Yamaha DPX-1300-E Owners manual

DPX-1300

DIGITAL CINEMA PROJECTOR

PROJECTEUR CINEMA NUMERIQUE

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

• Explanation of Graphical Symbols The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

IMPORTANT!

Please record the serial number of this unit in the space below.

Model: Serial No.:

The serial number is located on the bottom of the unit. Retain this Owner’s Manual in a safe place for future reference.

1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the

manufacturer.

12 Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15 Be sure to allow spaces of at least 30cm above, behind and on

both sides the unit.

16 Do not place the following objects on this unit:

A vessel with water in it. If the vessel falls by vibrations and water spills, it may cause damage to the unit, and/or you may get an electric shock.

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation

Address: 6660 Orangethorpe Avenue

Buena Park, CA90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: Projector

Model Name: DPX-1300

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See the user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B” digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

We Want You Listening For A Lifetime

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

Caution: Read this before operating this unit.

•To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

Installation

• Install this unit in a well-ventilated, cool, dry, clean place with at least 30 cm (1 feet) clearance on the top, right and left, and at the back of this unit — away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.

• Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid.

• Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

• On the top of this unit, do not place:

– Other components, as they may cause damage and/or

discoloration on the surface of this unit.

– Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury.

– Containers with liquid in them, as they may cause electrical

shock to the user and/or damage to this unit.

• Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to restrict heat dissipation. If the temperature inside this unit rises too much, it may cause fire, damage to this unit, and/or personal injury.

•When installing this unit on the ceiling, make sure the ceiling has sufficient strength to support this unit and the ceiling mounts for an extended period of time. Installation must be performed only by qualified service personnel.

• Install this unit near the AC outlet and where the AC power plug can be reached easily.

Operation

• Remove the lens cover before starting any operation of this unit to prevent the heat from staying around the lens. Operation with the cap on may cause damage to this unit.

• Do not plug in this unit to a wall outlet until all connections are complete.

• Only the voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than that specified.

• Do not use force on switches, knobs and/or cords.

•Take care of this unit so that no foreign objects and/or liquid drop inside this unit.

•To prevent damage by lightning, keep the power cord out and outdoor antennas disconnected from a wall outlet or te unit during the lightning storm.

• Do not look into the lens while this unit is turned on. It may cause serious damage to your eyesight.

• Before moving this unit, press STANDBY/ON to set this unit in the standby mode, and disconnect the AC power plug from the wall outlet.

• Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reason.

• When not planning to use this unit for a long period of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

•When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cable.

• Be sure to read the “Troubleshooting” section on common operating errors before concluding that this unit is faulty.

Others

• Clean the lens carefully so as not to create any scratches by using a blower or lens paper.

•Replace the lamp when the LAMP warning indicator blinks in red after the lamp usage has exceeded 2000 hours. Follow the lamp replacement procedure described in this manual.

For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note

•The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

IMPORTANT

THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW: EARTH BLUE: NEUTRAL BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN or GREENand-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

For Canadian customers

To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-

003.

English

iii

Table of contents

1 Getting started 2

Inappropriate places for installation ....... 2

Accessory check .................................... 2

2 Features 3

3 Controls and functions 4

4 Remote control 6

5 Preparation 10

6 Installation 12

Setting up the DPX-1300 ..................... 12

Projection distance ............................... 13

Projection image position ..................... 14

7 Connection 15

Connecting to AV components............. 15

Connecting to computer devices ......... 16

8 Projection 17

Getting started

Features

Controls and functions

Remote control

Preparation

Installation

Connection

Checking installation and connections...

Turning the projector power on ............ 18

Selecting an input signal ...................... 20

Adjusting the image ............................. 25

9 Menu 27

Menu configurations ............................ 27

Menu items .......................................... 28

Menu operations .................................. 38

Memory function

(Saving, Recall, Lock, Copy, Reset) 48

Reference 55

Glossary ............................................... 55

Compatible signal types ....................... 56

Maintenance ......................................... 58

Troubleshooting.................................... 60

Message display .................................. 62

LED Indicator meanings ....................... 63

Specifications ....................................... 64

Dimensional drawing ............................ 65

Projection

Memory function

Reference

English

1 Getting started

◆Inappropriate places for installation

If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place to install this unit by avoiding the places listed below.

1. Places where the temperature and humidity vary greatly

• Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely low.

• This unit must be used within a temperature range of 5 to 35°C.

2. Places without adequate ventilation

• Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.

• Do not cover the ventilation slots of this unit. Covering the slots will obstruct heat dissipation.

• Install this unit on the firm surface.

• Do not cover this unit with a tablecloth, etc.

• Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.

• If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.

3. Places where it gets dusty

• If the filter is blocked with dust, the temperature of this unit may become too high.

4. Places with too much vibration or impact

•Vibration and impact can damage parts of this unit.

5. Places where this unit gets exposed to water or high humidity

• If this unit is exposed to water or high humidity, it may cause a fire or electrical shock.

6. Unstable places

• If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.

7. In close proximity to a Radio or Stereo

•The unit may interfere with reception if placed in close proximity to a radio or television receiver.

Warning

•To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.

◆Accessory check

Please check that all accessories listed here are included in your package.

• Remote control • Batteries (AA, UM-3 or R6) • Power cable

AUTO

ZOOM FOCUSV. POS

PATTIRIS

SETTING

ESCAPE

• Trigger-out DC plug (For USA only)

ASPECT

RESET

STILL

INPUT

S VIDEO

VIDEO

MEMORY

123

INPUT

HIDE

LIGHT

HDMI

DVI

• Pin/BNC adapters • Lens cap

2 Features

Highly configurable electronic adjustment gives you the freedom to place the projector wherever you want

A short focal length, high power zoom, and fully vertically adjustable lens allow you to use the projector in a wide range of environments. You can also use the remote control to access many lens functions such as focus, zoom, and lens shift to fine-tune the projector from your viewing position.

Features

Uses the DMDTM device 720p DarkChip3

The projector uses the high contrast “720p DarkChip3TM”, to reduce black levels even further and reproduce contrasts close to that of a film.

Adjust 7 colors independently (including white), or use the automatic color balance function

The DPX-1300 allows you to adjust the 7-axis WRGBYCM color coordinate and gain parameters directly. For better consistency, you can also control color temperature and RGB balance together, allowing you to check that the changes you make are always consistent with your preferences.

The digital interface provides sharp, detailed images

The DPX-1300 is equipped with an HDMI terminal, which is set to become the standard for the coming generation of products. Connect to a DVD player or set-top box with a HDMI terminal to receive digital image data directly, and enjoy completely digitally processed images. Compatible with the content protection function of HDCP.

Intelligent memory functions

The DPX-1300 can store six image memory settings, called memory numbers, for each input jack. For each memory number, you can set parameters for different input resolutions, and the unit will switch to the appropriate parameters when it begins displaying an image of an appropriate resolution. For example, the unit automatically changes display settings without changing memory numbers when you change from watching a DVD to watching a HDTV image for which you have set different image menu item parameters.

In-line menus for image adjustment

You can access image adjustment menu items at the touch of a button, and adjust images while viewing them without opening the menu screen.

English

3 Controls and functions

◆Main unit <Front panel and controls>

Front remote control sensor

Exhaust vent

Lens cap

Adjustable feet

Makes small adjustments to the projection angle

Lens

STANDBY/ON indicator

1 2

3 4

PATTERN

Lamp cover

Ventilation inlet

STANDBY/ON

ESCAPE

ASPECT

LAMP COVER TEMP FAN

DIGITAL CINEMA PROJECTOR DPX-1300

INPUT

SETTING

6 7 8

9 0

1 LED Indicators

The main unit is equipped with 5 indicators to display various states of operation. See page 63 for explanations of the LED indicator meanings.

PATTERN

2 STANDBY/ON button

Switches the unit between Standby and On (operational) modes.

3 ESCAPE button

Exits from submenus.

4 PATTERN button

Switches the built-in test pattern on and off.

5 ASPECT button

Turns the display aspect menu for the project image on and off.

STANDBY/ON

A STANDBY/ON indicator

(There is also an LED on the front panel of the main unit.)

ESCAPE

ASPECT

LAMP COVER TEMP FAN

SETTING

INPUT

B LAMP warning indicator

C COVER warning indicator

D TEMP warning indicator

E FAN warning indicator

7 MENU button

Switches the settings and adjustments menu display on and off.

8 SETTING button

Selects lens adjustment modes.

9 INPUT button

Switches the input signal selection menu display on and off.

0 Cursor buttons

Use the h, g, +, - buttons for system operations, menu item selection, and changing system values.

6 (Enter) button

Sets values when the DPX-1300 is displaying the menu. When the menu is not displayed, the DPX-1300 displays the in-line image quality adjustment menu. (☞ page 47)

◆Main unit <Rear panel / Connections>

Rear remote control sensor

Controls and functions

HDMIDVI

D4 VIDEO

RGB/YP

INPUT B

BPR

/YCBC

1 INPUT B (D-sub 15 pin)

Receives component video and RGB (RGB/YPBPR/YCBCR) signals. Use a D-sub monitor cable to connect components to this jack.

2 D4 VIDEO (D jack)

Receives signals output from the D jacks of other AV components. It is compatible with D1 - D4 formats.

3 - 7 INPUT A (BNC jacks)

Receive component video and RGB signals. Connect component signal connectors from AV components to input jacks 3 - 5, and RGB signal connectors from computers to input jacks 3 - 7. Use BNC cables for these connections. 3 G/Y (G, or luminance signal)

B/CB (B, or color difference signal)

4 B/P 5 R/PR/CR (R, or color difference signal) 6 HD/SYNC (Horizontal sync signal, composite sync signal) 7 VD (Vertical sync signal)

8 S VIDEO (Mini DIN jack)

Receives signals from S-VIDEO output jacks of other AV components. Use an S-VIDEO cable for these connections.

INPUT A

G/Y B/PB/CBR/PR/C

ert

OUT IN

REMOTE

HD/SYNC

765432190

RS-232C

S VIDEO VIDEO

TRIGGER OUT

9 AC inlet

Insert the supplied AC power cable here.

0 VIDEO (Pin Jack)

Receives composite video signals from the VIDEO output jacks of other AV components. Use a video pin cable for these connections.

q DVI (DVI jack)

Receives RGB signals from computers or AV components. Use a DVI cable for this connection.

w HDMITM (HDMITM jack)

Receives HDMITM signals from computers or AV components.

e REMOTE IN / OUT jack

Connect the remote control to the REMOTE IN jack if you want to use it through a cable. The REMOTE OUT jack outputs the signal received through the REMOTE IN jack without any change.

r RS-232C (D-sub 9 pin)

For use in servicing this unit.

t TRIGGER OUT

Outputs control signals to external components. This output provides a potential of 12 V/ maximum 200 mA when this unit is projecting. Use the supplied trigger-out DC plug (for US model only) to control external components.

English

4 Remote control

◆ Remote control functions

Buttons on the remote control with identical names to those on the main unit perform identical functions. When using the remote control, point it at the remote control sensor on the front or back of the main unit from a distance of 7m (23 feet) or less.

1 Transmit indicator

Lights up when the remote control sends infrared signals to the

AUTO

ESCAPE

ZOOM FOCUSV. POS

SETTING

PATTIRIS

main unit.

2 AUTO button

Automatically sets the DPX-1300 to the best settings for the type of signal it is currently receiving.

3 V.POS button

Switches on or off the vertical adjustment mode for the entire image.

4 ZOOM button

Switches on or off the size adjustment mode for the image the DPX-1300 is projecting.

5 IRIS button

Switches on or off the lens iris change mode.

6 ESCAPE button

Exits from submenus.

ASPECT

RESET

LIGHT

HDMI

STILL

INPUT

S VIDEO

VIDEO

MEMORY

123

INPUT

HIDE

DVI

7 Cursor buttons

Use the h ,g, +, - buttons to move the cursor within the onscreen display.

8 ASPECT button

Turns the display aspect menu for the project image on and off.

9 RESET button

Resets all adjustable parameters to their default settings.

0 STILL button

Stops a moving image, displaying a still of the image the DPX1300 is projecting. Press STILL again to cancel this effect.

q INPUT area

Selects the INPUT jacks directly.

w MEMORY area

Calls stored memory (all parameter settings) directly.

e button

Switches the unit between Standby and On (operational) modes.

r FOCUS button

Switches on or off the focus adjustment mode for the image the DPX-1300 is projecting.

t PATT (PATTERN) button

Switches on and off the built-in test pattern.

y MENU button

Switches on and off the settings and adjustments menu display.

u (Enter) button

Sets values when the DPX-1300 is displaying the menu. When the menu is not displayed, the DPX-1300 displays the in-line image quality adjustment menu. (☞ page 47)

i INPUT button

Switches on and off the input signal selection menu display.

o LIGHT switch

Moving this switch lights the high-use AUTO (2), ESCAPE (6), ASPECT(8) ,

(e), MENU (y), and INPUT (i) buttons. The light disappears if you do not perform any operation within 10 seconds.

p HIDE button

Temporarily halts projection of the image the DPX-1300 is currently displaying. Press again to cancel this effect.

a Remote control code switch

Selects ID-1 or ID-2 when operating two main units with one remote control. You can set the ID for the main unit in the menu (The default setting is ID-1).

s Remote control cable jack

Connect this jack and REMOTE IN jack on the main unit using a cable (commercially available) to use the remote control with a wired connection. (☞ page 8)

.POS

RIS

SCAPE

ASPECT

RESET

S VIDEO

INPUT

VIDEO

MEMORY

HDMI

DVI

LIGHT

INPUT

PATT

D-2

Remote control

English

◆Loading the batteries into the remote control

1. Remove the battery compartment cover.

2. Insert two batteries (AA, UM3, or R6 type), matching the polarity markings on the batteries with those in the battery compartment.

3. After loading the batteries, close the cover until it snaps into

place.

Warning

• If the remote control must be used closer to the main unit than normal, or does not always operate correctly, exchange the

batteries for new ones.

• Do not mix old and new, or different types of batteries.

• Remove the batteries if you do not plan to use the unit for a long time.

• If the batteries leak, dispose of them immediately, taking care not to touch the battery fluid. If the battery fluid comes into contact

with your eyes, mouth, or skin, rinse it off with water immediately and consult a doctor. Clean the battery compartment thoroughly before installing new batteries.

◆Using the remote control with a wired connection

Use a 2P monaural miniplug cable (commercially available) to connect the remote control jack on the underside of the remote control to the REMOTE IN jack on the main unit. Use the wired remote control configuration to control the DPX-1300 without having to be within range of the remote sensor.

ESET

STIL

V IDE

INPU

VID

E O

INPUT

V .P

ZOOM

FOCUS

CAPE

T T

PAT

-1

P ECT

IDE

LIGH

RGB/YPBPR/YCBC

HDMIDVI

INPUT B

B/CB

D4 VIDEO

G/Y B/P

OUT IN

TRIGGER OUT

RS-232C

REMOTE

INPUT A

R/PR/C

HD/SYNC VD

S-VIDEO VIDEO

◆ Limits for using the remote control

Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits described here.

Distance to sensor Angle to sensor

7 m 30˚ vertically and horizontally

(approximate value) (approximate value)

OUT IN

HDMI

INPUT B

G/Y B/PB/CBR/PR/C

D4 VIDEO

RGB/YP

BPR

/YCBC

TRIGGER OUT

RS-232C

REMOTE

INPUT A

HD/SYNC

S-VIDEO VIDEO

AUTO

ZOOM FOCUSV. POS

PATTIRIS

SETTING

ESCAPE

INPUT

ASPECT

RESET

HIDE

LIGHT

STILL

INPUT

S VIDEO

HDMI

VIDEO

BDVI

MEMORY

123

AUTO

ZOOM FOCUSV. POS

PATTIRIS

SETTING

ESCAPE

INPUT

ASPECT

RESET

HIDE

LIGHT

STILL

INPUT

S VIDEO

HDMI

VIDEO

B DVI

MEMORY

123

Use within a left/right arc of 30 degrees Use within a vertical arc of 30 degrees

Warning

• Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control.

• Objects placed between the main unit remote sensor and the remote control may block the remote control signal and inhibit functioning.

Remote control

English

Preparation

Before projection, install the main unit and a screen, connect the main unit to an AV component or computer, and adjust the projection image. You can begin projection as soon as installation is complete. Refer to the sections below for information on how to install the main unit to suit your viewing environment.

◆If you have not installed the main unit or screen

• Immediately after purchase, when you have not installed either the main unit or a screen.

• When moving the main unit and screen to a new location.

STEP 1

Install the main unit and screen. ☞ page 12

STEP2

Connect AV components or a computer to the main unit. ☞ page 15 - 16

STEP3

Select an image and project. ☞ page 17 - 26

• The image is used for adjusting the image position and focus.

STEP4

Adjust the projection image. ☞ page 27 - 47

• Use the menu to adjust projection details.

Projection

preparations

complete

◆If you have installed the main unit and screen, but not connected

any image playback components

• You have installed the main unit and screen, but not connected any source components.

• You are using the main unit in a previously installed location, and wish to change the component you use as a signal source.

STEP2

Connect AV components or a computer to the main unit. ☞ page 15 - 16

STEP3

Select an image and project. ☞ page 17 - 26

• The image is used for adjusting the image position and focus.

STEP4

Adjust the projection image. ☞ page 27 - 47

• Use the menu to adjust projection details.

Projection

preparations

complete

◆If you have installed the main unit and screen, and connected a

source component

• You have installed the main unit and screen, and connected source components.

• You are using the main unit in a previously installed location with previously connected source components.

You do not need to carry out step 3 or step 4 if you do not want to adjust the projection image. If the unit does not project the image correctly, it may not be connected correctly. In this case, carry out this procedure starting from step 2.

STEP3

Select an image and project. ☞ page 17 - 26

• The image is used for adjusting the image position and focus.

STEP4

Adjust the projection image. ☞ page 27 - 47

• Use the menu to adjust projection details.

Projection

preparations

complete

Step1

Set up the projector and screen

• Install the projector

• Install the screen ☞ page 12 - 14

Step2

Connect an AV component or computer

• Connect AV components

• Connect a computer ☞ page 15 - 16

Step3

Turn the power on and selecting an image for projection

•Turn on the projector power

•Begin playback of the input image

• Select an input signal

• Select a projection image aspect

• Adjust the image Focus/Vertical and Horizontal position/Size/Iris

☞ page 17 - 26

Prepararion

Step4

Use the menu to adjust the image quality and other parameters

• Image quality: Set image quality details

• Signal setting: Set input signal details

• Default settings: Set the default settings for everyday use

• Installation settings: Set to suit your viewing environment ☞ page 27 - 47

Only adjust these parameters when necessary. It is not necessary to adjust these settings once you have set them initially.

English

Installation

There are four ways of mounting the projector.

Setting up the DPX-1300

Mounting method

Placed on a table

Mounted on the ceiling

A: From in front of a screen B: From behind a semi-translucent screen C: From in front of a screen D: From behind a semi-translucent screen

Projection method

◆ Mounting the projector on a table

A: From in front of a screen

Place the unit on a table to project and view the image from in front of the screen. Usually, place the unit on a reasonably high table. The height from the bottom of the unit to the center of the lens is 12.4 cm (4”-7/8).

B: From behind a screen (using a semi-translucent screen)

Place the unit on a table to project and view the image from behind a semi-translucent screen. The distance between the projector and the screen should be the same as “A: From in front of the screen”.

• Set the [Location] menu item in the [Setup] menu group to [Rear/Table]. (☞ page 27 - 47)

◆ Mounting the projector on the ceiling

There are two kinds of brackets (sold separately: PMT-L31 and PMT-H35), which you can use to mount the projector on the ceiling. Please consult your dealer for details on their use, and have installation done by either your dealer or a reputable contractor.

C: From in front of a screen

Mount the unit on the ceiling to project and view the image from in front of the screen. The distance between the projector and the screen should be the same as “A: From in front of the screen”.

Set the [Location] menu item in the [Setup] menu group to [Front/Ceiling]. (☞ page

•

D: From behind a semi-translucent screen

Mount the unit on the ceiling to project and view the image from behind a semi-translucent screen. The distance between the projector and the screen should be the same as “B: From behind a screen”.

Set the [Location] menu item in the [Setup] menu group to [Rear/Ceiling]. (☞ page

•

27 - 47

)

Projection distance

The most suitable distance between the screen and the projector (see Projection distance [a]) depends on the size of the screen (diagonal length) you use. You can use the zoom function to adjust the projection distance within a preset range from Wide to Tele. You can also alter the V.POS parameter to adjust the vertical position of the image to better suit the screen. Use the information in the table below to determine the best location to place the projector in to suit your screen size.

Screen size

(inch)

60 70 80

90 100 110 120 150 200

Projection distance [a]

Wide (m) – Tele (m)

1.78 – 2.88

2.08 – 3.37

2.39 – 3.86

2.70 – 4.35

3.00 – 4.84

3.31 – 5.33

3.62 – 5.82

4.54 – 7.29

6.07 – 9.74

Projection distance [a]

Lens

60'' 80'' 100'' 150'' 200''

centerline

Installation

Screen size

*These are theoretical values.

During actual use there may be a deviance of a few percent.

Since the DPX-1300 has a 16:9 panel, the ideal installation location for use with a 4:3 screen depends on the size of the image you wish to view.

Screen size

(inch)

80 100 120 200

(*1) Projects a 16:9 image that completely fills the screen (leaves a black line at the top and bottom of the screen). (*2) Projects a 4:3 image that completely fills the screen. (*3) When projecting both 16:9 and 4:3 images.

You can use the zoom function to make efficient use of the screen for both *1 and *2 above. The projection distance in this case is between Wide in *2 and Tele in *1. Use the zoom to adjust the size of the projection images so that they fill the screen completely. Note that adjustments to V.POS may cause the position of the image to change.

16:9 image (*1)

Wide (m) – Tele (m)

Projection distance[a]

1.63 – 2.64

2.19 – 3.54

2.76 – 4.44

3.32 – 5.34

5.58 – 8.94

(*3)

4:3 image (*2)

Wide (m) – Tele (m)

2.17 – 3.52

2.93 – 4.72

3.68 – 5.92

4.43 – 7.12

7.43 – 11.92

English

Projection image position

Follow the instructions to adjust the position of the projected image on screen.

This illustration shows the limits within which the zoom function can alter projection distance [a] in relation to screen size. You can adjust the image within these limits so that it fills the screen completely. ( ☞ page 26)

You can adjust the vertical position of the projection image up or down by half of the height of the screen. For example, shifting V.POS fully up brings the lower limit of the image above the centerline of the lens. (☞ page 25)

Wide Tele

Lens centerline

Lens centerline (When shifted fully up)

Lens centerline (When shifted fully down)

If you mount this unit on a tabletop, you can use the adjusters on its underside to change the position of the projection image. Rotate the movable part of the two screw-type adjusters at the front bottom of the case to adjust the height. The movement range of the adjusters is 3 cm (1-1/4 inch). Adjust with care as loosening them further than 3 cm may cause them to separate from the unit.

◆ Keystone adjustment

If you mount the unit at an angle to the screen, it projects trapezoidally distorted images. You can use the [V keystone Correction] or [H keystone Correction] item in the [Setup] menu group to rectify this. (☞ page 36)

Memo

• If the keystone is adjusted aspect ratio may not be correctly maintained. To correctly maintain the aspect ratio, try to use the DPX1300 with the lens shift in the center position.

• The video may be disturbed by keystone correction. Wherever possible, we recommend setting up so the screen and projector form a right angle.

7 Connection

Connecting to AV components

This unit is equipped with 7 types of video input jacks for AV components. Follow the diagram to connect AV components to this unit, taking care to use cables and adapters that match the input jacks.

VIDEO S VIDEO INPUT A INPUT B D4 VIDEO HDMI DVI

Input

Signal type

Composite video S-Video Component video/RGB video Component video/RGB video Component video Component video/RGB video (digital) RGB video (digital)

Pin jack Mini DIN connector BNC connector x 3-5 D-sub 15 pin D connector HDMI connector DVI connector

Connector type

Warning

• Be sure to turn off the power of this unit and the source component before attempting connection.

• Connection methods and jack names may differ depending on the component you are attempting to connect. Refer to the owner’s manual for the component.

• Insert all plugs firmly to avoid noise or other problems.

HDMI cable (digital)

DVI cable (digital)

RGB/YP

INPUT B

DVI

BPR

HDMI

G/Y B/PB/CBR/PR/C

D4 VIDEO

/YCBC

INPUT A

HD/SYNC

OUT IN

REMOTE

RS-232C

S VIDEO VIDEO

TRIGGER OUT

Connection

D-sub monitor cable

BNC cable for component connection

Video pin cable

S-Video cable

Pin/BNC adapters

D connector

Pin cable

cable

HDMI

output

connector

DVI output

connector

D1—4

output

connectors

G/YR

Pin jacksD-sub

BNC jacks S-Video output

PR/

B/PB/

Video output

jack

Component/RGB video output connectors

Image output from AV components

Memo

• Be sure to connect Y/PB/PR and Y/CB/CR to the jacks with the correct signals when connecting AV components to INPUT A. Refer to the owner’s manual of the source component for more information. You may need to make connections to HD/SYNC and VD for RGB video signals.

English

Connecting to computer devices

You can use the following three methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and jacks you wish to use. The HDMI terminal does not support PC signals.

INPUT A INPUT B DVI

Input

INPUT B

RGB/YP

D4 VIDEO

BPR

/YCBC

D-Sub monitor cable

Signal type

RGB (Analog) RGB (Analog) RGB (Digital)

HDMIDVI

G/Y B/PB/CBR/PR/C

Monitor output terminal

INPUT A

Connector type

BNC jack x 5 D-sub 15 pin DVI connector

OUT IN

REMOTE

HD/SYNC

RS-232C

S VIDEO VIDEO

TRIGGER OUT

BNC monitor cable

DVI cable

+ polarity (inside)

- polarity (outside)

(GND)

Computer devices

Information for installers

(for US model only)

Use the supplied trigger-out DC plug to control external components. Be sure to solder the wires from an external component to the plug terminals with the correct polarities, as illustrated at left.

Warning

• Soldering the wires to terminals with incorrect polarity may cause bodily injury or may damage this unit and the external component connected to this unit with this cable.

- polarity

+ polarity

8 Projection

Checking installation and connections

◆ Pre-operation check

Prior to projection, adjust settings to suit the location of the main unit and screen, and the input signal you are using. However, there is usually no need to adjust any settings if you have not changed the installation location or components since the last time you used this unit. Check settings and connections only when the unit does not appear to project images correctly.

Prior to projection, check that the main unit and screen are correctly installed, and that source components are connected correctly.

Is the screen installed correctly? “Setting up the DPX-1300”

☞ page 12

To project images, carry out the following procedure.

Check installation and connections

Main unit

Image source component

PURE DIRECT

REC OUT/ZONE 2

SOURCE/REMOTE

DVDDTV/LD

MD/TAPE

CABLE

DSP

MULTI CH

SPEAKERS

2CH/MULTI CH

A B

INPUT SELECTOR

STANDBY

/ON

SILENT OPTIMIZER

PHONES

PROGRAM

INPUT

INPUT MODE

STRAIGHT

CD-R

SAT

VCR 1

VCR 2

TUNER

EFFECT

PHONO

DVR

VIDEO AUX

MIC

AUDIOLVIDEO

S VIDEO

Is the main unit power turned on?

Are the components connected correctly? “Connecting to AV components”

☞ page 15 - 16

VOLUME

MULTI JOG

BALANCE

TONE

CONTROL

OPTICAL

Is the source component power turned on?

Projection

Select an image for projection and image adjustment

Turn on the projector power.

Begin playback of the source image for adjustment.

Select a projection image. (Select an input signal and projection image aspect.)

Adjust focus and vertical/ horizontal positioning.

Projection preparations complete

For an explanation of detailed settings, see “Menu”. ☞ page 27 - 47

English

+ 49 hidden pages