XPiQ inc PU150-10, PU150-10B, PU150-12, PU150-12B, PU150-13 Datasheet
...
74
DESCRIPTION
The PU150 Series is comprised of single and multiple
output models for 150 watts of continuous output power.
Auto ranging input allows them to operate from any
line voltage throughout the world without a selector
strap. All models meet CISPR 22 and FCC Class B
emission limits, and comply with UL, CSA,
IEC safety and have the CE Mark to
satisfy international requirements.
NEW • AUTO-RANGING INPUT
FEATURES
• Auto-ranging universal input
• Built-in EMI filter
• Overvoltage protection
• Short-circuit protection with
auto-recovery
• Power fail detection
• 100% burn-in at full rated load
Output #1 Output #2 Output #3 Output #4
Models Vnom Imin Imax Ipeak Tol. Vnom Imin Imax Ipeak Tol. Vnom Imin Imax Tol. Vnom Imin Imax Ipeak Tol.
PU150-10 5V 0A 30A 35A 2% N/A N/A N/A
PU150-12 12V 0A 12.5A 14.5A 2% N/A N/A N/A
PU150-13 15V 0A 10A 11.6A 2% N/A N/A N/A
PU150-13-1 18V 0A 8.3A 9.7A 2% N/A N/A N/A
PU150-14 24V 0A 6.3A 7.3A 2% N/A N/A N/A
PU150-16 30V 0A 5.0A 6.0A 2% N/A N/A N/A
PU150-17 36V 0A 4.2A 4.8A 2% N/A N/A N/A
PU150-18 48V 0A 3.1A 3.6A 2% N/A N/A N/A
PU150-23 +5V 2.0A 22A 30A 2% +12V 0A 8A 10A 3% N/A N/A
PU150-24 +5V 2.0A 22A 30A 2% +15V 0A 6.4A 8A 3% N/A N/A
PU150-25 +5V 2.0A 22A 30A 2% +24V 0A 4.5A 5A 3% N/A N/A
PU150-30 +5V 2.0A 22A 30A 2% +12V 0A 8A 10A 3% –5V 0A 2.5A 3% N/A
PU150-31 +5V 2.0A 22A 30A 2% +12V 0A 8A 10A 3% –12V 0A 2.5A 3% N/A
PU150-32 +5V 2.0A 22A 30A 2% +15V 0A 6.4A 8A 3% –15V 0A 2A 3% N/A
PU150-33 +5V 2.0A 22A 30A 2% +15V 0A 6.4A 8A 3% –12V 0A 2.5A 3% N/A
PU150-40 +5V 2.0A 22A 30A 2% +12V 0A 8A 10A 3% –12V 0A 2.5A 3% F 5V 0A 5.0A 5A 3%
PU150-41 +5V 2.0A 22A 30A 2% +15V 0A 6.4A 8A 3% –15V 0A 2A 3% F24V 0A 4.5A 5A 3%
PU150-42 +5V 2.0A 22A 30A 2% +12V 0A 8A 10A 3% –12V 0A 2.5A 3% F12V 0A 4.5A 5A 3%
PU150-44 +5V 2.0A 22A 30A 2% +12V 0A 8A 10A 3% –15V 0A 2A 3% F15V 0A 4.5A 5A 3%
PU150-45 +5V 2.0A 22A 30A 2% +12V 0A 8A 10A 3% –12V 0A 2.5A 3% F24V 0A 4.5A 5A 3%
NOTE: (1) Add suffix “B” for U-bracket.
(2) Output #4 is floating. It can be connected externally for positive or negative output.
(3) All models, maximum power is derated to 110W with no forced air provided by user.
(4) All multi-output models, maximum current per output is derated to 75% with no forced air provided by user.
(5) Total output power: 110W convection, 150W with 30 cfm forced air. For covered version, 75W convection, 130W with 30cfm of forced air.
International Power Sources, Inc.
150 WATT
SWITCHING
POWER SUPPLY
OUTPUT VOLTAGE/CURRENT RATINGS CHART
75
GENERAL SPECIFICATIONS
All specifications are typical at nominal line, full load, and 25°C.
Efficiency: 70% typical on all models
Hold-up time: 15 msec minimum at 115VAC
Line regulation: ±0.5% maximum at full load
Inrush current: 20 amps @115VAC or
40 amps @230VAC at 25°C
cold start
Withstand voltage: 3000 VAC from input to output
1500 VAC from input to ground
500 VAC from output to ground
Operating temperature: 0 to +70°C*
Storage temperature: –40 to +85°C
Relative humidity: 5% to 95% non-condensing
MTBF:
100,000 hours at full load at 25°C ambient
EMI requirements:
Meets conduction limits of
CISPR 22
Class B and FCC Class B
Safety requirements: Approved to:
a) UL1950
b) CSA C22.2 No. 234
c) IEC 950 (EN60950)
Switching frequency: 100 kHz - 130 kHz
INPUT SPECIFICATIONS
Input voltage: 85 to 132 VAC, 170 to 264 VAC
Input frequency: 47 to 63 Hz
Input current: 3.4A (rms) for 115 VAC
2.0A (rms) for 230 VAC
Leakage current: 0.4mA max at 110VAC 60 hz
0.8mA max at 240VAC 50 hz
OUTPUT SPECIFICATIONS
Output voltage: See Rating Chart
Output current: See Rating Chart
Ripple and noise: 1% peak to peak maximum
Overvoltage protection: Set at 112-132% of maximum
output voltage (on output #1 only)
Overcurrent protection: All outputs protected to short
circuit conditions
Temperature coefficient: ±0.04%/°C maximum
Transient response: Maximum excursion of 4% or
better on all models, recovering to
1% of final value 500us after a
25% step load change.
*
Derate linearly from 100% load at 50°C to 50% load at 70°C
PIN CHART
NOTES:
1. Dimensions shown in inches (mm).
2. Tolerance 0.02 (0.5) maximum.
3. Input connector P1 mates with Molex housing 09-50-3051
and Moles 2878 series crimp terminal.
4. Output connector P3 mates with Molex housing 09-50-3031 or
09-50-3091 for multiple outputs and Molex 2878 series crimp terminal.
5. Connector P4 mates with Molex housing 51110-0851 and pins 50394-8100
6. Weight: 0.84 Kgs (1.86 Lbs) approx. for “B” version
P1 P2 P3 P4
PIN
1 2 3 1 2 1 2 3 1 2 3 4 5 6 7 8
Model
PU150-10 AC AC AC Return Output Return N.C. PFD Inhibit Inhibit N.C. N.C. Return -Sense +Sense Current
Neutral Line Ground +V -Ve +Ve Share
PU150-12 PU150-13
PU150-13-1 PU150-14 AC AC AC Return Output Return N.C. N.C. Inhibit Inhibit N.C. N.C. Return -Sense +Sense Current
PU150-16 PU150-17 Neutral Line Ground +V -Ve +Ve Share
PU150-18
P1 P2 P3 P4
PIN
1 2 3 1 2 1,2 3,4,5 6 7 8 9 1 2 3 4 5 6 7 8
Model
PU150-23 PU150-24
AC AC AC Comm Output Output Comm N.C. PFD N.C. N.C. Inhibit Inhibit Fan* N.C. Comm -Sense +Sense Current
PU150-25
Neutral Line Ground Return #1 #2 Return -Ve +Ve Rtn Share
PU150-30 PU150-31
AC AC AC Comm Output Output Comm Output PFD N.C. N.C. Inhibit Inhibit Fan* N.C. Comm -Sense +Sense Current
PU150-32 PU150-33
Neutral Line Ground Return #1 #2 Return #3 -Ve +Ve Rtn Share
PU150-40 PU150-41
AC AC AC Comm Output Output Comm Output PFD Output Output Inhibit Inhibit Fan* N.C. Comm -Sense +Sense Current
PU150-42 PU150-44
Neutral Line Ground Return #1 #2 Return #3 #4 #4 Rtn -Ve +Ve Rtn Share
PU150-45
MECHANICAL SPECIFICATIONS
* Fan Voltage is equal to output #2 voltage (ex. PU150-23 has +12V fan)
Your Source of Power ...
260 Hopping Brook Road, Holliston, MA 01746
TEL: (508) 429-4440 FAX: (800) 226-2100
http://www.intlpower.com
International
Power Sources, Inc.
Loading...