Yale 7110, 7110F, 7170LBR, 7170FLBR Installation Instructions Manual

7110(F), 7170(F)(LBR)

Surface Vertical Rod Exit Device Series

Installation Instructions

Strike Angle Must

Shim (2) Supplied

Strike Plate

Engage Strike

726
Top Strike

Top Mounting Plate

(2) 1/4-20 X 3/4" PFHMS

(Metal Door)

or

(2) #14 x 1-1/2" PFH”AB”SMS

(Wood Door)

Rod Guide

(2) #8 x 1/2" (13mm) PRH”AB”SMS

Top Rod

Roll Pin

Bottom Rod Assembly

Rod Guide

(2) #8 x 1/2" (13mm) PRH”AB”SMS

Bottom Mounting Plate

(2) 1/4-20 X 3/4" PFHMS

(Metal Door)

or

(2) #14 x 1-1/2" PFH”AB”SMS

(Wood Door)

790 Strike

791 Strike

(3) 10-24 x 3/4" (19mm) PFHMS

Top Latch

(Panic & Fire Label)

(3) 10-24 x 1/4" (6mm) PPHMS

(2) 8-32 x 1/4" (6mm) PFHMS

Latch Cover

(2) #6 x 3/8" (10mm) PTH”AB”SMS

‘

Guide Cover

Top Rod Connector

(2) 1/4-20 X 1" PPHMS

(Metal Door)

or

(2) #14 x 1-1/2" PPH”AB”SMS

(Wood Door)

(2) 8-32 x 5/16" (8mm) PFHUMS

(2) #6 x 3/8" (10mm)

ABBREVIATION

PTH”AB”SMS

Guide Cover

Deadbolt

Bottom Bolt Case
Panic & Fire Label

(3) 10-24 x 1/4" (6mm)
PPHMS

(2) 8-32 x 1/4" (6mm) PFHMS

Bolt Case Cover

12-24

PRHMS

Top bracket and 726 strike
required for 7170(F)(LBR).

End Clamp

(3) 8-32 x 5/16"

PFHUMS

End Cap

(2) 1/4-20 X 1" PPHMS

(Metal Door)

(2) #14 x 1-1/2" PPH”AB”SMS

or

(Wood Door)

Hole Plug

(Fire Label Devices)

Dogging Key

Dogging

Feature to hold bolts retracted and

touchpad depressed, for push-pull door

To Dog Device

1. Insert dogging key.

2. Hold touchbar depressed.

3. Turn key 1/4 turn clockwise.

(Not a feature of fire labeled devices.)

Cover

FASTENER DESCRIPTION

PPH”AB”SMS

PFHUMS

PFHMS

PRH”AB”SMS

PTH”AB”SMS PHILLIPS TRUSS HEAD TYPE “AB” SHEET METAL SCREW

PPHMS PHILLIPS PAN HEAD MACHINE SCREW

PFH”AB”SMS

PRHMS PHILLIPS ROUND HEAD METAL SCREW

PHILLIPS PAN HEAD TYPE “AB” SHEET METAL SCREW

PHILLIPS FLAT HEAD UNDER CUT MACHINE SCREW

PHILLIPS FLAT HEAD MACHINE SCREW

PHILLIPS ROUND HEAD TYPE “AB” SHEET METAL SCREW

PHILLIPS FLAT HEAD TYPE “AB” SHEET METAL SCREW

All dimensions are in inches (mm) unless otherwise noted.

operation.

An ASSA ABLOY Group brand

80-9470-0010-000 (03-13)

To Change Hands

Maintenance

RHR Device

Vertical Lifter Assembly

(4) 8-32 x 3/16" PPHMS

Remove (4) Screws and
Vertical Lifter Assembly.
Rotate device to opposite
hand (180 degrees). Insert
Lifter Assembly under Lift
Block and re-install screws.

Lift Block

Vertical Lifter Assembly

(4) 8-32 x 3/16" PPHMS

LHR DoorRHR Door

Check Before Starting

Unreinforced Doors or Frames

Doors and Frames with walls having a structural
thickness (metal skin plus reinforcement or solid
hardwood) to engage less than (3) full screw threads
are considered unreinforced.

Unreinforced Doors: Use SNB (sex nuts and bolts).

Unreinforced Frames: Use Blind Rivet Nuts.

Recommended fasteners for unreinforced openings
are not necessarily supplied by Yale Locks and
Hardware.

LHR Device

1. Periodically remove covers and coat mechanisms with a

silicone base lubricant. This is particularly required in corrosive
environments for proper product function.

2. Check mounting fasteners periodically. Retighten if found
loose. Apply screw locking compound (available at automotive
part stores) or change part fasteners if screws continue to back
out.

3. Periodic checks (and adjustments) of strikes are required to
compensate for changes in the opening (e.g. door sagging).

Min. Door Stile

4-1/2" (114mm)

Door and frame must
meet structural and
dimensional specifications
on exit device template(s)
for door and frame
preparation.

Reinforcement

Door Skin

Blind Rivet Nut

Door Must Swing Freely

1. Mark Door

Single Door or Pair without Mullion

Locate and Mark Horizontal and Vertical Reference Centerlines as shown.

LHR door shown, preparation is typical for both door hands.

Note: Door should be in the closed position while marking horizontal and
vertical reference lines. Paper or the Plastic Template may be used in this step.

FINISHED

FLOOR

or THRESHOLD

2. Prepare Door, Frame, & Sill

A. Locate “Device Template” aligning VERTICAL REFERENCE and HORIZONTAL

REFERENCE lines. Tape template to door face.
B. Extend centerline of Rod and Strikes from “Device Template” to door top and
bottom, on door face.
C. Locate Top Latch/Strike and Bottom Bolt Case templates in place over centerline
of Rods and Strikes on door. Tape templates in place and mark holes.
Note that the centerline of the rods and strikes used to install top and bottom bolts
is not the Vertical Reference centerline.

D. Locate and tape Trim Template to door when required (See instructions packed with Trim).
E. Mark and prepare holes per installation template (exclude 791 or 726 strike, holes

prepared in Step 7).
F. Locate 790 Bottom Strike Template. Tape in place over Rods and Strikes centerline
on door. Tape template in place and mark hole locations. Holes to be prepared in Step 7.
G. Remove templates from door.

op Latch & 791or 726

T

LHR DOOR
INSIDE FACE

VERTICAL
REFERENCE

HORIZONTAL

39-15/16

(1014)

emplate

ike T

Str

Device Template

Bottom Case

Template

Floor Strike Template

FINISHED FLOOR or THRESHOLD

REFERENCE

LHR DOOR
INSIDE FACE

Rods & Strikes

VERTICAL
REFERENCE

HORIZONTAL
REFERENCE

2

An ASSA ABLOY Group brand

80-9470-0010-000 (03-13)

3. Size Device

Device must be field cut to size, as required

* LHR Door (Door Open)
inside face

STILE

Horizontal line

C

L

Dogging
Hole

4. Mount Device & Components

Note: 726 Strike and top

bracket not shown.

Top

Mounting

Plate

Top

Latch

16-3/8

(416)

791 Strike

D

1-3/8
(35)

3/8

(10)

HINGE SIDE OF DOOR

Min.

Min.

CUT
LINE

STOP
SURFACE

2-1/4
(57)

Determine device length

1. Close door. Measure 2-1/4" (57mm)
from the Stop Surface on the hinge side of
the door, mark Horizontal Reference at
this point.

Note: This dimension must be 3/8"
(10mm) minimum from edge of the stile
on the door.

2. Open door. Align mounting holes in
device with Mounting Holes in the door.
Mark device where it crosses the mark
from Step 1. If mark is less than 1-3/8"
(35mm) min. from Dogging Hole, a shorter
device is required.

3. Before cutting, make sure the End
Cover is in place and there is no gap
between it and the Pushpad. Cut device
on mark from Step 2.

(2) 1/4-20 x 3/4" (19mm)
PFHMS

F

C

L

B

C

Device Mounting Holes,

L

Rods, & Strikes

Rod Guide

F

15

(381)

D

Bottom Bolt

Case

790 Strike

Rod Guide

Bottom

Mounting

(3) 10-24 x 1/4" (6mm)
PPHMS

Plate

(2) 1/4-20 x 3/4" (19mm)
PFHMS

Bottom Bolt

Case

End
Clamp

C

1/2

vice

De

(3) 10-24 x 1-1/4" (32mm)
PPHMS

(13)

Figure 3.

An ASSA ABLOY Group brand

3

80-9470-0010-000 (03-13)