Yamaha CDR200tx User Manual

CDR200tx

User Guide

Guide de I’utilisateur

Bedienungsanleitung

READ/
WRITE

ON/
DISC

Recordable

VOL

READ

WRITE

6

2

CDR-200tx

POWER

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Systems Technology, Inc.

Address: 100 Century Center Court

San Jose, California 95112

Telephone: [phone]

FAX: [phone]

Type of Equipment: CD Recorder

Model Name: CDR200tx

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that
may cause undesired operation.
See user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (U.S.A.)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/
s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B”
digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a
residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio
frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful
to the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur
in all installations. If this product is found to be the source of interference, which can be determined by turning the product “OFF”
and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead­in to coaxial type cable.
If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type
of product. If you can not locate the appropriate retailer, please contact Yamaha Systems Technology, Inc. 100 Century Center
Court, San Jose, CA95112, U.S.A.

Laser Diode Properties

Material : GaAlAs
Wavelength : 780-790 nm
Emission Duration : Continuous
Laser Output Power : Less than 44.6 µW*

*

T

his output is value measured at a
distance 200mm from the objective lens
surface on the optical pick-up block.
ANSI Class : Class 1

CLASS 1 LASER PRODUCT

LASER KLASSE 1 PRODUKT

LUOKAN 1 LASERLAITE

PRODUIT LASER DE CLASSE 1

CAUTION

Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.

ADVARSEL

USYNLIG LASERSTRÅLING VED ÅBNING.
UNDGÅ UDSAETTELSE FOR STRÅLING.

VAROITUS

LAITTEEN KÄYTTÄMINEN MUULLA
KUIN TÄSSÄ KÄYTTÖOHJEESA
MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN
TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE.

VARNING

OM APPARATEN ANVÄNDS PÅ ANNAT
SÄTT ÄN I DENNABRUKSANVISNING
SPECIFICERATS, KAN ANVÄNDAREN
UTSÄTTAS FÖR OSYNLIG
LASERSTRÅLNING, SOM ÖVERSKRIDER
GRÄNSEN FÖR LASERKLASS 1.

This compact disc player is
classified as a CLASS 1
LASER product.
The CLASS 1 LASER
PRODUCT label must be
located on the exterior.

VORSICHT : UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG
GEOFFNET. NICHT DEM STRAHL AUSSETZEN.

VARNING : OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD OCH
SPÄRREN ÄR URKOPPLAD. BETRAKTA EJ STRÅLEN ÄR FARLIG.

VARO! : AVATAESSA JA SUOJALUKITUS OHITETTAESSA OLET
ALTTINA NÄKYMÄTTÖMÄLLE LASERS TEILYLLE. ÄLÄ KATSO SÄTESSEN.

ADVARSEL : USYNLIG LASERSTRALNING VED ÅBNING NÄR SIKKERHETSAF­ BYDERE ER UDE AF FUNKTION. UNDGÅ UDSETTELS FOR STRÅLING.

Varningsanvisning för
laserstrålning.

Important Precautions

Important Precautions

Please read the following precautions before operating
CDR200tx.

• Do not remove the CDR200tx’s top cover.
This device uses semiconductor laser.
Refer all servicing to qualified personnel.

• Do not attempt to touch the inside of the
CDR200tx. Electricity may have been built up
even after you turn off the power.

• CDR200tx is a sophisticated electronic device.
Handle it with care.

• If the fuse blows, CDR200tx should be checked
by a qualified engineer. Do not just replace the
fuse. Replacing the fuse by yourself may cause
the protection circuit to be damaged.

• The CDR200tx uses high-density circuits and LSIs.
Even a small incident may cause malfunctions to
occur.

• If CDR200tx operates incorrectly, See “Trouble­shooting” on page 12. If the problem persists,
consult your CDR200tx dealer.

• Yamaha is not responsible for any data or infor­mation losses resulting from the operation of
CDR200tx.

i

Installation Precautions

• Install CDR200tx on a level surface.

• Do not install CDR200tx near water, in direct sunlight,

close to heating units, or in areas subject to high or low
temperature extremes, excessive dust, vibration, or severe
shocks.

• Do not expose CDR200tx to extremes of humidity.

• The ambient temperature where CDR200tx is installed

should be between 5°C and 40°C (41°F–104°F).

• Using CDR200tx close to a television or radio may cause

interference. Install CDR200tx at least one meter away
from television and radio equipment.

• Do not block the CDR200tx ventilation slots. Install

CDR200tx with at least 10 cm of free space all-around.

• Make sure the CDR200tx power cord is not located in a

position where it is likely to be walked on or pinched by
other equipment.

Important Precautions

ii

Important Precautions

Operating Precautions

• Do not subject CDR200tx to impact or shock when in use.
This may impair recording or playback.

• Do not place heavy objects on CDR200tx.

• Avoid moving CDR200tx from cold to warm places, and
avoid sudden room temperature rises, as condensation
that could cause CDR200tx to malfunction may occur. If
condensation does occur, wait at least one hour before
operating CDR200tx.

• Do not let liquid or other foreign objects enter CDR200tx.

• To reduce the risk of electric shock, do not expose
CDR200tx to rain or moisture.

• Always remove the disc before transporting CDR200tx.

• CDR200tx uses an optical pickup that is sensitive to dust
and dirt. Make sure that the disc tray and disc are free of
dust and dirt before loading.

• Use only the power cable supplied. Other cables may cause
interference when CDR200tx is used near to radio and
television equipment.

iii

• CDR200tx should be connected only to an AC receptacle
of the type described in this
the rear panel of CDR200tx.

• Use a soft dry cloth to clean CDR200tx. Stubborn dirt can
be removed using a cloth dampened with water and neutral
detergent solution. Do not use benzine or solvent based
cleaners on CDR200tx.

User Guide

or as marked on

Preventing Premature Disc Failure

Preventing Premature Disc Failure

The NUMBER ONE cause of premature disc failure with
recordable CDs is contamination of the recording surface
before recording is completed. To minimize disc failure, use
the following disc-handling guidelines:

• Keep the disc tray and disc as clean and dust-free

humanly possible

touch the recording surface, and do not expose the disc tray
and disc to dust or dirt.

• DO NOT BLOW ON THE DISC to remov e dust or dirt. To

remove dust from the recording surface use a camera lens
bulb. Be sure to follo w the instructions when using the cloth.

• To remove stubborn dirt or grease from the recording surface

use only nonabrasive foam-tipped swabs (such as Chemtron­ics Foamtips #120) with a
alcohol. To avoid scratching the recording surface BE SURE
TO USE ONLY LIGHT STROKES, be ginning at the disc
center, pulling directly tow ards the disc’s outer edge.

• Always record in a dust-free environment. If the disc must

be removed from CDR200tx before recording is finished,
store the disc in a clean, dust-free environment.

• If a disc tray accumulates dust, DO NOT USE IT FOR

DISC RECORDING. Always use a clean, dust-free tray
for disc recording.

If CDR200tx is vibrated while recording, the recording may
fail. To avoid such failures observe the following practices:

• Place CDR200tx on a solid, stable surface, away from

high-traffic areas. The surface must allow CDR200tx to
operate in a level, horizontal position.

during the record process. DO NOT

small amount

of pure, denatured

as

• Avoid touching or handling CDR200tx when recording.

Note:

Once the disc has been finalized (and no more recording is
possible), it can be handled with the same care that any CD
should be handled.

iv