Yamaha CRW2200EZ, CRW2200EDK QUICK START GUIDE
QUICK START GUIDE
Internal CRW2200EZ,CRW2200EDK & CRW2200SZ Models
Table of Contents
1. INTRODUCTION 2
1.1) Welcome to the Yamaha 3-in-1 CD-RW drives
1.2) About your Yamaha 3-in-1 CD-RW drive
2. REGISTRATION 8
3. SCSI MODEL HARDWARE INSTALLATION 9
3.1) Setup Flowchart for SCSI Models
3.2) Installing the SCSI Converter
3.3) About SCSI Controllers
3.4) SCSI Drive Settings
4. E-IDE MODEL HARDWARE INSTALLATION 15
4.1) Setup Flowchart for E-IDE Models
4.2) About the ATAPI/E-IDE Interface
5. PHYSICAL INSTALLATION OF YOUR NEW CD-RW DRIVE 18
5.1) Operating System Recognizes the 3-in-1 drive.
6. INCLUDED SOFTWARE 28
6.1) Nero - Burning ROM 5.5
6.2) InCD
6.3) Nero Cover Designer
6.4) Nero Wave Editor
6.5) Nero Toolkit
6.6) NeroMIX
6.7) Installation
6.8) Program Start
6.9) Other Software
7. MAKING CDS 30
7.1) Creating a CD
7.2) Creating an Audio CD
7.3) Creating a Data CD
7.4) Creating an Image File
7.5) Loading an Image File
7.6) Copying a CD
7.7) Continuing a Multi-Session CD
7.8) Working with InCD
8. OPERATING YOUR NEW 3-IN-1 DRIVE 37
8.1) Front Panel
8.2) Loading a Disc
8.3) Ejecting a Disc
8.4) Troubleshooting
9. VERIFICATION 40
9.1) Understanding Your New CD-RW drive
9.2) Troubleshooting
10. SPECIFICATIONS 45
11. APPENDIX 47
11.1) Writing Modes
11.2) About the Firmware
1
CRW2200EZ/EDK/SZ
Version 2 (8/2001)
1. INTRODUCTION
1.1) Welcome to Yamaha 3-in-1 CD-RW drive family
Thank you for purchasing a Yamaha 3-in-1 CD-RW drive.
Bringing a new dimension to your PC’s capabilities and performance, Yamaha’s 3-in-1
CD-RW drives are designed for recording, re-writing, and playing CDs. Used primarily for
CD duplication, data storage, back-up, and transferring data, CD-RW drives are quickly
becoming mainstream in today’s computers. No other storage medium is so cost effective.
No other medium can be read by over 300 million computers worldwide. And no other
medium lets you record music and play it back on your home stereo or in your car.
Yamaha makes the CD-ReWritable drives that every other drive is compared to. Yamaha
quality, reliability, features, bundled software, and reputation are the reasons.
Before you can start enjoying all the features and benefits of your new Yamaha 3-in-1
CD-RW drive, please read this manual thoroughly. It is also a good idea to keep this
manual in a safe place for future reference.
1.1.1) List of the Products Supported by This Manual
This manual provides information relevant to the following Yamaha 3-in-1 CD-RW drives:
Model Name Function Feature Summary
CRW2200SZ 20X Write, 10X Re-Write, 40X Read Internal SCSI CD ReWritable drive
CRW2200EZ 20X Write, 10X Re-Write, 40X Read Internal E-IDE CD ReWritable drive
CRW2200EDK
20X Write, 10X Re-Write, 40X Read Internal E-IDE CD ReWritable drive
1.1.2) System Requirements
Your new Yamaha CD-RW drive is a high performance CD recording device. For optimum
performance, Yamaha recommends installing your new CD-RW drive in a high performance PC. While complying to the minimum requirements highlighted below will ensure
proper installation and operation of the drive, Yamaha’s recommended requirements are
essential for high speed (12x and above) recording speeds.
Recommended Requirements:
IBM PC and compatibles:
• Intel Pentium II or equivalent CPU running at 333 MHz or faster
• 32MB memory (64MB or more recommended)
• Fast hard disk drive with 15 ms or faster access speed
• High Performance CD-ROM or DVD-ROM drive for Audio CD duplication and software installation
• An available 5.25" drive bay for mounting the drive
• Available PCI-based SCSI controller card (CRW2200SZ) or available IDE controller port
(CRW2200EZ/EDK)
• Windows 95/98/ME, Windows 2000, or NT 4.0 (with Service Pack 5 or newer)
Important Note: For SCSI models, Yamaha recommends Iwill 2930c / 2930u+ PCI SCSI controllers or Adaptec’s
AHA-29xx, AHA-39xx family of SCSI cards.
2
3
Macintosh and compatibles:
• Mac OS System 8.0 or newer
• Available SCSI controller port (CRW2200SZ) or available IDE controller port
(CRW2200EZ).
1.1.3) Package Contents
If any of the items 1 through 7 (listed below) are missing from the retail package (excludes
refurbished products), please contact Yamaha Customer Support (see section 7.4). In addition to the items listed below, this package may contain additional software (see product
box for details) and optional items such as promotional offers.
1.2) About your new Yamaha 3-in-1 CD-RW Recorder
1.2.1) Major Features of the CRW2200 Series
20X Write Speed: With the industry’s fastest write speed, record a 74-minute CD in less than
4 minutes (fast enough to meet the tightest deadlines)!
10X ReWrite Speed: Record, erase and record again at incredible 10X speed, up to 999 times!
40X Read Speed: With a maximum read speed comparable to top CD-ROM drives, this CD-RW
recorder eliminates the need for an additional CD-ROM drive.
40X Maximum Audio Ripping: Imagine ripping a 3-minute audio track in just under
5 seconds or rip a 74 minute audio CD in less than 3 minutes! With the fastest rip speed
in the industry, up to five times faster than conventional CD-RW or DVD-ROM drives,
this recorder blazes when processing music!
Buffer Memory: All Yamaha CRW2200 Series CD-ReWritable drives offer 8MB of generous
buffer memory, virtually eliminating buffer underruns and preventing wasted time and media.
Safeburn Buffer Management System: SafeBurn is the most comprehensive buffer
management system in the industry, designed not only to eliminate buffer underruns
but also allow you to burn CDs while running multiple applications.
Purephase Laser System: This exclusive Yamaha anti-glare laser technology
compensates for unwanted reflections created on the disc surface during recording,
reducing jitter rates by over 25% for enhanced reliability and improved performance.
Breakthrough Technology: By employing partial CAV (Constant Angular Velocity)
technology, this recorder requires no additional time to control the rotation speed of its
motor, allowing faster, smoother recording.
Waste-Proof Write Strategy : By combining CAV writing support for on-the-fly
data backup specific fine tuning to the included recording software and Yamaha’s
exclusive SafeBurn Buffer Management System, this recorder provides a robust, stable
recording environment that virtually eliminates buffer underruns and wasted media.
RapidLinked™ Packet Writing: Drag and drop files to CD on at a time or all at once.
CD Text Support: Encode music CD album and track titles, arts name and messages directly
onto disc.
Flash-ROM: Instantly upgrade your CD-RW recorder via software to optimize performance and
extends its life.
1. Internal CD-ReWritable drive
2. Quick Start Guide (this booklet)
3. Yamaha/Ahead Installation CD-ROM
4. 3mm mounting screws (total of 4)
5. SCSI Ribbon Cable (CRW2200SZ only)
6. E-IDE Ribbon Cable
(CRW2200EZ/EDK only)
7. Audio Cable (audio output to soundcard input)
8. 1 Blank CD-Recordable (CD-R) media
9. Registration and Warranty Card
10. Late Breaking News
(if applicable)
TM
TM
TM
1.2.2) Main Applications for Yamaha’s 3-in-1 CD-RW Series of Drives:
Music:
Record your own original music on CDs or compile your favorite songs and
create new Audio CDs.
Images & Graphics: Most scanned or digital photos, digital video and computer generated
graphics are notoriously large to record on contemporary, portable media. Now you can record
your images on CDs and free your hard drive space for other uses.
Backup and Archive: Save critical information in the least expensive way. For just
pennies per megabyte, you can copy files to CD-ReWritable media or archive valuable
information for future reference. CDs are recognized as the most reliable, long-lasting medium to
store data. Plus, unlike other media used for backup or archiving, the information stored on a CD is
instantly accessible.
Distribute and Transfer Data: Send multimedia presentations and catalogs with high-
resolution images and CD-quality sound to anyone. With Yamaha CD-ReWritable drives, you do
not have to worry about media compatibility. Any ordinary CD-ROM drive can read the data you
store on a CD-R media using a CD-ReWritable drive.
1.2.3) CD-ReWritable Drives vs. CD-Recordable Drives
All Yamaha CD-RW drives are “multi-function” or “3-in-1” drives. This means that your new drive
may be used as a CD-R drive (to write once on CD-R media), a CD-RW drive
(to rewrite on CD-RW media), or as a CD-ROM drive (to play audio or computer CDs).
1.2.4) How CD-RW Drives Write and Re-Write
To write on CD-R media, CD-RW drives write data by burning tiny pits into a green, gold, or
blue dye layer. The disc is read by a head which is simply looking for the absence or presence
of reflected laser light.
To re-write on CD-RW media, CD-RW drives write data by altering the alignment of crystalline
structures in the media. When the disc is read by a laser, these changes in the crystalline structure alter the phase of the reflected light. The disc can be “wiped clean”
in an erase process that realigns the crystalline elements.
Your new Yamaha 3-in-1 CD-RW drive automatically recognizes and accommodates whatever CD
media is inserted. For better clarification, please study the table below:
4
Format Function
Compatibility?
CD-R
Nearly all CD-ROM drives
Audio CD Players
All but the earliest DVD drives
CD-RW
CD-RW drives
MultiRead(MR) enabled CD-ROM
drives and CD-Players (MR drives/players are a recent development with a limited installed base)
Cost of Media?
Very Low
2X that of CD-R
Erasable?
No - Write Once
Yes - May be re-recorded up to
999 times
Capacity?
650MB data
74 Min. Audio
700MB data
80 Min. Audio
650MB data / 74 Min. Audio
700 MB data / 80 Min. Audio
Storage Life?
75-200 years
30 years
Maximum Recording Speed?
20X
10X
Application?
Archival Storage
Storage requiring “audit trail”
(medical/financial/legal records, etc.)
Audio CD
Distribution of Large
Data Files
Prepare Multimedia
Presentation
Back-up
Supplement to hard drive
Software Authoring
5
CD-R discs
The CRW2200 drives can write to these discs at 1X, 2X, 4X, 8X, 12X, 16X
or 20X speed. These discs can be played back in a CD-ROM drive or a CD
player.
16X-20X speed writing is enabled with Partial CAV method. See
page 6
When writing at 8X or faster speeds, use “high-speed writing
capable” discs.
CD-RW discs
There are two types of CD-RW discs: those that support write/rewrite
speeds of 1X, 2X, and 4X, and those that support only 2X. The
CRW2200 drives can write/rewrite at 2X or 4X speed on the first type of
disc and at 2X on the second type of disc. These discs can be read/
played on a device (e.g., CD-ROM drive) that supports “CD-RW.”
High Speed CD-RW discs
These discs allow writing/rewriting at 4X to 10X speeds. The CRW2200
drives can write/rewrite these discs at 4X, 8X, or 10X speed. These discs
can be read/played by a CD-RW drive that bears the High Speed CD-RW
logo, or by a device (e.g., CD-ROM drive) that supports “CD-RW.”
10X-speed writing is enabled with Full CAV method.
• In order to write, erase, or read these discs using a CD-R/
RW drive, a drive bearing the High Speed CD-RW logo must
be used. When using a CD-ROM drive to read these discs,
the drive must be capable of reading CD-RW discs.
• If these discs are used in a CD-R/RW drive not bearing
the High Speed CD-RW logo, the discs may not be
recognized, resulting in the computer not operating
correctly or other malfunctions occurring.
• Refer to the page at the URL below before attempting to
read these discs on a Yamaha CD-R/RW drive not bearing
the High Speed CD-RW logo.
URL: http://www.yamaha.co.jp/english/product/computer/
1.2.5) About CD-R and CD-RW Discs
6
1.2.6) About Partial CAV (Constant Angular Velocity) Writing Method
Writing to a CD-R disc is normally done using CLV (Constant Linear Velocity) method. In this
method, the disc’s rotation speed is adjusted continuously to keep a steady data transfer rate.
The data transfer rate, in the CLV method, is held constant but, because of the smaller size of the
inner circles of the disc versus the large outer circles, the disc speed is adjusted depending upon
which portion of the disc data is being recorded on (i.e. if recording on the inner edge versus the
outer edge, the disc should rotate faster to keep up with the data transfer rate - which is held
steady throughout the writing cycle.)
In contrast, the CAV (Constant Angular Velocity) method keeps the disc’s rotation speed constant while adjusting the data transfer rate depending upon which portion of the disc is being
recorded. In other words, in the CAV writing method, the outer portion of the disc should
receive an increased data transfer rate compared to the inner portion. Applying the CAV
method enables a significant increase in the data transfer rates with a minimum load increase to
the drive’s mechanism.
Yamaha’s new CRW2200 Lightspeed drives use the CAV method in the inner portions of the
disc while using CLV method in the outer portions of the disc in order to enable up to 20x of
writing speed. This is called a Partial CAV method.The drive will control the disc rotation speed
to start writing at 12X speed in the inner portions, gradually accelerating up to 20X speed and
maintaining 20X speed in the outer portions.
1.2.7) About 10X-speed writing/rewriting of a High Speed CD-RW Disc
10X-speed writing/rewriting of a High Speed CD-RW disc is enabled with the CLV method, and
the 4X-10X Full CAV method. Commonly, writing/rewriting is enabled with the CLV Method.
When writing/rewriting with packet writing, you can also select the Full CAV method.
For more details, refer to the documentation that came with your writing software. (Make sure
that your writing software supports the Full CAV method. The supplied writing software is supported.)
When you try to open and use a file recorded on a CD-RW disc with an application, Yamaha
recommends you using the Full CAV method.
1.2.8) What is “Buffer Underrun”
CD-R/RW drives are equipped with buffer memory. this memory temporarily stores data
while a disc is being recorded. When buffer memory becomes empty (due to unexpected
interruptions or the system’s inability to keep up with the writing process), a write error
occurs. This error is known as a “buffer underrun error”.
Important Note: The Orange Book standard defines how all recordable discs (including CD-R and
CD-RW) are written. Part 2 of the Orange Book standard relates to CD-R discs, and Part 3 to CD-RW
discs. The standard was named after the color of the book’s pages.
2
7
1.2.9) Yamaha Buffer Underrun Protection
Buffer Underrun Protection is featured in Yamaha’s CRW2200 series CD-R/RW drives.
When a buffer underrun is about to occur, a buffer underrun error is prevented by temporarily suspending the writing process. Writing resumes when enough data has accumulated again in buffer memory. Buffer Underrun Protection on the CRW2200 series is
extremely accurate, resulting in seamless recording between stop and continuation points.
Data
Data is stored in
buffer memory...
If data transfer is
interrupted...
when no data is left
in buffer memory...
(Buffer underrun)
and then written
to disc
then buffer memory
begins to empty
Writing fails
(Buffer Underrun
Error)
A Buffer Underrun error will permanently ruin the disc.
➀➁
If data transfer is
interrupted...
writing is suspended
and buffer memory is
about to empty
Once data transfer
resumes normally...
writing continues
enough data has accumulated
in buffer memory...
Yamaha Buffer Underrun Protection ensures error-free results.
➀➁➂
2. REGISTRATION
It is very important that you register your new Yamaha CD-RW drive. Registration entitles
you to receive technical support and customer service, as well as valuable information
regarding upgrades and new product introductions from Yamaha. The unique serial number
of your new Yamaha 3-in-1 drive can be found on the unit, as illustrated below.
Important Note: Please write down the serial number of your 3-in-1 CD-RW drive as illustrated in the picture
above. Make sure this serial number is included with your registration information posted on the web or sent
to us by mail. It is also a good idea to write down the serial number of your 3-in-1 CD-RW drive somewhere
else in order to be able to easily refer to it should it become necessary
You can register your Yamaha CD-RW drive by sending in your user Registration Card
(included in the package) by mail or online by visiting www.yamaha.com.
8
Serial No.
Serial number
(3 letters and 7 digits
write serial
number
here
3. SCSI MODEL HARDWARE INSTALLATION
3.1) Setup Flowchart for CRW2200SZ (SCSI)
This flowchart shows the procedure for setting up your new Yamaha 3-in-1 SCSI drive. For
easy cross-referencing, the relevant pages in this manual are also given.
Do you have a SCSI
adapter card?
STEP
1
Obtain a SCSI adapter card
Recommended models:
See Section 1.1.2 on pages 2 and 3
STEP
1.1
Check that the SCSI adapter
card is correctly installed
Go the Control Panel | System | Manager
tab. Double-click on SCSI controllers
and check that the adapter card has
been correctly installed.
STEP
2
Install the SCSI adapter card
Read this manual and insert the SCSI
card into the appropriate slot on
the computer.
STEP
1.2
NO
YES
Set up the CD-RW drive
1. Set the jumper switches
(Pages 13 and 14)
2. Fit the drive into the computer
(Refer to Chapter 4, pages 18 - 25)
STEP
4
Install the SCSI Converter
Follow the directions on page 10
and 11 to install the SCSI Converter
(attachment) provided in this package.
STEP
3
Check that the CD-RW drive
is correctly installed
Go to Control Panel | System | Device
Manager tab. Double-click on CDROM
and check that the drive has been
correctly installed.
STEP
5
Install the CD writing software
For details about how to install the
software, refer to Chapter 6, starting
on page 28 or read the online manual
that comes on the software disc.
STEP
6
Start using the drive!
Use the drive to create audio CDs, to
back up data on your hard disk, or for
whatever purpose suits your needs.
Read Chapter 8 pages 37 - 40 or refer
to the online manuals supplied on the
software disc.
STEP
7
9
IBM Compatible or
Macintosh Computers
10
3.2) Installing the SCSI Converter (CRW 2200SZ Model Only)
If you would like to install this model in a system with a SCSI interface, you will need to
follow the simple instructions below to install the SCSI converter supplied with your new
recorder, converting the unit into a SCSI model. Removal of the converter will convert the
unit back into an E-IDE (ATAPI) unit. Use the included SCSI converter, screw, and power
cable for the SCSI connection.
Use the included SCSI converter, screw, and power cable for the SCSI
connection.
Note
The included SCSI converte r is for the
other device. YAMAHA and its suppliers do not guarantee operation if it is used with
any other device.
Attach the SCSI converter (included) to the rear of the
1.
CRW2200 drive.
SCSI Converter
CRW2200
drive only. Do not use it with any
The jumper switch for the IDE settings on the rear panel of the CRW2200 drive
can be set to any of MASTER/SLAVE/CSEL. This setting does not affect the
CRW2200 drive operation.
Secure the SCSI converter to the CRW2200 drive with the screw
2.
(included).
Screw
Note
Do not apply excessive force when tightening the screw.
11
3. Connect the forked end of the power cable (included) to the
3.3) About SCSI Controllers
The Yamaha CRW2200SZ package does not include a SCSI host adapter card. A host
adapter card provides the interface between your PC and various peripheral devices. A
wide range of cards are available with various levels of performance, features and price. If
you plan to add peripherals such as scanners or external hard drives, you may want a
more capable host adapter. If, on the other hand, you plan to use the host adapter only to
connect this CD-RW, you may prefer a more economical controller. Yamaha recommends
Iwill 2930c / 2930u+ PCI SCSI controllers or Adaptec’s AHA29xx/AHA39xx families of SCSI
cards.
You can purchase SCSI controller cards from your local computer peripheral retailer or you may
contact Yamaha toll-free at 888-926-2426 to purchase a compatible SCSI controller card.
Once you have selected a SCSI host adapter card, install it in your computer following the
directions provided in the card manufacturer’s operating manual.
drive's and the SCSI converter' s DC INPUT connectors.
Connect the smaller connector to the SCSI converter with the yellow
wire to the left. (See the figure below.)
Yellow wire
Top
Bottom
Smaller
connector
Power cable
Notes
These connectors are D-shaped, so you can only connect the power cables in the
correct orientation. Do not apply excessive force when making this connection.
You risk damaging the converter if you make these connections upside down.
Bigger
connector
Top
Bottom
DC INPUT
connector
12
3.4) CRW2200SZ (SCSI) Drive Settings
Before installing your new CD-RW drive in your computer, you will need to set the
following jumpers:
• SCSI ID settings
• Parity setting
• Terminator setting
• Block size setting
You may set these jumpers by inserting a jumper pin in the jumper switch located on the
rear panel of your CD-RW drive.
Important Note: Use long-nose pliers to remove or insert jumper connectors. In the diagrams in this manual,
solid black fill is used to indicate locations where a jumper is used to short between pins.
3.4.1) Rear Panel of CRW2200SZ (SCSI)
The CRW2200SZ drive’s rear panel features the following:
➃ ➄
➅
➁ ➂➀
1. Jumper Switch
Plug a plastic shunt into this jumper switch to set up SCSI ID, Parity,
Terminator and Block Size. (pgs. 13-14)
2. SCSI INTERFACE connector
Insert the connector of the SCSI ribbon cable here. (pgs. 22-23)
3. DC IN connector (The SCSI convertor’s side)
Insert the smaller connector of the power cable (included). (pg. 11)
4. DIGITAL AUDIO OUT connector
If your sound card has a SPDIF (digital audio) input connector, you can
connect the DIGITAL AUDIO OUT connector of the unit to the SPDIF
connector using a digital audio cable (sold separately).
5. ANALOG AUDIO OUT connector
Connect one end of the 4-pin audio cable to this connector, and the other
end to your computer’s sound card or built-in audio. (pg. 21)
6. DC INPUT connector (The CRW2200 drive’s side)
Insert the bigger connector of the power cable (included). (pg. 24)
3.4.2) Setting the SCSI ID Number of Your New Yamaha CD-RW Drive
The default factory setting for the SCSI ID Number is 3. For most installations, no adjustment of the SCSI ID number is necessary.
The SCSI ID number is used so that the computer will recognize a connected SCSI device.
You can assign 0 through 7 as the SCSI ID number. Usually, “7” is reserved for the SCSI
card ID number, and “0” is reserved for the first SCSI device in the chain.
Use a number between 1 and 6 for your new CD-RW drive below for more information on
setting the SCSI ID number. The factory set ID number is “3”.
Important Note: If you are using other SCSI devices, be sure to use a unique ID number for each device.
SCSI ID Setting:
* Use jumper connectors to short the locations shown in black.
Important Note: If you are using Window 95, 98, or ME and the SCSI ID setting on the rear panel is the same
as the number assigned to another SCSI device, the Plug and Play component of Windows 95, 98 or ME can
automatically assign an unused number to your new CD-RW drive (SCAM protocol level 1- if SCAM is enabled).
Please refer to the SCSI Device Connection Diagram (illustration below) for a practical
example of how SCSI devices may be set to function together.
13
Important Note: Turn off the power before setting the SCSI ID number.
124
SCSI ID 0
124
SCSI ID 4
124
SCSI ID 2
124
SCSI ID 6
124
SCSI ID 3
124
SCSI ID 7
124
SCSI ID 1
124
SCSI ID 5
ID SELECT
Parity ON (default) Parity OFF
PARITY
TERMINATOR
BLOCK SIZE
124
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
124
ID SELECT
Terminator ON (default) Terminator OFF
PARITY
TERMINATOR
BLOCK SIZE
124
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
124
ID SELECT
Block size ON Block size OFF (default)
PARITY
TERMINATOR
BLOCK SIZE
124
ID SELECT
PARITY
TERMINATOR
BLOCK SIZE
124
3.4.3) Parity Setting of your new 3-in-1 CD-RW Recorder
• Parity ON (with a jumper): Parity Check will be performed. Normally, use this setting.
• Parity OFF (without a jumper): Parity Check will not be performed.
* Use jumper connectors to short the locations shown in black.
3.4.4) Terminator Setting of your new 3-in-1 CD-RW Recorder
The terminator setting indicates whether or not your new CD-RW drive is the last
connected SCSI device.
• Terminator ON (with a jumper): Use this setting if your new CD-RW drive is the last
device in the internal SCSI daisy-chain.
• Terminator OFF (without a jumper): Use this setting if devices other than your new CDRW drive are in the internal SCSI daisy-chain and your new drive is not the last device.
* Use jumper connectors to short the locations shown in black.
For example, in the SCSI device Connection diagram on the previous page, device D will
have an ON SCSI terminator while device C will have an OFF SCSI terminator.
3.4.5) Block Size Setting of your new 3-in-1 CD-RW Recorder
• Block size ON (with a jumper): Block Size is set to 512Byte/sector. This function is valid
only for workstations, such as those that run UNIX.
• Block size OFF (without a jumper): Normally, use this setting.
* Use jumper connectors to short the locations shown in black.
14
15
Verify your SCSI Card: Before installing your new CD-RW drive, you need to verify that your
SCSI card is working properly. To verify that your SCSI card is properly installed, in Windows
95/98/ME, click Start, then select Settings and then click on the Control Panel. The Control
Panel will open. Double click on System and the System Properties window will be displayed. Select the Device Manager tab and look for SCSI Controllers. Click on the “+” sign
next to SCSI Controllers. You should see the name of your SCSI Controller card there.
Please note that if there is an exclamation mark on a yellow background, you have a device
conflict. Do not install your new CD-RW drive until you have resolved the conflict.
To resolve the device conflict, please follow the instructions below:
• Check the on line Help menu in the software provided with the SCSI Controller card.
• Check the documentation provided with your SCSI Controller.
• Check Windows Help by clicking the Start button and then select Help. Select Index tab and scroll
to and select the Index topic "devices, troubleshooting". Then click Display and select
Troubleshooting Hardware Conflicts.
• Contact the manufacturer of the SCSI Controller.
Once you have verified that your SCSI controller is correctly installed, proceed with the
installation of your new 3-in-1 CD-RW drive.
4. E-IDE (ATAPI) MODEL HARDWARE INSTALLATION
4.1) Setup Flowchart for CRW2200EZ (E-IDE) and CRW2200EDK (E-IDE)
This flowchart shows the procedure for setting up your new Yamaha 3-in-1 E-IDE drive.
For easy cross-referencing, the relevant pages in this manual are also given.
Set up the CD-RW drive
1. Remove the outer casing of
computer. (page 19)
2. Set the jumper switches (page 17)
3. Fit the drive into the computer
(page 23 [Section B] )
STEP
1
Check that the CD-RW
drive is recognized correctly
Go to Control Panel | System | Device
Manager tab. Double-click on CDROM
and check that the drive has been
recognized correctly by the
computer’s OS.
STEP
2
Install the CD writing software
Follow instructions in Chapter 6,
starting on page 28 or refer to the
documentation that came on the
software disc.
STEP
3
Start using the drive!
Use the drive to create audio CDs, to
back up data on your hard disk, or for
whatever purpose suits your needs.
Read Chapter 8, pages 37 - 46 or refer
to the online manuals supplied on the
software disc.
STEP
4
IBM Compatible or
Macintosh Computers
16
AUDIO OU T
DIGITAL ANALOG
DG
CSEL
SLAVE
MASTER
RGL
+
5V
DC INPUT
G+12
V
1
IDE
INTERFACE
CONNECTOR
CSEL
SLAVE
MASTER
L
G
IO OUT
ANALOG AUDIO
OUT connector
Connect one end
of the 4-pin audio
cable to this and
the other end to
your computer’s
sound card or
built-in audio.
DC INPUT
connector
Insert the power
connector from your
computer’s power
supply in this
socket to feed
power to the drive.
IDE INTERFACE connector
Insert the connector of the IDE cable
here. Make sure you align the red line
of the ribbon cable with pin 1 of the
drive’s connector, marked “IDE
INTERFACE CONNECTOR 1.”
DIGITAL AUDIO OUT connector
If your sound card has a digital audio
input, you can connect this connector
to that digital input using a digital
audio cable (sold separately).
1 MASTER jumper switch
Plug a plastic shunt into this jumper switch if you are
connecting the master CRW2200EZ/EDK using an IDE
cable.
2 SLAVE jumper switch (default setting)
Plug a plastic shunt into this jumper switch if you are
connecting the slave CRW2200EZ
/EDK
using an IDE cable.
3 CSEL jumper switch
If your computer supports the CSEL function, plug a
plastic shunt into this jumper switch to have the
computer automatically select master or slave for the
CRW2200EZ/EDK.
4.2) About the E-IDE (ATAPI) Interface
The most common standard for connecting internal hard drives and CD-ROM drives inside a
PC is the E-IDE (ATAPI) interface.
E-IDE or Enhanced IDE computers normally have two IDE interface connectors; a primary
and a secondary. Each IDE interface connector allows up to two IDE devices to be connected for a total of four IDE devices. Typically, a hard disk is connected to the primary connector while a CD-ROM drive is attached to the secondary connector.
Important Note : Avoid connecting your new CD-RW 3-in-1 drive to the same primary IDE connector as the
one connected to your hard drive if possible. Select the secondary connector that may be connected to your
CD-ROM drive. But, if you must connect it to the primary connector, make sure there is only one device (your
hard drive) selected as MASTER and all other devices are selected as SLAVE.
4.2.1) Rear panel of CRW2200EZ (E-IDE) and CRW2200EDK (E-IDE)
The CRW2200EZ/EDK drive’s rear panel features the following:
Loading...