Xyz printing DA Vinci Mini W+ User Manual

User Manual

English

Specification Product Overview Button and Indicator light Unpacking Accessory Checklist Important Safety Notes Extruder module installation Accessory installation XYZware operation Print Wi-Fi setup Advanced XYZware operation Function descriptions Using the accessory tools Print Bed Adjustment Error message and Action

2 2 2 3 3 3 4 4 6 6 7 10 11 14 15 16

V2 - 1 -

Product Overview

Specification

Dimensions

Weight

400 x 336 x 362 mm

8 KG

Guide tube

Feed module

Filament

Function button

/ status indicator

Extruder module

Button and Indicator light

Indicator signals Status Action

Print bed

Filament holder

Power connector

USB port

Power switch

Print Technology

Print Material

Filament Diameter

Nozzle Diameter　

Print Dimension

Print Resolution　

Connectivity

Print Software

File Format

Fuse Filament Fabrication (FFF)

PLA/ Tough PLA/ PETG

1.75 mm

0.4 mm

150 x 150 x 150 mm

0.1/0.2/0.3/0.4mm

USB 2.0/ WiFi

XYZmaker

.stl , XYZ Format (.3w), 3mf

Solid green

Flashing green

Solid red

Flashing red

Solid orange

Flashing orange

Pulsing orange

If the printer encounters issues, please refer to the XYZmaker screen troubleshooting instruction to fix the issues.

Standby/Ready to print

Receiving data

General error

Critical error

Printing

Paused

Job complete (printing complete / printing cancellation complete)

Press the button to return to printing status, refer to instructions in software to fix the issue.

Refer to instructions in the software to solve the issue or reboot the Mini.

To pause the print, press the button once. To cancel the print, press and hold the button for 5 seconds.

To resume the print, press the button once.

To return to Ready to print, press the button once.

- 2 -

Unpacking

• Before using this printer, remove all fixed materials from the extruder module and print bed. Switching on the printer without removing these fixed materials may damage the machine.

• Be sure to remove the 4 clips from the shafts as illustrated on the right.

Notes

Keep original packaging materials in case you need to send your unit back for repair during the warranty period. If other packing materials are used instead, the printer may become damaged during transportation. In such a situation, XYZprinting reserves the right to charge a repair fee.

Accessory Checklist

1. Quick Guide, Warranty Card

6. Scraper

2. Power Adapter 3. Power Cord 4. USB Wire 5. Extruder Module

7. Guide Tube 8. Bundled Filament 9. Filament Spool Ring

12. Feeding Path Cleaning Wire

Important Safety Notes

10. Bed Tape X 3pcs （Only replace

(installed on the filament spool)

13. Cleaning Wire x 511. Cleaning Brush 14. Leveling tool 15. Feeding Tube Grip X1

• Do not use the printer in dusty high humidity or outdoor environments.

• Place the printer on a stable and even surface to avoid it falling and causing serious injury.

• Do not put your hand into the machine during operation to avoid collision risk due to movement of the machine or to avoid burn due to high temperature.

the reusable tape when it is worn.）

(For replacing and installing the Feeding Tube Grip, please watch the tutorial video on XYZprinting official website)

- 3 -

Installing the Extruder module

NOTE: To unload the extruder module, first detach the heating bus and press the black disengage button.

Installing the Accessories

1. Install the guide tube

Make sure that the printer is

powered off. Place the extruder module that the fitting pin is secured the proper location.

Insert the black ribbon

connector to complete the installation.

Ensure that the guide

tube has been tightly inserted into the port.

Feed the guide tube

through the slot at the top of the printer to the extruder module.

Ensure that the guide tube

is properly inserted into the feed port of the extruder module to complete the installation.

- 4 -

2.Installing the Filament spool ring

(please refer to this step if the axle ring is not installed on the spool)

Use a phillips screwdriver to loosen the securing screws of the filament spool ring.

Separate the spool

21 3 4 5 6

ring from both sides of the spool.

Retrieve the filament spool and chip.

3.Installing the filament

Remove the side cover by pressing down

1 3

firmly at the center on the left side of the cover and pushing aside the cover. (pay attention to where you apply your force to ensure proper dismantling) Keep the side cover securely for future use.

Lower the filament spool

holder on the left side of the printer until horizontal.

Install the sensor chip. Note the orientation of the sensor chip on the spool ring.

Place the assembled filament spool (with the spool ring) on the spool holder.

Feed both parts of the spool ring through the center hole of the spool and assemble them together.

Take the tip of the

4 5

filament and insert it into the feeding hole.

Use a phillips screwdriver to tighten and secure the spool ring to complete the installation.

Press the release arm and push the filament all the way to the bottom so that the front end of the filament is completely inserted into the extruder module.

Handy tips

• The filament will load better when the tip of the filament is cut at a 45° angle.

• When the printer is not in use, raise the filament spool holder and close the side cover.

- 5 -

+ 11 hidden pages