the fuel meter disappear to-
3-5
1. Coolant temperature meter
INSTRUMENT AND CONTROL FUNCTIONS
With the key in the “ON” position, the
coolant temperature meter indicates
the temperature of the coolant. When
the key is turned to “ON”, all of the display segments of the coolant temperature meter will appear one after the
other and then disappear in order to
test the electrical circuit. The coolant
3
temperature varies with changes in the
weather and engine load. If the top segment flashes, stop the vehicle and let
the engine cool. (See page 6-38.)
CAUTION:
Do not operate the engine if it is
overheated.
ECA10020
Transmission gear display
1. Transmission gear display
2. Neutral indicator light “”
This display shows the selected gear.
The neutral position, however, is not
displayed, it is indicated by the neutral
indicator light.
Ambient temperature, instantaneous fuel consumption and average fuel consumption modes
1. Ambient temperature/instantaneous fuel
consumption/average fuel consumption
2. “SELECT” button
3. “RESET” button
Push the “RESET” button to switch the
display between the ambient temperature mode “Air”, the instantaneous fuel
consumption mode “MPG” and the average fuel consumption mode “AV_ _
MPG” in the following order:
Air → MPG → AV_ _ MPG → Air
3-6
INSTRUMENT AND CONTROL FUNCTIONS
Ambient temperature mode
1. Ambient temperature
This display shows the ambient temperature from 16 °F to 122 °F in 1 °F increments. The temperature displayed
may vary from the ambient temperature.
NOTE:
● If the ambient temperature falls be-
low 16 °F, a lower temperature
than 16 °F will not be displayed.
● If the ambient temperature climbs
above 122 °F, a higher temperature than 122 °F will not be displayed.
● The accuracy of the temperature
reading may be affected when
riding slowly [approximately under
20 km/h (12.5 mi/h)] or when
stopped at traffic signals, railroad
crossings, etc.
Instantaneous fuel consumption mode
1. Instantaneous fuel consumption
This display shows the distance that
can be traveled on 1.0 US.gal of fuel
under the current riding conditions.
NOTE:
If traveling at speeds under 10 km/h
(6.0 mi/h), “_ _” will be displayed.
Average fuel consumption mode
3
1. Average fuel consumption
This display shows the average fuel
consumption since it was last reset.
When the average fuel consumption
mode is selected, the display flashes
for five seconds, and then “AV _ _
MPG” (average distance that can be
traveled using 1.0 US.gal of fuel) is displayed.
NOTE:
● To reset the average fuel con-
sumption display, push the “RE-
SET” button to select the mode
again, and then push the “RESET”
button for 1 second while the display is flashing.
3-7
INSTRUMENT AND CONTROL FUNCTIONS
● After resetting the average fuel
consumption display, “_ _” will be
shown for that display until the vehicle has traveled 1 km (0.6 mi).
CAUTION:
If there is a malfunction, “– –” will be
displayed. Have a Yamaha dealer
3
check the vehicle.
Self-diagnosis device
1. Error code display
This model is equipped with a self-diagnosis device for various electrical circuits.
If any of those circuits are defective, the
multi-function display will indicate a
two-digit error code (e.g., 11, 12, 13).
ECA15471
If the multi-function display indicates
such an error code, note the code number, and then have a Yamaha dealer
check the vehicle.
ECA11790
CAUTION:
If the multi-function display indicates an error code, the vehicle
should be checked as soon as possible in order to avoid engine damage.
3-8
EAU12344
Handlebar switches
Left
1. Windshield position adjusting switch “”
2. Dimmer switch “ / ”
3. Turn signal switch “ / ”
4. Horn switch “”
INSTRUMENT AND CONTROL FUNCTIONS
Right
1. Engine stop switch “ / ”
2. Hazard switch “”
3. Start switch “”
EAU12400
Dimmer switch “ / ”
Set this switch to “” for the high
beam and to “” for the low beam.
EAU12460
Turn signal switch “ / ”
To signal a right-hand turn, push this
switch to “”. To signal a left-hand
turn, push this switch to “”. When re-
leased, the switch returns to the center
position. To cancel the turn signal
lights, push the switch in after it has returned to the center position.
Windshield position adjusting
EAU12493
switch “”
To move the windshield up, push this
switch in direction (a). To move the
windshield down, push the switch in direction (b).
1. Windshield position adjusting switch “”
NOTE:
When the key is turned to “OFF”, the
windshield will automatically return to
the lowest position.
EAU12500
Horn switch “”
Press this switch to sound the horn.
Engine stop switch “ / ”
EAU12660
Set this switch to “” before starting
the engine. Set this switch to “” to
stop the engine in case of an emergency, such as when the vehicle overturns
or when the throttle cable is stuck.
EAU12710
Start switch “”
Push this switch to crank the engine
with the starter.
ECA10050
CAUTION:
See page 5-1 for starting instructions prior to starting the engine.
EAU12764
Hazard switch “”
With the key in the “ON” position, turn
this switch to “” to turn on the hazard
lights (simultaneous flashing of all turn
signal lights).
The hazard lights are used in case of
an emergency or to warn other drivers
when your vehicle is stopped where it
might be a traffic hazard.
3
3-9
INSTRUMENT AND CONTROL FUNCTIONS
CAUTION:
Do not use the hazard lights for an
extended length of time with the engine not running, otherwise the battery may discharge.
3
ECA10061
EAU12830
Clutch lever
1. Clutch lever
2. Arrow mark
3. Clutch lever position adjusting dial
4. Distance between clutch lever and handlebar
grip
The clutch lever is located at the left
handlebar grip. To disengage the
clutch, pull the lever toward the handlebar grip. To engage the clutch, release
the lever. The lever should be pulled
rapidly and released slowly for smooth
clutch operation.
The clutch lever is equipped with a
clutch lever position adjusting dial. To
adjust the distance between the clutch
lever and the handlebar grip, turn the
adjusting dial while holding the lever
pushed away from the handlebar grip.
3-10
Make sure that the appropriate setting
on the adjusting dial is aligned with the
arrow mark on the clutch lever.
The clutch lever is equipped with a
clutch switch, which is part of the ignition circuit cut-off system. (See page
3-25.)
INSTRUMENT AND CONTROL FUNCTIONS
EAU12870
Shift pedal
1. Shift pedal
The shift pedal is located on the left
side of the engine and is used in combination with the clutch lever when
shifting the gears of the 5-speed constant-mesh transmission equipped on
this motorcycle.
EAU26822
Brake lever
The brake lever is located at the right
handlebar grip. To apply the front
brake, pull the lever toward the handlebar grip.
1. Brake lever
2. “” mark
3. Brake lever position adjusting dial
4. Distance between brake lever and handlebar
grip
The brake lever is equipped with a position adjusting dial. To adjust the distance between the brake lever and the
handlebar grip, turn the adjusting dial
while holding the lever pushed away
from the handlebar grip. Make sure that
the appropriate setting on the adjusting
dial is aligned with the “” mark on the
brake lever.
3-11
EAU39540
Brake pedal
3
1. Brake pedal
The brake pedal is on the right side of
the vehicle.
This model is equipped with a unified
brake system.
When pressing down on the brake pedal, the rear brake and a portion of the
front brake are applied. For full braking
performance, apply both the brake lever and the brake pedal simultaneously.
INSTRUMENT AND CONTROL FUNCTIONS
ABS
The Yamaha ABS (Anti-lock Brake
System) features a dual electronic control system, which acts on the front and
rear brakes independently. The ABS is
monitored by an ECU (Electronic Control Unit), which will have recourse to
3
manual braking if a malfunction occurs.
WARNING
● The ABS performs best on long
braking distances.
● On certain (rough or gravel)
roads, the braking distance may
be longer with than without the
ABS. Therefore, always keep a
sufficient distance to the vehicle
ahead to match the riding
speed.
NOTE:
● When the ABS is activated, the
brakes are operated in the usual
way. A pulsating action may be felt
at the brake lever or brake pedal,
but this does not indicate a malfunction.
EAU39530
EWA10090
● This ABS has a test mode which
allows the owner to experience the
pulsating at the brake lever or
brake pedal when the ABS is operating. However, special tools are
required, so please consult your
Yamaha dealer when performing
this test.
EAU13070
Fuel tank cap
1. Fuel tank cap lock cover
2. Unlock.
To open the fuel tank cap
Open the fuel tank cap lock cover, insert the key into the lock, and then turn
it 1/4 turn clockwise. The lock will be released and the fuel tank cap can be
opened.
To close the fuel tank cap
1. Push the fuel tank cap into position
with the key inserted in the lock.
2. Turn the key counterclockwise to
the original position, remove it, and
then close the lock cover.
3-12
Loading...