Page 1
da Vinci Super
Quick Guide
Safety Precautions
Product instructions
Unboxing and Installation
Product specication
Function Operation and Instructions
Setting
Print
Supporting information
ENG
da Vinci Super 3D printer
September . 2017
da Vinci Super
Page 2
P 2
da Vinci Super 3D printer
da Vinci Super
The manual is mainly intended for users to understand how to use the da Vinci Super 3D printer (“da Vinci Super”)
correctly. In this manual, users can learn more about the operating tips, application skills and maintenance of the da Vinci
3D printer.
For more information on the da Vinci Super 3D printer and the complete XYZprinting product line, please contact your
local dealer or visit the ofcial website of XYZprinting: http://www.xyzprinting.com.
Safety Precautions
Safety and Compliance
Important Safety Precautions
Please read through this manual and all safety precautions carefully before using, operating, unpacking, replacing,
removing any part or maintaining this product. Please also comply with the instructions of relevant safety
precautions.
●
●
Do not move the machine by yourself as it is heavy.
Do not place the printer on a soft or tilted surface. Otherwise, the machine will fall / ip over and become
damaged or cause personal injury.
Do not place the printer in a dusty, humid or outdoor environment.
Weak odors may be generated during the printing process. We recommend working in a well-ventilated
and open area to ensure operational comfort.
Do not leave the product or power cord to unattended children. Otherwise, personal injury or electric
shock might occur.
Use the provided power cord. Otherwise, incorrect grounding might lead to damage.
Do not place any liquid container on top of the product. Otherwise, overow or spill might go into the
machine and pose the risks of danger or safety concern.
Do not wipe the printer with alcohol or ammable chemicals. Otherwise, danger might occur.
Do not move the machine when it’s powered on.
Do not reach into the machine with your hands during operation. Otherwise, risks of impact from moving
printing parts or burn from high temperature might occur.
The machine becomes hot during operation and thus run in high temperature. Do not touch or replace
parts when they are not cooled down.
After startup, the parts in the machine will heat up or move depending on the user’s instructions. During
product operation, do not touch or block the operation of the parts.
Defect reparation must be carried out according to the contents of this instruction manual. Where the
defect cannot be repaired, please contact your printer dealer or the customer service center.
Trademarks
All trademarks and registered trademarks are the properties of their respective owners.
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Page 3
P 3
da Vinci Super 3D printer
da Vinci Super
Scraper
Print head cleaning wirewire
Feed hole cleaning wire Wire brush Gear cleaning brush
Product instructions
Accessory List
●
①
5” color touch panel
②
Rear feeding motor
③
Print bed
④
Filament holder
⑤
Print head
⑥
Power inlet
⑦
USB socket
⑧
Power switch
⑨
USB Port
Precautions and Instructions of Maintenance Tools
Maintenance and Service
●
The following maintenance tool shall only be used with adult guidance or supervision. To prevent accidents,
do not allow a child to access maintenance tools without proper training.
• Make sure the maintenance work of the printer is carried out when the printing bed is cooled down.
• Filament residues generated during the course of printing may be stuck on the print head and gears of the printing module. The printing quality and
printer operation as well as the measurement of the printing bed may be affected. When this happens, clean the printing module with the wire brush.
• When printing is completed and the printing bed is cooled down to room temperature, the printed object can be removed from the printing bed with
the scraper.
When the printer needs to be serviced during the term of the warranty, it is recommended that the machine is packed with original packaging
materials prior to shipment. For this purpose, the packaging materials are better to be kept. If other packaging materials are used instead,
the printer might be damaged during printing. We reserve the right to assess relevant service fees.
2
7
8
9
6
USB drive
(including XYZware Pro installer,
da Vinci SUPER user manual and
XYZware Pro user manual)
Filament guide tubePLA lament Power cord USB cable
Front-feeding motor Wireless
Top cover
Mask tape
● ●● ● ●
● ●
●
●
1
2
4
3
5
Page 4
P 4
da Vinci Super 3D printer
da Vinci Super
Unboxing and Installation
1
3
6
9
12
2
4
7
10
13
5
8
11
Remove the plastic wrap and PP strap.
Remove the top cover box and the
packaging materials.
Place the printer on a table or platform
(please do not move the printer alone).
Remove the cable tie and foam situated
behind the front door.
Plug-in the power cord
Remove the top cover.
Remove the side of the carton .
Remove all tape from the body (4
pieces in total).
Insert the guide tube through the
top cover, and then insert one end
into the extruder module.
power on the printer.
Remove the assessory box.
Remove the foam next to the guide
screws on both sides, and then remove
the foam under the print bed. (total 4
pieces)
Insert the other end of the guide
tube into the feed module and
secure it tightly.
Page 5
P 5
da Vinci Super 3D printer
da Vinci Super
Product specication
Printing technology
Dimensions (W*D*H)
Gross weight
Printing dimensions (W*D*H)
Print resolution
Automatic feed system
Printing bed heating
Automatic printing bed calibration
Print head diameter
Print material
Language
Connection method
Printing software
File format
Operation System
FFF (fused lament fabrication)
511*581*670 mm
35.5kg
Front-feeding motor: 290 x 290 x 300 mm
Rear-feeding motor: 300 x 300 x 300 mm
0.02 - 0.4 (mm)
Yes
Yes
Yes
0.4 (mm)
ABS / PLA / TPE / Tough PLA / PETG , open-lament
Multi language
USB 2.0 / Wi-Fi
XYZware Pro
.stl / .3w
Windows 7+ / Mac OS X 10.10 to 10.12
Page 6
P 6
da Vinci Super 3D printer
da Vinci Super
Function Operation and Instructions
USB printing
●
1. Check if the USB drive is plugged to the machine.
2. Tap the USB Printing Menu in the main screen.
3. Select the le (.3w le) to print.
4. Check le information and tap “PRINT”.
Page 7
P 7
da Vinci Super 3D printer
da Vinci Super
Loading the filament
●
1. Remove the side cover and place the lament on
the side of the machine.
2. Tap Filament Load and Unload in the main screen.
4. Conrm the operation.
7. Once the print head extrudes lament in a continuous thread,
loading is complete. After the lament is loaded, tap to conrm.
5. Insert the lament into the auto-feed module.
3. Tap Load.
6. The print head will pre-heat until it reaches 240°C
(XYZprinting PLA).
Once the set temperature is reached, the feeding motor will
feed the lament along the guide tube into the print head.
Page 8
P 8
da Vinci Super 3D printer
da Vinci Super
Unloading the lament
●
1. Tap Filament Load and Unload in the main screen.
3. Conrm the unloading operation.
5. When the unloading operation is complete,
tap to conrm.
2. Tap “Unload” and conrm the operation.
4. Once the print head pre-heating reaches 240°C,
the feeding motor will unload the lament.
Page 9
P 9
da Vinci Super 3D printer
da Vinci Super
Filament Installation (Rell)
●
1. Tap the icon when printing.
3. The nozzle will be preheated and the lament will be unloaded
automatically.
5. The nozzle will be preheated and the machine will notify you when to insert lament into the feed module.
6. Check if lament has been extruded from the nozzle, after conrmation, the printer will resume printing.
4. Replace the empty spool with a new one.
(please refer to the LOADING section in this
manual) and then tap "PROCEED".
2. Tap Rell Filament and then tap Rell.
da Vinci Super will prompt you to rell material.
Page 10
P 10
da Vinci Super 3D printer
da Vinci Super
Temperature settings
Auto-detection (Auto)
Manual settings (Manual)
●
●
●
da Vinci Super allows the user to use different materials or third party laments. To satisfy the parameters or
characteristics of various laments, da Vinci Super allows the user to manually adjust extruder temperature,
printing bed temperature, and lament unloading temperature.
The printer will automatically read the NFC chip provided on the XYZprinting lament spool to automatically
adjust extruder temperature, printing bed temperature, and lament unloading temperature.
You can adjust the nozzle temperature, print bed temperature and nozzle unloading temperature, to suit you
lament type.
Print Bed
Temperature range 40~100
℃
170~300
℃
170~300
℃
Nozzle
Unloading
Page 11
P 11
da Vinci Super 3D printer
da Vinci Super
Calibration
Print-Bed
●
1. Select Calibration.
1. Select Print Bed.
3. The calibration starts. The printing bed goes up. The print head will move to the three testing points and
measure them in order. Once the measurement is completed, the motor under the print bed will automatically
adjust the print bed level.
4. After the calibration is successfully completed, tap to conrm.
2. Conrm the operation
Settings
1
2
3
Page 12
P 12
da Vinci Super 3D printer
da Vinci Super
Z-offset
Jog Mode
●
When the printing bed is calibrated, perform the vertical calibration of Z-OFFSET to ensure the print head can
eject onto the printing bed smoothly.
The jog mode is a function which allows you to control the position of the print head and the printing bed manually.
How to move the print head:
Return to the Home point. Always return to the Home point
prior to any movement in any direction.
Move in the X axle direction.
Move in the Y axle direction.
Move in the Z axle direction
Home position.
1. It is recommended that the space between the print head and the print bed just touch and the nozzle can move
smoothly on the print bed.
2. Users can tap the icon to raise or lower the print bed, the higher the value, the bigger the distance and vice versa.
3. After the adjustment is completed, tap Check to save the settings.
1 2 3 4
1
2
3
4
Page 13
P 13
da Vinci Super 3D printer
da Vinci Super
Clean Nozzle
Print-Head
●
1. Select the Clean Nozzle function and conrm the selection.
Before cleaning the extruder nozzle, rst make sure that the lament has been unloaded and that the Guide
Tube has been removed.
2. The print bed will be lowered and the
print extruder will move to a position
slightly in front of the center.
When the temperature of the print head reaches the operating temperature, the cleaning operation starts.
(Note: do not touch the metal part of the print head as it becomes hot during the operation.)
Inset the feed hole cleaning wire into the feed hole
and push it downwards to drive out the lament
from the print head.
(It is recommended that the operation is performed
from the top of the machine.)
Use the tweezer to hold the extruder
cleaning wire, and insert the wire from the
bottom of the extruder to clear the extruder
opening.
Remove the lament residues from the
print head with a wire brush.
After the cleaning operation is completed,
tap DONE.
1
3
2
4
Page 14
P 14
da Vinci Super 3D printer
da Vinci Super
Nozzle replacement.
1. Tap the Change Nozzle option.
3. Wait until the print head moves to a proper position
for change.
5. Turn off the power before change the print head.
7. Press the white release button to separate the
print head.
Installation sequence of new print head:
1. Connect the bus (make sure it clicks into place)
2. Press the white release button on the print head and assemble the print head and the mechanism. After the assembly,
check if the print head is secured without shaking.
3. Turn on and use the printer.
8. Hold the print head with one hand and remove the bus with
the other. The removal of the print head is complete.
2. Check if replacement is necessary. Tap Check to replace it.
4. The position of the print head change is shown as below.
6. Change the print head from above the machine.
In order to print a wide range of different materials, the
da Vinci super has a fan duct attached to its extruder
module. This can be opened and closed depending on
your lament type.
PLA & PETG : Close
ABS & TPE : Open
Page 15
P 15
da Vinci Super 3D printer
da Vinci Super
Wi-Fi
●
Preparations before printing
Add connected device (Add)
Network printing function mainly allows the use of an Intranet. Connect both the printer and computer within the same network
domain. In other words, both must be connected to the same wireless access point.
XYZware Pro must be used to verify wireless communication functions. Before setting up the network printing function, make
sure that the latest XYZware Pro has been installed on your computer.
Adjust the settings of the connected wireless access point before connecting the printer. For settings on the details, refer to the
user manual or information from the original manufacturer on the product.
The wireless printing only supports 2.4 GHz and requires a channel width of 20 MHz. For information on adjusting the channel
width, refer to the instruction manual from the original manufacturer of the wireless access point.
Make sure that the wireless network function is switched on.
The printer supports the following safe connection modes. When setting up printer connections, enter information for the sharing
key when required.
1. Select Wi-Fi.
3. Tap the access point to be used.
4. Enter the password required to connect to the
wireless access point.
5. Conrm the successful connection by selecting the conrmation
sign. The printer will be successfully connected to the wireless
access point at this point.
2.
Tap ADD and the printer will start to search for available access points.
●
●
●
●
●
●
Page 16
P 16
da Vinci Super 3D printer
da Vinci Super
Language
●
Change language settings
The da Vinci Super provides eight display languages, including
traditional and simplied Chinese, English, Japanese, German,
Italian, Spanish and French. The language setting can be
changed by tapping Settings > Languages in the main screen.
1. Open XYZware. Select the Printer Monitor button at the lower right corner of the interface.
2. Select Connect by IP and then enter the IP address of the printer. To check the IP, use the IP Address (PRINTER)
function on the printer control panel.
3. Conrm the connection. The printer is now able to receive les to be printed through a Wi-Fi connection.
Conrming the connection in XYZware Pro
Page 17
P 17
da Vinci Super 3D printer
da Vinci Super
Print
Transfer les to be printed via the PC software “XYZware Pro”
●
Connect the printer and computer with a USB cable and install the “XYZware Pro” on the computer
to transfer the les you want to print.
XYZware Pro can be used with Windows 7, Mac OSX 10.10 or later versions of the operating systems. You can also use
the original manufacturer’s USB provided with the printer to install XYZware Pro or download installation les from the
ofcial website.
Visit the ofcial website for details: http://www.xyzprinting.com/
Select Import and choose the model les to print. After loading the les, the size, printing position, and angle of the objects
can be adjusted accordingly.
The user may use the Convert function and change relevant settings to satisfy printing speed and effectiveness.
After editing and adjustments, select Print to export the object. The model le will be sectioned and then printed
accordingly.
Visit the XYZprinting ofcial website for more information on version updates, operating instructions, and technical
support: http://www.xyzprinting.com/ for more details and information.
Import .stl or .3w les.
Convert to .3w les.
Save .stl les.
Set printing preferences and send les for printing.
Print list
Set the language displayed for the software
interface and preview color.
Check for and update the software and rmware
versions, and open a link to the ofcial website.
Display zoom percentage
Quick switch to the preview perspective
Change model position
Change model angle
Shrink or enlarge model dimensions
Display model-related information
Delete the model from the virtual platform
Check printer temperature, lament data, and printing progress
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
L.
M.
N.
O.
A B C D E F G
H
I
J
K
L
M
N
O
Page 18
P 18
da Vinci Super 3D printer
da Vinci Super
Supporting information
If your printer experiences problems, review the following troubleshooting instructions to resolve the issue. If the issue
persists, contact the customer service center.
If your printer experiences problems, a relevant service code will be displayed on the printer screen and/or software
interface. Please refer to the following service code description table for initial troubleshooting.
Issue code and troubleshooting
Error Code No.
0 0 1 0
0 0 1 1
0 0 1 3
0 0 1 4
0 0 3 0
0 0 3 1
0 0 3 2
0 0 5 0
0 0 5 2
Failure Description
Print bed heated for too long
Print head heated for too long
Print bed heated issue--
temperature exceed
Print bed heated issue--
temperature exceed
Abnormal--X axis
Abnormal--Y axis
Abnormal--Z axis
Internal communication error -memory error
Print head memory error
User Action
Please reboot or check the print bed heater & thermistor harness connection
(need to open back cover).
Please check the Flexible at cable and reboot.
Please reboot or check the print bed heater & thermistor harness connection (need
to open back cover).
Please check the Flexible at cable and reboot.
Check the X axis cable of the motor and the sensor, and check the X axis position of
the sensor.
Check the Y axis cable of the motor and the sensor, and check the Y axis position of
the sensor.
Check the Z axis cable of the motor and the sensor, and check the Z axis position of
the sensor.
Reboot the printer.
Replace the print head.
Post-sales maintenance and services
Please retain the original packing materials. We recommend packing the printer in its original packaging before sending
the printer for repairs during the warranty period. Using other packing materials when sending the printer may result in
damages during the shipping process. XYZprinting reserves the right to charge maintenance fees when this occurs.
Loading...