Yamaha BDX-610 User Manual [ru]

Blu-ray Disc Receiver
BRX-610
TLF
Owner’s Manual
Manual de Instrucciones
Инструкция по эксплуатации
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1 To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2 Install this sound system in a well ventilated, cool, dry,
clean place - away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. For proper ventilation, allow the following minimum clearances. Top: 10 cm Rear: 10 cm Sides: 10 cm
3 Locate this unit away from other electrical appliances,
motors, or transformers to avoid humming sounds.
4 Do not expose this unit to sudden temperature changes
from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.
5 Avoid installing this unit where foreign object may fall
onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place:
– Other components, as they may cause damage and/or
discoloration on the surface of this unit.
– Burning objects (i.e. candles), as they may cause fire,
damage to this unit, and/or personal injury.
– Containers with liquid in them, as they may fall and
liquid may cause electrical shock to the user and/or damage to this unit.
6 Do not cover this unit with a newspaper, tablecloth,
curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.
7 Do not plug in this unit to a wall outlet until all
connections are complete.
8 Do not operate this unit upside-down. It may overheat,
possibly causing damage. 9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cable from the wall outlet,
grasp the plug; do not pull the cable. 11 Do not clean this unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth. 12 Only voltage specified on this unit must be used. Using
this unit with a higher voltage than specified is dangerous
and may cause fire, damage to this unit, and/or personal
injury. Yamaha will not be held responsible for any
damage resulting from use of this unit with a voltage
other than specified. 13 To prevent damage by lightning, keep the power cable
and outdoor antennas disconnected from a wall outlet or
this unit during a lightning storm. 14 Do not attempt to modify or fix this unit. Contact
qualified Yamaha service personnel when any service is
needed. The cabinet should never be opened for any
reasons. 15 When not planning to use this unit for long periods of
time (i.e. vacation), disconnect the AC power plug from
the wall outlet. 16 Be sure to read the “TROUBLESHOOTING” section on
common operating errors before concluding that this unit
is faulty.
17 Before moving this unit, press to set this unit to the
standby mode, and disconnect the AC power plug from the wall outlet.
18 Condensation will form when the surrounding
temperature changes suddenly. Disconnect the power cable from the outlet, then leave this unit alone.
19 When using this unit for a long time, this unit may
become warm. Turn the power off, then leave this unit alone for cooling.
20 Install this unit near the AC outlet and where the AC
power plug can be reached easily.
21 The batteries shall not be exposed to excessive heat such
as sunshine, fire or the like.
This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off by . This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
LASER SAFETY
This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device.
DANGER
This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When this unit is plugged into the wall outlet, do not place your eyes close to the opening of the disc tray and other openings to look into inside.
WARNING
DO NOT TOUCH THIS UNIT WHEN IT IS USED CONTINUOUSLY AT HIGH VOLUME BECAUSE THE BOTTOM OF THIS UNIT MAY BECOME HOT. IT MAY LEAD TO INJURIES SUCH AS BURNS, ETC.
i En
INTRODUCTION
WHAT YOU CAN DO WITH THIS UNIT ......... 2
SUPPLIED PARTS ................................................ 2
ABOUT DISCS AND FILES ................................. 3
Types of discs/files that can be used with this unit ... 3
Loading a disc............................................................ 4
Disc precautions......................................................... 4
Notice for watching 3D video images ....................... 4
PART NAMES AND FUNCTIONS...................... 5
Front panel ................................................................. 5
Remote control........................................................... 6
Rear panel .................................................................. 9
Installing the batteries in the remote control ........... 10
Using the remote control ......................................... 10
PREPARATIONS
CONNECTION..................................................... 11
5.1-channel speaker layout ...................................... 11
Connecting speakers ................................................ 11
Connecting the FM antenna..................................... 12
Connecting iPod....................................................... 12
Connecting to a TV.................................................. 13
Connecting a satellite/cable TV tuner...................... 14
Connecting audio devices (such as a CD or MD
player).................................................................. 14
Connecting a portable digital music player
other than iPod..................................................... 14
NETWORK AND USB CONNECTION............ 15
Connecting to the NETWORK terminal.................. 15
Connecting to the USB port..................................... 15
OTHER CONNECTION ..................................... 16
Connecting the power cable..................................... 16
OPERATIONS
INITIAL WIZARD/EASY SETUP ..................... 17
Setting with the Initial Wizard/Easy Setup.............. 17
BASIC OPERATION........................................... 18
Playing back photo/music/video.............................. 20
Using network content............................................. 22
Using network services............................................ 22
Operation for iPod ................................................... 23
Operation for CDs.................................................... 23
ADVANCED PLAYBACK OPERATION......... 24
On Screen menu....................................................... 24
Status menu.............................................................. 25
Using Bookmark...................................................... 26
Program play............................................................ 26
Using search............................................................. 26
Enjoying BONUSVIEW™ and BD-Live™ ............ 27
LISTENING TO FM RADIO STATIONS ........ 28
Tuning to radio stations ........................................... 28
Presetting radio stations........................................... 28
Selecting preset radio stations (Preset tuning)......... 28
Deleting preset stations............................................ 29
Displaying Radio Data System information (Russia model only)
USING USEFUL FUNCTIONS .......................... 30
Setting the sleep timer ............................................. 30
Operating this unit by TV remote control
(the HDMI control function) ............................... 30
CONTENTS
SETTINGS
SETUP MENU.......................................................32
SOFTWARE UPGRADE .....................................41
ADDITIONAL INFORMATION
TROUBLESHOOTING .......................................42
GLOSSARY...........................................................50
SPECIFICATIONS...............................................51
About this manual
• This manual describes how to operate this unit using a remote control except when it is not available. Some of these operations are also available using the front panel buttons.
• Notes contain important information about safety and operating instructions. y indicates a tip for your operation.
• “iPod” described in this manual may also refer to “iPhone”.
• This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In case of differences between the manual and the product, the product has priority.
The icons used in this manual
Icons are used to indicate available buttons/functions for a particular format.
: BD-Video
BD DVD
: Audio CD
CD VIDEO MUSIC
.. 29
PHOTO
Operation for SETUP menu .................................... 34
General Setting ........................................................ 35
Display Setting ........................................................ 37
Audio Setting........................................................... 39
About the video output formats ............................... 40
Upgrading the software............................................ 41
General..................................................................... 42
Radio reception........................................................ 44
iPod.......................................................................... 44
USB ......................................................................... 45
Disc playback .......................................................... 46
Remote control ........................................................ 47
Network ................................................................... 47
Messages on the screen............................................ 49
Others....................................................................... 49
: DVD-Video, DVD-VR, DVD+VR
: AVCHD, WMV : MP3, WMA, WAV
: JPEG
INTRODUCTION PREPARATIONS
OPERATIONS SETTINGS
INFORMATION
ADDITIONAL
English
1 En
INTRODUCTION
WHAT YOU CAN DO WITH THIS UNIT
Blu-ray 3D Disc (Blu-ray Disc™)/DVD/CD Playback
Play back commercially-released Blu-ray 3D Discs (BD discs), in addition to DVDs and CDs.
BONUSVIEW™ and BD-Live™ Playback
Download additional contents available via BD-Live™ supported BD discs, and enjoy secondary audio/video on BONUSVIEW™-supported BD discs.
USB Digital Connection for iPod and iPhone
Direct USB cable connection to an iPod or iPhone enables high quality digital sound without any degradation caused by digital-to-analog conversion.
Home Network Server (DLNA supported)
Enjoy a variety of PC contents on your TV by connecting to a network server.
*1
*1
*1, 2
YouTube™ Contents Playback (Russia and Asia models only)
Enjoy YouTube™ contents on your TV.
Receiving FM Radio and Radio Data System Information
*1
*2
\ p. 24
\ p. 27
\ p. 19
\ p. 22
\ p. 22
\ p. 28
(Russia model only)
Listen to FM radio. Radio Data System broadcasts provide program information on the front panel display (Russia model only).
Initial Wizard and Easy Setup \ p. 17
Easily set language, resolution, screen aspect ratio with the Initial Wizard/Easy Setup screen.
Operate with the TV Remote Control (HDMI CEC supported) \ p. 30
HDMI control function (using HDMI cable connection) provides multiple device operation with a single remote control.
*1For details on playable discs and files, refer to page 3.
2
Network setting is needed to use this function.
*
SUPPLIED PARTS
Make sure you have all of the following items.
Remote control Indoor FM antenna
*3The supplied indoor FM antenna differs depending on your model.
4
*
The power cable differs depending on your model.
Batteries (×2)
(AAA, R03, UM-4)
*3
Composite video
cable (1.5m)
Power cable
*4
2 En
ABOUT DISCS AND FILES
Types of discs/files that can be used with this unit
• 12 cm and 8 cm discs can be played back in this unit. Do not use an 8 cm to 12 cm adapter.
• Use discs that conform to compatible standards as indicated by the presence of official logos on the disc label. Playback of discs not complying with these standards is not guaranteed. In addition, the image quality or sound quality is not guaranteed even if the discs can be played back.
Disc Type
BD-ROM/BD-R/ BD-RE
DVD-ROM DVD-Video -­DVD-R/DVD-R DL/
DVD-RW
DVD+R/DVD+R DL/DVD+RW
CD-ROM CDDA/HDCD -­CD-R/CD-RW CDDA/Data Disc WMV/MP3/WAV/
USB -- WMV/MP3/WAV/
Network -- WMV/MP3/WMA/
Region management information
Destination BD-Video DVD-Video
U.S.A. and Canada Region code “A” or
Recording
Format
BD-Video --
DVD-Video/DVD­VR/AVCHD/Data Disc
DVD-Video/ DVD+VR/AVCHD/ Data Disc
“ALL”
Data Format
WMV/MP3/WAV/ WMA/JPEG
WMV/MP3/WAV/ WMA/JPEG
WMA/JPEG
WMA/JPEG
WAV/JPEG
Region number “1” or “ALL”
Region management information
Destination BD-Video DVD-Video
Europe Region code “B” or
“ALL”
Australia Region code “B” or
“ALL”
Russia Region code “C” or
“ALL”
China Region code “C” or
“ALL”
Region number “2” or “ALL”
2
Region number “4” or “ALL”
4
Region number “5” or “ALL”
5
Region number “6” or “ALL”
ALL
ALL
ALL
ALL
• BD/DVD video players and discs have region codes, which dictate the regions in which a disc can be played.
• BD/DVD Video operations and functions may be different from the explanations in this manual and some operations may be prohibited due to disc manufacturer’s settings.
• If a menu screen or operating instructions are displayed during playback of a disc, follow the operating procedure displayed.
INTRODUCTION
Asia Region code “A” or
Central and South America
“ALL”
Region code “A” or “ALL”
1
Region number “3” or “ALL”
3
Region number “4” or “ALL”
4
ALL
ALL
ALL
Notes
• Playback for some of the discs in the left side column tables
may not be possible depending on the disc.
• Finalize all recording media that is played back in this unit.
• “Finalize” refers to a recorder processing a recorded disc so that
it will play in other players/recorders as well as this unit. Only finalized discs will play back in this unit. (This unit does not have a function to finalize discs.)
• Playback of all files on the disc, USB memory device and
network is not guaranteed.
• A copyright protected file cannot be played back via a USB
memory device and network.
MP3/WMA audio file requirement
• Sampling frequency: within 32 - 48 kHz (MP3/WMA), LPCM 44.1 kHz/16 bit/Stereo (WAV)
• Bitrate: within 8 - 320 kbps (MP3), 32 - 192 kbps (WMA)
WMV file requirement
• WMV9, maximum resolution is 1,920 × 1,080.
3 En
English
ABOUT DISCS AND FILES
Loading a disc
• Insert the disc with the label facing up.
• In case of the disc recorded on both sides, face down the side you want to play back.
Notes
• Playback may begin automatically, depending on the disc and
setting of this unit.
• The menu may be displayed first, depending on the disc.
• The disc load time may vary depending on the disc.
Disc precautions
• Do not touch the surface of the disc. Hold a disc by its edge (and the center hole).
• Do not use a pencil or pointed marker to write on the disc.
• Do not put a tape, seal, glue, etc., on a disc.
• Do not use a protective cover to prevent scratches.
• Do not load more than one disc into this unit at one time. This can cause damage to both this unit and the discs.
• Do not insert any foreign objects into the disc slot.
• Do not load a cracked, warped, or glued disc.
• Do not expose a disc to direct sunlight, high temperature, high humidity, or a lot of dust.
Caution
Notice for watching 3D video images
• Some people may experience discomfort (such as eye strain, fatigue, or nausea) while watching 3D video images. We recommend that all viewers take regular breaks while watching 3D video images.
• If you experience any discomfort, stop watching the 3D video images until the discomfort subsides. Consult a doctor if you experience severe discomfort.
• Read the owner’s manuals (BD disc and TV) and/or the caution messages that appear on the TV carefully.
• The vision of young children (especially those under six years old) is still under development. Consult your doctor (such as a pediatrician or eye doctor) before allowing young children to watch 3D video images.
• Adults should supervise young children to ensure they follow the recommendations described above.
• If a disc becomes dirty, wipe it with a clean, dry cloth from the center out to the edge. Do not use record cleaner or paint thinner.
• To avoid malfunction, do not use a commercially available lens cleaner.
4 En
Front panel
PART NAMES AND FUNCTIONS
INTRODUCTION
USB PORTABLE
iPod/iPhone
2 3 4 6 7 8159 0 A B
1 (On/Standby):
Turns this unit on/Sets to standby mode.
y
This unit has an automatic standby function.
• When the source is set to Disc/USB/Network, this unit automatically switches to standby mode if it is left turned on for 1 hour without playback or any other operation being performed.
• When the source is NOT set to Disc/USB/Network, this unit automatically switches to standby mode if it is left turned on for between 1 to 8 hours without playback or any other operation being performed according to the setting in SETUP menu (p. 35).
2 iPod/iPhone/USB port (p. 12, 15):
Connect your iPod or USB memory device.
3 PORTABLE (p. 14):
Connect a portable digital music player other than iPod.
4 Disc tray door 5 Front panel display
6 (Eject):
Opens/Closes the disc tray.
7 (Play/Pause):
Starts/Pauses playback.
8 (Stop) 9 (Search backward/Skip backward):
Press to skip backward, and press and hold to search backward.
PRESET <:
Press to select a preset station.
0 (Search forward/Skip forward):
Press to skip forward, and press and hold to search forward.
PRESET >:
Press to select a preset station.
A INPUT:
Selects the input source.
B VOLUME:
Turns the volume up/down.
5 En
English
PART NAMES AND FUNCTIONS
Remote control
Note
will appear on the top left corner of the screen when the
pressed button is not available.
1 2
3 4
5
6 7 8
9 0
A B
C D E
F
PROGRAM MARKER DIGEST ZOOM
SLEEP
SW
MUTESEARCHCLEAR
SETUP
DISPLAY
OPTION
TOP MENU
RETURN ON SCREEN
DIMMER
STATUS
PIP
SUBTITLE
SHUFFLE
REPEAT
iPod
TV
DISC
USB NET
HOME
ENTER
AUDIO
A B
STB
AUX
VOLUME
POP-UP MENU
TUNING
PRESET
MEMORY
TUNER
PORTABLE
G H
I J K
L
M
N
O
P
Q R
1 Infrared signal transmitter (p. 10) 2 MARKER : Sets Bookmark at a specified
DVD VIDEO
point of a movie (p. 26). After Bookmark is set, press DIGEST to select the set point you want to jump to. You can set up to 12 Bookmarks.
3 : Opens/Closes the disc tray. 4 PROGRAM : Sets the order of playback
DVD CD
(p. 26). You can set up to 15 tracks of an audio disc or titles/ chapters of a DVD-Video disc.
5 Numeric buttons: Enters numbers, or during playback,
jumps to the track/chapter corresponding to the number you input. These buttons may not be available depending on the disc type and playback condition.
6 CLEAR: Clears entered number/set item. 7 DISPLAY: Switches the information shown on the front
panel display (p. 23, 29).
8 SETUP: Displays SETUP menu screen (p. 32). 9 OPTION: Enters option menu mode (p. 29). 0 HOME: Displays HOME menu screen (p. 20). A STATUS: Displays the playback information on the screen
(p. 25).
B DIMMER: Changes brightness of the front panel display.
Choose brightness from normal (bright), mid dim, or dim by pressing this button repeatedly.
C SUBTITLE : Changes subtitle
BD DVD VIDEO
languages (p. 50) if available. You can also select this item from On Screen menu (p. 24).
D PIP : Turns on/off the Picture in Picture (p. 27). PIP
BD
Mark ( ) is displayed on the screen when this function is available. You can also select this item from On Screen menu (p. 24).
Note
PIP Mark is displayed only when [PIP Mark] is set to [On] (p. 36).
E REPEAT
PHOTO
will change each time you press the button (p. 23, 25).
F SHUFFLE :
Selects shuffle play mode (p. 23, 24).
G DIGEST : Shows 12 photo thumbnails. When
thumbnails are displayed, you can proceed to the next/ previous page with / .
DVD VIDEO
H : Turns this unit on or sets it to standby mode.
BD DVD CD VIDEO MUSIC
: Selects repeat mode. Repeat mode shown below
: Repeats the title being played back. : Repeats the chapter being played back. : Repeats the folder being played back. : Repeats all tracks/files on the disc/folder. : Repeats the track/file being played back.
DVD CD VIDEO MUSIC PHOTO
PHOTO
: Displays Bookmark select bar (p. 26).
6 En
PART NAMES AND FUNCTIONS
\
I ZOOM : Zooms in/out. The
J Color buttons : Use these buttons according to on-
K SLEEP: Sets to sleep mode (p. 30). L Subwoofer volume control buttons
M Volume control buttons: Controls the volume level.
N SEARCH : Jumps
O AUDIO : Changes the audio language or
P FM control buttons
Q A/B : Plays back a
DVD VIDEO PHOTO
size of the screen will change each time you press the button (zoom in/out: 3 steps each).
screen instructions.
: Controls the subwoofer volume
CD VIDEO MUSIC
level (p. 12).
Press MUTE to turn off the volume. Press again to resume the volume.
to a specified point during playback. For details on this function, refer to “Using search” (p. 26). You can also select this item from Status menu (p. 25).
format. You can also select from On Screen menu (p. 24).
TUNING << / >>: Starts manual tuning. Press and hold to start automatic tuning (p. 28).
PRESET < / >: Selects preset station (p. 28). MEMORY: Starts preset tuning and stores preset stations
(p. 28).
BD DVD CD VIDEO MUSIC
specific part you want to repeat. 1 Press A/B at the scene where you want to set the start
point. [A-] is displayed on the screen.
2 Press A/B again at the scene where you want to set the end
point. [A-B] is displayed on the screen. Repeat playback starts.
3 To cancel the repeat playback, press A/B. [A-B]
disappears and the repeat playback is finished.
BD
BD DVD
BD DVD CD VIDEO MUSIC
BD DVD
Note
This function cannot be performed depending on the specifications of the disc.
R Input select buttons: Selects the input source (p. 18, 28).
INTRODUCTION
Continued to the next page.
English
7 En
PART NAMES AND FUNCTIONS
S
t
U
PROGRAM MARKER DIGEST ZOOM
SLEEP
SW
MUTESEARCHCLEAR
SETUP
DISPLAY
OPTION
TOP MENU
RETURN ON SCREEN
DIMMER
STATUS
PIP
SUBTITLE
SHUFFLE
REPEAT
iPod
TV
DISC
USB NET
HOME
ENTER
AUDIO
A B
STB
AUX
VOLUME
POP-UP MENU
TUNING
PRESET
MEMORY
TUNER
PORTABLE
V
W
X
S TOP MENU : Displays the top menu screen
BD DVD
(p. 51) if the disc contains a menu. Select the desired item using 5 /a /2 /3 and ENTER.
Note
Specific operations may be different depending on the disc. Follow the instructions of each menu screen.
T Cursor buttons (5/a /2 /3): Moves to select the focused
item. ENTER: Confirms the focused menu/item.
U RETURN: Returns to the previous menu or screen, etc. V POP-UP/MENU : Displays pop-up menu. The
menu contents displayed vary depending on the disc. For details on how to see and operate the pop-up menu, refer to the manual for the disc. The top menu screen may be displayed by pressing POP-UP/MENU depending on the disc.
W ON SCREEN: Displays On Screen menu (p. 24). X Control buttons
:
BD DVD CD VIDEO MUSIC PHOTO
: Plays back contents. : Stops playback. To stop playback completely, press this
button twice.
: Pauses playback.
:
BD DVD CD VIDEO MUSIC
/ : Skips backward/forward.
/ : Press for instant search/replay. Instant search skips the content 30 seconds. Instant replay replays the content from 10 seconds before.
:
BD DVD CD VIDEO MUSIC
/ : Searches backward/forward. The search speed will change each time you press the button (search backward/ forward: 5 steps each). Press to resume normal playback.
PHOTO
/ : Changes the speed of a slide show (slower/ faster: 3 steps).
BD DVD
:
8 En
Note
Depending on the disc, this unit resumes playback from the point where the unit was previously stopped. To play back from the beginning, press and then press .
Rear panel
PART NAMES AND FUNCTIONS
INTRODUCTION
2 4 5 6 7 8931
1 AC IN jack (p. 16):
Connect the supplied power cable.
2 SPEAKERS terminals (p. 11):
Connect speakers.
3 ANTENNA jack (p. 12):
Connect an FM antenna.
4 REMOTE CONTROL (IN/OUT) jacks (U.S.A.
and Canada models only):
Connect other components for remote control.
5 DIGITAL IN (COAXIAL/OPTICAL) jacks
(p. 13, 14):
Connect your satellite or cable TV tuner to the COAXIAL jack. The OPTICAL jack is for the audio signal from your TV when your TV is not ARC (Audio Return Channel) supported.
6 AUDIO IN (AUX) jacks (p. 14):
Connect other audio devices such as a CD or MD player.
7 OUTPUT (VIDEO/SUBWOOFER/HDMI) jacks
(p. 12, 13):
The VIDEO jack outputs analog video signal. Use the SUBWOOFER jack when you are using an active subwoofer speaker (built-in amplifier). Use the HDMI jack to connect to your TV.
8 NETWORK (LAN) jack (p. 15):
Connect your hub or broadband router.
9 USB jack (p. 15):
Connect a USB memory device.
9 En
English
PART NAMES AND FUNCTIONS
2
Installing the batteries in the remote control
1
3
2
Notes on batteries
• Change both batteries when the operation range of the remote control decreases.
• Use AAA, R03, UM-4 batteries.
• Make sure that the polarities are correct. Refer to the illustration inside the battery compartment.
• Remove the batteries if the remote control is not to be used for an extended period of time.
• Do not use old batteries together with new ones.
• Do not use different types of batteries (such as alkaline and manganese batteries) together. Read the packaging carefully as these different types of batteries may have the same shape and color.
• If the batteries have leaked, dispose of them immediately. Avoid touching the leaked material or letting it come into contact with clothing, etc. Clean the battery compartment thoroughly before installing new batteries.
• Do not throw away batteries with general house waste; dispose of them correctly in accordance with your local regulations.
• Keep batteries away from children. If a battery is accidentally swallowed, contact your doctor immediately.
• When not planning to use the remote control for long periods of time, remove the batteries from the remote control.
• Do not charge or disassemble the supplied batteries.
Using the remote control
The remote control transmits a directional infrared beam. Be sure to aim the remote control directly at the remote control sensor on the front panel of this unit during operation.
USB PORTABLE
iPod/iPhone
Within 6 m (20 feet)
30˚ 30˚
Notes
• The area between the remote control and this unit must be clear of large obstacles.
• Do not spill water or other liquids on this remote control.
• Do not drop the remote control.
• Do not leave or store the remote control in the following types of conditions:
– high humidity, such as near a bath – high temperature, such as near a heater or a stove – extremely low temperatures – dusty places.
• Do not expose the remote control sensor to strong lighting, in particular, an inverter type fluorescent lamp; otherwise, the remote control may not work properly. If necessary, position the system away from direct lighting.
10 En
PREPARATIONS
CONNECTION
5.1-channel speaker layout
FR
FL
SL
Front speakers (FR and FL):
For the front channel sound (stereo sound) and effect sound.
Center speaker (C):
For the center channel sound (dialogue, vocals, etc.).
Surround speakers (SR and SL):
For effect and vocal sound from surround channel. The surround back channel sound is output from the surround speakers when a disc which has 7.1- or 6.1-channel sounds is played back.
C
SW
SR
Notes
• Disconnect the power plug before connecting speakers.
• When connecting speakers, use speakers having more than 6Ω impedance for the front, center and surround speakers, and 4Ω to 6Ω impedance for a passive subwoofer. For an active subwoofer (built-in amplifier), you need not be concerned about impedance.
• When connecting an active subwoofer (built-in amplifier), be sure turn it off before connecting to the unit.
• Be careful that the core of the speaker cable does not touch anything or come into contact with the metal areas of the unit. This may damage the unit or the speakers.
Necessary cables (not supplied)
When the subwoofer is passive:
• Speaker cables × 6
+ –
When the subwoofer is active:
• Speaker cables × 5
+ –
• Monaural pin cable (for subwoofer) × 1
The rear panel of this unit
(when the subwoofer is passive)
+ –
+ –
PREPARATIONS
Subwoofer (SW):
For low-frequency effect (LFE) sound and bass sound from front and surround channels.
Connecting speakers
Connect speakers to the unit. When you are using a subwoofer speaker, check if it is active (built-in amplifier, with power cable) or passive (not built-in amplifier, without power cable). The cable used for connecting a subwoofer differs depending on the subwoofer type. After connecting the speakers, setting according to the speaker type (size, number of available speakers, etc.) is required. See page 39 for speaker setting.
English
11 En
CONNECTION
3
4
2
1
Connecting speaker cables
Each speaker has two speaker cables. One is for connecting the – (negative) terminal of the unit and the speaker, and the other is for the + (positive) terminal. The cables are different colors, so they do not get mixed up. Connect the black side to the – (negative) terminal and the other side to the + (positive) terminal.
2
4
1
3
Connecting the FM antenna
You can enjoy listening to FM radio stations by connecting the supplied indoor FM antenna.
1 Remove approximately 10 mm of insulation from the
end of the speaker cable and twist the bare wire firmly.
2 Press the tab on the speaker terminal down. 3 Insert the bare wire of the speaker cable into the
terminal.
4 Lift the tab to secure the speaker cable.
Connecting an active subwoofer
When connecting an active subwoofer (built-in amplifier), use a monaural pin cable. Before connecting an active subwoofer, turn it off.
Monaural pin cable
About subwoofer speaker
• Use the speaker terminal to connect a passive subwoofer speaker. Use the SUBWOOFER output jack to connect an active subwoofer speaker (built-in amplifier).
• You can adjust the subwoofer volume level by using this unit’s remote control. For an active subwoofer speaker (built-in amplifier), you can also use the control on the subwoofer to adjust volume level. Use these functions to decrease the volume level if strange noise or sound is output from the subwoofer.
• If you are not using a subwoofer speaker, select SETUP menu = [Audio Setting] = [Speaker Setting] = [Configuration] = [SW] = [Disable].
Note
If there is a problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use commercially available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center.
Connecting iPod
You can enjoy music stored in your iPod by connecting it to this unit.
Note
This unit is compatible with iPod classic, iPod nano (2nd, 3rd, 4th, 5th and 6th generation), iPod touch (1st, 2nd, 3rd, and 4th generation), iPhone, iPhone 3G/3GS, and iPhone 4.
USB PORTABLE
iPod/iPhone
Notes
• Make sure the USB cable is connected securely between your iPod and this unit.
• Connect your iPod to the front USB port of this unit. The rear USB port is not compatible with your iPod.
USB port
12 En
CONNECTION
Connecting to a TV
Make sure you refer the following illustration carefully so that connections between this unit and your TV are properly made.
CAUTION
Do not connect the power cable of this unit until all connections are completed.
1 Connect your TV using an HDMI cable (commercially available). The digital video signal is output from this unit to
your TV. If your TV’s HDMI terminal is ARC (audio return channel) supported, steps 2 to 3 are not necessary since digital audio signal is output from the TV to the unit through the HDMI cable.
2 Connect your TV using an optical cable (commercially available) to play back TV digital audio through this unit. 3 If an HDMI connection is unavailable, connect your TV using a video pin cable. Analog video signal is output from
this unit to your TV.
PREPARATIONS
This unit
3 Composite video cable
(supplied)
1 HDMI cable
(commercially available)
HDMI connection
• You can enjoy high quality digital picture and sound through the HDMI terminals.
• Firmly connect an HDMI cable (commercially available) to the HDMI terminal of this unit.
• Use HIGH SPEED HDMI cables that have the HDMI logo (p. 52).
y
• When you use the HDMI control function, refer to “Operating
this unit by TV remote control (the HDMI control function)” (p. 30) and “[HDMI Control]” (p. 35).
• For information on the output mode of the HDMI terminal,
refer to “[HDMI]” (p. 39).
• When no picture is displayed, refer to
“TROUBLESHOOTING” (p. 42).
Connection for the playback of Blu-ray
3D discs
You need the following equipment and connections to enjoy BD 3D discs on this unit: –a TV that has 3D functionality. – a TV and this unit must be connected with HDMI
cables.
– a BD disc should contain 3D images.
TV
VIDEO
AV INPUT
HDMI IN
1 2 3
(ARC)
OPTICAL
DIGITAL AUDIO OUT
2 Optical cable
(commercially available)
About audio return channel (ARC) supported TV
• You can connect an HDMI cable to the audio return
channel supported terminal (the terminal with “ARC” indicated) on the TV. In this case, you do not need to connect an optical cable.
• You need to activate the HDMI control function of this
unit so as to activate audio return channel (ARC) (
What is audio return channel (ARC)?
This function allows digital audio signal to be output from a TV to this unit through an HDMI cable, without using an optical cable.
y
If your TV is not ARC supported, connect the TV and this unit via the OPTICAL jack on the unit.
p. 35).
English
13 En
CONNECTION
USB PORTABLE
iPod/iPhone
Video connection
• Firmly connect the composite video cable (supplied) to the VIDEO jack.
• Refer to page 40 for information on the video output formats.
Notes
• If you play back the image via VCR, the image may deteriorate
due to the copy guard function.
• To enjoy BD 3D discs on this unit, you need to connect a TV
and this unit using HDMI cables (commercially available).
Connecting a satellite/cable TV tuner
You can connect a satellite or cable TV tuner that is not HDMI supported using a digital audio pin cable.
Connecting audio devices (such as a CD or MD player)
You can connect audio devices (such as a CD player, MD player, etc.) to the unit.
y
To connect a satellite or cable tuner to TV, you need extra video pin cables (commercially available).
Connecting a portable digital music player other than iPod
You can connect a portable digital music player other than iPod to the front panel of this unit.
PORTABLE
14 En
NETWORK AND USB CONNECTION
Connecting to the NETWORK terminal
• PC contents can be played back by connecting this unit to the network.
• You can enjoy a variety of contents with interactive functions by connecting to the internet when playing BD-Live compatible discs. Refer to page 27 for information on BD-Live functions.
Notes
• Firmly connect a network cable (commercially available) to the NETWORK terminal.
• Use only an STP (shielded twisted pair) network cable.
• When using the internet, a broadband internet connection as shown below is required.
• Connect the other connector of the network cable to the hub/broadband router.
• When using a broadband internet connection, a contract with an internet service provider is required. For more details, contact your
nearest internet service provider.
• Refer to the operation manual of the equipment you have as the connected equipment and connection method may differ depending on
your internet environment.
• Use a network cable/router supporting 10BASE-T/100BASE-TX.
PREPARATIONS
Connecting to the USB port
• You can connect a USB memory device (2 GB or greater and formatted with FAT 32/16) for BD Local Storage to the USB port on the rear panel (or front panel) of this unit to save the BD-Live data (p. 27) or to upgrade the software of this unit (p. 41).
• Firmly connect a USB memory device (commercially available) to the USB port.
CAUTION
• Do not remove the USB memory device or unplug the power
cable while the operations for BD-Live or software upgrade are being performed.
• Do not use a USB extension cable when connecting a USB
memory device to the USB port of this unit. Using a USB extension cable may prevent the unit from performing correctly.
Notes
• Yamaha cannot guarantee that all brands’ USB memory devices
will operate with this unit.
• For more notes on using USB memory devices, refer to
page 18.
This unit
To USB port
USB memory
device
(commercially
available)
y
To save BD-Live data on the USB memory device on the front panel, set [Local Storage] to [Front USB] (p. 35).
To NETWORK terminal
Network cable (commercially available)
To LAN terminal
LAN
Internet
Modem
After connecting
• When you set the Network setting manually, refer to “Network” (p. 36).
• To play back the PC contents on your network, refer to “Using network content” (p. 22).
Hub or
broadband router
PC
English
15 En
OTHER CONNECTION
Connecting the power cable
After all connections are completed, plug the supplied power cable into the AC IN on the rear of this unit. Then plug into AC outlet.
To AC inlet
To AC outlet
Note
TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT TOUCH THE UN-INSULATED PARTS OF ANY CABLES WHILE THE POWER CABLE IS CONNECTED.
16 En
OPERATIONS
INITIAL WIZARD/EASY SETUP
Setting with the Initial Wizard/Easy Setup
Initial Wizard/Easy Setup allows you to set language, resolution, and screen aspect ratio easily. Initial Wizard screen is displayed when you turn this unit on for the first time after purchase or upgrade. Same setting can be performed from SETUP menu = [System] = [Easy Setup] (p. 32).
1 When Easy Setup screen is displayed, press ENTER
to start Easy Setup.
2 Press 5/a to select the language you want to display
on the screen, then press ENTER.
4 Press 5 /a to select the screen aspect ratio, then
press ENTER. For details on setting items, refer to “[TV Screen]” (p. 37). Easy Setup is completed.
OPERATIONS
5 Press ENTER to exit Easy Setup.
3 Press 5/a to select the resolution, then press
ENTER. For details on setting items, refer to “[Video Out Select]” (p. 37).
Note
When you connect your TV and this unit via the VIDEO jack, select [Composite].
Notes
• When no picture is displayed after Initial Wizard/Easy Setup is completed, refer to “TROUBLESHOOTING” (p. 42).
• A warning message concerning 3D video playback appears when this unit is turned on. Press ENTER to dismiss the message or CLEAR to disable it (p. 35).
English
17 En
BASIC OPERATION
Follow the procedures below to play back the source.
1
Set the source
Disc
2 3
Switch the
input
Refer to the following pages for more
operations
USB
p. 20, 23
Front Rear
*1
USB PORTABLE
iPod/iPhone
DISPLAY
OPTION
TOP MENU
RETURN ON SCREEN
p. 15, 20
DIMMER
Network
(PC contents
and
YouTube*2)
p. 15, 22
1
*
· Some devices may not work properly even if they meet the requirements.
· Playability of and power supply to all kind of USB devices are not guaranteed.
· The reading time may exceed 30 seconds depending on the number of files/folders.
· Yamaha and suppliers accept no liability for the loss of data saved on the USB devices connected to this unit.
As a precaution, it is recommended that the files are made backup copies.
*2 Available for Russia and Asia models only.
STATUS
SETUP
HOME
ENTER
VOLUME
POP-UP MENU
TUNING
PRESET
18 En
iPod
USB PORTABLE
iPod/iPhone
BASIC OPERATION
2 3
1
Set the source
iPod/iPhone
USB PORTABLE
Switch the
input
*1
Refer to the following pages for more
operations
TUNING
STATUS
SUBTITLE
REPEAT
AUDIO
A B
PRESET
MEMORY
DIMMER
PIP
SHUFFLE
p. 12, 23
AUX
STB
Portable
TV
To AUX
p. 14
To COAXIAL
p. 14
p. 14
To output TV sounds, refer to page 13
for connection.
OPERATIONS
For details on operation, refer to the instruction manual supplied with the connected device.
FM
To receive FM radio stations, refer to page 28.
*1Some features may not be available depending on the model or the software version of your iPod.
English
19 En
BASIC OPERATION
Playing back photo/music/video
HOME and MEDIA menus allow you to browse and play multi-media files on data discs, USB memory devices and your network.
Note
For details on playable discs and files, refer to page 3.
Common operations for playing back files in a selected folder
Example: Selecting a movie file on a USB memory
device
Note
Stop the playback of the video before you move to MEDIA menu screen.
Basic operation
DISPLAY
SETUP
HOME
ENTER
OPTION
TOP MENU
2
RETURN ON SCREEN
HOME
ENTER
VOLUME
POP-UP MENU
5
a
5/a : Moves the focus. 2: Returns to the parent folder.
HOME: Moves to/exits HOME menu screen. ENTER: Confirms the folder/file.
Icons on the top of MEDIA menu
: Plays back the disc on the tray, or displays
contents in the data disc.
: Displays contents in the USB memory device
connected to the USB port.
: Searches for a DLNA (p. 22) server on the
network.
: Displays contents on the connected DLNA server.
1 Press HOME to move to HOME menu screen.
y
HOME menu screen may differ depending on the model.
2 Press 2/3 /5 to select [MEDIA], then press
ENTER. MEDIA screen appears.
20 En
3 Select the item which contains the file you want to
play back, then press ENTER.
BASIC OPERATION
4 Select the Photo, Music, Video or AVCHD folder
you want to play back, then press ENTER. To return to the parent folder, press 2 or select .
Note
Note that the only the file type selected on this step will be displayed in the following step. For example, if you selected the Photo folder in this step, only photo files are displayed after this step. When you want to play back other than photo, return to this step and select file type again.
5 Select the folder(s) containing the file you want to
play back.
6 Select the file you want to play back, then press
ENTER. When a video file is selected, playback starts. When a music file is selected, Status menu is displayed and playback starts. When a photo file is selected, slide show starts.
y
To enjoy a slide show with music, press HOME to return to HOME menu screen while music is played back, and select the photo file.
Note
The displayed file may not be played back depending on the content.
OPERATIONS
Operations for viewing photos
While viewing photos, the buttons on the remote control work as shown below.
: Stops a slide show and returns to the file browser. : Pauses a slide show. : Plays a slide show. : Moves to a next photo. : Moves to a previous photo. : Makes a slide show faster in 3 steps. : Makes a slide show slower in 3 steps.
5 : Inverts a photo. a : Reflects a photo. 2 : Rotates a photo counterclockwise. 3 : Rotates a photo clockwise.
ZOOM: Zooms in/out a photo (zoom in/out: 3 steps each).
5/a /2 /3 : Pans in zoom mode when a photo is larger than the screen.
DIGEST: Switches to thumbnail mode (p. 6). When thumbnails are displayed, you can proceed to the next/ previous page with / .
English
21 En
BASIC OPERATION
Using network content
About DLNA
This unit is a DLNA certified digital media player. You can manage photo, music and video contents stored on DLNA servers on your home network. DLNA (Digital Living Network Alliance) provides easy sharing of digital media through network in the home, and you can enjoy digital contents stored on your DLNA­server-software-installed PC or other DLNA compatible device with your TV via this unit. To connect this unit to your DLNA servers, some settings for the DLNA server or device are required. For details, refer to your DLNA server software or DLNA device.
Playing back shared contents
Note
To play back files on your PC, install a DLNA server software, such as Windows Media Player 12, and share files you want to play back.
1 Turn on the PC with DLNA server software installed
or the DLNA device connected to your home network.
2 Press HOME to display HOME menu screen, then
select [MEDIA] to move to MEDIA menu. The DLNA servers connected to the network are listed on the screen.
3 Select the file you want to play back.
Notes
• The playback and operating quality may be affected by your
home network condition.
• The files from removable media, such as USB memory devices
or DVD-drive on your media server, may not be shared properly.
Using network services
You can instantly watch the videos that the following network services provide. – YouTube
Notices for network services
• Access to content provided by third parties requires a
high speed internet connection and may also require account registration and a paid subscription.
• Third party content services may be changed,
suspended, interrupted, or discontinued at any time without notice, and Yamaha disclaims any liability in connection with such occurrences.
• Some content may only be available for specific
countries and may be presented in specific languages.
• Yamaha does not represent or warrant that content
services will continue to be provided or available for a particular period of time, and any such warranty, express or implied, is disclaimed.
Notes
• If your DLNA server is not listed, select [DLNA Search] to find it.
• Depending on the DLNA server, this unit may need to be permitted from the server.
• To play the file on the DLNA server, this unit and the server must be connected to the same access point.
• The file requirements may not always be compatible. There may be some restrictions depending on file features and DLNA sever capability.
Playing videos from YouTube™
You can watch movies from YouTube over the internet using this unit. The services may be changed without notice.
1 Press HOME to display HOME menu screen.
y
HOME menu screen may differ depending on the model.
2 Press 5/a /2 /3 to select [YouTube], then press
ENTER.
y
To return to HOME menu screen, press RETURN.
22 En
Operation for iPod
RETURN ON SCREEN
PIP
SUBTITLE
AUDIO
MEMORY
SHUFFLE
REPEAT
DIMMER
STATUS
TUNING
PRESET
A B
VOLUME
SETUP
DISPLAY
HOME
OPTION
ENTER
TOP MENU POP-UP MENU
BASIC OPERATION
Repeat play
You can repeat playback as you want.
You can operate playback of your iPod by using the buttons on the remote control.
DISPLAY
,
REPEAT
SHUFFLE
,
,
Note
Some features may not be compatible depending on the model or the software version of your iPod.
Playback controls
1 Press any buttons below during playback.
: Stops playback. : Pauses playback. : Skips forward. : Skips backward.
To start/resume playback, press .
y
Press DISPLAY to display information below on the front panel display during playback.
• Song name
• Artist name
• Album name
1 Press REPEAT repeatedly for repeat play.
Each press cycles as follows:
Operation for CDs
You can also operate playback of music for CDs.
Playback controls
1 Press any buttons below during playback.
: Stops playback. : Pauses playback. : Skips forward. : Skips backward. : Searches forward. : Searches backward. : Press for instant search. Instant search skips the
music 30 seconds.
: Press for instant replay. Instant replay replays the music from 10 seconds before. To start/resume playback, press .
y
You can also use the Numeric buttons to enter the number of the song directly. To clear the entry, press CLEAR.
Shuffle play
You can play back in random sequence.
1 Press SHUFFLE repeatedly for shuffle play.
Each press toggles as follows:
OPERATIONS
Note
There are some characters that cannot be displayed on the front panel display of this unit.
Shuffle play
You can play back in random sequence.
1 Press SHUFFLE repeatedly for shuffle play.
Each press cycles as follows:
*1You cannot set ALBUMS when you use an iPod touch and
iPhone.
Repeat play
You can repeat playback as you want.
1 Press REPEAT repeatedly for repeat play.
Each press cycles as follows:
English
23 En
ADVANCED PLAYBACK OPERATION
This chapter explains playback of commercially available BD/DVD/CD discs, and recorded DVD-RW/R discs.
Note
For the basic playback operation, refer to page 6.
On Screen menu
To display On Screen menu, press ON SCREEN. After that, press 5/a /2 /3 to select an item, then press ENTER to operate the desired function.
On Screen menu contains following items.
Title : Shows the title number being
BD DVD VIDEO
played back. You can skip to the desired title by selecting it from this item.
Chapter : Shows the chapter number being played back. You can skip to the desired chapter by selecting it from this item.
Track/File : Shows track/file number being played back. You can skip to the desired track/file by selecting it from this item.
Time : Shows the playback time. Select display type from the following:
Mode/Play Mode
DVD CD VIDEO MUSIC PHOTO
playback mode. You can select playback mode from the following:
CD
BD DVD VIDEO
CD VIDEO MUSIC PHOTO
BD DVD CD VIDEO MUSIC
– Elapsed playback time of the title, chapter, disc,
track or file.
– Remaining playback time of the title, chapter, disc,
track or file.
: Shows current
–Normal: Normal playback. – Shuffle: Random playback without repetition. – Random: Random playback with repetition.
DVD
– Normal – Shuffle CH (chapter) – Shuffle TT (title) – Shuffle All – Random CH (chapter) – Random TT (title) – Random All
VIDEO MUSIC PHOTO
– Normal – Shuffle F (folder) – Random F (folder)
Audio : Shows audio language/
BD DVD VIDEO
signal of a BD/DVD disc currently selected. You can select the desired type of audio.
Angle : Shows the currently-selected angle
BD DVD
number. If the video is recorded with multiple angles, you can change the angle.
y
When the Angle Mark ( ) is set to [On] (p. 36), is displayed on the screen when this function is available.
Subtitle : Shows the currently-
BD DVD VIDEO
selected subtitle language when the subtitle is provided.
Subtitle Style : Shows the currently-selected
BD
subtitle style. This function is available only for Video-file external subtitle. You can select the desired text style of subtitle.
Bitrate : Shows
BD DVD CD VIDEO MUSIC
bitrate of the audio/video signal.
Second Video : Turns the PIP on/off (p. 6).
Second Audio : Turns the secondary audio on/off.
BD
BD
Ins Search
: Skips 30 seconds.
BD DVD CD VIDEO MUSIC
Ins Replay
: Replays the content
BD DVD CD VIDEO MUSIC
from 10 seconds before.
Slide Show :
PHOTO
Shows slide show speed. You can select the slide show speed from Slow/Medium/Fast.
Transition : Shows how photo appears on the
PHOTO
screen. You can select the transition type.
24 En
ADVANCED PLAYBACK OPERATION
Status menu
This shows various settings, such as subtitles, angle settings and the title/chapter/track number currently played back. To display Status menu, press STATUS. Status menu contains following menus.
BD DVD VIDEO
Example: Icons when playing a BD disc
13
2465
78
1 (Playback status)
2 (Disc type/video file icon)
CD MUSIC
Example: Icons when playing a music file
1 (Playback status) 2 (Repeat mode): Shows current repeat mode
(p. 6).
3 (Disc type/music file icon)
4 (Artwork) : Displays artwork if the file
contains it.
MUSIC
OPERATIONS
3 (Title number being played): You can jump to
specified title with SEARCH button (p. 7).
4 (Chapter number being played): You can
jump to specified chapter with SEARCH button (p. 7).
5 (Subtitle currently selected): You can change
the subtitle language with SUBTITLE button (p. 6).
6 (Elapsed playback time): You can jump to
specified point with SEARCH button (p. 7).
7 (Audio currently selected): You can change the
audio language or format with AUDIO button (p. 7).
8
(p. 6).
(Repeat mode):
Shows current repeat mode
5 (Track/file number being played): You can
jump to specified track with SEARCH button (p. 7).
6 (Information) : Displays music information
if the file contains them.
7 (Elapsed playback time): You can jump to
specified point with SEARCH button (p. 7).
8 (Progress bar) : Shows progress status of
current song.
PHOTO
Example: Icons when viewing a photo file
1 (Playback status)
2 (Photo file icon)
3 (File number being displayed)
4 (Repeat mode): Shows current repeat mode
(p. 6).
5 (Slide show speed)
MUSIC
MUSIC
English
25 En
ADVANCED PLAYBACK OPERATION
Using Bookmark
This allows you to set Bookmark at the specified point of the video. After Bookmark is set, you can move to the point you set using this function. You can set up to 12 Bookmarks.
DVD VIDEO
Example: Setting Bookmark when playing back a movie.
1 Press MARKER during playing back the movie to set
Bookmark. Bookmark number and the status are displayed.
2 After Bookmark is set, press DIGEST to display
Bookmark select bar.
3 Press 2/3 to select the Bookmark you want to play
back, then press ENTER. Press CLEAR to delete the selected Bookmark.
Note
When playback is finished (e.g., ejecting the disc, pressing twice), Bookmarks are automatically deleted.
2 Press ENTER to program playback order.
For audio disc, press 5/a to select a desired track, then press ENTER. For DVD-Video discs, select a desired title (shown as TT) and chapter (shown as CH) instead of a track. To clear a set track, select the track you want to clear, then press CLEAR. Press RETURN to cancel the Program play.
3 After programming is finished, press to set and
start program playback.
4 To cancel program play, stop playback completely by
pressing twice.
Using search
Program play
This allows you to program playback order of audio disc tracks or DVD chapters. You can program up to 15 tracks/chapters.
DVD CD
Example: Programming the playback order of CD tracks
1 Press PROGRAM during playback to display
PROGRAM screen.
This allows you to jump to the specified point during playback.
BD DVD CD VIDEO MUSIC
Example: Searching to the specified point
1 Press SEARCH during playback. Status bar appears. 2 Press 5/a /2 /3 to select one of the item below,
then press ENTER.
:
BD DVD
– Title number (shown as ) – Chapter number (shown as ) – Elapsed title time (shown as ) – Elapsed chapter time (shown as )
:
CD
– Track number (shown as ) – Elapsed track time (shown as ) – Elapsed disc time (shown as )
:
VIDEO MUSIC
– File number (shown as ) – Elapsed file time (shown as )
26 En
ADVANCED PLAYBACK OPERATION
3 Press 5/a or number buttons to set/adjust the value
of the focused item, and press ENTER to jump to the specified point.
4 To close the status bar, press STATUS.
Enjoying BONUSVIEW™ and BD­Live™
This unit supports BONUSVIEW (p. 50) (BD-ROM Profile 1 Version 1.1) and BD-Live (p. 50) (BD-ROM Profile 2) playback functions.
Note
Functions and playback method vary depending on the disc. Refer to the guidance on the disc or the supplied user’s manual.
Using Picture in Picture function (secondary audio/video playback)
BD-Video that includes secondary audio and video compatible with Picture in Picture can be played back with secondary audio and video simultaneously as a small video in the corner.
Primary video Secondary video
1 While PIP Mark ( ) or Secondary Audio Mark
( ) is displayed, press PIP to turn the Picture in Picture function on/off.
Notes
• To listen to secondary audio from a TV connected with an
HDMI cable, make sure that the Audio Output setting (HDMI) is set to [PCM] (p. 39).
• Depending on the disc, to listen to secondary audio, you may
need to set secondary audio to on from the top menu of the disc (p. 8).
• The secondary audio and video for Picture in Picture may
automatically play back and be removed depending on the content. Also, playable areas may be restricted.
Using the feature of BD-Live™
1 Set the Network setting (p. 36). 2 Connect the USB memory device to this unit (p. 15).
• BD-Live data is saved in a USB memory device connected to this unit.
• Connect a USB memory device (2 GB or greater and formatted with FAT 32/16) supporting USB
2.0 High Speed (480 Mbit/s) to the USB port that you select on Local Storage (p. 35). The default setting is the USB port on the rear panel.
• A “BUDA” folder is created automatically in the USB memory device when necessary.
• If there is insufficient storage space, the data will not be copied/downloaded. Delete unneeded data or use a new USB memory device.
• Some time may be required for the data to load (read/write).
3 Play back the disc. 4 Run BD-Live according to the instructions on the
disc.
Notes
• Regarding playback method of BD-Live contents, etc.,
perform the operations in accordance with the instructions in the BD disc manual.
• To enjoy BD-Live functions, perform the network
connection (p. 15) and Network settings (p. 36).
• Refer to “[BD-Live Connection]” (p. 36) regarding the
setup to restrict access to BD-Live contents.
• The time required to download the provided programs into
the USB memory device connected to this unit varies depending on the internet connection speeds and the data volume of the programs.
• BD-Live programs provided through the internet may not
be able to display the connection depending on the status (upgrading) of the provider. In such cases, take out the disc and try again.
• If the BD-Live screen does not appear for a while after
you select the BD-Live function in the BD disc menu, the USB memory device may not have enough free space. In such cases, eject the disc from this unit, and then erase the data in the USB memory device selecting [Format] in [Local Storage] (p. 35).
OPERATIONS
27 En
English
LISTENING TO FM RADIO STATIONS
Tuning to radio stations
TUNING
MEMORY
TUNER
PORTABLE
<<, >> (TUNING)
TUNER
STATUS
SUBTITLE
REPEAT
TV
USB NET
PRESET
AUDIO
A B
STB
AUX
DIMMER
PIP
SHUFFLE
iPod
DISC
1 Press TUNER. 2 Press and hold << / >> (TUNING).
Automatic tuning starts.
y
If the signal received from the station you want to select is weak, you can also tune into radio stations manually by pressing << / >> (TUNING) repeatedly. In this case, the sound will be monaural.
Presetting radio stations
Manual preset tuning
1 Select a favorite radio station by pressing << / >>
(TUNING).
2 Press MEMORY. 3 Select the preset number you want to store to by
pressing 5/a or < / > (PRESET).
4 Press ENTER.
The manual preset is complete.
y
• You can preset up to 30 FM stations.
• To cancel the manual preset while choosing a preset number,
press MEMORY again.
• You can delete a preset station by pressing OPTION ENTER to select [PRESET DEL] (p. 29).
Selecting preset radio stations (Preset tuning)
You can store your favorite FM stations with the preset function.
HOME
OPTION
<, > (PRESET)
OPTION
TOP MENU
RETURN ON SCREEN
DIMMER
PIP
ENTER
STATUS
SUBTITLE
AUDIO
POP-UP MENU
TUNING
PRESET
MEMORY
5
ENTER
a
<<, >> (TUNING)
MEMORY
Automatic preset tuning
1 Press and hold MEMORY for more than 3 seconds in
FM mode.
2 Press ENTER.
Start the automatic preset.
Note
When you perform the automatic preset, all stored stations are cleared and the new stations are stored.
TUNING
STATUS
SUBTITLE
AUDIO
PRESET
MEMORY
<, > (PRESET)
DIMMER
PIP
1 Select the preset radio station in FM mode by
pressing < / > (PRESET).
y
You can also use the Numeric buttons on the remote control or < / > (PRESET) on the front panel of this unit to select the preset
radio station.
28 En
Loading...
+ 195 hidden pages