d
a
V
i
n
c
i Mini Se
rie
s
User Manual
Specification
Product Overview
Button and Indicator light
Unpacking
Accessory Checklist
Important Safety Notes
Extruder module installation
Accessory installation
XYZware operation
Print
Wi-Fi setup (da Vinci Mini w only)
Advanced XYZware operation
Function descriptions
Using the accessory tools
Print Bed Adjustment
Error message and Action
2
2
2
3
3
3
4
4
6
6
7
10
11
14
15
16
English
V1 - 1 -
1
2
3
4
5
6
7
8
9
10
Guide tube
Feed module
Filament
Extruder module
Function button
/ status indicator
Print bed
Filament holder
Power connector
USB port
Power switch
Solid green
Flashing green
Solid red
Flashing red
Solid orange
Flashing orange
Pulsing orange
Indicator signals Status Action
Standby/Ready to print
Receiving data
General error
Critical error
Printing
Paused
-
-
Press the button to return to printing status, refer
to instructions in software to fix the issue.
To pause the print, press the button once. To
cancel the print, press and hold the button for 5
seconds.
Job complete (printing complete /
printing cancellation complete)
If the printer encounters issues, please refer to the XYZware screen troubleshooting instruction to fix
the issues.
Refer to instructions in the software to solve the
issue or reboot the Mini.
To resume the print, press the button once.
To return to Ready to print, press the
button once.
1
2
3
4
5
6
Specification
400 x 336 x 362 mm
8 KG
Fuse Filament Fabrication (FFF)
PLA
1.75 mm
0.4 mm
150 x 150 x 150 mm
0.1/0.2/0.3/0.4mm
USB 2.0 (da Vinci miniMaker)
USB 2.0/ WiFi (da Vinci Mini w)
XYZware
STL / 3W
Dimensions
Weight
Print Technology
Print Material
Filament Diameter
Nozzle Diameter
Print Dimension
Print Resolution
Connectivity
Print Software
File Format
Button and Indicator light
Product Overview
8
9
10
7
- 2 -
• Before using this printer, remove all fixed materials from the extruder module and
print bed. Switching on the printer without removing these fixed materials may
damage the machine.
• Be sure to remove the 4 clips from the shafts as illustrated on the right.
• Do not use the printer in dusty high humidity or outdoor environments.
• Place the printer on a stable and even surface to avoid it falling and causing serious injury.
• Do not put your hand into the machine during operation to avoid collision risk due to
movement of the machine or to avoid burn due to high temperature.
1. Quick Guide, Warranty Card
Keep original packaging materials in case you need to send your unit back for repair
during the warranty period.
If other packing materials are used instead, the printer may become damaged during transportation.
In such a situation, XYZprinting reserves the right to charge a repair fee.
Notes
13. Cleaning Wire x 511. Cleaning Brush
2. Power Adapter 3. Power Cord 4. USB Wire 5. Extruder Module
7. Guide Tube 8. Bundled Filament 9. Filament Spool Ring
(installed on the filament spool)
6. Scraper
14. Leveling tool
12. Feeding Path Cleaning Wire
10. Bed Tape X 3pcs （Only replace
the reusable tape when it is worn.）
16. Feeding Tube Grip X1
(For replacing and installing
the Feeding Tube Grip,
please watch the tutorial
video on XYZprinting official
website)
15. PET Protection cover
Unpacking
Accessory Checklist
Important Safety Notes
- 3 -
NOTE: To unload the extruder module, first detach the
heating bus and press the black disengage button.
Ensure that the guide tube
is properly inserted into the
feed port of the extruder
module to complete the
installation.
3
Ensure that the guide
tube has been tightly
inserted into the port.
1
Feed the guide tube
through the slot at the
top of the printer to
the extruder module.
2
Make sure that the printer is
powered off. Place the extruder
module that the fitting pin is
secured the proper location.
1
Insert the black ribbon
connector to complete
the installation.
2
Installing the
Accessories
1. Install the guide tube
Installing the
Extruder module
- 4 -
Handy tips
• The filament will load better when the tip of the filament is cut at a 45° angle.
• When the printer is not in use, raise the filament spool holder and close the side cover.
Lower the filament spool
holder on the left side of
the printer until horizontal.
Use a phillips screwdriver to loosen the
securing screws of the
filament spool ring.
(please refer to this step if the axle ring is not installed on the spool)
Install the sensor chip.
Note the orientation of
the sensor chip on the
spool ring.
Use a phillips screwdriver to tighten and
secure the spool ring
to complete the
installation.
Separate the spool ring
from both sides of the
spool.
Place the assembled
filament spool (with
the spool ring) on
the spool holder.
Press the release arm and
push the filament all the
way to the bottom so that
the front end of the
filament is completely
inserted into the extruder
module.
2
Remove the side cover by pressing down
firmly at the center on the left side of the
cover and pushing aside the cover. (pay
attention to where you apply your force to
ensure proper dismantling) Keep the side
cover securely for future use.
1 3
Take the tip of the
filament and
insert it into the
feeding hole.
4 5
3.Installing the filament
Feed both parts of the
spool ring through the
center hole of the
spool and assemble
them together.
Retrieve the filament
spool and chip.
2.Installing the Filament spool ring
21 3 4 5 6
- 5 -
Loading...