The Xyron 850 / Xyron 1200 is designed to be used with one of
the following replacement cartridges:
SL/DL: Double- and single sided lamination.
LAT: Front lamination with adhesive transfer on the reverse.
AT: Single - sided adhesive transfer.
Please follow the attached directions carefully.
Important Notice :
Your Xyron 850 / Xyron 1200 system is designed to permanently
attach a clear film or adhesive to the front and/or back of any
substrate that is run through the machine. The lamination film and
adhesive are not designed to be removed without substantial
damage to the laminated substrate. This process is NOT
recommended for any precious or single source documents.
User's Guide
Xyron Adhesive Application &
Laminating System
XYRON
®
850
XYRON
®
1200
Parts and Functions
Document Feed Tray
Used to guide document into dispenser. Leading
edge of document slides in between tray and
paddle during insertion. Align to right for A3/A4
documents, to the left for letter documents.
Document Feed
Paddle
Helps ensure
wrinkle-free output
by providing slight
back-tension on
document.
Roller
Springs
Provide spring
force on rollers.
Remove
springs to
remove rollers
and cut-blade.
Cut Blade
Slides to the left and right to cut output
material after it exits dispenser. Also
can be used to trim excess material
from leading edge of document.
Setting Up
Remove the Xyron System and Document Feed Tray from the packaging. The System is shipped with a sample
supply cartridge already installed. Install the feed tray by inserting it horizontally into the cartridge opening by the
grooves in the left and right dispenser side plates as shown below. When correctly
installed, the tray will rest horizontally.
Lower groove in
dispenser side plates
Upper groove
in dispenser
side plates
Basic operation
Step 1 - Insert and align document on feed tray.
Extend the document completely into the cartridge
opening. Align to the left for letter size documents,
to the right for A3/A4 documents.
Document
Feed Tray
Assembly
Cartridge
(reference)
Step 2 - Gently guide the document forward while
turning the handle clockwise.
Step 3 - Trim to desired length using the cut blade
at the roller exit. Apply pressure down on the
orange blade holder and slide to the left or right.
Replaceable
Supply Cartridge
Holds various lengths and
combinations of film and
adhesive depending upon
application.
Handle
Used to advance
cartridge supplies
when rotated
clockwise. Also,
feeds document
through dispenser.
Document
Output
Location where
document exits
dispenser when
handle is rotated
clockwise.
GB
Cartridge Replacement
To Install New Cartridges To Install Part-used Cartridges
Position cartridge leader
between the rubber rollers in
dispenser.
Turn handle clockwise to
advance film
Insert new supply cartridge.
Continue to turn
handle until film is
aligned and wrinklefree.
Install feed tray
and trim off
excess film
using cut blade.
Attach reusable cartridge
starter tool to partially
used supply cartridge.
Insert partially used
supply
cartridge
into
dispenser.
Note:
tool
should be
positioned
between rubber
rollers in dispenser.
Turn handle clockwise until tool has exited
dispenser and film is aligned and wrinkle-free.
Store reusable
cartridge starter
tool for later use.
Install feed tray
and trim off
excess film
using cut blade.
Remove used
supply cartridge by
pulling outward. If
there is film
between the
rollers, turn handle
counter-clockwise.
GB
Remove feed tray by
lifting upward and
gently pulling
away from
dispenser.
Laminating Cartridges (DL and SL Series)
DL201-100 Two-Sided Lamination General use - Gloss Finish
SL201-100 One-Sided Lamination General use - Gloss Finish
DL601-200 2 x Two-Sided Lamination General use 4 inch (106mm)
SL601-200 4” w - One-Sided Lamination General Use -
Gloss Finish
Adhesive Application Cartridges (AT Series)
AT201-50
Adhesive Application - Permanent High Tack
AT202-50 Adhesive Application - Permanent Low Tack
AT205-50 Adhesive Application - Permanent Acid Free
AT206-50 Adhesive Application - Non Permanent Repositionable
AT601-100 2 x Adhesive Application - Permanent High Tack
4 inch (106mm)
Combination One Side Lamination /
One Side Adhesive Application (LAT Series)
LAT201-50
1 Side Laminate / 1 Side Adhesive Application
(General Use Laminate / Permanent High Tack Adhesive)
LAT202-50 1 Side Laminate / 1 Side Adhesive Application
(General Use Laminate / Permanent Low Tack Adhesive)
LAT206-50 1 Side Laminate / 1 Side Adhesive Application
(General Use Laminate / Non-permanent Repositionable Adhesive)
Combination One Side Lamination /
One Side Magnet (LM Series)
LM201-12
1 Side Laminate / 1 Side Magnet
(General Use Laminate / Magnet Backing)
Xyron, Inc.
15820 North 84th Street
Scottsdale, AZ 85260, USA
1-800-793-3523
FAX: 480-443-0118
www.xyron.com
Xyron, Inc. USA
Xyron Europe A/S
Xyron Asia
© 2001 Xyron, Inc.
¤
¤
Laminating Cartridges (DL Series)
DL1101-100 Two-Sided Lamination
General use - Gloss Finish
SL1101-100 One-Sided Lamination
General use - Gloss Finish
Adhesive Application Cartridges (AT Series)
AT1101-50
Adhesive Application Permanent High Tack
AT1105-50 Adhesive Application -
Permanent Acid Free
AT1106-50 Adhesive Application -
Non Permanent Repositionable
Combination One Side Lamination /
One Side Adhesive Application (LAT Series)
LAT1101-50
1 Side Laminate / 1 Side Adhesive Application
(General Use Laminate / Permanent High
Tack Adhesive)
LAT1106-50
1 Side Laminate / 1 Side Adhesive Application
(General Use Laminate / Non Permanent
Repositionable Adhesive)
Combination One Side Lamination /
One Side Magnet (LM Series)
LM1101-10
1 Side Laminate / 1 Side Magnet
(General Use Laminate / Magnet Backing)
Xyron Technical Hotline
1-800-793-3523 - USA
+45-7594-5866 - Europe
®
®
Supplies available for:
XYRON
®
850 XYRON®1200
Loading...