R
IMPORTANT
Check your power supply
Make sure that your local AC mains voltage matches the voltage specified on the name plate on the bottom panel. In some
areas a voltage selector may be provided on the bottom panel
of the main keyboard unit near the power cord. Make sure that
the voltage selector is set for the voltage in your area. The
voltage selector is set at 240V when the unit is initially
shipped. To change the setting use a “minus” screwdriver to
rotate the selector dial so that the correct voltage appears next
to the pointer on the panel.
SPECIAL MESSAGE SECTION
PRODUCT SAFETY MARKINGS: Yamaha electronic
products may have either labels similar to the graphics
shown below or molded/stamped facsimiles of these
graphics on the enclosure. The explanation of these graphics appears on this page. Please observe all cautions indicated on this page and those indicated in the safety instruction section.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
See bottom of Keyboard enclosure for graphic symbol markings
The exclamation point within the equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
Battery Notice: This product MAY contain a small nonrechargable battery which (if applicable) is soldered in
place. The average life span of this type of battery is approximately five years. When replacement becomes necessary, contact a qualified service representative to perform the replacement.
Warning: Do not attempt to recharge, disassemble, or
incinerate this type of battery. Keep all batteries away
from children. Dispose of used batteries promptly and as
regulated by applicable laws. Note: In some areas, the
servicer is required by law to return the defective parts.
However, you do have the option of having the servicer
dispose of these parts for you.
Disposal Notice: Should this product become damaged
beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and
federal regulations that relate to the disposal of products
that contain lead, batteries, plastics, etc.
NOTICE: Service charges incurred due to lack of knowledge relating to how a function or effect works (when the
unit is operating as designed) are not covered by the
manufacturer’s warranty, and are therefore the owners
responsibility. Please study this manual carefully and consult your dealer before requesting service.
The lightning flash with arrowhead
symbol, within the equilateral triangle,
is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electrical shock.
IMPORTANT NOTICE: All Yamaha electronic products are tested and approved by an independent safety
testing laboratory in order that you may be sure that when
it is properly installed and used in its normal and customary manner, all foreseeable risks have been eliminated.
DO NOT modify this unit or commission others to do so
unless specifically authorized by Yamaha. Product performance and/or safety standards may be diminished.
Claims filed under the expressed warranty may be denied
if the unit is/has been modified. Implied warranties may
also be affected.
SPECIFICATIONS SUBJECT TO CHANGE: The
information contained in this manual is believed to be
correct at the time of printing. However, Yamaha reserves
the right to change or modify any of the specifications
without notice or obligation to update existing units.
NAME PLATE LOCATION: The graphic below indicates the location of the name plate. The model number,
serial number, power requirements, etc., are located on
this plate. You should record the model number, serial
number, and the date of purchase in the spaces provided
below and retain this manual as a permanent record of
your purchase.
CLP-860/860M
CLP-880/880M/880PE
CLP-840
CLP-820
ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and environmentally
friendly. We sincerely believe that our products and the
production methods used to produce them, meet these
goals. In keeping with both the letter and the spirit of the
law, we want you to be aware of the following:
92-469 1
CLP-820S
Model _____________________________________
Serial No. __________________________________
Purchase Date ______________________________
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep these precautions in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock,
short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
• Do not open the instrument or attempt to disassemble the internal parts or
modify them in any way. The instrument contains no user-serviceable parts.
If it should appear to be malfunctioning, discontinue use immediately and
have it inspected by qualified Yamaha service personnel.
• Do not expose the instrument to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might spill
into any openings.
• If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the instrument, or if any unusual smells or
smoke should appear to be caused by it, immediately turn off the power
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the
instrument or other property. These precautions include, but are not limited to, the following:
switch, disconnect the electric plug from the outlet, and have the instrument
inspected by qualified Yamaha service personnel.
• Only use the voltage specified as correct for the instrument. The required
voltage is printed on the name plate of the instrument.
• Before cleaning the instrument, always remove the electric plug from the
outlet. Never insert or remove an electric plug with wet hands.
• Check the electric plug periodically and remove any dirt or dust which may
have accumulated on it.
• Do not place the power cord near heat sources such as heaters or radiators,
and do not excessively bend or otherwise damage the cord, place heavy
objects on it, or place it in a position where anyone could walk on, trip over,
or roll anything over it.
• When removing the electric plug from the instrument or an outlet, always
hold the plug itself and not the cord. Pulling by the cord can damage it.
• Do not connect the instrument to an electrical outlet using a multiple-connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet.
• Remove the electric plug from the outlet when the instrument is not to be
used for extended periods of time, or during electrical storms.
•
Before connecting the instrument to other electronic components, turn off the
power for all components. Before turning the power on or off for all components, set all volume levels to minimum. Also, be sure to set the volumes of
all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level.
• Do not expose the instrument to excessive dust or vibrations, or extreme
cold or heat (such as in direct sunlight, near a heater, or in a car during the
day) to prevent the possibility of panel disfiguration or damage to the internal components.
• Do not use the instrument near other electrical products such as televisions,
radios, or speakers, since this might cause interference which can affect
proper operation of the other products.
• Do not place the instrument in an unstable position where it might accidentally fall over.
• Before moving the instrument, remove all connected cables.
• When cleaning the instrument, use a soft, dry cloth. Do not use paint thinners,
solvents, cleaning fluids, or chemical-impregnated wiping cloths. Also, do
not place vinyl, plastic or rubber objects on the instrument, since this might
discolor the panel or keyboard.
•
On the CLP-880PE, gently remove dust and dirt with a soft cloth. Do not wipe
too hard since small particles of dirt can scratch the instrument’s finish.
• On the CLP-880PE, bumping the surface of the instrument with metal, porcelain, or other hard objects can cause the finish to crack or peel. Use caution.
• Do not rest your weight on, or place heavy objects on the instrument, and do
not use excessive force on the buttons, switches or connectors.
(1)B-6vari.
• (For instruments with a key cover) Take care that the key cover does not
pinch your fingers, and do not insert a finger or hand in the key cover gap.
• (For instruments with a key cover) Never insert or drop paper or metallic or
other objects between the slits of the key cover and the keyboard. If this
happens, immediately turn off the power and remove the electric plug from
the outlet and have the instrument inspected by qualified Yamaha service
personnel.
• Do not place the instrument against a wall (allow at least 3 cm/one-inch
from the wall), since this can cause inadequate air circulation, and possibly result in the instrument overheating.
• Read carefully the attached documentation explaining the assembly process. Failure to assemble the instrument in the proper sequence might
result in damage to the instrument or even injury.
• Do not operate the instrument for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If
you experience any hearing loss or ringing in the ears, consult a physician.
■USING THE BENCH (if included)
• Do not play carelessly with or stand on the bench. Using it as a tool or
step-ladder or for any other purpose might result in accident or injury.
• Only one person should sit on the bench at a time, in order to prevent the
possibility of accident or injury.
• (For height-adjustable benches) Do not attempt to adjust the bench height
while sitting on the bench, since this can cause excessive force to be imposed on the adjustment mechanism, possibly resulting in damage to the
mechanism or even injury.
• If the bench screws become loose due to extensive long-term use, tighten
them periodically using the included tool.
■SAVING USER DATA
• Save all data to an external device such as the Yamaha MIDI Data Filer MDF3,
in order to help prevent the loss of important data due to a malfunction or
user operating error.
Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use.
CLP-880/860/840/820/820S
3
Introduction
Thank you for choosing a Yamaha Clavinova. Your Clavinova is a fine musical instrument that employs
advanced Yamaha music technology. With the proper care, your Clavinova will give you many years of
musical pleasure.
● Stereo sampling of the acoustic piano voices offers unmatched realism and expressive
power, while the AWM (Advanced Wave Memory) tone generator system offers rich,
realistic reproductions of all other voices.
● Piano-like touch response — adjustable in 4 stages — provides extensive expressive
control and outstanding playability.
● Dual mode allows 2 voices to be played simultaneously.
● Split mode (CLP-880/860) allows different voices to be played by the left and right
hands.
● On the CLP-880/860, damper pedal includes natural resonance effect for the piano
voices, simulating the string and sound-board resonance of acoustic pianos.
● Metronome feature with variable tempo facilitates practice.
● 2-track digital recorder lets you record and play back anything you play on the key-
board.
● MIDI compatibility and a range of MIDI functions make the Clavinova useful in a range
of advanced MIDI music systems.
● Built-in computer interface for direct connection to personal computers running advanced music software.
In order to make the most of your Clavinova’s performance potential and features, we urge you to read
this Owner’s Manual thoroughly, and keep it in a safe place for later reference.
* The models CLP-880M, CLP-880PE and CLP-860M will be referred to as the CLP-880 and CLP-860 in this
Owner’s Manual.
Included Accessories
● Owner’s Manual
● Bench (included or optional depending on locale)
CLP-880/860/840/820/820S
4
● Dust Cover (CLP-820S only)
Contents
The Control Panel ..........................................................6
Key Cover & Music Stand .............................................. 8
Connections ................................................................. 10
Selecting & Playing Voices ...........................................11
Playing the Demonstration Tunes ................................ 12
■
V oice Demo..............................................................12
■
Piano Song ..............................................................13
■
Piano Song A-B Repeat ..........................................14
■
Piano Song Part Cancel .........................................15
●
Synchro Start..................................................... 15
●
Left Pedal Start/Stop .........................................15
The Dual Mode ............................................................ 16
●
Other Dual Mode Functions...............................16
The Split Mode (CLP-880/860) ........................................ 17
●
Selecting the Right and Left Voices................... 17
●
Setting the Split Point ........................................17
●
Other Split Mode Functions ...............................17
Reverb ........................................................................ 18
●
Adjusting Reverb Depth.....................................18
The Effect (CLP-880/860/840) .......................................... 19
●
Adjusting Effect Depth ....................................... 19
Brilliance (CLP-880/860/840) ........................................... 19
The Pedals................................................................... 20
●
Damper (Right) Pedal........................................ 20
●
Sostenuto (Center) Pedal (except for CLP-820S) .....20
●
Soft (Left) Pedal.................................................20
Touch Sensitivity ......................................................... 21
Transposition ............................................................... 21
Tuning ......................................................................... 22
●
Tuning Up ..........................................................22
●
Tuning Down......................................................22
●
To Restore Standard Pitch.................................22
The Metronome & Tempo Control ................................ 23
■
The Metronome .......................................................23
●
Metronome Time Signature ...............................23
●
Metronome Volume Function.............................23
■
Tempo Control......................................................... 23
Using the Recorder ...................................................... 24
■
Recording ................................................................24
●
Changing the Initial Settings..............................25
●
Erasing a Single Track....................................... 25
■
Playback ..................................................................26
●
Synchro Start..................................................... 26
●
Left Pedal Start/Stop .........................................26
The Function Mode ...................................................... 27
●
To Select a Function … .....................................27
■
F1: Tuning ................................................................ 28
■
F2: Scale ..................................................................28
F2.1: Scale ...........................................................28
F2.2: Base Note ...................................................28
■
F3: Dual Mode Functions .......................................29
F3.1: Dual Balance...............................................29
F3.2: Dual Detune ................................................ 29
F3.3: 1st Voice Octave Shift.................................29
F3.4: 2nd Voice Octave Shift................................ 29
F3.5: 1st Voice Effect Depth
F3.6: 2nd Voice Effect Depth
F3.5: Reset
F3.7: Reset
■
F4: CLP-880/860 Split Mode Functions.................30
(CLP-820/820S) .....................................30
(CLP-880/860/840) .................................. 30
(CLP-880/860/840) ........30
(CLP-880/860/840).......30
F4.1: Split Point.................................................... 30
F4.2: Split Balance ............................................... 30
F4.3: Right Voice Octave Shift .............................31
F4.4: Left Voice Octave Shift................................ 31
F4.5: Right Voice Effect Depth .............................31
F4.6: Left Voice Effect Depth ...............................31
F4.7: Damper Range............................................31
F4.8: Reset...........................................................31
■
F4: CLP-840/820/820S Left Pedal Mode ................32
■
F5: CLP-880/860 Pedal Functions .........................32
F5.1: Left Pedal Mode.......................................... 32
F5.2: Damper Mode .............................................32
F5.3: Soundboard Depth...................................... 32
■
F5: CLP-840/820/820S Metronome Volume...........33
■
F6: CLP-880/860 Metronome Volume ....................33
■
F6:
CLP-840/820/820S Piano Song Part Cancel Volume
■
F7:
CLP-880/860 Piano Song Part Cancel Volume
■
F7: CLP-840/820/820S MIDI Functions ..................34
■
F8: CLP-880/860 MIDI Functions ...........................34
●
A Brief Introduction to MIDI................................ 34
..33
.......33
F7.1/F8.1: MIDI Transmit Channel Selection .......34
F7.2/F8.2: MIDI Receive Channel Selection ........ 34
F7.3/F8.3: Local Control ON/OFF ........................ 35
F7.4/F8.4: Program Change ON/OFF.................. 35
F7.5/F8.5: Control Change ON/OFF .................... 36
F7.6/F8.6: MIDI Transmit Transpose ....................36
F7.7/F8.7: Panel/Status Transmit......................... 36
F7.8/F8.8: Bulk Data Dump..................................36
■
F8: CLP-840/820/820S Backup Functions.............37
■
F9: CLP-880/860 Backup Functions ......................37
F8.1/F9.1: Voice ................................................... 37
F8.2/F9.2: MIDI ....................................................37
F8.3/F9.3: Tuning ................................................. 37
F8.4/F9.4: Pedal...................................................37
Connecting to a Personal Computer ............................. 38
●
Connecting to an Apple Macintosh Series Computer
●
Connecting to an IBM-PC/AT Series Computer
....38
........39
Factory Preset Recall .................................................. 40
Troubleshooting ........................................................... 40
Options & Expander Modules ...................................... 40
Demo Song List..................................................................41
Factory Setting List............................................................42
MIDI Data Format................................................................43
MIDI Implementation Chart................................................47
CLP-880: Keyboard Stand Assembly ...............................48
CLP-860/840/820: Keyboard Stand Assembly .................56
CLP-820S: Keyboard Stand Assembly ............................. 62
Specifications.....................................................................68
CLP-880/860/840/820/820S
5
The Control Panel
CLP-820/820S
MASTER VOLUME
MAX
MIN
2
CLP-840
MASTER
VOLUME
BRILLIANCE
MAX
BRIGHT
MIN
MELLOW
23
CLP-860
MASTER
VOLUME
BRILLIANCE
MAX
BRIGHT
MIN
MELLOW
23
CLP-880
MASTER
VOLUME
BRILLIANCE
MAX
BRIGHT
MIN
MELLOW
23
4
5
4
5
4
5
4
5
DEMO
TRANSPOSE
DEMO
TRANSPOSE
DEMO
TRANSPOSE
DEMO
TRANSPOSE
ROOM
HALL 1
HARD
HALL 2
MEDIUM
STAGE
REVERB
TOUCH
SOFT
GRAND
PIANO
E. PIANO
HARPSICHORD
STRINGS
ORGAN
PIPE
VARIATION
68 9
ROOM
CHORUS
HALL 1
HALL 2
STAGE
REVERB
SYMPHONIC
TREMOLO
DELAY
EFFECT
TOUCH
HARD
MEDIUM
SOFT
GRAND
STRINGS
ORGAN
PIPE
VARIATION
CLASSICAL
E. PIANO 1
PIANO
PIANO
E. PIANO 2
HARPSICHORD
678 9
CLASSICAL
GRAND
JAZZ
ROCK
PIANO
ROOM
HALL 1
HALL 2
STAGE
REVERB
CHORUS
SYMPHONIC
TREMOLO
DELAY
EFFECT
TOUCH
HARD
MEDIUM
SOFT
PIANO
E. PIANO 2
PIANO
HARPSICHORD
PIANO
STRINGS
ORGAN
E. PIANO 1
PIPE
BASS
VARIATION SPLIT
678 9 0
ROOM
HALL 1
HALL 2
STAGE
REVERB
CHORUS
SYMPHONIC
TREMOLO
DELAY
EFFECT
TOUCH
HARD
MEDIUM
SOFT
GRAND
PIANO
HARPSICHORD
CLASSICAL
STRINGS
ROCK
JAZZ
PIANO
ORGAN
E. PIANO 1 E. PIANO 2
PIANO
CHURCH
JAZZ
PIPE
ORGAN
ORGAN
BASS
VARIATION SPLIT
PIANO
678 9 0
!# $
METRO-
NOME
TEMPO
FUNCTION
FUNCTION
PIANO
SONG
–
/
NO + / YES
@
!# $
METRO-
NOME
TEMPO
FUNCTION
FUNCTION
PIANO
SONG
–
/
NO + / YES
@
!# $
METRO-
NOME
TEMPO
FUNCTION
FUNCTION
PIANO
SONG
–
/
NO + / YES
@
!# $
METRO-
NOME
TEMPO
FUNCTION
FUNCTION
PIANO
SONG
–
/
NO + / YES
@
&
RECORDER
1
2
SONG
START
/
SELECT
REC
STOP
%^
&
RECORDER
1
2
SONG
START
/
SELECT
REC
STOP
%^
&
RECORDER
1
2
SONG
START
/
SELECT
REC
STOP
%^
&
RECORDER
1
2
SONG
START
/
SELECT
REC
STOP
%^
MASTER
VOLUME
BRILLIANCE
DEMO
MAX
BRIGHT
MIN
MELLOW
C1 D1 E1 F1 G1 A1 B1 C2 D2 E2 F2 G2 A2 B2 C3 D3 E3 F3 G3 A3 B3 C4 D4 E4 F4 G4 A4 B4 C5 D5 E5 F5 G5 A5 B5 C6
B0A0G0F0E0D0C0B-1A-1
ROOM
HALL 1
HALL 2
STAGE
REVERB
TRANSPOSE
Tuning keys (See page 22)
PHONES Jacks (Bottom panel) (See page 10)
1 [POWER] Switch
Press the [POWER] switch once to turn the
power ON, a second time to turn the power OFF.
When the power is initially turned ON, a voice
selector LED will light, and the power indicator
located below the left end of the keyboard will light
(except for CLP-820S).
2 [MASTER VOLUME] Control
The [MASTER VOLUME] control adjusts the
volume (level) of sound produced by the Clavinova’s
internal stereo sound system. The [MASTER
VOLUME] control also adjusts headphone volume
1
CLASSICAL
ROCK
JAZZ
GRAND
PIANO
PIANO
PIANO
E. PIANO 1 E. PIANO 2
PIANO
CHORUS
HARD
SYMPHONIC
MEDIUM
TREMOLO
SOFT
DELAY
EFFECT
PIPE
CHURCH
JAZZ
HARPSI-
ORGAN
ORGAN
ORGAN BASS
CHORD
STRINGS
TOUCH
VARIATION SPLIT
METRONOME
RECORDER
PIANO
2
1
SONG
FUNCTION
SONG
START
/
TEMPO
FUNCTION
REC
SELECT
STOP
–
/ NO+ / YES
STEREO SAMPLING
CLP-
880
POWER
D6 E6 F6 G6 A6 B6 C7
CLP-880
when a pair of headphones is plugged into the
PHONES jack (page 10).
3 [BRILLIANCE] Control (CLP-880/860/840)
The [BRILLIANCE] Control adjusts the tonality
or “timbre” of the output sound from a mellow tone
to a bright tone.
4 [DEMO] Button
Activates the demo playback mode in which you
can select playback of different demonstration
sequences for each of the Clavinova’s voices. See
page 12 for details.
CLP-880/860/840/820/820S
6
The Control Panel
5 [TRANSPOSE] Button
The [TRANSPOSE] button allows access to the
Clavinova’s TRANSPOSE function (to shift the
pitch of the entire keyboard up or down in semitone
intervals).
6 [REVERB] Button
The [REVERB] button selects a number of
digital reverb effects that you can use for extra depth
and expressive power. See page 18 for details.
7 [EFFECT] Button (CLP-880/860/840)
This button selects a number of effects which can
give your sound greater depth and animation.
8 [TOUCH] Button
The [TOUCH] button makes it easy to adjust the
touch response of the Clavinova to match your
playing style. See page 21 for details.
9 Voice Selectors & [VARIATION] Button
Simply press any of the voice selectors to select
the corresponding voice. The voice selector LED
will light to indicate which voice is currently selected. Press the [VARIATION] button so that its
indicator lights to select a variation of the currently
selected voice.
There is also a dual mode in which two voices
can be played simultaneously across the full range of
the keyboard (see page 16 for details), and a split
mode on the CLP-880/860 which allows different
voices to be played by the left and right hands (see
page 17 for details).
0 [SPLIT] Button (CLP-880/860)
Engages the split mode, in which different voices
can be played on the left- and right-hand sections of
the keyboard. See page 17 for details.
! [METRONOME] Button
Turns the metronome sound on and off. The
[TEMPO ▼/▲] buttons, below, are used to set the
tempo of the metronome sound. The [–/NO] and [+/
YES] buttons are used to change the time signature
(beat) of the metronome if used while the [METRO-
NOME] button is held — page 23.
corder function. The tempo range is from 32 to 280
beats per minute — page 23. These same buttons are
also used to select functions — page 27.
# [FUNCTION] Button
This button accesses a range of utility functions
— including the MIDI functions — that significantly
enhance versatility and playability. See page 27 for
details.
$ [PIANO SONG] Button
This button enters the Piano Song Mode. While
in this mode you can use the [SONG SELECT ▼/
▲] buttons to select from 50 songs.
% [SONG SELECT ▼/▲] (–/NO, +/YES) Buttons
These buttons select a piano song number for
playback, and are also used to adjust a range of other
parameters (i.e. their “–/NO” and “+/YES” functions).
^ RECORDER [START/STOP] and [REC] But-
tons
These buttons control the Clavinova’s recorder,
letting you record and play back just about anything
you play on the keyboard.
& RECORDER [1] and [2] Buttons
The Clavinova has a 2-track recorder, and these
buttons are used to select the track(s) to be recorded
or played back. See page 24 for details.
* Pedals
The soft (left), sostenuto (center) and damper
(right) pedals (soft/sostenuto [left] and damper
[right] in the case of the CLP-820S) provide a range
of expressive control capabilities similar to the pedal
functions on an acoustic piano. See page 20 for
details.
CLP-880/860/840/820 CLP-820S
*
*
@ [TEMPO ▼/▲] (FUNCTION </>) Buttons
These buttons adjust the tempo of the metronome
function as well as the playback tempo of the re-
Soft pedal
Sostenuto pedal
Damper pedal
Damper pedal
Soft/Sostenuto pedal
CLP-880/860/840/820/820S
7
Key Cover & Music Stand
Be careful to avoid catching your
fingers when opening or closing
the cover.
Key Cover (except for CLP-820S)
■ CLP-880 .........................................................................
To open the key cover:
Gently lift the cover until it is fully open.
To close the key cover:
Gently lower the cover over the keys.
Be careful to avoid catching your
fingers when opening or closing
the cover.
• Hold the cover with both hands when moving it, and do not release it until it is fully opened or
closed. Be careful to avoid catching fingers (yours or others) between the cover and main unit.
• Do not place objects on top of the key cover. Small objects placed on the key cover may fall inside
the main unit when the cover is opened and may not be able to be removed. This could cause
electric shock, short circuit, fire or other serious damage to the instrument.
■ CLP-860/840/820 ...........................................................
To open the key cover:
ZLift the cover slightly (not too much).
XSlide the cover open.
To close the key cover:
ZSlide the cover toward you.
XGently lower the cover over the keys.
CLP-880/860/840/820/820S
8
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Key Cover & Music Stand
Music Stand
To raise the music stand:
ZPull the stand up and toward yourself as far as it will go.
XFlip down the two metal supports at the left and the right on the rear
of the music stand.
CLower the music stand so that it rests on the metal supports.
As shown in the illustration, the angle of the music stand can be set in one
of three positions, according to the position of the metal supports. Set the left
and right metal supports to the same position.
To lower the music stand:
ZPull the music stand toward yourself as far as it will go.
XRaise the two metal supports (at the rear of the stand).
CGently lower the music stand backward until it is all the way down.
• Do not try to use the music stand in a half-raised position.
When lowering the stand, do not release your hands from the music stand
until it is all the way down.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
9
Connections
AUX IN
RL/L+R
12 3 4 5
AUX OUT
RL/L+R
PEDAL
MIDI
IN OUT THRU
HOST SELECT TO HOST
PC-2 PC-1
MIDI
Mac
DOU-10
AUX OUT
RL/L+R
Stereo System
AUX IN
RL/L+R
1 AUX IN L/L+R and R Jacks
These jacks are intended for use with an external tone generator module
such as the Yamaha DOU-10 Disk Orchestra Unit. The stereo outputs from
the external tone generator module are connected to the AUX IN L/L+R
and R jacks, allowing the sound of the tone generator to be reproduced via
the Clavinova’s internal sound system and speakers. A line-level mono
source can be connected to the L/L+R jack.
• The input signal from the AUX IN jacks is controlled by the Clavinova’s volume
and brilliance (CLP-880/860/840) controls. Reverb and effect (CLP-880/860/
840) functions will have no affect.
• The input signal from the AUX IN jacks is delivered to the AUX OUT jacks.
2 AUX OUT L/L+R and R Jacks
The AUX OUT L/L+R and R jacks deliver the output of the Clavino va for
connection to an instrument amplifier, mixing console, PA system, or recording
equipment. If you will be connecting the Clavinova to a monaural sound
system, use only the L/L+R jack. When a plug is inserted into the L/L+R jack
only , the left- and right-channel signals are combined and delivered via the L/
L+R jack so you don’t lose any of the Clavinova’s sound.
• The AUX OUT jack signal must never be returned to the AUX IN jacks, either
directly or through external equipment.
• The AUX OUT jack signal is not controlled by the Clavinova’s volume control.
Use the volume control on the external audio equipment to adjust the level.
MIDI
IN OUT THRU
Tone Generator
DOU-10
HOST SELECT TO HOST
PC-2 PC-1
MIDI
Mac
Personal Computer
3 PEDAL Jack
This terminal is for connecting the pedal cord from the pedal box (refer
to the “Keyboard Stand Assembly” on pages 48-67).
4 MIDI IN, THRU and OUT Connectors
The MIDI IN connector receives MIDI data from an external MIDI
device (such as the DOU-10 Disk Orchestra Unit) which can be used to
control the Clavinova. The MIDI THRU connector re-transmits any data
received at the MIDI IN connector, allowing “chaining” of several MIDI
instruments or other devices. The MIDI OUT connector transmits MIDI
data generated by the Clavinova (e.g. note and velocity data produced by
playing the Clavinova keyboard).
More details on MIDI are given in “MIDI Functions” on page 34.
5 TO HOST Connector & HOST SELECT Switch
This jack and selector switch allow direct connection to a personal
computer for sequencing and other music applications — without the need
for a separate MIDI interface. See page 38 for details.
● PHONES Jacks
(Bottom Panel)
Two sets of standard stereo headphones can be plugged in here for
private practice or late-night playing. The internal speaker system is automatically shut off when a pair of headphones is plugged into either of the
PHONES jacks.
CLP-880/860/840/820/820S
10
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Selecting & Playing Voices
Turn Power On..................................................................................................
After making sure that the Clavinova’s AC cord is properly plugged
POWER
into the Clavinova itself and plugged into a convenient AC wall outlet,
press the [POWER] switch located to the right of the keyboard to turn
the power ON. In some areas a plug adaptor may be provided to match
the pin configuration of the AC wall outlets in your area.
When the power is turned ON, one of the voice selector LEDs will
light, and the power indicator located below the left end of the keyboard will light (except for CLP-820S).
CLP-880
GRAND
PIANO
HARPSI-
CHORD
CLASSICAL
PIANO
STRINGS
MASTER
VOLUME
JAZZ
PIANO
PIPE
ORGAN
MAX
MIN
ROCK
PIANO
CHURCH
ORGAN
E. PIANO 1 E. PIANO 2
JAZZ
ORGAN
BASS
Set the Volume..................................................................................................
Initially set the [MASTER VOLUME] control about half way
between the “MIN” and “MAX” settings. Then, when you start playing,
re-adjust the [MASTER VOLUME] control for the most comfortable
listening level.
Select a Voice.....................................................................................................
Select the desired voice by pressing one of the voice selectors. Use
the [VARIATION] button to select a variation of the current voice, as
required.
VARIATION
Play................................................................................................................................
The Clavinova also offers keyboard touch response, so the volume
and timbre of notes played can be controlled according to how “hard”
you play the keys. The amount of varia tion available depends on the
selected voice.
BRILLIANCE
BRIGHT
MELLOW
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
ROOM
HALL 1
HALL 2
STAGE
REVERB
CHORUS
SYMPHONIC
TREMOLO
DELAY
EFFECT
Add Effects As Required.......................................................................
You can add or change reverb, effects (CLP-880/860/840) and
brilliance (CLP-880/860/840) as desired by using the [REVERB]
button (page 18), [EFFECT] button (page 19) and the [BRIL-
LIANCE] control (page 19).
CLP-880/860/840/820/820S
11
Playing the Demonstration Tunes
Demonstration tunes are provided that effectively demonstrate each of the
Clavinova’s voices. There are also 50 piano songs that you can play individually,
all in sequence, or in random order. Here’s how you can select and play the
demo tunes.
NOTE
• The demo or piano song mode cannot be engaged while the recorder (page 24) is in use.
• No MIDI reception occurs in the demo/piano song mode.
• The demo/piano song data is not transmitted via the MIDI connectors.
* See page 41 for a complete listing of the demo tunes.
Voice Demo
CLP-880
GRAND
PIANO
HARPSI-
CHORD
CLASSICAL
PIANO
STRINGS
JAZZ
PIANO
PIPE
ORGAN
DEMO
DEMO
ROCK
PIANO
CHURCH
ORGAN
E. PIANO 1 E. PIANO 2
JAZZ
ORGAN
BASS
Engage the Demo Mode .........................................................................
Press the [DEMO] button to engage the demo mode — the voice
selector indicators will flash in sequence.
Play a Voice Demo.........................................................................................
Press one of the voice selectors to start playback of all songs starting
from the corresponding voice demo tune — featuring the voice normally selected by that voice selector button. (If you press the [START/
STOP] button instead of a voice selector button, the GRAND PIANO
demo tune will begin playback.) The indicator of the selected voice
selector button will flash during playback, and “- - -” will appear on the
LED display. You can start playback of any other voice demo tune
during playback by simply pressing the corresponding voice selector.
You can stop playback at any time by pressing the [START/STOP]
button or the voice selector of the currently playing demo.
NOTE
• Use the [MASTER VOLUME] control to adjust the volume and the
[BRILLIANCE] control (CLP-880/860/840) to adjust the brilliance (page
19).
Exit From the Demo Mode....................................................................
Press the [DEMO] button to exit from the demo mode and return to
the normal play mode.
CLP-880/860/840/820/820S
12
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
PIANO SONG
Playing the Demonstration Tunes
Piano Song
Engage the Piano Song Mode .........................................................
Press the [PIANO SONG] button to engage the piano song mode —
the [PIANO SONG], [1] and [2] indicators will light.
Play a Piano Song.........................................................................................
START
STOP
SONG
SELECT
–
/ NO+ / YES
/
To play any of the 50 piano songs provided, use the [SONG SE-
LECT ▼/▲] buttons to select the number of the tune you want to play
(the number will appear on the LED display), then press the [START/
STOP] button. Playback will stop automatically when playback of the
selected piano song has finished.
Select “ALL” instead of a number to play all piano songs in se-
quence, or select “rnd” to continuously play all piano songs in random order. Press the [START/STOP] button to stop playback.
• Use the [MASTER VOLUME] control to adjust the volume.
• You can use the [TEMPO ▼/▲] buttons to adjust the playback tempo as
required. This produces a relative tempo variation, with a range from “50” through “- - -” to “50” at maximum; the range will differ depending on
the selected song.
• The default tempo “- - -” is automatically selected whenever a new piano
song is selected, or playback of a new piano song begins during “
“
rnd
” playback.
• You can play the keyboard along with the piano song playback. The voice
playing on the keyboard can be changed.
• You can change the Brilliance control (CLP-880/860/840) and Reverb
type that is applied to the voice you play on the keyboard and for the
piano song playback. You can change the Effect type (CLP-880/860/840)
and Touch sensitivity that is applied to the voice you play on the keyboard. When a new piano song is selected or a new piano song is
automatically started in continuous play, the HALL 1 reverb type will
automatically be selected.
ALL
” or
PIANO
SONG
Exit From the Piano Song Mode....................................................
Press the [PIANO SONG] button to exit from the piano song mode,
the indicator will go off, and return to the normal play mode.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
13
Playing the Demonstration Tunes
Piano Song A-B Repeat
specified phrase within a piano song. Combined with the Part Cancel
function described below, this provides an excellent way to practice
difficult phrases.
Specify the Beginning (A) of the Phrase..............................
The A-B Repeat function can be used to continuously repeat a
RECORDER
12
START
/
REC
STOP
FUNCTION
FUNCTION
Select and play a piano song, then press the [FUNCTION] button at
the beginning of the phrase you want to repeat. This sets the “A” point
(“A-” will appear on the display).
To set the “A” point at the very beginning of the song, press the
[FUNCTION] button before starting playback.
Specify the End (B) of the Phrase ...............................................
Press the [FUNCTION] button a second time at the end of the
phrase. This sets the “B” point (“A-b” will appear on the display). At
this point repeat playback will begin between the specified A and B
points.
Stop Playback....................................................................................................
Press the [START/STOP] button to stop playback while retaining
the specified A and B points. A-B repeat playback will resume if the
[START/STOP] button is then pressed again.
To cancel the A and B points press the [FUNCTION] button once.
NOTE
• The A and B points are automatically canceled when a new song is
selected.
• The A-B Repeat function cannot be used during “
back.
ALL
” or “
rnd
” play-
CLP-880/860/840/820/820S
14
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Playing the Demonstration Tunes
Piano Song Part Cancel
The 50 piano songs have separate left- and right-hand parts that can
be turned on and off as required so you can practice the corresponding
part on the keyboard. The right-hand part is played by the recorder’s [1]
track, and the left-hand part is played by recorder’s [2] track. (Some of
the songs are arrangements for four-hands, tracks [1] and [2] correspond to primo and secondo parts of the arrangement.)
RECORDER
12
START
/
REC
STOP
RECORDER
12
START
/
REC
STOP
RECORDER
12
START
/
REC
STOP
Turn the Desired Part Off ......................................................................
Press the RECORDER [1] or [2] button to turn the corresponding
part off — the corresponding indicator will go out (these buttons
alternately toggle the corresponding part on and off).
NOTE
• The parts can be turned on or off even during playback.
• The Piano Song Part Cancel function cannot be used during “
“
rnd
” playback.
• The “Piano Song Part Cancel Volume” function described on page 33 can
be used to set the canceled part so that it plays at a volume from “0” (no
sound) to “20”. The default setting is “5”.
• Both parts are automatically turned ON whenever a new song is selected.
ALL
” or
Start/Stop Playback.....................................................................................
Press the [START/STOP] button to start and stop playback as
required.
Synchro Start .....................................................................................................
When the Synchro Start function is engaged, playback of the selected piano song will begin automatically as soon as you start playing
on the keyboard.
To engage the Synchro Start function press the [START/STOP]
button while holding the part button corresponding to the part which is
ON. A dot will appear in the lower right corner of the display. (Repeat
the previous operation to disengage the Syncro Start function.)
Playback will then start as soon as you begin playing on the keyboard.
NOTE
• If you hold a track button which is OFF while pressing the [START/STOP]
button, that track will be turned ON and the Synchro Start mode will be
engaged.
Left Pedal Start/Stop..................................................................................
The left pedal can be assigned to start and stop piano song playback
via the “Left Pedal Mode” function described on page 32.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
15
The Dual Mode
I
N
The dual mode makes it possible to play two voices simultaneously across
the entire range of the keyboard.
AZZ
ROCK
PIANO
E. PIANO 1 E. PIA
ANO
Voice numbering priority
1 2 3 4 5 6
CLASSICAL
GRAND
PIANO
PIANO
HARPSICHORD
STRINGS
7 8 9 10 11 12
JAZZ
PIANO
PIPE
ORGAN
ROCK
PIANO
CHURCH
ORGAN
E. PIANO 1 E. PIANO 2
JAZZ
BASS
ORGAN
To activate the dual mode simply press two voice selectors at the
same time (or press one voice selector while holding another). The
voice indicators of both selected voices will light when the dual mode
is active. To return to the normal single-voice play mode, press any
single voice selector.
According to the voice numbering priority as shown in the diagram
on the left, lower valued voice numbers will be designated as the 1st
Voice (the other voice will be designated as the 2nd Voice).
The [STRINGS] [VARIATION] voice has a slow attack. This
voice can sometimes be used with another voice in the Dual Mode to
produce a better “blend”.
NOTE
• The dual and split modes (CLP-880/860) cannot be engaged at the same
time.
• The [VARIATION] button indicator will light if the variation is engaged for
either or both of the dual-mode voices. While the dual mode is engaged
the [VARIATION] button can be used to tur n the variation for both voices
on or off. To use the variation for only one of the voices the setting must
be made prior to engaging the dual mode.
• [EFFECT] in the Dual Mode
Depending upon the conditions one effect type will take priority over the
other. Depth will be decided according to the depth default value of the
voice combination. However, using function F3 (see page 29) you can
change the depth value for each voice as you like.
Effect depth setting via the panel controls (i.e. pressing the [-/NO] or [+/
YES] buttons while holding the [EFFECT] button — see page 19) will be
applied to the 1st Voice only.
• [REVERB] in the Dual Mode
The reverb type assigned to the 1st Voice will take priority over the other.
(If the reverb is set to OFF, the 2nd Voice’s reverb type will be in affect.)
Reverb depth setting via the panel controls (i.e. pressing the [-/NO] or [+/
YES] buttons while holding the [REVERB] button — see page 18) will be
applied to the 1st Voice only.
Other Dual Mode Functions...............................................................
The Clavinova Function mode provides access to a number of other
dual-mode functions, listed below. See the corresponding pages for
details.
• Dual Balance ................................................. 29
• Dual Detune .................................................. 29
• 1st Voice Octave Shift ................................... 29
• 2nd Voice Octave Shift.................................. 29
• 1st Voice Effect Depth ................................... 30
• 2nd Voice Effect Depth.................................. 30
• Reset ............................................................. 30
CLP-880/860/840/820/820S
16
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
SPLIT
The Split Mode (CLP-880/860)
The split mode makes it possible to play two different voices on the keyboard
— one with the left hand and another with the right hand. The Left Voice is
played on all keys to the left of (and including) a specified “split point” key, while
the Right Voice is played on all keys to the right of the split point key.
To activate the split mode simply press the [SPLIT] button so thats
SPLIT
ZZNOROCK
PIANO
E. PIA
indicator lights. The split mode can be turned off at any time by pressing the
[SPLIT] button again so that its indicator goes out.
NOTE
• The dual and split modes cannot be engaged at the same time.
Selecting the Right and Left Voices ....................................................
The voice that was selected before the split mode was engaged becomes
the Right Voice in the split mode. (The Right Voice can also be changed while
in the split mode, by simply pressing the corresponding voice selector.)
To select a Left Voice press the corresponding voice selector while
holding the [SPLIT] button (default: [BASS]). The indicator of the Left
Voice selector will light while the [SPLIT] button is pressed, then only the
Right Voice selector and [SPLIT] button indicators will remain lit.
SPLIT
Example:
• The variation can be individually turned on and off for the split mode voices.
NOTE
Normally the voice indicator of the Right Voice lights in the split mode. The
[VARIATION] can be used to turn the variation for the Right Voice on or off as
required. While the [SPLIT] button is held, however, the voice indicator of the
Left Voice lights, and in this state the [VARIATION] button can be used to turn
the variation for the Left Voice on or off as required.
• [EFFECT] in the Split Mode
Depending upon the conditions, one effect type will take priority over the other.
Depth will be decided according to the depth default value of the voice
combination. However, using function F4 (see page 30) you can change the
depth value for each voice as you like.
Effect depth setting via the panel controls (i.e. pressing the [-/NO] or [+/YES]
buttons while holding the [EFFECT] button — see page 19) will be applied to
the Right Voice only.
• [REVERB] in the Split Mode
The reverb type assigned to the Right Voice will take priority over the other. (If
the reverb is set to OFF, the Left Voice’s reverb type will be in affect.)
Reverb depth setting via the panel controls (i.e. pressing the [-/NO] or [+/YES]
buttons while holding the [REVERB] button — see page 18) will be applied to
the Right Voice only.
Setting the Split Point.........................................................................................
The split point is initially set at the F#2 key by default. You can change
the split point to any other key by pressing the key while holding the
[SPLIT] button (the name of the current split-point key appears on the LED
display while the [SPLIT] button is held). The split point can also be set via
the Function mode (see below).
A-1 b=1 C 2 F~2
A-1 Bb-1 C2 F#2
•“b” is indicated with a lower “_”.
•“#” is indicated with an upper “~”.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Other Split Mode Functions.........................................................................
The Clavinova Function mode provides access to a number of other
split-mode functions, listed below. See the corresponding pages for details.
• Split Point ...................................................... 30
• Split Balance ................................................. 30
• Right Voice Octave Shift ............................... 31
• Left Voice Octave Shift.................................. 31
• Right Voice Effect Depth ............................... 31
• Left Voice Effect Depth.................................. 31
• Damper Range .............................................. 31
• Reset............................................................. 31
CLP-880/860/840/820/820S
17
Reverb
The [REVERB] button selects a number of digital reverb effects that you can
use for extra depth and expressive power.
ROOM
HALL 1
HALL 2
STAGE
REVERB
To select a reverb type press the [REVERB] button a few times
until the indicator corresponding to the desired type lights (the indicators light in sequence each time the [REVERB] button is pressed). No
reverb is produced when all indicators are off.
OFF
No reverb effect is selected when no REVERB indicator is lit.
ROOM
This setting add a continuous reverb effect to the sound that is similar
to the type of acoustic reverberation you would hear in a room.
HALL 1
For a “bigger” reverb sound, use the HALL 1 setting. This effect
simulates the natural reverberation of a small-size concert hall.
HALL 2
For a really spacious reverb sound, use the HALL 2 setting. This effect
simulates the natural reverberation of a large concert hall.
STAGE
A simulation of the type of reverb produced in a stage environment.
NOTE
• The default reverb type (including OFF) and depth settings are different
for each voice.
ROOM
HALL 1
HALL 2
STAGE
REVERB
SONG
SELECT
–
/ NO+ / YES
Adjusting Reverb Depth.........................................................................
Adjust the reverb depth for the selected voice by using the [–/NO]
and [+/YES] buttons while holding the [REVERB] button. The depth
range is from 0 through 20 (the current depth setting appears on the
LED display while the [REVERB] button is held). A setting of “0”
produces no effect, while a setting of “20” produces maximum reverb
depth. Press the [–/NO] and [+/YES] buttons simultaneously while
holding the [REVERB] button to recall the default setting for the
current voice (default depth settings are different for each voice).
CLP-880/860/840/820/820S
18
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Effect (CLP-880/860/840)
The [EFFECT] button allows you to select one of the effects that can give
your sound greater depth and animation.
CHORUS
SYMPHONIC
TREMOLO
DELAY
EFFECT
To select an effect type press the [EFFECT] button a few times
until the indicator corresponding to the desired type lights (the indicators light in sequence each time the [EFFECT] button is pressed). No
effect is produced when all indicators are off.
OFF
No effect is selected when no EFFECT indicator is lit.
CHORUS
Shimmering, broadening effect
SYMPHONIC
Adds a deep, symphonic backdrop
TREMOLO
Tremolo effect
DELAY
Echo effect
NOTE
• The default effect type (including OFF) and depth settings are different for
each voice.
Adjusting Effect Depth.............................................................................
CHORUS
SYMPHONIC
TREMOLO
DELAY
EFFECT
Effect depth can be individually adjusted for the selected voice by
SONG
SELECT
–
/ NO+ / YES
using the [–/NO] and [+/YES] buttons while holding the [EFFECT]
button. The depth range is from 0 through 20 (the current depth setting
appears on the LED display while the [EFFECT] button is held). A
setting of “0” produces no effect, while a setting of “20” produces
maximum effect depth. Press the [–/NO] and [+/YES] buttons simultaneously while holding the [EFFECT] button to recall the default
setting for the current voice (the default depth settings are different for
each voice).
Brilliance (CLP-880/860/840)
This control can be used to change the tonality or “timbre” of the sound
output. The control range is from MELLOW to BRIGHT.
BRILLIANCE
BRIGHT
For a brighter or “sharper” tone, slide the control towards the
BRIGHT position. For a “rounder” more mellow tone, slide the control
towards the MELLOW position.
NOTE
MELLOW
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
• When the BRILLIANCE is set to BRIGHT, the overall sound will be
slightly louder. If the MASTER VOLUME is set at a high level the sound
may become distorted. If so, lower the MASTER VOLUME level.
CLP-880/860/840/820/820S
19
The Pedals
The CLP-820
produce a range of expressive effects similar to those produced by the
pedals on an acoustic piano.
S
has two and other models have three foot pedals that
CLP-880/860/840/820
Soft pedal
Sostenuto pedal
CLP-820S
Soft/Sostenuto pedal
Damper pedal
Damper pedal
Damper (Right) Pedal................................................................................
The damper pedal functions in the same way as a damper pedal on
an acoustic piano. When the damper pedal is pressed notes played have
a long sustain. Releasing the pedal immediately stops (damps) any
sustained notes.
On the CLP-880/860, when GRAND PIANO, CLASSICAL PIANO, or JAZZ PIANO is selected the damper pedal also produces a
special “resonance” that simulates the ring of the strings and the sound
board of an acoustic piano.
The CLP-880/860 damper pedal additionally features continuous
damping. This allows you to create shorter effects by pressing the
damper pedal down only part of the way.
NOTE
• On the CLP-880/860, soundboard depth and damper pedal mode (switch/
continuous) settings can be changed using the “Pedal Functions” (page
32) in the function mode.
Sostenuto (Center) Pedal (except for CLP-820S) .....................
If you play a note or chord on the keyboard and press the sostenuto
pedal while the note(s) are held, those notes will be sustained as long as
the pedal is held (as if the damper pedal had been pressed) but all
subsequently played notes will not be sustained. This makes it possible
to sustain a chord, for example, while other notes are played “staccato.”
NOTE
• Organ and string voices will continue to sound for as long as the sostenuto pedal is depressed.
Soft (Left) Pedal...............................................................................................
The soft pedal reduces the volume and slightly changes the timbre of
notes played while the pedal is pressed. The soft pedal will not affect
notes which are already playing when it is pressed.
The left pedal can also be assigned to song start/stop operation (or
sostenuto in the case of the CLP-820S) via the “Left Pedal Mode”
described on page 32.
CLP-880/860/840/820/820S
20
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Touch Sensitivity
Four different types of keyboard touch sensitivity — HARD, MEDIUM, SOFT
or FIXED — can be selected to match different playing styles and preferences.
HARD
MEDIUM
SOFT
TOUCH
To select a touch sensitivity type press the [TOUCH] button a few
times until the indicator corresponding to the desired type lights (the
indicators light in sequence each time the [TOUCH] button is pressed).
HARD
The HARD setting requires the keys to be played quite hard to
produce maximum loudness.
MEDIUM
The MEDIUM setting produces a fairly “standard” keyboard response.
This is the initial factory default setting.
SOFT
The SOFT setting allows maximum loudness to be produced with
relatively light key pressure.
FIXED (no indicator lit)
All notes are produced at the same volume no matter how hard the
keyboard is played.
When the FIXED type is selected, the volume of notes played in the
FIXED mode can be set by using the [–/NO] and [+/YES] buttons
while the [TOUCH] button is held (the current volume level appears on
the display). The volume range is from 1 through 127. The default
setting is 64.
NOTE
• This setting does not change the weight of the keyboard.
• The touch sensitivity type and volume set in the FIXED mode will become
the common setting for all voices.
TRANSPOSE
Transposition
The Clavinova’s TRANSPOSE function makes it possible to shift the pitch of
the entire keyboard up or down in semitone intervals up to a maximum of 12
semitones (i.e. a maximum of one octave up or down). “Transposing” the pitch
of the Clavinova keyboard facilitates playing in difficult key signatures, and you
can easily match the pitch of the keyboard to the range of a singer or other
instrumentalist.
SONG
SELECT
–
/ NO+ / YES
Use the [–/NO] or [+/YES] button while holding the [TRANS-
POSE] button to transpose down or up as required. The transposition
range is from “–12” (down one octave) through “0” (normal pitch) to
“12” (up one octave). The amount of transposition appears on the LED
display while the [TRANSPOSE] button is held. The default transpose
setting is “0”.
NOTE
• The [TRANSPOSE] button indicator remains lit when a transpose setting
other than “0” is selected.
• Notes below and above the A-1 … C7 range of the Clavinova sound one
octave higher and lower, respectively.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
21
Tuning
Tuning makes it possible to adjust the pitch of the Clavinova over a 427.0 Hz
… 453.0 Hz (corresponding to the A3 note’s Hz) range in approximately 0.2
Hertz intervals. Pitch control is useful for tuning the Clavinova to match other
instruments or recorded music.
A-1B
-1
A
A#
-1
3
C
3
B
Tuning Up...............................................................................................................
ZTo tune up (raise pitch), hold the A-1 and B-1 keys simultaneously.
XPress any key between C3 and B3. Each time a key in this range is
pressed the pitch is increased by approximately 0.2 Hz.
The [–/NO] and [+/YES] buttons can also be used to tune down or up,
SELECT
–
/
NO +
SONG
/
YES
respectively, in
approximately
[+/YES] buttons simultaneously to recall standard tuning (A3 = 440
Hz).
1 Hz increments. Press the [–/NO] and
CRelease the A-1 and B-1 keys.
-1
3
C
3
B
Tuning Down.......................................................................................................
ZTo tune down (lower pitch), hold the A-1 and A#-1 keys simulta-
neously.
XPress any key between C3 and B3. Each time a key in this range is
pressed the pitch is decreased by approximately 0.2 Hz.
SONG
SELECT
–
/ NO+ / YES
The [–/NO] and [+/YES] buttons can also be used to tune down or up,
respectively, in
approximately
1 Hz increments. Press the [–/NO] and
[+/YES] buttons simultaneously to recall standard tuning (A3 = 440
Hz).
A#
A-1B
CRelease the A-1 and A#-1 keys.
-1
-1
3
C
3
B
To Restore Standard Pitch...................................................................
ZTo restore the default pitch (A3 = 440 Hz), hold the A-1, A#-1 and
B-1 keys simultaneously.
XPress any key between C3 and B3.
CRelease the A-1, A#-1 and B-1 keys.
In terms of “Hertz”, the overall tuning range is from 427.0 Hz to 453.0
Hz. The current tuning setting is shown on the LED display while the tuning
is being adjusted. Tenths of a Hertz are indicated on the LED display by the
appearance and position of one or two dots, as in the following example:
Display Value
440 440.0
4.40 440.2
44.0 440.4
440. 440.6
4.40. 440.8
NOTE
• An alternative tuning method is available in the Function mode — page 28.
CLP-880/860/840/820/820S
22
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Metronome & Tempo Control
The Clavinova built-in metronome is a convenient feature for practice, and it
can also provide a solid rhythmic guide when recording using the Recorder
feature, described in the next section.
The Metronome
Beat indicator
METRO-
NOME
METRO-
NOME
SONG
SELECT
–
/ NO+ / YES
The metronome sound is alternately turned on and off by pressing
the [METRONOME] button. When on, the beat indicator flashes at the
current tempo.
Metronome Time Signature................................................................
The time signature (beat) of the metronome can be set by using the
[–/NO] and [+/YES] buttons while holding the [METRONOME]
button. You can set the beat to 0, 2, 3, 4 or 6 (the current setting appears
on the LED display while the [METRONOME] button is held). Press
the [–/NO] and [+/YES] buttons simultaneously while holding the
[METRONOME] button to recall the default setting “0” (no accent).
Metronome Volume Function ...........................................................
The volume of the metronome sound can be adjusted via the Metro-
nome Volume function in the Function mode—page 33.
Tempo Control
SONG
SELECT
–
/
NO +
/
YES
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The tempo of the metronome and recorder playback (the recorder is
described in the next section) can be set from 32 to 280 beats per
minute by using the [TEMPO t/s] buttons. The selected tempo will
appear on the LED display while in the normal play mode and while the
[TEMPO t/s] buttons are being used to adjust the tempo in the
recording/playback mode. The default tempo (120 or the recorded song
tempo when the recorder contains data and the playback track indicator
is lit) can be recalled by simultaneously pressing the [t] and [s]
buttons.
CLP-880/860/840/820/820S
23
Using the Recorder
The Clavinova features a two-track recorder that let you record what you play
on the keyboard and then play it back. Two tracks mean that you can “overdub”
one part on top of another, using a different voice if you like. The recorder feature
is a useful adjunct to any keyboard study program, since it lets you hear exactly
how you sound from the listener’s perspective. It can also be just plain fun.
The recorder actually records the following data:
■ Entire Song
● Tempo ● Time signature (beat) ● Reverb type (including OFF)
● Effect type (CLP-880/860/840)
■ Individual Tracks
● Notes played ● V oice selection ● V oice variation
● Dual mode voices ● Split mode voices (CLP-880/860)
● Damper pedal ● Soft pedal
● Sostenuto pedal (not recorded as an initial setting)
● Effect depth (CLP-880/860/840) ● Reverb depth
● Dual balance (F3) ● Dual detune (F3) ● Dual octave shift (F3)
● Split balance (F4: CLP-880/860) ● Split octave shift (F4: CLP-880/860)
Recording
GRAND
PIANO
CLASSICAL
PIANO
RECORDER
12
START
STOP
RECORDER
12
START
/
STOP
CLP-880/860
/
JAZZ
PIANO
REC
REC
ROCK
PIANO
E. PIA
Make All Necessary Initial Settings............................................
Before actually beginning to record, select the voice you want to
record with (or voices if you will be using the dual or split mode). You
might also want to set the volume and tempo controls.
Engage the Record Ready Mode ..................................................
Press the RECORDER [REC] button to engage the record ready mode
(recording does not actually start yet). The record ready mode can be
disengaged before recording by pressing the [REC] button a second time.
• The record ready mode cannot be engaged while the demo/piano song
mode is engaged.
Select the Record Track .........................................................................
When the record mode is engaged in the previous step, the last-
recorded track will automatically be selected for recording and its indicator — i.e. the [1] or [2] button indicator — will glow red. If you want to
record on a different track, press the appropriate track button so that its
indicator glows red.
• The track button indicators of tracks which contain previously recorded data
will glow green (unless the track is turned off as described below). The
previously-recorded data on the non-record track will normally be played
back as you record, so you can play along with a previously-recorded track.
If you don’t want to hear the previously recorded track as you record (when
you want to record a song different from what you recorded on the previous
track etc.,), press the playback track button before pressing the [REC]
button (step 1, above) so that its indicator goes out.
• Recording on a track which already contains data will erase all previous
data on that track.
• When the record mode is engaged the amount of memory available for
recording will be shown on the LED display in approximate kilobytes
(starting at “50” on the CLP-880/860 and “25” on the CLP-840/820/820S),
and the rightmost dot on the LED display will flash at the current METRONOME tempo setting.
CLP-880/860/840/820/820S
24
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
Using the Recorder
Start Recording................................................................................................
Recording will begin automatically as soon as you play a note on the
keyboard or press the [START/STOP] button. The current measure
number will appear on the display while recording.
RECORDER
12
START
/
REC
STOP
RECORDER
12
START
/
REC
STOP
RECORDER
12
START
/
REC
STOP
• The left pedal can be assigned to start and stop recording via the “Left
Pedal Mode” function described on page 32.
• If the metronome was on when you started recording, you’ll be able to
keep time with the metronome while recording, but the metronome sound
will not be recorded.
• You can record up to a maximum of about 10,000 notes on the CLP-880/
860 or 5,000 notes on the CLP-840/820/820S, depending on pedal usage
and other factors. The record track indicator will begin to flash when
recorder memory is almost full. If the memory becomes full during
recording, “
automatically. (All recorded data up to that point will be retained.)
FUL
” will appear on the display and recording will stop
Stop Recording................................................................................................
Press either the RECORDER [REC] or [START/STOP] button to
stop recording.
The indicator of the recorded track will glow green to indicate that it
now contains data.
Changing the Initial Settings.............................................................
The initial voice, tempo, reverb type, reverb depth, and effect settings
made in step 1 of the recording procedure are actually recorded by the
Clavinova.
These initial settings can be changed after the recording is finished by
pressing the [REC] button to engage the record ready mode, pressing the
appropriate track button, making the required changes, and then pressing
the [REC] button again to exit from the record ready mode and register
the changes.
If you do this, be careful not to press the [START/STOP] button or a
key on the keyboard, either of which will start recording and erase all
previous recorded data on the selected track.
It is possible to cancel the operation even after changes have been
made: change tracks and then press the [REC] button to exit from the
record mode (this also cancels data for the entire song).
• The following data for initial settings cannot be changed: “Dual balance
(F3)”, “Dual detune (F3)”, “Dual octave shift (F3)”, “Split balance (F4:CLP880/860)” or “Split octave shift (F4:CLP-880/860)”.
RECORDER
12
Erasing a Single Track .............................................................................
All data can be erased from either of the recorder’s tracks by engag-
ing the record mode, selecting the track you want to erase, and then
START
/
REC
STOP
Press twice.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
pressing the [START/STOP] button twice without recording any data.
CLP-880/860/840/820/820S
25
Using the Recorder
Playback
RECORDER
12
START
/
REC
STOP
To play back what you’ve recorded, first make sure that the green track
indicators of the tracks you want to play are lit. If not, press the corresponding
track button(s) so that they are lit. Then press the RECORDER [START/
STOP] button. Playback starts from the beginning of the recorded data, and
will stop automatically at the end of the recorded data. You can also stop
playback at any time by pressing the [START/STOP] button.
To mute a track so that it doesn’t play back, press the corresponding track
button so that its indicator goes out (press again to turn the track back on).
The current measure number appears on the display during playback.
• It is possible to play along on the keyboard during playback. In this case, the
playback voice and the voice you play on the keyboard are not the same. The
playback voice is the voice that was set when the data was recorded. The voice
you play on the keyboard is the voice that is selected on the panel.
• The playback volume and tempo can be adjusted by using the [MASTER VOLUME] control and [TEMPO ▼/▲] buttons (press both [TEMPO ▼/▲] buttons
simultaneously to recall the default tempo).
• All recorder data will be retained in memory for about one week after the power is
turned off. If you want to keep your recorded data for longer periods, turn the power
on for a few minutes at least once a week. It is also possible to store it to an
external MIDI storage device such as the Yamaha MIDI Data Filer MDF3 by using
the Bulk Data Dump function described on page 36.
• The track indicators will not light automatically when the power is turned on even if
the recorder contains data. It is therefore necessary to press the track buttons so
that the corresponding green indicators light before starting RECORDER playback.
It is also a good idea to press the track buttons to check if the tracks contain data
before recording. If the green indicator lights when the corresponding track button
is pressed, that track contains data which will be erased and replaced by the
newly-recorded data.
• If the metronome is being used during playback, the metronome will automatically
stop when playback is stopped.
• During recorder playback, the volume of a track which is turned off will always be
“0” (i.e. the “Piano Song Part Cancel Volume” function — page 33 — only affects
piano song playback.
• The playback data is not transmitted via the MIDI OUT connector.
• Playback cannot be started when the demo/piano song mode is engaged.
• Playback cannot be started when the recorder contains no data, or when both track
buttons are off.
• When using REVERB or EFFECT during playback, depending upon the conditions
one reverb type and one effect type will take priority.
CLP-880/860/840/820/820S
26
RECORDER
12
START
/
REC
STOP
Synchro Start ....................................................................................................................
When the Synchro Start function is engaged, recorder playback will begin
automatically as soon as you start playing on the keyboard.
To engage the Synchro Start function press the [START/STOP] button
while holding a track button which is ON. The rightmost dot on the display will
flash at the current tempo. (Repeat the previous operation to disengage the
Syncro Start function.) Playback will then start as soon as you begin playing on
the keyboard.
If you hold a track button which is OFF while pressing the [START/STOP]
button, that track will be turned ON and the Synchro Start mode will be engaged.
Left Pedal Start/Stop.................................................................................................
The left pedal can be assigned to start and stop recorder playback via the
“Left Pedal Mode” function described on page 32. This is convenient for
starting playback of the recorded part anytime after you have started playing.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Function Mode
The [FUNCTION] button provides access to a range of functions that give the
Clavinova extraordinar y versatility. The functions are categor ized in groups as
follows:
FUNCTION
TEMPO
FUNCTION
CLP-840/
CLP-880/
820/820S 860
F1 F1 Tuning............................................................. 28
F2 F2 Scale ............................................................... 28
F3 F3 Dual Mode Functions .................................... 29
– F4 Split Mode Functions .................................... 30
F4 – Left Pedal Mode ............................................. 32
– F5 Pedal Functions ............................................. 32
F5 F6 Metronome Volume........................................ 33
F6 F7 Piano Song Part Cancel Volume .................. 33
F7 F8 MIDI Functions ............................................... 34
F8 F9 Backup Functions.......................................... 37
To Select a Function … ...........................................................................
ZPress the [FUNCTION] button so that its indicator lights.
NOTE
• Functions cannot be selected during demo/piano song playback or when
the recorder is in operation.
XUse the FUNCTION [<] and [>] buttons to select the desired
function: F1 through F8 on the CLP-840/820/820S; F1 through F9
on the CLP-880/860.
● Operation Example
Press [+/YES]
Use FUNCTION [<], [>]
Press [–/NO] or [+/YES]
once
Use [–/NO], [+/YES]
(sub-mode)
CIn the case of the Scale (F2), Dual Mode (F3), Split Mode (F4:
CLP-880/860), Pedal Functions (F5: CLP-880/860), MIDI (F7:
CLP-840/820/820S, F8: CLP-880/860), and Backup (F8: CLP-840/
820/820S, F9: CLP-880/860) functions, you will have to press the
[+/YES] button once to enter the respective sub-mode after the
function has been selected, and then use the FUNCTION [<] and
[>] buttons again to select the desired sub-function.
NOTE
• The Dual or Split (CLP-880/860) mode must be engaged before the F3
and F4 functions can be selected, respectively. If the corresponding mode
is not engaged, “
corresponding sub-mode will not be available.
• The Dual mode can be engaged while in the Function mode, but the
Function mode must be exited before the Split mode (CLP-880/860) can
be engaged.
F3.-
” or “
F4.-
” will appear on the display and the
VSet the function as required by using the [–/NO] and [+/YES]
buttons (see the individual function descriptions, below).
NOTE
• After selecting the function, the current setting will be displayed when the
[–/NO] or [+/YES] button is pressed for the first time.
BPress the [FUNCTION] button so that its indicator goes out to exit
from the function mode.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
27
The Function Mode
F1
F2
Tuning
In addition to the tuning method described on page 22, overall tuning can also be accom-
plished via the F1 function.
After selecting “F1”, use the [–/NO] and [+/YES] buttons to lower or raise the pitch in
approximately 0.2 Hz increments (the first time the [–/NO] or [+/YES] button is pressed
simply switches to the tuning value display without actually changing the tuning). The overall
tuning range is from 427.0 Hz to 453.0 Hz (corresponding to the A3 note’s Hz). Press the
[–/NO] and [+/YES] buttons simultaneously to recall the default value “440 Hz”.
Tenths of a Hertz are indicated on the LED display by the appearance and position of one
or two dots, as in the following example:
Display Value
440 440.0
4.40 440.2
44.0 440.4
440. 440.6
4.40. 440.8
Scale
After selecting “F2.Y”, press the [+/YES] button to engage the scale function sub-mode,
then use the FUNCTION [<] and [>] buttons to select the desired scale function, as listed
below.
F2.1: Scale..........................................................................................................................................................
In addition to the standard Equal Temperament tuning, the Clavinova includes 6 classic
tunings that you can select and use to play music of the corresponding period, or experiment
with in a more modern context. The tunings are:
1: Equal Temperament 5: Mean Tone
2: Pure Major 6: Werckmeister
3: Pure Minor 7: Kirnberger
4: Pythagorean
Use the [–/NO] and [+/YES] buttons to select the number of the desired tuning. Press the
[–/NO] and [+/YES] buttons simultaneously to recall the default settings (Equal Temperament
tuning).
F2.2: Base Note.............................................................................................................................................
Unlike Equal Temperament tuning, these classic tunings must be tuned to a specific key.
Use the [–/NO] and [+/YES] buttons to select the key you want the previously selected tuning
to be based. The selected key will appear on the display, followed by a low bar if flat (e.g.
“A_”) or a high bar if sharp (e.g. “F~”).
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default settings “C”.
CLP-880/860/840/820/820S
28
• The base note setting is effective for tunings other than the Equal Temperament tuning.
NOTE
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Function Mode
F3
Dual Mode Functions
After selecting “F3.Y”, press the [+/YES] button to engage the dual-mode function sub-
mode, then use the FUNCTION [<] and [>] buttons to select the desired dual mode function, as listed below.
If the Dual mode is not engaged “F3.-” will appear instead of “F3.Y” and the Dual mode
functions cannot be selected. If this happens engage the Dual mode and proceed.
■ SHORTCUT: You can jump directly to the dual-mode functions (F3) by pressing the
[FUNCTION] button while holding the two dual-mode voice selectors.
NOTE
• Dual mode function settings are set individually for each voice combination.
F3.1: Dual Balance.....................................................................................................................................
The volume levels of the two voices combined in the dual mode can be adjusted as re-
quired by using this function. Use the [–/NO] and [+/YES] buttons to adjust the balance as
required. The balance range is from 0 through 20. A setting of “10” produces equal balance
between the two dual-mode voices. Settings below “10” increase the volume of the 2nd Voice
in relation to the 1st Voice, and settings above “10” increase the volume of the 1st Voice in
relation to the 2nd Voice (“1st” and “2nd” is explained on page 16). Press the [–/NO] and [+/
YES] buttons simultaneously to recall the default setting (different for each voice combination).
You can set one voice as the main voice, and another voice as a softer, mixed voice.
F3.2: Dual Detune.......................................................................................................................................
This function makes it possible to detune the 1st and 2nd dual-mode Voices to create a
thicker sound. Use the [–/NO] and [+/YES] buttons to set the amount of detuning as required.
The detune range is from –10 through 10. A setting of “0” sets both voices to the same pitch.
Settings below “0” increase the pitch of the 2nd Voice in relation to the 1st Voice, and settings
above “0” increase the pitch of the 1st Voice in relation to the 2nd Voice (“1st” and “2nd” is
explained on page 16). Press the [–/NO] and [+/YES] buttons simultaneously to recall the
default setting (different for each voice combination).
F3.3: 1st Voice Octave Shift............................................................................................................
F3.4: 2nd Voice Octave Shift ..........................................................................................................
Depending on which voices you combine using the dual mode, the combination may sound
better if one of the voices is shifted up or down an octave. Use the [–/NO] and [+/YES]
buttons to set the octave of the 1st or 2nd Voice as required (“1st” and “2nd” is explained on
page 16). The available settings are “0” for normal pitch, “–1” to shift the pitch down one
octave, and “1” to shift the pitch up one octave. Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting (different for each voice combination).
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
29
The Function Mode
F3.5: 1st Voice Effect Depth (CLP-880/860/840)....................................................................
F3.6: 2nd Voice Effect Depth (CLP-880/860/840)..................................................................
2nd dual-mode Voices (“1st” and “2nd” is explained on page 16). Use the [–/NO] and [+/
YES] buttons to set the effect depth for the corresponding voice as required. The depth range
is from 0 through 20. A setting of “0” produces no effect, while a setting of “20” produces
maximum effect depth. Press the [–/NO] and [+/YES] buttons simultaneously to recall the
default setting (different for each voice combination).
F3.5: Reset (CLP-820/820S) .......................................................................................................................
F3.7: Reset (CLP-880/860/840) .................................................................................................................
button to reset the values. “End” will appear on the display when all functions have been
reset.
These functions make it possible to individually set the depth of the effect for the 1st and
NOTE
• The effect depth settings cannot be changed unless the EFFECT is ON. The Function mode must be
exited before EFFECT can be turned ON.
This function resets all dual-mode functions to their default values. Press the [+/YES]
F4
CLP-880/860 Split Mode Functions
After selecting “F4.Y”, press the [+/YES] button to engage the split-mode function sub-
mode, then use the FUNCTION [<] and [>] buttons to select the desired split mode function, as listed below.
If the Split mode is not engaged “F4.-” will appear instead of “F4.Y” and the Split mode
functions cannot be selected. Also note that you must exit from the Function mode before the
Split mode can be engaged.
■ SHORTCUT: You can jump directly to the split-mode functions (F4) by pressing the
[FUNCTION] button while holding the [SPLIT] button.
NOTE
• Split mode function settings are set individually for each voice combination.
F4.1: Split Point ............................................................................................................................................
In addition to the split point setting method described on page 17, the split point can be set
via this function. Use the [–/NO] and [+/YES] buttons to set the split point as required, or
simply press the appropriate key on the keyboard: from “A-1” to “C7”. Press the [–/NO] and
[+/YES] buttons simultaneously to recall the default setting “F#2”.
CLP-880/860/840/820/820S
30
F4.2: Split Balance.....................................................................................................................................
The volume levels of the two voices combined in the split mode can be adjusted as re-
quired by using this function. Use the [–/NO] and [+/YES] buttons to adjust the balance as
required. The balance range is from 0 through 20. A setting of “10” produces equal balance
between the two split-mode voices. Settings below “10” increase the volume of the Left Voice
in relation to the Right Voice, and settings above “10” increase the volume of the Right Voice
in relation to the Left Voice. Press the [–/NO] and [+/YES] buttons simultaneously to recall
the default setting (different for each voice combination).
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Function Mode
F4.3: Right Voice Octave Shift......................................................................................................
F4.4: Left Voice Octave Shift..........................................................................................................
Depending on which voices you combine using the split mode, the combination may sound
better if one of the voices is shifted up or down an octave. Use the [–/NO] and [+/YES]
buttons to set the octave of the Left or Right Voice as required. The available settings are “0”
for normal pitch, “–1” to shift the pitch down one octave, and “1” to shift the pitch up one
octave. Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting
(different for each voice combination).
Set according to the pitch extent for the song you want to play.
F4.5: Right Voice Effect Depth ......................................................................................................
F4.6: Left Voice Effect Depth..........................................................................................................
These functions make it possible to individually set the depth of the effect for the Left and
Right split-mode Voices. Use the [–/NO] and [+/YES] buttons to set the effect depth for the
corresponding voice as required. The depth range is from 0 through 20. A setting of “0”
produces no effect, while a setting of “20” produces maximum effect depth. Press the [–/NO]
and [+/YES] buttons simultaneously to recall the default setting (different for each voice
combination).
NOTE
• The effect depth settings cannot be changed unless the EFFECT is ON. The Function mode must be
exited before EFFECT can be turned ON.
F4.7: Damper Range................................................................................................................................
The Damper Range function determines whether the damper pedal affects the Right Voice,
the Left Voice, or both the Left and Right Voices in the split mode. Use the [–/NO] and [+/
YES] buttons to select “2” for the Left Voice, “1” for the Right Voice, or “ALL” for both
voices. Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting
“ALL”.
F4.8: Reset .........................................................................................................................................................
This function resets all split-mode functions to their default values. Press the [+/YES]
button to reset the values. “End” will appear on the display when all functions have been
reset.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
31
The Function Mode
F4
F5
CLP-840/820/820S Left Pedal Mode
This function sets the left pedal for normal soft-pedal operation, for song start/stop opera-
tion, or for sostenuto (CLP-820S only) operation. Use the [–/NO] and [+/YES] buttons to
select the desired left-pedal mode. “1” is the normal soft-pedal mode, “2” is the start/stop
mode, and “3” is the sostenuto mode (CLP-820S only). When the start/stop mode is selected,
the left pedal functions in the same way as the panel [START/STOP] button. Press the
[–/NO] and [+/YES] buttons simultaneously to recall the default setting “1”.
CLP-880/860 Pedal Functions
After selecting “F5.Y”, press the [+/YES] button to engage the pedal functions sub-mode,
then use the FUNCTION [<] and [>] buttons to select the desired pedal functions, as listed
below.
F5.1: Left Pedal Mode ............................................................................................................................
This function conveniently lets you set the left pedal for normal soft pedal operation, or for
song start/stop operation. Use the [–/NO] and [+/YES] buttons to select the desired leftpedal mode. Press the [–/NO] and [+/YES] buttons simultaneously to recall the default
setting “1”.
1: Soft The left pedal functions as the soft pedal.
2: Start/Stop The left pedal functions in the same manner as the [START/STOP] button.
F5.2: Damper Mode...................................................................................................................................
This function lets you set how the damper pedal affects the sustain sound. There are two
modes for pedal operation.
1: Switch In this mode the pedal acts as a simple on/off switch for sustain.
2: Continuous In this mode the pedal continuously changes the amount of sustain (in eight-
step gradations) i.e., the further down you press the pedal the longer the sound
sustains.
Use the [–/NO] and [+/YES] buttons to select the desired damper mode. Press the [–/NO]
and [+/YES] buttons simultaneously to recall the default setting “2”.
F5.3: Soundboard Depth.....................................................................................................................
Certain piano voices (GRAND PIANO, CLASSICAL PIANO, and JAZZ PIANO) feature
a special effect which recreates the ring of the strings and the soundboard resonance of an
actual acoustic piano when the damper pedal is pressed. This function lets you adjust the
depth of this effect. Use the [–/NO] and [+/YES] buttons to set the effect depth as required.
The effect depth range is from 0 through 20. A setting of “0” produces no effect, while a
setting of “20” produces maximum effect depth. Press the [–/NO] and [+/YES] buttons
simultaneously to recall the default setting “12”.
CLP-880/860/840/820/820S
32
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Function Mode
F5
F6
F6
F7
CLP-840/820/820S Metronome Volume
CLP-880/860 Metronome Volume
■ SHORTCUT: You can jump directly to the metronome functions by pressing the [FUNC-
TION] button while holding the [METRONOME] button.
The volume of the metronome sound can be changed. After selecting “F5” or “F6”, use
the [–/NO] and [+/YES] buttons to set the metronome volume as required. The volume range
is from 1 through 20. A setting of “1” produces minimum sound, while a setting of “20”
produces maximum metronome volume. Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting “10”.
CLP-840/820/820S Piano Song Part Cancel Volume
CLP-880/860 Piano Song Part Cancel Volume
This function sets the volume at which a “canceled” part is played during piano song
playback (see page 15 for information on the “part-cancel” function). Use the [–/NO] and [+/
YES] buttons to set the volume as required. The volume range is from 0 through 20. A setting
of “0” produces no sound, while a setting of “20” produces maximum volume. Press the [–/
NO] and [+/YES] buttons simultaneously to recall the default setting “5”.
Adjust the part volume to a comfortable level to use the “canceled” part as a guide to play
along with. Set to “0” if you don’t want to hear the part.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
33
The Function Mode
F7
F8
CLP-840/820/820S MIDI Functions
CLP-880/860 MIDI Functions
● A Brief Introduction to MIDI
MIDI Cable
MIDI INMIDI OUT
DOU-10
Clavinova
note and velocity (touch response) information via the MIDI OUT connector whenever a note is played on the
keyboard. If the MIDI OUT connector is connected to the MIDI IN connector of a second keyboard (synthesizer,
etc.) or a tone generator (essentially a synthesizer with no keyboard), the second keyboard or tone generator will
respond precisely to notes played on the original transmitting keyboard. The result is that you can effectively
play two instruments at once, providing thick multi-instrument sounds.
Data Being Recorded
Playback Data
MIDI IN MIDI INMIDI OUTMIDI OUT
DOU-10
Clavinova
MIDI, the Musical Instrument Digital Interface, is a worldstandard communication interface that allows MIDI-compatible
musical instruments and equipment to share musical information and
control one another. This makes it possible to create “systems” of
MIDI instruments and equipment that offer far greater versatility and
control than is available with isolated instruments. For example,
most MIDI keyboards (including the Clavinova, of course) transmit
This same type of musical information transfer is used for MIDI
sequence recording. A sequence recorder can be used to “record”
MIDI data received from a Clavinova, for example. When the
recorded data is played back, the Clavinova automatically “plays”
the recorded performance in precise detail.
The examples given above really only scratch the surface. MIDI
can do much, much more. The Clavinova MIDI functions allow it to
be used in fairly sophisticated MIDI systems.
After selecting “F7.Y” or “F8.Y”, press the [+/YES] button to engage the MIDI function sub-
mode, then use the FUNCTION [<] and [>] buttons to select the desired MIDI function, as listed
below.
• The rear-panel HOST SELECT switch must be set to “MIDI” in order to use the MIDI connectors. When you use
NOTE
the TO HOST connector, set the HOST SELECT switch to the appropriate position for the type of computer you
are using (see page 38). In this situation, all MIDI settings described below will have affect on the MIDI signal in
and out of the TO HOST connector.
• Always use a high-quality MIDI cable to connect MIDI OUT to MIDI IN terminals. Never use MIDI cables longer
than about 15 meters, since cables longer than this can pick up noise which can cause data errors.
F7.1/F8.1: MIDI Transmit Channel Selection.............................................................................
F7.2/F8.2: MIDI Receive Channel Selection................................................................................
MIDI OUT
DOU-10
MIDI IN MIDI THRU
Tone Generator
(Set to receive on MIDI
channel 2)
Clavinova
(Set to receive on MIDI channel 1)
MIDI IN
MIDI sequence recorder could be used to “play” two different instruments or tone generators. One of
the instruments or tone generators could be set to receive only on channel 1, while the other is set to
receive on channel 2. In this situation the first instrument or tone generator will respond only to
channel-1 information transmitted by the sequence recorder, while the second instrument or tone
generator will respond only to channel-2 information. This allows the sequence recorder to “play”
two completely different parts on the receiving instruments or tone generators.
The MIDI system allows transmission
and reception of MIDI data on 16 different channels. Multiple channels have
been implemented to allow selective
control of certain instruments or devices
connected in series. For example, a single
CLP-880/860/840/820/820S
34
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Function Mode
In any MIDI control setup, the MIDI channels of the transmitting and receiving equipment must
be matched for proper data transfer. A “Multi-timbre” receive mode is also available, which allows
simultaneous reception of different parts on all 16 MIDI channels, allowing the Clavinova to play
multi-channel song data received from a music computer or sequencer. There’s also a “1-2” mode
which allows simultaneous reception on channels 1 and 2.
Use the [–/NO] and [+/YES] buttons to select the desired transmit or receive channel. The
transmit channel parameter can also be turned “OFF” if you don’t want the Clavinova to transmit
any MIDI data. To select the multi-timbre receive mode, set the receive channel to “ALL”. Select
“1-2” for multi-timbre reception on channels 1 and 2 only.
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting: transmit = “1”;
receive = “ALL”.
NOTE
• In the dual mode first voice data is transmitted on its set channel, and in the split mode right voice data is
transmitted on its set channel. In the dual mode second voice data is transmitted on the next greater channel
number of the set channel, and in the split mode left voice data is transmitted on the next greater channel
number of the set channel. In either mode, no data is transmitted if the transmit channel is set to “OFF”.
• Demo/piano song data and recorder playback data are not transmitted via MIDI.
• No MIDI reception occurs when the demo/piano song mode is engaged.
• Program change and other like channel messages received will not affect the Clavinova’s panel settings or
what is being played on the keyboard.
F7.3/F8.3: Local Control ON/OFF...........................................................................................................
“Local Control” refers to the fact that, normally, the
AUX IN
L
OUT PUT
RMIDI OUT
MIDI
L
R
IN
Clavinova keyboard controls its internal tone generator,
allowing the internal voices to be played directly from
DOU-10
the keyboard. This situation is “Local Control On”
since the internal tone generator is controlled locally by
Clavinova
its own keyboard.
Local control can be turned OFF, however, so that the Clavinova keyboard does not play the
internal voices, but the appropriate MIDI information is still transmitted via the MIDI OUT connector when notes are played on the keyboard. At the same time, the internal tone generator responds to
MIDI information received via the MIDI IN connector.
When using the DOU-10 Disk Orchestra Unit with the Clavinova, for example, Local Control
should be turned OFF when recording using the DOU-10 voices only, and ON when recording the
Clavinova voices while listening to playback of the DOU-10 voices.
Use the [–/NO] and [+/YES] buttons to turn local control “On” or “OFF”.
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting “On”.
F7.4/F8.4: Program Change ON/OFF.................................................................................................
Normally the Clavinova will respond to MIDI program change numbers received from an external keyboard or other MIDI device, causing the correspondingly numbered voice to be selected on
the corresponding channel (the keyboard voice does not change). The Clavinova will normally also
send a MIDI program change number whenever one of its voices is selected, causing the correspondingly numbered voice or program to be selected on the external MIDI device if the device is set up to
receive and respond to MIDI program change numbers.
This function makes it possible to cancel program change number reception and transmission so
that voices can be selected on the Clavinova without affecting the external MIDI device.
Use the [–/NO] and [+/YES] buttons to turn program change transmission and reception “On” or
“OFF”.
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting “On”.
NOTE
• For information on program change numbers for each of the Clavinova’s voices, refer to page 44 in the MIDI
Data Format section.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
35
The Function Mode
F7.5/F8.5: Control Change ON/OFF ........................................................................................
external MIDI device or keyboard, causing the voice on the corresponding channel to be
affected by pedal and other “control” settings received from the controlling device (the keyboard voice is not affected). The Clavinova also transmits MIDI control change information
when one of its pedals or other appropriate controls are operated.
that, for example, the Clavinova pedals and other controls can be operated without affecting
an external MIDI device.
“On” or “OFF”.
F7.6/F8.6: MIDI Transmit Transpose .......................................................................................
or down in semitone increments by up to plus or minus 12 semitones. The pitch of the
Clavinova itself is not affected.
Normally the Clavinova will respond to MIDI control change data received from an
This function makes it possible to cancel control change data reception and transmission so
Use the [–/NO] and [+/YES] buttons to turn control change transmission and reception
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting “On”.
NOTE
• For information on control changes that can be used with the Clavinova, refer to the MIDI Data
Format on page 43.
This function allows the MIDI note data transmitted by the Clavinova to be transposed up
Use the [–/NO] and [+/YES] buttons to set the desired amount of MIDI transmit transposi-
tion. The range is from “–12” (down one octave) through “0” (no transposition) to “12” (up
one octave).
Press the [–/NO] and [+/YES] buttons simultaneously to recall the default setting “0”.
F7.7/F8.7: Panel/Status Transmit ...............................................................................................
This function causes all the current Clavinova panel settings (selected voice, etc.) to be
transmitted via the MIDI OUT terminal. This is particularly useful if you will be recording
performances to a MIDI sequence recorder such as the Yamaha MIDI Data Filer MDF3 which
will be used to control the Clavinova on playback. By transmitting the Clavinova panel settings and recording them on the MIDI sequence recorder prior to the actual performance data,
the Clavinova will be automatically restored to the same settings when the performance is
played back.
Press the [+/YES] button to transmit the panel/status data. “End” will appear on the LED
display when the data has been successfully transmitted.
• See page 44 for list of the “Panel Data Contents” transmitted by this function.
NOTE
• Panel setting data that is transmitted to an external device can only be reloaded on a model of the
same type. Panel setting data can also be directly transferred to or from instruments of the same
model type.
F7.8/F8.8: Bulk Data Dump...............................................................................................................
This function is used to transmit all data stored in the Recorder memory to a MIDI data
storage device such as the Yamaha MIDI Data Filer MDF3, other sequence recorders, or MIDI
compatible computers.
CLP-880/860/840/820/820S
36
Press the [+/YES] button to begin bulk transmission. “End” will appear on the LED
display when the data has been successfully transmitted.
NOTE
• Bulk data dump will not function when the recorder is in operation.
• Recorder data that is transmitted to an external device can only be reloaded on a model of the same
type. Recorder data can also be directly transferred to or from instruments of the same model type.
• The reload operation cannot be executed when the Recorder is in operation or the Function mode is
engaged.
•
No MIDI note/panel data transmission or data reception occurs during a bulk data dump transmit operation.
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
The Function Mode
F8
F9
CLP-840/820/820S Backup Functions
CLP-880/860 Backup Functions
After selecting “F8.Y” or “F9.Y”, press the [+/YES] button to engage the backup function
sub-mode, then use the FUNCTION [<] and [>] buttons to select the desired backup function, as listed below.
• The backup settings themselves, and the contents of the recorder memory, are always backed up.
NOTE
• Even if the Backup is turned on, factory presets can be recalled at any time (see page 40). The
factory setting list is found on page 42.
Even if backup is turned on via one of the functions described below, the data will only be
retained in memory for about 1 week if the power is not turned on during this time. If the
backup period is exceeded, all settings will be reset to their default values. If you want to
retain the backup settings for longer periods, be sure to turn the power switch on for a few
minutes at least once a week.
F8.1/F9.1: Voice.............................................................................................................................................
Turns backup of the voice functions listed below on or off. Use the [–/NO] and [+/YES]
buttons to turn backup “On” or “OFF”.
The default backup mode is “OFF”.
• Voice (Keyboard, Dual, and Split)
• Dual (ON/OFF, Voice, and Dual Functions for each voice combination)
• Split (ON/OFF, Voice, and Split Functions for each voice combination : CLP-880/860)
• Reverb (ON/OFF, Type, and Depth for each voice)
• Effect (ON/OFF, Type, and Depth for each voice : CLP-880/860/840)
• Variation (for each voice)
• Touch Sensitivity (including the FIXED volume)
• Metronome (Beat, Volume)
• Piano Song Part Cancel Volume
F8.2/F9.2: MIDI................................................................................................................................................
Turns backup of the MIDI functions listed below on or off. Use the [–/NO] and [+/YES]
buttons to turn backup “On” or “OFF”.
The default backup mode is “OFF”.
• Channel (Transmit, Receive) • Local ON/OFF
• Program Change ON/OFF • Control Change ON/OFF
• MIDI Transmit Transpose
F8.3/F9.3: Tuning.........................................................................................................................................
Turns backup of the tuning functions listed below on or off. Use the [–/NO] and [+/YES]
buttons to turn backup “On” or “OFF”.
The default backup mode is “OFF”.
• Transpose • Tuning • Scale (including base note)
F8.4/F9.4: Pedal ............................................................................................................................................
Turns backup of the pedal functions listed below on or off. Use the [–/NO] and [+/YES]
buttons to turn backup “On” or “OFF”.
The default backup mode is “OFF”.
• Left Pedal Mode • Damper Mode (CLP-880/860)
• Soundboard Depth (CLP-880/860)
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
37
HOST SELECT TO HOST
PC-2 PC-1
MIDI
Set to the “Mac”
position.
Connecting to a Personal Computer
Although the Clavinova can be connected to a personal computer via the
MIDI IN/OUT connectors and a MIDI interface, the TO HOST connector and
HOST SELECT switch allow direct connection to Apple Macintosh or IBM-PC/AT
personal computers for sequencing and other music applications without the
need for a separate MIDI interface.
Connecting to an Apple Macintosh Series
Computer................................................................................................................
Connect the TO HOST connector of the Clavinova to the modem or
printer port on your Macintosh, depending on which port your MIDI
Mac
Apple Macintosh
Series Computer
software is using for MIDI data communication, using a standard
Macintosh 8-pin system peripheral cable. Set the HOST SELECT
switch to the “Mac” position.
You may also have to make other MIDI interface settings on the
computer side, depending on the type of software you use (refer to your
software owner’s manual). In any case the clock speed should be set to
1 MHz.
● “Mac” Cable Connections
MINI DIN
8-PIN
• 8-pin system peripheral cable.
• Data transfer rate: 31,250 bps.
NOTE
• When using the [TO HOST] terminal of the Clavinova, first turn the power off on both the Clavinova and the
computer before connecting the cable. After connecting the cable, turn the power of the computer on first, then the
Clavinova.
• When not using the [TO HOST] terminal of the Clavinova, make sure the cable is disconnected from the [TO HOST]
terminal. If the cable is left connected, the Clavinova may not function properly.
•“
HS(
” will appear in the display if the host computer is not turned on, the connecting cable is not properly connected, the HOST SELECT switch is not in the proper position, or the MIDI driver or MIDI application is not active. In
this case, turn the power off on both the Clavinova and the computer, and check the cable connection and the
position of the HOST SELECT switch. Once the connection and HOST SELECT switch position is verified, turn the
power of the computer on first, then the Clavinova, to check if the MIDI driver and MIDI application function properly.
• When the HOST SELECT switch is set to “Mac”, “PC-1”, or “PC-2, no data transfer occurs via the MIDI connectors.
To use the MIDI connectors for connection via a standard MIDI interface, set the HOST SELECT switch to “MIDI”.
2 (HSK i)1
MINI DIN
1 (HSK 0)2
8-PIN
5 (RxD-)3
4 GND4
3 (TxD-)5
8 (RxD+)6
7 (GP i)7
6 (TxD+)8
CLP-880/860/840/820/820S
38
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
HOST SELECT TO HOST
PC-2 PC-1
MIDI
Set to the “PC-2”
position.
Mac
Series Computer
IBM-PC/AT
Connecting to a Personal Computer
Connecting to an IBM-PC/AT Series Computer............
Connect the TO HOST connector of the Clavinova to the RS-232C port
on your IBM computer, using a standard 8-pin MINI DIN → 9-pin D-SUB
cross cable. Set the HOST SELECT switch to the “PC-2” position.
Refer to your software owner’s manual for information on any
settings you might have to make on the computer side.
● “PC-2” Cable Connections
NOTE
• If your system doesn’t work properly with the connections and settings listed above, your software may require
different settings. Check your software operation manual and if it requires a 31,250 bps. data transfer rate, set the
HOST SELECT switch to “PC-1”.
• When using the TO HOST terminal to connect to a personal computer using Windows, a Yamaha MIDI driver must
be installed in the personal computer. The Yamaha MIDI driver can be obtained at Yamaha’s home page on the
World Wide Web, <http://www.yamaha.co.jp/english/xg/>.
● Connector Pin Numbers
MINI DIN 8-PIN
678
34
5
1
2
D-SUB 9-PIN
594837261
MINI DIN
8-PIN
4 5 (GND)
8
8 (CTS)1
D-SUB
7 (RST)2
9-PIN
2 (RxD)3
3 (TxD) 5
• 8-pin mini DIN → 9-pin D-SUB cable.
• Data transfer rate: 38,400 bps.
■ Trademarks
• Apple and Macintosh are trademarks of Apple Computer, Inc.
• IBM-PC/AT is a trademark of International Business Machines Corporation.
• Windows is the registered trademark of Microsoft® Corporation.
All other trademarks are the property of their respective holders.
○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
CLP-880/860/840/820/820S
39
Factory Preset Recall
All dual mode, split mode, reverb, eff ect, touch sensitivity, tuning
POWER
settings, and the settings affected by the Backup Functions can be
restored to their original factory preset values by holding the C7 key
(rightmost key on the keyboard) while turning the [POWER] switch
ON. This also erases all recorder data, and sets all Backup on/off
settings (F8: CLP-840/820/820S, F9: CLP-880/860) to “OFF”.
NOTE
• The factory setting list is found on page 42.
Troubleshooting
If you encounter what appears to be a malfunction, please check the following points before assuming
that your Clavinova is faulty.
1. No Sound When the Power is Turned ON
Is the AC plug properly connected to the Clavinova
and an AC wall outlet? Check the AC connection
carefully. Is the MASTER VOLUME control turned
up to a reasonable listening level?
Also make sure that a pair of headphones is not
plugged into the PHONES jack, and that the Local
Control (page 35) is ON.
2. The Damper Pedal Doesn’t Work
If the damper pedal doesn’t work, or notes are
sustained even when the pedal is not pressed, make
sure that the pedal cord is properly plugged into the
main unit (page 66: CLP-820S, page 60: CLP-860/
840/820, page 52: CLP-880).
3. The Clavinova Reproduces Radio or TV
Sound
This can occur if there is a high-power transmitter in
your vicinity. Contact your Yamaha dealer.
● If “Scn” appears on the display an internal malfunction has occurred. In this case, contact your
Yamaha dealer.
4. Intermittent Static Noise
This is usually due to turning ON or OFF a household appliance or other electronic equipment which
is fed by the same AC mains line as your Clavinova.
5. Interference Appears On Radio or TV Sets
Located Near the Clavinova
The Clavinova contains digital circuitry which can
generate radio-frequency noise. The solution is to
move the Clavinova further away from the affected
equipment, or vice versa.
6. Distorted Sound When the Clavinova is
Connected to An External Amplifier/Speaker
System
If the Clavinova is connected to a stereo system or
instrument amplifier and the sound is distorted,
reduce the volume of the external equipment to a
level at which the distortion ceases.
Options & Expander Modules
● Options
BC-8 Bench
A comfortable bench styled to match your Yamaha
Clavinova.
HPE-160 Stereo Headphones
High-performance lightweight dynamic headphones
with extra-soft ear pads.
KC-883 Key Cover
A convenient way to keep your keyboard clean and
dust-free.
CLP-880/860/840/820/820S
40
(for the CLP-820S only)
○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○
● Expander Modules
DOU-10Disk Orchestra Unit
A range of MIDI recording and playback functions, plus Yamaha DOC software, Disklavier
PianoSoft™, and General MIDI/Standard MIDI File
disk playback capability.
Demo Song List/Verzeichnis der Demo-Songs/
Liste des morceaux de démonstration/
Lista de canciones de demostración
Voice Demo Tune Titles
Voice Name
GRAND PIANO O O O O Fantaisie Impromptu F.F.Chopin
CLASSICAL PIANO O O O – Für Elise L.v.Beethoven
JAZZ PIANO O O – – Original –
ROCK PIANO O O – – Original –
E.PIANO 1* O O O O Original –
E.PIANO 2 O O O – Original –
HARPSICHORD O O O O Gavotte (French Suite) J.S.Bach
STRINGS O O O O Eine Kleine Nachtmusik 3rd Mov. W.A.Mozart
PIPE OPRGAN O O O O Trio Sonata 2 J.S.Bach
CHURCH ORGAN O – – – Noël 3 L.C.d’Aquin
JAZZ ORGAN O – – – Original –
BASS O O – – Original –
* Indicated as E. PIANO on the CLP-820/820S
CLP-880 CLP-860 CLP-840 CLP-820/820S
Title Composer
• Some of the demonstration pieces listed above are short excerpts from the
original compositions. Original songs are all rights reserved (© 1998 by
YAMAHA CORPORATION).
• Bei manchen der oben aufgeführten Demo-Stücke handelt es sich um kurze
Auszüge aus den Originalkompositionen. Originalkompositionen sind
urheberrechtlich geschützt (© 1998 by YAMAHA CORPORATION).
• Certains morceaux de démonstration énumérés ci-dessus sont de courts
extraits des compositions originales. Les morceaux originaux sont protégés par
la loi sur les droits d’auteur (© 1998 par YAMAHA CORPORATION).
• Algunas de las piezas de demostración arriba mencionadas son pasajes cortos
de las composiciones originales. Las canciones originales tienen derechos
reservados (© 1998 por YAMAHA CORPORATION).
CLP-880/860/840/820/820S
41
Factory Setting List/Liste der Vorgabeeinstellungen/
Liste des réglages/Lista de ajustes de fábrica
CLP-880/860 CLP-840/820/820S
Voice GRAND PIANO GRAND PIANO
Dual Mode OFF OFF
Split Mode OFF —
Split Mode Left Voice BASS —
Reverb Type Preset for each voice Preset for each voice
Reverb Depth Preset for each voice Preset for each voice
Effect Type Preset for each voice Preset for each voice
Effect Depth Preset for each voice Preset for each voice
Touch Sensitivity MEDIUM MEDIUM
Volume in the FIXED Mode 64 64
Metronome OFF OFF ——
Metronome Time Signature 0 (no accent) 0 (no accent) F9.1 F8.1
Tempo 120 120 ——
Transpose 0 0 F9.3 F8.3
CLP-880/860 CLP-840/820/820S
Backup Group
F9.1 F8.1
“—”: Not memorized
Function
CLP-880/860 CLP-840 CLP-820/820S
F1 F1 F1 Tuning A3=440Hz
F2.1 F2.1 F2.1 Scale 1 (Equal Temperament) F9.3 F8.3
F2.2 F2.2 F2.2 Base Note C
F3.1 F3.1 F3.1 Dual Balance Preset for each voice combination
F3.2 F3.2 F3.2 Dual Detune Preset for each voice combination
F3.3, F3.4 F3.3, F3.4 F3.3, F3.4 Dual Octave Shift Preset for each voice combination
F3.5, F.3.6 F3.5, F.3.6 — Dual Effect Depth Preset for each voice combination
F4.1 ——Split Point F#2 F9.1 F8.1
F4.2 ——Split Balance Preset for each voice combination
F4.3, F4.4 ——Split Octave Shift Preset for each voice combination
F4.5, F4.6 ——Split Effect Depth Preset for each voice combination
F4.7 ——Damper Range ALL
F5.1 F4 F4 Left Pedal Mode 1 (soft pedal)
F5.2 ——Damper Mode 2 (continuous) F9.4 F8.4
F5.3 ——Soundboard Depth 12
F6 F5 F5 Metronome Volume 10
F7 F6 F6 Piano Song Part Cancel Volume 5
F8.1 F7.1 F7.1 MIDI Transmit Channel 1
F8.2 F7.2 F7.2 MIDI Receive Channel ALL
F8.3 F7.3 F7.3 Local Control ON
F8.4 F7.4 F7.4 Program Change Send & Receive ON
F8.5 F7.5 F7.5 Control Change Send & Receive ON
F8.6 F7.6 F7.6 MIDI Transmit Transpose 0
F9 F8 F8 Backup All OFF
Function Default
Always backed up Always backed up
Backup Group
CLP-880/860 CLP-840/820/820S
F9.1 F8.1
F9.2 F8.2
CLP-880/860/840/820/820S
42
MIDI Data Format/MIDI-Datenformat/
Format des données MIDI/Formato de datos MIDI
If you’re already very familiar with MIDI, or are using a
computer to control your music hardware with computergenerated MIDI messages, the data provided in this section
can help you to control the Clavinova.
Falls Sie bereits mit MIDI vertraut sind oder einen Compu-
ter zur Erzeugung von MIDI-Steuermeldungen für die
Instrumente verwenden, können Sie sich zur Steuerung des
Clavinovas nach den im folgenden Abschnitt aufgeführten
Spezifikationen richten.
1. NOTE ON/OFF
Data format: [9nH] -> [kk] -> [vv]
9nH = Note ON/OFF event (n = channel number)
kk = Note number (Transmit: 09H ~ 78H = A-2 ~ C8 /
Receive: 00H ~ 7FH = C-2 ~ G8)*
vv = Velocity (Key ON = 01H ~ 7FH, Key OFF = 00H)
Data format: [8nH] -> [kk] -> [vv] (reception only)
8nH = Note OFF event (n = channel number)
kk = Note number: 00H ~ 7FH = C-2 ~ G8
vv = Velocity
* If received value exceeds the supported range for the selected
voice, the note is adjusted by the necessary number of octaves.
2. CONTROL CHANGE
Data format: [BnH] -> [cc] -> [vv]
BnH = Control change (n = channel number)
cc = Control number
vv = Data Range
(1) Bank Select
ccH Parameter Data Range (vvH)
00H Bank Select MSB 00H:Normal
20H Bank Select LSB 00H...7FH
Bank selection processing does not occur until receipt of next
Program Change message.
(2) Main Volume (reception only)
ccH Parameter Data Range (vvH)
07H Volume MSB 00H...7FH
(3) Expression
ccH Parameter Data Range (vvH)
0BH Expression MSB 00H...7FH
(4) Damper
ccH Parameter Data Range (vvH)
40H Damper MSB 00H...7FH
(5) Sostenuto
ccH Parameter Data Range (vvH)
42H Sostenuto 00H-3FH:off, 40H-7FH:on
(6) Soft Pedal
ccH Parameter Data Range (vvH)
43H Soft Pedal 00H-3FH:off, 40H-7FH:on
(7) Effect1 Depth ( Reverb Send Level )
ccH Parameter Data Range (vvH)
5BH Effect1 Depth 00H...7FH
Adjusts the reverb send level.
(8) Effect4 Depth ( Variation Effect Send Level )
(CLP-880/860/840)
ccH Parameter Data Range (vvH)
5EH Effect4 Depth 00H...7FH
Si vous êtes très familier avec l’interface MIDI ou si vous
utilisez un ordinateur pour commander votre matériel de
musique au moyen de messages MIDI générés par
ordinateur, les données suivantes vous seront utiles et vous
aideront à commander le Clavinova.
SI usted está ya familiarizado con MIDI, o si emplea una
computadora para controlar sus aparatos musicales con
mensajes MIDI generados por computadora, los datos
proporcionados en esta sección le ayudarán a controlar la
Clavinova.
3 MODE MESSAGES
Data format: [BnH] -> [cc] -> [vv]
BnH = Control event (n = channel number)
cc = Control number
vv = Data Range
(1) All Sound Off
ccH Parameter Data Range (vvH)
78H All Sound Off 00H
Switches off all sound from the channel. Does not reset Note On
and Hold On conditions established by Channel Messages.
(2) Reset All Controllers
ccH Parameter Data Range (vvH)
79H
Reset All Controllers
Resets controllers as follows.
Controller Value
Expression 127 (max)
Damper Pedal 0 (off)
Sostenuto 0 (off)
Soft Pedal 0 (off)
(3) Local Control (reception only)
ccH Parameter Data Range (vvH)
7AH Local Control 00H (off), 7FH (on)
(4) All Notes Off
ccH Parameter Data Range (vvH)
7BH All Notes Off 00H
Switches OFF all the notes that are currently ON on the specified
channel. Any notes being held by the damper or sostenuto pedal
will continue to sound until the pedal is released.
(5) Omni Off (reception only)
ccH Parameter Data Range (vvH)
7CH Omni Off 00H
Same processing as for All Notes Off.
(6) Omni On (reception only)
ccH Parameter Data Range (vvH)
7DH Omni On 00H
Same processing as for All Notes Off.
(7) Mono (reception only)
ccH Parameter Data Range (vvH)
7EH Mono 00H
Same processing as for All Sound Off.
(8) Poly (reception only)
ccH Parameter Data Range (vvH)
7FH Poly 00H
Same processing as for All Sound Off.
• When control change reception is turned OFF in the Function
mode, control change data will not be transmitted or received
except for Bank Select and Mode messages.
• Local on/off, OMNI on/off are not transmitted. (The appropriate
note off number is supplied with “All Note Off” transmission).
• When a voice bank MSB/LSB is received, the number is stored
in the internal buffer regardless of the received order, then the
stored value is used to select the appropriate voice when a
program change message is received.
• The Multi-timbre and Poly modes are always active. No change
occurs when OMNI ON, OMNI OFF, MONO, or POLY mode
messages are received.
00H
CLP-880/860/840/820/820S
43
MIDI Data Format/MIDI-Datenformat/Format des données MIDI/Formato de datos MIDI
4. PROGRAM CHANGE
Data format: [CnH] -> [ppH]
CnH = Program event (n = channel number)
ppH = Program change number
CLP-880 CLP-860
Normal Voice
GRAND PIANO 0 112 0 0 113 0 0 112 0 0 113 0
CLASSICAL PIANO 0 114 0 0 115 0 0 114 0 0 115 0
JAZZ PIANO 0 112 1 0 113 1 0 112 1 0 113 1
ROCK PIANO 0 114 1 0 115 1 0 114 1 0 115 1
E.PIANO 1 0 112 5 0 112 88 0 112 5 0 112 88
E.PIANO 2 0 112 4 0 118 4 0 112 4 0 118 4
HARPSICHORD 0 112 6 0 115 6 0 112 6 0 115 6
STRINGS 0 112 48 0 113 49 0 112 48 0 113 49
PIPE ORGAN 0 112 19 0 113 19 0 112 19 0 113 19
CHURCH ORGAN 0 115 19 0 114 19
JAZZ ORGAN 0 112 16 0 113 16
BASS 0 112 32 0 114 32 0 112 32 0 114 32
GRAND PIANO 0 112 0 0 113 0 112 0 0 0 113 0
CLSSICAL PIANO 0 114 0 0 115 0
E.PIANO 1* 0 112 5 0 112 88 112 5 5 0 112 88
E.PIANO 2 0 112 4 0 118 4
HARPSICHORD 0 112 6 0 115 6 112 6 6 0 115 6
STRINGS 0 112 48 0 113 49 112 48 48 0 113 49
PIPE ORGAN 0 112 19 0 113 19 112 19 19 0 113 19
* Indicated as E. PIANO on the CLP-820/820S
MSB LSB
Normal Voice
MSB LSB
VARIATION Voice
P.C.#
MSB LSB
CLP-840 CLP-820/820S
VARIATION Voice
P.C.#
MSB LSB
P.C.#=Program Change number
Normal Voice VARIATION Voice
P.C.#
MSB LSB
P.C.#
MSB LSB
Normal Voice VARIATION Voice
P.C.#
MSB LSB
P.C.#
MSB LSB
• When program change reception is turned OFF in the Function
mode, no program change data is transmitted or received.
Also, Bank MSB/LSB is not transmitted or received.
5. SYSTEM REALTIME MESSAGES
[rrH]
F8H: Timing clock
FAH: Start
FCH: Stop
FEH: Active sensing
Data Transmission Reception
F8H Transmitted every Received as 96-clock tempo timing
96 clocks when MIDI clock is set to External
FAH Recorder start Recorder start
Not received when the MIDI clock
is set to Internal.
FCH Recorder stop Recorder stop
Not received when the MIDI clock
is set to Internal.
FEH Transmitted every If a signal is not received via MIDI
200 milliseconds for more than 400 milliseconds, the
same processing will take place for
All Sound Off, All Notes Off and
Reset All Controllers as when those
signals are received.
• Caution: If an error occurs during MIDI reception, the Damper, Sostenuto,
and Soft effects for all channels are turned off and an All Note Off occurs.
6. SYSTEM EXCLUSIVE MESSAGES
(Yamaha MIDI Format)
Panel Data Transmit
Data format: [F0H] -> [43H] -> [0nH] -> [7CH] -> ... ->
[F7H]
F0H, 43H, 0nH, 7CH (n: channel number)
00H, 2CH (
43H, 4CH, 20H, 20H (CL)
43H, 4CH, 50H, 27H, 39H, 38H (CLP-880/860/840/820/820S)
30H, 30H (version x, y)
[PANEL DATA]
[CHECK SUM (1byte)] = 0-(43H+4CH+20H+......+Data end)
F7H
data length
)
P.C.#
P.C.#
• Panel Data Contents
(1) 1'st Voice OO O
CLP-880/860
(2) Dual On/Off OO O
(3) Dual Voice OO O
(4) Dual Balance OO O
(5) Dual Detune OO O
(6) Dual Voice1 Octave OO O
(7) Dual Voice2 Octave OO O
(8) Dual Voice1 Effect Depth OO O
(9) Dual Voice2 Effect Depth OO O
(10) Split On/Off OX X
(11) Split Voice OX X
(12) Split Point OX X
(13) Split Balance OX X
(14) Split Voice1 Octave OX X
(15) Split Voice2 Octave OX X
(16) Split Voice1 Effect Depth OX X
(17) Split Voice2 Effect Depth OX X
(18) Split Dumper Mode OX X
(19) Reverb Type 1 OO O
(20) Reverb Type 2 OO O
(21) Reverb Depth1 OO O
(22) Reverb Depth2 OO O
(23) Effect Type 1 OO X
(24) Effect Type 2 OO X
(25) Effect Depth OO X
(26) Variation 1 On/Off OO O
(27) Variation 2 On/Off OO O
(28) Touch Sensitivity OO O
(29) Fixed Data OO O
(30) Left Pedal Function OO O
(31) Absolute tempo low byte OO O
(32) Absolute tempo high byte OO O
CLP-840
CLP-820/820S
• “X” indicates no affect.
• Panel data send requests cannot be received.
7. SYSTEM EXCLUSIVE MESSAGES
(Universal System Exclusive)
(1) Universal Realtime Message
Data format: [F0H] -> [7FH] -> [XnH] -> [04H] -> [01H] ->
[llH] -> [mmH] -> [F7H]
MIDI Master Volume
• Simultaneously changes the volume of all channels.
• When a MIDI master volume message is received, the volume
only has affect on the MIDI receive channel, not the panel
master volume.
F0H = Exclusive status
7FH = Universal Realtime
7FH = ID of target device
04H = Sub-ID #1=Device Control Message
01H = Sub-ID #2=Master Volume
llH = Volume LSB
mmH = Volume MSB
F7H = End of Exclusive
or
F0H = Exclusive status
7FH = Universal Realtime
XnH = When n is received n=0~F, whichever is received.
X = don’t care
04H = Sub-ID #1=Device Control Message
01H = Sub-ID #2=Master Volume
llH = Volume LSB
mmH = Volume MSB
F7H = End of Exclusive
CLP-880/860/840/820/820S
44
(2) Universal Non-Realtime Message (GM 0n)
General MIDI Mode On
Data format: [F0H] -> [7EH] -> [XnH] -> [09H] -> [01H] ->
[F7H]
F0H = Exclusive status
7EH = Universal Non-Realtime
7FH = ID of target device
09H = Sub-ID #1=General MIDI Message
01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
or
F0H = Exclusive status
7EH = Universal Non-Realtime
XnH = When received, n=0~F.
X = don’t care
09H = Sub-ID #1=General MIDI Message
01H = Sub-ID #2=General MIDI On
F7H = End of Exclusive
When the General MIDI mode ON message is received, the MIDI
system will be reset to its default settings.
This message requires approximately 50ms to execute, so sufficient time should be allowed before the next message is sent.
8. SYSTEM EXCLUSIVE MESSAGES (XG Standard)
(1) XG Native Parameter Change
Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->
[mmH] -> [llH] -> [ddH] -> [F7H]
F0H = Exclusive status
43H = YAMAHA ID
1nH = When received, n=0~F.
When transmitted, n=0.
4CH = Model ID of XG
hhH = Address High
mmH = Address Mid
llH = Address Low
ddH = Data
|
F7H = End of Exclusive
Data size must match parameter size (2 or 4 bytes).
When the XG System On message is received, the MIDI system
will be reset to its default settings.
The message requires approximately 50ms to execute, so sufficient time should be allowed before the next message is sent.
(2) XG Native Bulk Data (reception only)
Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->
[bbH] -> [hhH] -> [mmH] -> [llH] ->
[ddH] ->...-> [ccH] -> [F7H]
F0H Exclusive status
43H YAMAHA ID
0nH When received, n=0~F.
When transmitted, n=0.
4CH Model ID of XG
aaH ByteCount
bbH ByteCount
hhH Address High
mmH Address Mid
llH Address Low
ddH Data
| |
| |
ccH Check sum
F7H End of Exclusive
• Receipt of the XG SYSTEM ON message causes reinitialization
of relevant parameters and Control Change values. Allow sufficient time for processing to execute (about 50 msec) before
sending the Clavinova another message.
• XG Native Parameter Change message may contain two or four
bytes of parameter data (depending on the parameter size).
• For information about the Address and Byte Count values, refer
to Table 1 below. Note that the table’s Total Size value gives the
size of a bulk block. Only the top address of the block (00H, 00H,
00H) is valid as a bulk data address.
9. SYSTEM EXCLUSIVE MESSAGES
(Clavinova MIDI Format)
Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [nnH] ->
[F7H]
F0H = Exclusive status
43H = Yamaha ID
73H = Clavinova ID
xxH = Product ID (CLP-880/860/840/820/820S common ID:
50H or CLP common ID: 01H)
nnH = Substatus
nn Control
02H Internal MIDI clock
03H External MIDI clock
06H Bulk Data (the bulk data follows 06H)
F7H = End of Exclusive
* When nn=02H or 03H, Clavinova common ID (01H) is
recognized as well as 50H.
BULK DUMP FORMAT
F0H, 43H, 73H
xxH =Product ID (CLP-880: 56H, CLP-860:
06H =Bulk ID
05H =Sequence data
0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH, 0nH =Data length
[BULK DATA] =
[CHECK SUM (1byte)] = 0-sum (BULK DATA)
F7H = End of Exclusive
54H, CLP-840: 53H, CLP-820/820S:
52H)
10. SYSTEM EXCLUSIVE MESSAGES (Special Control)
Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [11H] ->
[0nH] -> [ccH] -> [vvH] -> [F7H]
F0H = Exclusive status
43H = Yamaha ID
73H = Clavinova ID
50H =
11H = Clavinova special control
0nH = Control MIDI change (n=channel number)
cc = Control number
vv = Value
F7H = End of Exclusive
Control 0n ccH vvH
Split Point Always 00H 14H 14H :
Metronome Always 00H 1BH 00H : off
Damper Level ch: 00H-0FH 3DH (Sets the Damper Level
Channel Detune ch: 00H-0FH 43H (Sets the Detune value for
Voice Reserve ch: 00H-0FH 45H 00H : Reserve off
* When Volume, Expression is received for Reserve On, they will
be effective from the next Key On. Reserve Off is normal.
CLP-880/860/840/820/820S common ID
Split Key Number
(CLP-880/860)
01H : –
02H : 2/4
03H : 3/4
04H : 4/4
06H : 6/4
7FH : No accent
for each channel)
00H-7FH
each channel)
00H-7FH
7FH : on*
11. SYSTEM EXCLUSIVE MESSAGES (Others)
Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] ->
[00H] -> [00H] -> [mmH] -> [llH] -> [ccH] ->
[F7H]
Master Tuning (XG and last message priority) simultaneously
changes the pitch of all channels.
F0H = Exclusive Status
43H = Yamaha ID
1nH = Transmission from n=CLP is always 0. 0-F is received.
27H = Model ID of TG100
30H = Sub ID
00H =
00H =
mmH = Master Tune MSB
llH = Master Tune LSB
ccH = don’t care (under 7FH)
F7H = End of Exclusive
CLP-880/860/840/820/820S
45
MIDI Data Format/MIDI-Datenformat/Format des données MIDI/Formato de datos MIDI
<Table 1>
MIDI Parameter Change table ( SYSTEM )
Address (H) Size (H) Data (H) Parameter Description Default value (H)
00 00 00 4
01 1st bit 3 - 0 → bit 15 - 12 400
02 2nd bit 3 - 0 → bit 11 - 8
03 3rd bit 3 - 0 → bit 7 - 4
04 1 00 - 7F MASTER VOLUME 0 - 127 7F
05 1 ——
06 1 34 - 4C(*2) TRANSPOSE -12 - +12[semitones] 40
7E 00 XG SYSTEM ON 00=XG sytem ON
7F 00 RESET ALL PARAMETERS 00=ON (receive only)
TOTAL SIZE 07
*1: Values lower than 020CH select -50 cents. Values higher than 05F4H select +50 cents.
*2: Values from 28H through 33H are interpreted as -12 through -1. Values from 4DH through 58H are interpreted as +1 through +12.
<Table 2>
MIDI Parameter Change table ( EFFECT 1)
Refer to the “Effect MIDI Map” for a complete list of Reverb, Chorus and Variation type numbers.
Address (H) Size (H) Data (H) Parameter Description Default value (H)
02 01 00 2 00-7F REVERB TYPE MSB Refer to Effect MIDI Map 01(=HALL1)
02 01 40 2 00-7F VARIATION TYPE MSB Refer to Effect MIDI Map 00(=Effect off) (CLP-880/860/840)
• “VARIATION” refers to the EFFECT on the panel.
<Table 3>
MIDI Parameter Change table ( MULTI PART )
Address (H) Size (H) Data (H) Parameter Description Default value (H)
08 nn 11 1 00 - 7F DRY LEVEL 0 - 127 7F (CLP-880/860/840)
nn = Part Number
020C - 05F4(*1)
00-7F REVERB TYPE LSB 00 : basic type 00
00-7F VARIATION TYPE LSB 00 : basic type 00 (CLP-880/860/840)
MASTER TUNE -50 - +50[cent] 00 04 00 00
4th bit 3 - 0 → bit 3 - 0
● Effect MIDI Map
REVERB
ROOM 02H 10H
HALL 1 01H 10H
HALL 2 01H 11H
STAGE 03H 10H
EFFECT (CLP-880/860/840)
CHORUS 42H 10H
SYMPHONIC 44H 10H
TREMOLO 46H 10H
DELAY 05H 10H
MSB LSB
MSB LSB
CLP-880/860/840/820/820S
46
YAMAHA [Clavinova] Date: 1/21, 1998
Model: CLP-880/860/840/820/820S
Function Transmitted Recognized Remarks
Basic Default 1 1
Channel Changed 1~16 1~16
Default 3 1 *1 Poly Mode only
Mode Messages XX
Altered ***************** X
Note 9~120 0~127
Number : True voice ***************** 21~108
Velocity Note on O 9nH, v=1~127 O v=1~127
Note off X 9nH, v=0 X
After key’s XX
Touch Ch’s XX
Pitch Bender XX
MIDI Implementation Chart Version: 1.1
Control Change
0, 32 OOBank Select
07 XOVolume
11 XOExpression
64 OODamper
66 OOSostenuto
67 OOSoft pedal
91 OOReverb Depth
94 OOEffect Depth
120 XOAll sounds off
121 XOReset All Controllers
Program OO
Change : True # *****************
System Exclusive OO
System : Song Position XX
: Song Select XX
Common : Tune XX
System : Clock OO
Real Time: Commands OO
Aux : Local ON/OFF XO
: All Notes Off OO (123~127)
Messages: Active Sense OO
: Reset XX
Notes : *1 = Recieve Mode is always multi timbre and Poly mode.
Mode 1: OMNI ON, POLY Mode 2: OMNI ON, MONO O: Yes
Mode 3: OMNI OFF, POLY Mode 4: OMNI OFF, MONO X: No
CLP-880/860/840/820/820S
47
1
A
5 x 40 mm long gold screws
x 6 1
E
6 x 20 mm round-head screws
x 4 2
B
F
B
4 x 12 mm round-head screws
D
C
Bundled pedal cord inside
● Cord holders x 2 ● AC power cord
◆ B and C are already attached on the CLP-880PE. The 5 x 40 mm long gold screws are not supplied with the CLP-880PE.
C
4 x 20 mm tapping screws
6 x 16 mm flat-head screws
CLP-880: Keyboard Stand Assembly
• Be careful not to confuse parts, and be sure to install all parts in the
correct direction. Please assemble in accordance with the sequence
given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated above. Use of
incorrect screws can cause damage.
• Be sure to tighten up all screws upon completing assembly of each
unit.
• To disassemble, reverse the assembly sequence given below.
x 8 3
x 4 4
x 4 5
CLP-880/860/840/820/820S
48
Have a Phillips-head (+) screwdriver ready.
Open the box and remove all the parts.
Z
On opening the box you should find the parts shown in the
illustration. Check to make sure that all the required parts are
provided.
2 3
● If applicable, align the
cut corner of the bracket
with the corresponding
cutouts on the feet.
B
◆ It is not necessary to perform this procedure on the CLP-880PE.
B
5 x 40 mm long gold screws 1
6 x 20 mm round-head screws 2
B
B
D
Assemble the side panels (B) and feet (C).
X
Secure the feet (C) to the side panels (B) with the 5 x 40
millimeter long gold-colored screws 1 (3 each).
Depending on the unit type, the feet (C) may or may not have
cutouts. If the feet have cutouts, make sure that the cutouts on the
feet face the bracket side of the side panels.
◆ It is not necessary to perform this procedure on the CLP-880PE.
Attach the side panels (B) to the pedal box
C
(D).
Before installing the pedal box, untie and straighten out the
bundled cord attached to the bottom of the pedal box.
Place the pedal box on top of the brackets attached to the side
panels (B), and attach using the four 6 x 20 millimeter round-head
screws 2 — two screws on each side. Make sure the pedals extend
in the same direction as the feet.
CLP-880/860/840/820/820S
49
4 5
B
15 cm
B
E
4 x 12 mm round-head screws 3
15 cm
10 cm
10 cm
● Be sure to place your hands at least 10 centimeters from
either end of the main unit and position the unit so that it
rests 15 centimeters from the front end of the side panels.
Attach the front panel (E).
V
The front panel attaches to the front end of the pedal box and
side panels. Fit the front panel into position and eliminate any
gaps between the front and side panels. Align the
each six brackets and attach the front panel using the six 4 x 12
millimeter round-head screws 3.
Install the main unit (A).
B
Rest the rear edge of the main unit (A) on the front edges of
the cutouts in the side panels (B), then slide the main unit backward firmly until it stops (
the main unit side panels and the stand, as shown in illustration
“a”). WATCH YOUR FINGERS WHILE DOING THIS!!
There is slight horizontal play between the main unit and side
panels, so center the main unit, as shown in illustration “b”, then
use the four 6 x 16 millimeter flat-head screws 5 to attach the
main unit. Two screws can be attached from the front side and
two screws from the rear.
• Do not hold the keyboard in any position other than the position
shown in the above illustration.
• Fingers can become pinched between the main unit and the front or
side panels, be extra careful so as not to drop the main unit.
so that there is no clearance between
small hole in
CLP-880/860/840/820/820S
50
(a)
(b)
6 x 16 mm flat-head screws 5
6
B
A
● Before connecting the speaker cord, remove the two tapes attaching the speaker cord to the speaker box.
Connect the speaker cord.
N
The speaker cord from the speaker box must be plugged into
the corresponding connector in the main unit. The plug only
goes in one way (the lug on the connector should face the rear of
the main unit, as shown in the illustration), so don’t try to force
it in the wrong way around.
CLP-880/860/840/820/820S
51
7
F
B
4 x 12 mm round-head screws 3
F
Attach the rear panel (F).
M
With the rear panel slightly angled as shown in the illustration,
lower it onto the feet’s protruding edge at the rear of the pedal
box. Then, secure the top of the rear panel to the side panel
brackets using two 4 x 12 mm round-head screws 3. Finally,
secure the bottom of the rear panel to the pedal box using four 4 x
20 mm tapping screws 4.
4 x 20 mm tapping screws 4
CLP-880/860/840/820/820S
52
8 9
Cord holder
Connect the pedal cord.
<
The pedal cord from the pedal box must be plugged into the
PEDAL connector on the rear of the main unit. Once connected,
attach the cord holders to the rear panel as shown, then clip the
cord into the holders.
● A voltage selector is provided in some areas.
240
110
220
127
Voltage Selector
>
Before connecting the AC power cord, check the setting of the
voltage selector which is provided in some areas. To set the
selector for 110V, 127V, 220V or 240V main voltages, use a
“minus” screwdriver to rotate the selector dial so that the correct
voltage for your region appears next to the pointer on the panel.
The voltage selector is set at 240V when the unit is initially
shipped.
After the proper voltage has been selected connect the AC
power cord. A plug adaptor may be also provided in some areas
to match the pin configuration of the AC wall outlets in your
area.
CLP-880/860/840/820/820S
53
10
D
Set the adjuster.
?
For stability, an adjuster is provided on the bottom of the
pedal box (D). Rotate the adjuster until it comes in firm contact
with the floor surface. The adjuster ensures stable pedal operation
and facilitates pedal effect control. If the adjuster is not in firm
contact with the floor surface, distorted sound may result.
CLP-880/860/840/820/820S
54
• When moving the instrument after assembly, always hold
the lower surface of the main unit, NEVER the top portion or
keyboard cover. Improper handling can result in damage to
the instrument or personal injury.
■ After completing the assembly, please
check the following.
• Are there any parts left over?
➔ Review the assembly procedure and correct any
errors.
• Is the Clavinova clear of doors and other movable fixtures?
➔ Move the Clavinova to an appropriate location.
• Does the Clavinova make a rattling noise when you
shake it?
➔ Tighten all screws.
• Does the pedal box rattle or give way when you step on
the pedals?
➔ Turn the adjuster so that it is set firmly against the
floor.
• Are the pedal and power cords inserted securely into the
sockets?
➔ Check the connection.
• If the main unit creaks or is otherwise unsteady when
you play on the keyboard, refer to the assembly diagrams and retighten all screws.
CLP-880/860/840/820/820S
55
1
5 x 40 mm long gold screws
x 6 1
A
6 x 20 mm round-head screws
DD
B
4 x 12 mm round-head screws
C
EE
Bundled pedal cord inside
● Cord holders x 2 ● AC power cord
4 x 20 mm tapping screws
6 x 16 mm flat-head screws
CLP-860/840/820: Keyboard Stand Assembly
The CLP-860/840/820 all require the same assembly
procedures. Illustrations use the CLP-860 for reference.
x 4 2
x 2 3
x 4 4
x 4 5
• Be careful not to confuse parts, and be sure to install all parts in the
correct direction. Please assemble in accordance with the sequence
given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated above. Use of
incorrect screws can cause damage.
• Be sure to tighten up all screws upon completing assembly of each
unit.
• To disassemble, reverse the assembly sequence given below.
Have a Phillips-head (+) screwdriver ready.
Open the box and remove all the parts.
Z
On opening the box you should find the parts shown in the
illustration. Check to make sure that all the required parts are
provided.
CLP-880/860/840/820/820S
56
2 3
● If applicable, align the
cut corner of the
bracket with the corresponding cutouts on
the feet.
D
6 x 20 mm round-head screws 2
D
D
D
C
5 x 40 mm long gold screws 1
Assemble the side panels (D) and feet (E).
X
Secure the feet (E) to the side panels (D) with the 5 x 40
millimeter long gold-colored screws 1 (3 each).
Depending on the unit type, the feet (E) may or may not have
cutouts. If the feet have cutouts, make sure that the cutouts on the
feet face the bracket side of the side panels.
Attach the side panels (D) to the pedal box
C
(C).
Before installing the pedal box, untie and straighten out the
bundled cord attached to the bottom of the pedal box. Don’t discard the vinyl tie, you’ll need it later in step N.
Place the pedal box on top of the brackets attached to the side
panels (D), and attach using the four 6 x 20 millimeter roundhead screws 2 — two screws on each side. Make sure the pedals
extend in the same direction as the feet.
CLP-880/860/840/820/820S
57
4
4 x 12 mm round-head screws 3
B
B
D
4 x 20 mm tapping screws 4
Attach the rear panel (B).
V
With the rear panel slightly angled as shown in the illustration,
lower it onto the feet’s protruding edge at the rear of the pedal
box. Then, while eliminating any gaps between the rear and side
panels, secure the top of the rear panel to the side panel brackets
using two 4 x 12 mm round-head screws 3. Finally, secure the
bottom of the rear panel to the pedal box using four 4 x 20 mm
tapping screws 4.
CLP-880/860/840/820/820S
58
5
6 x 16 mm flat-head screws 5
10 cm
● Be sure to place your
hands at least 10
centimeters from either
end of the main unit
when positioning it.
A
10 cm
D
Install the main unit (A).
B
Place the main unit (A) on the side panels (D) with the screws
on its bottom panel (toward the rear of the main unit) just behind
the grooves in the brackets located at the top of the side panels.
Then slide the main unit forward until it stops. WATCH YOUR
FINGERS WHEN DOING THIS!!
Align the holes on the bottom panel of the main unit with the
holes in the brackets on the side panels
to produce equal clearance on the left and right sides, as shown in
the illustration), then use the four 6 x 16 millimeter flat-head
screws 5 to attach the main unit. Two screws can be attached
from the front side and two screws from the rear.
(also center the main unit
A
• Do not hold the keyboard in any position other than the position
shown in the above illustration.
• Fingers can become pinched between the main unit and the rear or
side panels, be extra careful so as not to drop the main unit.
CLP-880/860/840/820/820S
59
6 7
Cord holder
● A voltage selector is provided in some areas.
● Use the vinyl tie that was removed from the bundled pedal cord in
step C to tie up any slack in the pedal cord.
Connect the pedal cord.
N
The pedal cord from the pedal box must be plugged into the
PEDAL connector on the rear of the main unit. Once connected, attach the cord holders to the rear panel as shown, then
clip the cord into the holders.
240
110
220
127
Voltage Selector
M
Before connecting the AC power cord, check the setting of
the voltage selector which is provided in some areas. To set the
selector for 110V, 127V, 220V or 240V main voltages, use a
“minus” screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the
panel. The voltage selector is set at 240V when the unit is
initially shipped.
After the proper voltage has been selected connect the AC
power cord. A plug adaptor may be also provided in some
areas to match the pin configuration of the AC wall outlets in
your area.
CLP-880/860/840/820/820S
60
8
C
• When moving the instrument after assembly, always hold the lower surface of
the main unit, NEVER the top portion or
keyboard cover. Improper handling can
result in damage to the instrument or
personal injury.
Set the adjuster.
<
For stability, an adjuster is provided on the bottom of the
pedal box (C). Rotate the adjuster until it comes in firm contact
with the floor surface. The adjuster ensures stable pedal operation
and facilitates pedal effect control. If the adjuster is not in firm
contact with the floor surface, distorted sound may result.
■ After completing the assembly, please
check the following.
• Are there any parts left over?
➔ Review the assembly procedure and correct any errors.
• Is the Clavinova clear of doors and other movable fixtures?
➔ Move the Clavinova to an appropriate location.
• Does the Clavinova make a rattling noise when you shake it?
➔ Tighten all screws.
• Does the pedal box rattle or give way when you step on the pedals?
➔ Turn the adjuster so that it is set firmly against the floor.
• Are the pedal and power cords inserted securely into the sockets?
➔ Check the connection.
• If the main unit creaks or is otherwise unsteady when you play on
the keyboard, refer to the assembly diagrams and retighten all
screws.
CLP-880/860/840/820/820S
61
1
A
5 x 40 mm long gold screws
DD
B
6 x 20 mm round-head screws
C
EE
Bundled pedal cord inside
6 x 16 mm flat-head screws
● AC power cord
CLP-820S:
x 6 1
x 4 2
x 8 3
Keyboard Stand Assembly
• Be careful not to confuse parts, and be sure to install all parts in the
correct direction. Please assemble in accordance with the sequence
given below.
• Assembly should be carried out by at least two persons.
• Be sure to use the correct screw size, as indicated above. Use of
incorrect screws can cause damage.
• Be sure to tighten up all screws upon completing assembly of each
unit.
• To disassemble, reverse the assembly sequence given below.
Have a Phillips-head (+) screwdriver ready.
Open the box and remove all the parts.
Z
On opening the box you should find the parts shown in the
illustration. Check to make sure that all the required parts are
provided.
CLP-880/860/840/820/820S
62
2 3
● If applicable, align the
cut corner of the
bracket with the corresponding cutouts on
the feet.
D
6 x 20 mm round-head screws 2
D
D
D
C
5 x 40 mm long gold screws 1
Assemble the side panels (D) and feet (E).
X
Secure the feet (E) to the side panels (D) with the 5 x 40
millimeter long gold-colored screws 1 (3 each).
Depending on the unit type, the feet (E) may or may not have
cutouts. If the feet have cutouts, make sure that the cutouts on the
feet face the bracket side of the side panels.
Attach the side panels (D) to the pedal box
C
(C).
Before installing the pedal box, untie and straighten out the
bundled cord attached to the bottom of the pedal box. Don’t discard the vinyl tie, you’ll need it later in step N.
Place the pedal box on top of the brackets attached to the side
panels (D), and attach using the four 6 x 20 millimeter roundhead screws 2 — two screws on each side. Make sure the pedals
extend in the same direction as the feet.
CLP-880/860/840/820/820S
63
4
B
D
6 x 16 mm flat-head screws 3
Attach the center panel (B) to the side pan-
V
els (D).
The center panel (B) is installed between the side panels (D)
with the brackets on each end toward the rear of the stand assembly. Place the square holes in the center-panel brackets over the
lugs extending from the side panels, then slide down. Each side
of the center panel is attached using two 6 x 16 flat-head screws
3.
CLP-880/860/840/820/820S
64
5
● Be sure to place your hands at
least 10 centimeters from either
end of the main unit when positioning it.
10 cm
10 cm
6 x 16 mm flat-head screws 3
Install the main unit (A).
B
Place the main unit (A) on the side panels (D) with the screws
on its bottom panel (toward the rear of the main unit) just behind
the grooves in the brackets located at the top of the side panels.
Then slide the main unit forward until it stops. WATCH YOUR
FINGERS WHEN DOING THIS!!
Align the holes on the bottom panel of the main unit with the
holes in the brackets on the side panels
to produce equal clearance on the left and right sides, as shown in
the illustration), then use the four 6 x 16 millimeter flat-head
screws 3 to attach the main unit. Two screws can be attached
from the front side and two screws from the rear.
(also center the main unit
A
A
D
A
D
• Do not hold the keyboard in any position other than the position
shown in the above illustration.
• Fingers can become pinched between the main unit and the side
panels, be extra careful so as not to drop the main unit.
CLP-880/860/840/820/820S
65
6 7
Cord holder
● A voltage selector is provided in some areas.
● Use the vinyl tie that was removed from the bundled pedal cord in
step C to tie up any slack in the pedal cord.
Connect the pedal cord.
N
Pass the pedal cord through the two cord holders on the side
panel. Plug the free end of the cord into the PEDAL connector
on the rear of the main unit.
Voltage Selector
M
Before connecting the AC power cord, check the setting of
the voltage selector which is provided in some areas. To set the
selector for 110V, 127V, 220V or 240V main voltages, use a
“minus” screwdriver to rotate the selector dial so that the correct voltage for your region appears next to the pointer on the
panel. The voltage selector is set at 240V when the unit is
initially shipped.
After the proper voltage has been selected connect the AC
power cord. A plug adaptor may be also provided in some
areas to match the pin configuration of the AC wall outlets in
your area.
240
110
220
127
CLP-880/860/840/820/820S
66
8
C
• When moving the instrument after assembly, always hold the lower surface of
the main unit, NEVER the top portion.
Improper handling can result in damage
to the instrument or personal injury.
Set the adjuster.
<
For stability, an adjuster is provided on the bottom of the
pedal box (C). Rotate the adjuster until it comes in firm contact
with the floor surface. The adjuster ensures stable pedal operation
and facilitates pedal effect control. If the adjuster is not in firm
contact with the floor surface, distorted sound may result.
■ After completing the assembly, please
check the following.
• Are there any parts left over?
➔ Review the assembly procedure and correct any errors.
• Is the Clavinova clear of doors and other movable fixtures?
➔ Move the Clavinova to an appropriate location.
• Does the Clavinova make a rattling noise when you shake it?
➔ Tighten all screws.
• Does the pedal box rattle or give way when you step on the pedals?
➔ Turn the adjuster so that it is set firmly against the floor.
• Are the pedal and power cords inserted securely into the sockets?
➔ Check the connection.
• If the main unit creaks or is otherwise unsteady when you play on
the keyboard, refer to the assembly diagrams and retighten all
screws.
CLP-880/860/840/820/820S
67
Specifications/Technische Daten/Caractéristiques techniques/Especificaciones
CLP-880 CLP-860 CLP-840 CLP-820 CLP-820S
KEYBOARD
POLYPHONY
VOICE SELECTORS
REVERB
EFFECT
TOUCH SENSITIVITY
RECORDER
PEDAL CONTROLS
OTHER CONTROLS
JACKS/CONNECTORS
INPUT & OUTPUT
LEVEL/IMPEDANCE
MAIN AMPLIFIERS
SPEAKERS
Music stand down
DIMENTIONS
(W x D x H)
Music stand up
WEIGHT
88 KEYS (A-1 ~ C7)
64 NOTES MAX. 32 NOTES MAX.
12 voices + 10 voices + 7 voices + 5 voices +
Variation for each voice Variation for each voice Variation for each voice Variation for each voice
ROOM, HALL 1, HALL 2, STAGE
CHORUS, SYMPHONIC, TREMOLO, DELAY —
HARD, MEDIUM, SOFT, FIXED
1, 2, START/STOP, REC
SOFT, SOSTENUTO, DAMPER SOFT/SOSTENUTO,
DAMPER
MASTER VOLUME, BRILLIANCE (CLP-880/860/840), DEMO, TRANSPOSE, SPLIT (CLP-880/860),
METRONOME, TEMPO [s]/[t], FUNCTION, PIANO SONG, SONG SELECT [s]/[t], LED Display
PHONES x 2, AUX OUT R & L/L+R, AUX IN R & L/L+R,
MIDI IN/OUT/THRU, HOST SELECT, TO HOST, PEDAL
AUX OUT: Output impedance 600 Ω
AUX IN: Input impedance 10 kΩ / Input sensitivity -10 dBm
120W (60W x 2) 80W (40W x 2) 40W (20W x 2)
14 cm x 2, 3 cm (dome type) x 2 14 cm x 2, 5 cm x 2 16 cm x 2
1427 x 506 x 969 mm 1414 x 512 x 887 mm 1397 x 515 x 870 mm 1397 x 515 x 871 mm 1379 x 515 x 851 mm
(56-3/16" x 19-15/16" x 38-1/8")
1427 x 506 x 1132 mm 1414 x 512 x 1051 mm 1397 x 515 x 1033 mm 1397 x 515 x 1037 mm 1379 x 515 x 1017 mm
(56-3/16" x 19-15/16" x 44-9/16")
CLP-880
70.0 kg (154.3 lbs.)
CLP-880PE
82.0 kg (180.8 lbs.)
(55-11/16" x 20-1/8" x 34-15/16")
(55-11/16" x 20-1/8" x 41-3/8")
(55" x 20-1/4" x 34-1/2") (55" x 20-1/4" x 34-5/16") (55" x 20-1/4" x 33-1/2")
(55" x 20-1/4" x 40-11/16") (55" x 20-1/4" x 40-13/16") (55" x 20-1/4" x 40-1/16")
56.0 kg (123.4 lbs.) 56.0 kg (123.4 lbs.) 53.0 kg (116.8 lbs.) 48.0 kg (105.8 lbs.)
• Specifications and descriptions in this owner’s manual are for information purposes only.
Yamaha Corp. reserves the right to change or modify products or specifications at any time
without prior notice. Since specifications, equipment or options may not be the same in
every locale, please check with your Yamaha dealer.
• Die technischen Daten und Beschreibungen in dieser Bedienungsanleitung dienen nur der
Information. Yamaha Corp. behält sich das Recht vor, Produkte oder deren technische
Daten jederzeit ohne vorherige Ankündigung zu verändern oder zu modifizieren. Da die
technischen Daten, das Gerät selbst oder Sonderzubehör nicht in jedem Land gleich sind,
setzen Sie sich im Zweifel bitte mit Ihrem Yamaha-Händler in Verbindung.
• Les caractéristiques techniques et les descriptions du mode d’emploi ne sont données que
pour information. Yamaha Corp. se réserve le droit de changer ou modifier les produits et
leurs caractéristiques techniques à tout moment sans aucun avis. Du fait que les
caractéristiques techniques, les équipements et les options peuvent différer d’un pays à
l’autre, adressez-vous au distributeur Yamaha le plus proche.
• Las especificaciones y descripciones de este manual del propietario tienen sólo el propósito
de servir como información. Yamaha Corp. se reserva el derecho a efectuar cambios o
modificaciones en los productos o especificaciones en cualquier momento sin previo aviso.
Puesto que las especificaciones, equipos u opciones pueden no ser las mismas en todos
los mercados, solicite información a su distribuidor Yamaha.
CLP-880/860/840/820/820S
68
IMPORTANT SAFETY INSTRUCTIONS
INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,
AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.
WARNING- When using any electrical or electronic prod-
uct, basic precautions should always be followed. These precautions include, but are not limited to, the following:
1. Read all Safety Instructions, Installation Instructions,
Special Message Section items, and any Assembly Instructions
found in this manual BEFORE marking any connections, including connection to the main supply.
2. Main Power Supply Verification: Yamaha products are
manufactured specifically for the supply voltage in the area
where they are to be sold. If you should move, or if any doubt
exists about the supply voltage in your area, please contact
your dealer for supply voltage verification and (if applicable)
instructions. The required supply voltage is printed on the
name plate. For name plate location, please refer to the graphic
found in the Special Message Section of this manual.
3. This product may be equipped with a polarized plug
(one blade wider than the other). If you are unable to insert the
plug into the outlet, turn the plug over and try again. If the
problem persists, contact an electrician to have the obsolete
outlet replaced. Do NOT defeat the safety purpose of the plug.
4. Some electronic products utilize external power sup-
plies or adapters. Do NOT connect this type of product to any
power supply or adapter other than one described in the owners
manual, on the name plate, or specifically recommended by
Yamaha.
5. WARNING: Do not place this product or any other
objects on the power cord or place it in a position where anyone could walk on, trip over, or roll anything over power or
connecting cords of any kind. The use of an extension cord is
not recommended! If you must use an extension cord, the
minimum wire size for a 25' cord (or less) is 18 AWG. NOTE:
The smaller the AWG number, the larger the current handling
capacity. For longer extension cords, consult a local electrician.
6. Ventilation: Electronic products, unless specifically
designed for enclosed installations, should be placed in locations that do not interfere with proper ventilation. If instructions for enclosed installations are not provided, it must be
assumed that unobstructed ventilation is required.
7. Temperature considerations: Electronic products
should be installed in locations that do not significantly contribute to their operating temperature. Placement of this product close to heat sources such as; radiators, heat registers and
other devices that produce heat should be avoided.
8. This product was NOT designed for use in wet/damp loca-
tions and should not be used near water or exposed to rain. Examples of wet/damp locations are; near a swimming pool, spa, tub,
sink, or wet basement.
9. This product should be used only with the components
supplied or; a cart, rack, or stand that is recommended by the
manufacturer. If a cart, rack, or stand is used, please observe all
safety markings and instructions that accompany the accessory
product.
10. The power supply cord (plug) should be disconnected from
the outlet when electronic products are to be left unused for extended periods of time. Cords should also be disconnected when
there is a high probability of lightning and/or electrical storm
activity.
11. Care should be taken that objects do not fall and liquids are
not spilled into the enclosure through any openings that may exist.
12. Electrical/electronic products should be serviced by a
qualified service person when:
a. The power supply cord has been damaged; or
b. Objects have fallen, been inserted, or liquids have been
spilled into the enclosure through openings; or
c. The product has been exposed to rain: or
d. The product dose not operate, exhibits a marked change
in performance; or
e. The product has been dropped, or the enclosure of the
product has been damaged.
13. Do not attempt to service this product beyond that de-
scribed in the user-maintenance instructions. All other servicing
should be referred to qualified service personnel.
14. This product, either alone or in combination with an ampli-
fier and headphones or speaker/s, may be capable of producing
sound levels that could cause permanent hearing loss. DO NOT
operate for a long period of time at a high volume level or at a
level that is uncomfortable. If you experience any hearing loss or
ringing in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period
before damage occurs.
15. Some Yamaha products may have benches and/or acces-
sory mounting fixtures that are either supplied as a part of the
product or as optional accessories. Some of these items are designed to be dealer assembled or installed Please make sure that
benches are stable and any optional fixtures (where applicable) are
well secured BEFORE using. Benches supplied by Yamaha are
designed for seating only. No other uses are recommended.
92-469-2
PLEASE KEEP THIS MANUAL
CLP-880/860/840/820/820S
69
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted
by the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with
the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a
reasonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with
other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful
to the operation of other electronic devices. Compliance with FCC
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in accordance with the following code:
BLUE : NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may
not correspond with the coloured makings identifying the terminals
in your plug proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the
terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of
the three pin plug.
regulations does not guarantee that interference will not occur in
all installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and
“ON”, please try to eliminate the problem by using one of the
following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker
or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please
contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed
by Yamaha Corporation of America or its subsidiaries.
(class B)
• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.
(2 wires)
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOND.
• This applies only to products distributed by Yamaha Canada Music Ltd.
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
(polarity)
For details of products, please contact your nearest Yamaha or the
authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Y amaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más cercana
o el distribuidor autorizado que se lista debajo.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
U.S.A.
Yamaha Corporation of America,
Keyboard Division
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de Mexico S.A. De C.V.,
Departamento de ventas
Javier Rojo Gomez No.1149, Col. Gpe Del
Moral, Deleg. Iztapalapa, 09300 Mexico, D.F.
Tel: 686-00-33
BRAZIL
Yamaha Musical do Brasil LTDA.
Av. Rebouças 2636, São Paulo, Brasil
Tel: 011-853-1377
ARGENTINA
Yamaha Music Argentina S.A.
Viamonte 1145 Piso2-B 1053,
Buenos Aires, Argentina
Tel: 1-371-7021
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha de Panama S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: 507-269-5311
EUROPE
THE UNITED KINGDOM
Yamaha-Kemble Music (U.K.) Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
IRELAND
Danfay Ltd.
61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin
Tel: 01-2859177
GERMANY/SWITZERLAND
Yamaha Europa GmbH.
Siemensstraße 22-34, 25462 Rellingen,
F.R. of Germany
Tel: 04101-3030
AUSTRIA
Yamaha Music Austria
Schleiergasse 20, A-1100 Wien Austria
Tel: 01-60203900
THE NETHERLANDS
Yamaha Music Nederland
Kanaalweg 18G, 3526KL, Utrecht, The Netherlands
Tel: 030-2828411
BELGIUM
Yamaha Music Belgium
Keiberg Imperiastraat 8, 1930 Zaventem, Belgium
Tel: 02-7258220
FRANCE
Yamaha Musique France,
Division Claviers
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
ITALY
Yamaha Musica Italia S.P.A.,
Home Keyboard Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha-Hazen Electronica Musical, S.A.
Jorge Juan 30, 28001, Madrid, Spain
Tel: 91-577-7270
GREECE
Philippe Nakas S.A.
Navarinou Street 13, P.Code 10680, Athens, Greece
Tel: 01-364-7111
SWEDEN
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1
Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
DENMARK
YS Copenhagen Liaison Office
Generatorvej 8B
DK-2730 Herlev, Denmark
Tel: 44 92 49 00
FINLAND
F-Musiikki Oy
Kluuvikatu 6, P.O. Box 260,
SF-00101 Helsinki, Finland
Tel: 09 618511
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1
N-1345 Østerås, Norway
Tel: 67 16 77 70
ICELAND
Skifan HF
Skeifan 17 P.O. Box 8120
IS-128 Reykjavik, Iceland
Tel: 525 5000
OTHER EUROPEAN COUNTRIES
Yamaha Europa GmbH.
Siemensstraße 22-34, 25462 Rellingen,
F.R. of Germany
Tel: 04101-3030
AFRICA
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2312
MIDDLE EAST
TURKEY/CYPRUS
Yamaha Europa GmbH.
Siemensstraße 22-34, 25462 Rellingen,
F.R. of Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
LB21-128 Jebel Ali Freezone
P.O.Box 17328, Dubai, U.A.E.
Tel: 971-4-81-5868
ASIA
HONG KONG
Tom Lee Music Co., Ltd.
11/F., Silvercord Tower 1, 30 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel: 2737-7688
INDONESIA
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
KOREA
Cosmos Corporation
1461-9, Seocho Dong, Seocho Gu, Seoul, Korea
Tel: 02-3486-0011
MALAYSIA
Yamaha Music Malaysia, Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 3-703-0900
PHILIPPINES
Yupangco Music Corporation
339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,
Makati, Metro Manila, Philippines
Tel: 819-7551
SINGAPORE
Yamaha Music Asia Pte., Ltd.
11 Ubi Road #06-00, Meiban Industrial Building,
Singapore
Tel: 65-747-4374
TAIWAN
Yamaha KHS Music Co., Ltd.
10F, 150, Tun-Hwa Northroad,
Taipei, Taiwan, R.O.C.
Tel: 02-2713-8999
THAILAND
Siam Music Yamaha Co., Ltd.
121/60-61 RS Tower 17th Floor,
Ratchadaphisek RD., Dindaeng,
Bangkok 10320, Thailand
Tel: 02-641-2951
THE PEOPLE’S REPUBLIC OF CHINA
AND OTHER ASIAN COUNTRIES
Yamaha Corporation,
International Marketing Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2317
OCEANIA
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
17-33 Market Street, South Melbourne, Vic. 3205,
Australia
Tel: 3-699-2388
NEW ZEALAND
Music Houses of N.Z. Ltd.
146/148 Captain Springs Road, Te Papapa,
Auckland, New Zealand
Tel: 9-634-0099
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
International Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-2312
[CL] 19
HEAD OFFICE
Yamaha Corporation, Electronic Musical Instrument Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: 053-460-3273
M.D.G., EMI Division, Yamaha Corporation
© 1998 Yamaha Corporation
V320140 911POCP2.3-07D0 Printed in Japan
This document is printed on chlorine free (ECF) paper.
Loading...