Phonic XP R120 Service Manual

Download

XP-R120

SIMPLE-2

YU,YL,AEZ, AK,AHA

SERVICE MANUAL

COMPACT DISC PLAYER

Apartofcontentsisadequate. Re-issuing is under request.

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual” XP-R120 (YU,YL,AEZ,AK,AHA), (S/M Code No. 09-014-445-9T1).

• This Service Manual does not include “ Test Mode “.

These item will be issued in the next supplement.

BASIC CD MECHANISM : DA23LN

S/M Code No. 09-016-445-9R1

REVISION

DATA

SPECIFICATIONS

Tracking system 3-beam laser Laser pickup Semiconductor laser D/A conversion 4-times oversampling digital

filter + 1-bit DAC

Frequency response 20 – 20,000 Hz Output PHONES/LINE OUT jack

(stereo mini-jack)

Frequency range AM: 531/530 kHz – 1,602/1,710 kHz

(9 kHz/10 kHz steps) FM: 87.5 – 108 MHz

Maximum output YU,YL,AHA: 12 mW + 12 mW

AK,AEZ: 10 mW + 10 mW (16 ohms at 1 kHz) 500 mV (47 kohms at 1 kHz)

Power supply DC 3 V using two LR6 (size AA)

alkaline batteries DC 2.4 V using two commercially available rechargeable batteries (Ni-Cd 1.2 V 700 mAh) AK,AEZ,AHA: AC house current using the supplied AC adaptor YU,YL: AC house current using an AC adaptor whose rated output is DC 5 – 6 V, 250 – 300 mA

Maximum outside dimensions

130 (W) x 30.5 (H) x 130 (D) mm (excluding projecting parts and controls) (51/8 x 11/4 x 51/8 in.)

Weight Approx. 238 g (8.3 oz.)

(excluding batteries)

AC Adaptor AC-D603HA <AHA> AC Adaptor AC-D603 <AK,AEZ> Rated input AC 230 V, 50 Hz

• Design and specifications are subject to change without

notice.

ACCESSORIES / PACKAGE LIST

REF. NO. DESCRIPTIONPART NO.

1 8B-HCB-914-010 IB,HA(3L)S<AHA> 1 8B-HCB-910-010 IB,HA(S)S<AHA> 1 8B-HCB-911-010 IB,HA(P)S<AHA> 1 8B-HCB-904-010 IB,YL(3L)S<YL> 1 8B-HCB-918-010 IB,YL(S)S<YL>

1 8B-HCB-919-010 IB,YL(P)S<YL> 1 8B-HCB-901-010 IB,U(3L)S<YU> 1 8B-HCB-908-010 IB,YU(S)S<YU> 1 8B-HCB-909-010 IB,YU(F)S<YU> 1 8B-HCB-905-010 IB,EZ(EGF)S<AK,AEZ>

1 8B-HCB-906-010 IB,EZ(SID)S<AEZ> 1 8B-HCB-907-010 IB,EZ(PHNCZ)S<AEZ> 2 87-B30-326-210 HEADPHONE,HP-M048<EXCEPT YU> 2 87-B30-224-010 HEADPHONE,HP-M033<YU>

3 87-B30-284-010 AC ADAPTOR,AC-D603KNC<AK>

3 87-B30-283-110 AC ADAPTOR,AC-D603ENC<AEZ>

3 87-B30-287-110 AC ADAPTOR,AC-D603HANC<AHA>

KANRI NO.

– 2 –

PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully the

instructions below when servicing.

WARNING!

WHEN SERVICING, DO NOT APPROACH THE LASER EXIT

WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO

CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE

FROM A DISTANCE OF MORE THAN 30cm FROM THE

SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL

PICK-UP BLOCK.

Caution: Invisible laser radiation when

open and interlocks defeated avoid expo-

sure to beam.

Advarsel:Usynling laserståling ved åbning,

når sikkerhedsafbrydere er ude af funktion.

Undgå udsættelse for stråling.

VAROITUS!

Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa mainit-

ulla tavalla saattaa altistaa käyt-täjän turvallisuusluokan 1 ylit-

tävälle näkymättömälle lasersäteilylle.

VARNING!

Om apparaten används på annat sätt än vad som specificeras i

denna bruksanvising, kan användaren utsättas för osynling

laserstrålning, som överskrider gränsen för laserklass 1.

CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous

radiation exposure.

ATTENTION

L'utilisation de commandes, réglages ou procédures autres que

ceux spécifiés peut entraîner une dangereuse exposition aux

radiations.

ADVARSEL!

Usynlig laserståling ved åbning, når sikkerhedsafbrydereer ude

af funktion. Undgå udsættelse for stråling.

This Compact Disc player is classified as a CLASS 1 LASER

product.

The CLASS 1 LASER PRODUCT label is located on the rear

exterior.

CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1

LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT

Precaution to replace Optical block (SF-P200L)

Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.

1) After the connection, remove solder shown in the right figure.

10 9

:SOLDER

116

PICK UP ASSY SF-P200

– 3 –

ELECTRICAL MAIN PARTS LIST

REF. NO.

87-A21-448-040 C-IC,BH6554FV 8B-HC1-652-030 C-IC,MN101C439-AK 87-A21-874-010 C-IC,MN35530 87-A21-733-040 C-IC,MSM51V4400D/E-70TKFS 87-A21-873-040 C-IC,AN8399SA

87-A21-449-040 C-IC,AN8746SA 87-A21-085-040 C-IC,TA2120FN 87-A20-851-040 C-IC,TA2111F 87-A21-896-040 C-IC,LC72122V 87-A20-904-080 C-IC,TK11823MTL

8B-HC1-602-010 C-IC,HD6433863A71W

TRANSISTOR

87-A30-376-040 C-TR,RN1405 87-A30-075-080 C-TR,2SA1235F 89-211-323-080 C-TR,2SB1132R 89-416-643-080 C-TR,2SD1664R 87-A30-076-080 C-TR,2SC3052F

89-113-695-680 C-TR,2SA1369G/H 87-A30-278-040 C-FET,2SK2980 87-A30-480-040 C-TR,DTC114WUA 87-A30-408-040 C-TR,DTC123JUA 87-A30-405-040 C-TR,DTC114TUA

87-A30-332-040 C-TR,CPH3106 87-026-695-040 C-TR,DTA123JUA 87-026-264-080 C-TR,RN1411 87-026-429-080 C-TR,RN2311 87-A30-377-040 C-TR,2SB815B7

87-A30-328-040 C-TR,IMX9 89-503-602-080 C-FET,2SK360E 89-327-143-080 C-TR,2SC2714O 87-A30-385-040 C-TR,DTA114YUA 89-113-625-080 C-TR,2SA1362GR

87-A30-404-040 C-TR,DTC114YUA 87-A30-143-040 C-TR,2SA1576A

DIODE

87-017-520-080 C-DIODE,SFPB52 87-A40-270-080 C-DIODE,MC2838 87-A40-880-040 C-ZENER,UDZS 10B 87-A40-590-040 C-DIODE,HRW0202A 87-020-027-080 C-DIODE,1SS184

87-020-465-080 DIODE,1SS133

MAIN C.B

C101 87-012-286-080 CAP, U 0.01-25 C102 87-A11-031-080 C-CAP,E 100-16 M WX C103 87-012-286-080 CAP, U 0.01-25 C104 87-016-367-080 C-CAP,E 47-6.3 C202 87-016-367-080 C-CAP,E 47-6.3

C203 87-012-286-080 CAP, U 0.01-25 C204 87-016-429-080 C-CAP,E 100-4 5.5N C205 87-A10-047-080 C-CAP,U 1-10 Z F C206 87-A12-159-080 C-CAP, 10-6.3 K B GRM42-6 C207 87-A10-505-040 CAP,E 220-6.3 105 SF

C208 87-016-426-080 C-CAP,E 47-4 5.5N C209 87-010-831-080 C-CAP,U,0.1-16F C210 87-A10-047-080 C-CAP,U 1-10 Z F C211 87-010-787-080 CAP, U 0.022-25 C212 87-012-267-080 C-CAP,U 270P-50 B

C213 87-A10-047-080 C-CAP,U 1-10 Z F C220 87-012-286-080 CAP, U 0.01-25 C221 87-010-805-080 CAP, S 1-16 C222 87-A10-047-080 C-CAP,U 1-10 Z F C301 87-016-350-040 CAP,E 470-4 MA GAS

PART NO. DESCRIPTIONREF. NO. KANRI

KANRI NO.

DESCRIPTION

PART NO.

NO.

C302 87-012-286-080 CAP, U 0.01-25 C303 87-012-286-080 CAP, U 0.01-25 C304 87-010-831-080 C-CAP,U,0.1-16F C305 87-012-286-080 CAP, U 0.01-25 C306 87-012-286-080 CAP, U 0.01-25

C307 87-012-286-080 CAP, U 0.01-25 C308 87-012-286-080 CAP, U 0.01-25 C309 87-016-430-080 C-CAP,E 100-6.3 5.5N C310 87-012-286-080 CAP, U 0.01-25 C313 87-012-274-080 CHIP CAP,U 1000P-50B

C314 87-012-274-080 C-CAP,U 1000P-50 K B C401 87-016-429-080 C-CAP,E 100-4 5.5N C402 87-010-831-080 C-CAP,U,0.1-16F C403 87-016-431-080 C-CAP,E 220-4 5.5N C404 87-010-831-080 C-CAP,U,0.1-16F

C405 87-010-831-080 C-CAP,U,0.1-16F C406 87-012-271-080 CAP, U 560P-50 C407 87-010-787-080 CAP, U 0.022-25 C408 87-A11-057-080 C-CAP,U 0.1-16 K B C409 87-A10-827-080 C-CAP,U 0.47-6.3 K B

C410 87-012-286-080 CAP, U 0.01-25 C411 87-010-831-080 C-CAP,U,0.1-16F C412 87-016-429-080 C-CAP,E 100-4 5.5N C413 87-010-831-080 C-CAP,U,0.1-16F C415 87-010-831-080 C-CAP,U,0.1-16F

C416 87-A10-950-080 C-CAP,S 4.7-10 Z F C417 87-012-188-080 C-CAP,U 47P-50 CH C418 87-012-184-080 C-CAP,U 33P-50 CH C419 87-012-184-080 C-CAP,U 33P-50 CH C420 87-010-831-080 C-CAP,U,0.1-16F

C421 87-010-831-080 C-CAP,U,0.1-16F C422 87-010-831-080 C-CAP,U,0.1-16F C423 87-010-831-080 C-CAP,U,0.1-16F C424 87-010-831-080 C-CAP,U,0.1-16F C426 87-012-195-080 C-CAP,U 100P-50CH

C451 87-010-831-080 C-CAP,U,0.1-16F C501 87-016-429-080 C-CAP,E 100-4 5.5N C502 87-010-831-080 C-CAP,U,0.1-16F C503 87-010-787-080 CAP, U 0.022-25 C504 87-010-787-080 CAP, U 0.022-25

C505 87-012-276-080 C-CAP,U 1500P-50 B C506 87-012-198-080 CAP 180P C507 87-012-273-080 C-CAP,U 820P-50 B C508 87-016-429-080 C-CAP,E 100-4 5.5N C509 87-012-281-080 C-CAP,U 3900P-50 B

C510 87-012-283-080 C-CAP,U 5600P-50 B C511 87-016-034-080 CHIP CAP U 0.027-25F C512 87-016-426-080 C-CAP,E 47-4 5.5N C513 87-016-034-080 CHIP CAP U 0.027-25F C514 87-A10-828-080 C-CAP,U 0.33-6.3 K B

C515 87-010-831-080 C-CAP,U,0.1-16F C516 87-012-180-080 C-CAP,U 22P-50 CH C517 87-012-180-080 C-CAP,U 22P-50 CH C520 87-016-426-080 C-CAP,E 47-4 5.5N C521 87-012-274-080 CHIP CAP,U 1000P-50B

C522 87-A10-047-080 C-CAP,U 1-10 Z F C523 87-A10-047-080 C-CAP,U 1-10 Z F C601 87-016-430-080 C-CAP,E 100-6.3 5.5N C602 87-012-286-080 CAP, U 0.01-25 C603 87-012-286-080 CAP, U 0.01-25

C701 87-016-430-080 C-CAP,E 100-6.3 5.5N C702 87-012-274-080 CHIP CAP,U 1000P-50B C703 87-012-274-080 CHIP CAP,U 1000P-50B C706 87-010-831-080 C-CAP,U,0.1-16F C707 87-A10-047-080 C-CAP,U 1-10 Z F

C708 87-A10-047-080 C-CAP,U 1-10 Z F C709 87-A10-047-080 C-CAP,U 1-10 Z F C710 87-016-421-080 C-CAP,E 10-16 5.5N C711 87-016-429-080 C-CAP,E 100-4 5.5N C712 87-A10-353-080 C-CAP,U0.22-10KB

– 4 –

PART NO.

NO.

C713 87-010-831-080 C-CAP,U,0.1-16F C714 87-A11-062-080 C-CAP,S 2.2-16 Z F C715 87-016-421-080 C-CAP,E 10-16 5.5N C716 87-010-831-080 C-CAP,U,0.1-16F C717 87-010-831-080 C-CAP,U,0.1-16F

C718 87-016-431-080 C-CAP,E 220-4 5.5N C719 87-016-431-080 C-CAP,E 220-4 5.5N C720 87-012-274-080 CHIP CAP,U 1000P-50B C721 87-012-274-080 CHIP CAP,U 1000P-50B C722 87-010-831-080 C-CAP,U,0.1-16F

CN301 87-A60-756-080 C-CONN,24P V 24FLT-SM1TB CN501 87-009-214-080 CONN,16P 52207-1690 CN601 87-099-522-080 CONN,6P ZH-SM3 V W FB701 83-XM1-617-080 C-COIL,BK2125HM601 FB702 83-XM1-617-080 C-COIL,BK2125HM601

FB703 83-XM1-617-080 C-COIL,BK2125HM601 FB704 83-XM1-617-080 C-COIL,BK2125HM601 J101 87-A61-340-010 JACK,DC J701 87-A61-339-010 JACK,3.5 GRN ST W/O SW L201 87-A50-355-080 C-COIL,330UH LQH3C

L202 87-A50-330-080 C-COIL,100UH-D75C L203 87-A50-355-080 C-COIL,330UH LQH3C L301 87-A50-367-080 C-COIL, 10UH LQG21F L302 87-A50-367-080 C-COIL, 10UH LQG21F L401 87-A50-117-080 C-COIL,10UHLQH3C

L402 87-A50-012-080 C-COIL,100UH LQH3C L501 87-A50-501-080 C-COIL,10UH-FSLB2520 L502 87-A50-367-080 C-COIL, 10UH LQG21F S101 87-A92-085-010 SW,MICRO ESE11SV1 S302 87-A91-457-280 C-SW,SL 1-1-3 SS-350-A13B-C-T

S303 87-036-379-280 C-SW,SL 1-1-2 SS-350-A12B-C-T VR701 87-A92-144-010 VR,RTRY 30KX2 H X401 87-A70-315-080 C-VIB,CER 16.93MHZ CSACWMX03-T

LID C.B

87-A91-728-110 FLTR,KIT KMFC5184-A ANT801 8B-HC1-603-010 ANT,BAR-ANTENNA BHC-1 BPF801 87-A91-681-010 FLTR,GFMB7-C1 C801 87-010-831-080 C-CAP,U,0.1-16F C802 87-012-291-080 C-CAP,U 220P-50 UJ

C803 87-012-292-080 C-CAP,U 270P-50 J UJ C804 87-012-245-080 C-CAP,U 15P-50 UJ C805 87-010-831-080 C-CAP,U,0.1-16F C806 87-012-172-080 CAPACITOR CHIP U 10P CH C807 87-012-195-080 C-CAP,U 100P-50CH

C808 87-012-286-080 CAP, U 0.01-25 C809 87-012-286-080 CAP, U 0.01-25 C810 87-012-286-080 CAP, U 0.01-25 C811 87-A10-915-080 C-CAP,U 1000P-25 J CH C812 87-012-170-080 C-CAP,U 8P-50 CH

C813 87-A10-039-080 C-CAP,U 470P-50 J CH C814 87-012-174-080 CAP CHIP CERA SS 12P CHJ C815 87-012-162-080 C-CAP,U 1P-50 CK C816 87-012-286-080 CAP, U 0.01-25 C817 87-012-286-080 CAP, U 0.01-25

C818 87-A10-260-080 C-CAP,U 0.1-16 K B C819 87-A10-420-080 C-CAP,TN 4.7-4 A TCF C820 87-012-286-080 CAP, U 0.01-25 C824 87-A12-173-080 C-CAP,U 330P-50 CH C825 87-A10-260-080 C-CAP,U 0.1-16 K B

C826 87-A10-260-080 C-CAP,U 0.1-16 K B C827 87-A11-049-080 C-CAP,U 1-6.3 K B C828 87-A10-260-080 C-CAP,U 0.1-16 K B C829 87-010-785-080 C-CAP,U0.015-25BK<YU,YL> C829 87-012-286-080 CAP, U 0.01-25<AK,AEZ,AHA>

C830 87-010-785-080 C-CAP,U0.015-25BK<YU,YL> C830 87-012-286-080 CAP, U 0.01-25<AK,AEZ,AHA> C831 87-A10-025-080 C-CAP,U 0.22-16Z F C832 87-A10-025-080 C-CAP,U 0.22-16Z F

DESCRIPTIONREF. NO. KANRI

PART NO.

NO.

C834 87-016-558-080 C-CAP,TN47-6.3F93B C835 87-012-286-080 CAP, U 0.01-25 C836 87-010-831-080 C-CAP,U,0.1-16F C837 87-012-286-080 CAP, U 0.01-25 C839 87-012-273-080 C-CAP,U 820P-50 B

C843 87-012-286-080 CAP, U 0.01-25 C845 87-012-286-080 CAP, U 0.01-25 C848 87-012-286-080 CAP, U 0.01-25 C851 87-012-176-080 CAP 15P C852 87-012-174-080 CAP CHIP CERA SS 12P CHJ

C853 87-A11-062-080 C-CAP,S 2.2-16 Z F C854 87-012-286-080 CAP, U 0.01-25 C855 87-012-286-080 CAP, U 0.01-25 C856 87-A11-063-080 C-CAP,S 4.7-10 Z F C857 87-012-195-080 C-CAP,U 100P-50CH

C858 87-012-195-080 C-CAP,U 100P-50CH C881 87-010-805-080 CAP, S 1-16 C882 87-012-286-080 CAP, U 0.01-25 C883 87-012-286-080 CAP, U 0.01-25 C884 87-010-831-080 C-CAP,U,0.1-16F

C885 87-012-170-080 C-CAP,U 8P-50 CH C886 87-012-167-080 C-CAP,U 5P-50 CH C887 87-012-337-080 C-CAP,U 56P-50 CH C891 87-012-274-080 C-CAP,U 1000P-50 KB C901 87-A10-047-080 C-CAP,U 1-10 Z F

C902 87-012-286-080 CAP, U 0.01-25 C903 87-A10-025-080 C-CAP,U 0.22-16Z F C904 87-A10-025-080 C-CAP,U 0.22-16Z F C905 87-A10-025-080 C-CAP,U 0.22-16Z F C906 87-A10-025-080 C-CAP,U 0.22-16Z F

C907 87-A10-047-080 C-CAP,U 1-10 Z F C908 87-012-198-080 CAP 180P C909 87-012-198-080 CAP 180P C910 87-A10-504-080 C-CAP,U 0.047-16 K B C911 87-010-831-080 C-CAP,U,0.1-16F

C912 87-010-831-080 C-CAP,U,0.1-16F C914 87-010-831-080 C-CAP,U,0.1-16F C915 87-010-831-080 C-CAP,U,0.1-16F CF801 87-A91-162-010 FLTR,PFS450A7 D801 87-A40-462-040 C-VARI-CAP,SVC347(S)

D802 87-A40-916-040 C-VARI-CAP,HVC202A D803 87-A40-916-040 C-VARI-CAP,HVC202A L802 87-003-247-080 C-COIL,100UH L804 8B-HC1-604-010 COIL,FM RF-EX BHC-1 L805 8B-HC1-605-010 COIL,FM OSC-EX BHC-1

L806 87-005-788-080 C-IFT,AM (450K) L881 87-A50-037-080 C-COIL,D-D 5CDLU796kHz L901 8B-HC1-607-080 C-COIL,OSC 1.00MHZ LCD901 8B-HC1-610-010 LCD, BHC-1 SW901 87-A91-668-080 C-SW,TACT EVQ-PQH-B55

SW902 87-A91-668-080 C-SW,TACT EVQ-PQH-B55 SW903 87-A91-668-080 C-SW,TACT EVQ-PQH-B55 SW904 87-A91-668-080 C-SW,TACT EVQ-PQH-B55 SW905 87-A91-668-080 C-SW,TACT EVQ-PQH-B55 SW906 87-A91-668-080 C-SW,TACT EVQ-PQH-B55

SW907 87-A91-668-080 C-SW,TACT EVQ-PQH-B55 SW908 87-A91-668-080 C-SW,TACT EVQ-PQH-B55 SW909 87-A91-668-080 C-SW,TACT EVQ-PQH-B55 SW910 87-A91-668-080 C-SW,TACT EVQ-PQH-B55 SW911 87-A91-668-080 C-SW,TACT EVQ-PQH-B55

TC801 87-011-249-080 C-TRIMER,CER 30P 4.5-3.2 ECRK X851 87-A70-082-010 VIB,XTAL 75KHZ

FLEX C.B

8B-HC1-606-010 PWB,FLEX-24P

DESCRIPTIONREF. NO. KANRI

– 5 –

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

Resistor Code

Chip resistor

Wattage Type Tolerance

1/16W 1005 5% CJ

1/16W

1/10W

1/8W

1608

2125

3216

TRANSISTOR ILLUSTRATION

CBE

Figure

Value of resistor

Symbol

Form

Dimensions (mm)

LW t

1.0 0.5 0.35 104

1.6 0.8 0.45

2 1.25 0.45

1.6

0.55

3.2

Resistor Code

: A : A

108

118

128

2SA1369G/H 2SB1132R 2SD1664R

2SK360E

2SK2980

IMX9

2SA1235F 2SA1362GR 2SA1576A 2SB815B7 2SC2714O 2SC3052F CPH3106 DTA114YUA

DTA123JUA DTC114TUA DTC114WUA DTC114YUA DTC123JUA RN1405 RN1411 RN2311

– 6 –

WIRING  1 (MAIN) <1 / 2>

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

ALKALINE BATTERIES

 7 

WIRING  1 (MAIN / FLEX : 1 / 2) <2 / 2>

1 2 3 4 5 6 7 8 9 1011121314151617181920212223242526272829303132

VIA FLEX C.B (2/2)

ON (2X)

 8 

SCHEMATIC DIAGRAM – 1 (MAIN)

– 9 –

WIRING  2 (LID) <1 / 2> (AHA)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

 10 

WIRING  2 (LID / FLEX : 2 / 2) <2 / 2> (AHA)

1 2 3 4 5 6 7 8 9 1011121314151617181920212223242526272829303132

VIA FLEX C.B (1/2)

 11 

WIRING  3 (LID) <1 / 2> (YU,YL,AK,AEZ)

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

<AK,AEZ ONLY>

<YU,YL ONLY>

 12 

WIRING  3 (LID / FLEX : 2 / 2) <2 / 2> (YU,YL,AK,AEZ)

1 2 3 4 5 6 7 8 9 1011121314151617181920212223242526272829303132

VIA FLEX C.B (1/2)

 13 

SCHEMATIC DIAGRAM – 2 (LID)

– 14 –

IC BLOCK DIAGRAM

 15 

 16 

LCD DIAGRAM

– 17 –

IC DESCRIPTION

IC, MN35530

Pin No. Pin Name I/O Description

1 DVDD3 I DRAM interface power (terminal No. 2 to 19).

2 ~ 3 D0 ~ D1 I/O DRAM data input/output signal 0 ~ 1.

4 NWE O DRAM write enable signal.

5 NRAS O DRAM RAS control signal.

6 ~ 7 D2 ~ D3 I/O DRAM data input/output signal 2 ~ 3.

8 NCAS0 O DRAM CAS control signal 0.

9 A10 O DRAM address signal 10.

10 ~ 14 A8 ~ A4 O DRAM address signal 8 ~ 4.

15 A9 O DRAM address signal 9.

16 ~ 19 A0 ~ A3 O DRAM address signal 0 ~ 3.

20 DVSS2 I Digital circuit GND.

21 DVDD2 I Digital circuit power.

22 SPOUT O Spindle motor driver signal output.

23 TRVM O Traverse drive output (+ polar output).

24 TRVP O Traverse drive output (- polar output).

25 TRM O Tracking drive output (+ polar output).

26 TRP O Tracking drive output (- polar output).

27 FOM O Focus drive output (+ polar output).

28 FOP O Focus drive output (- polar output).

29 FBAL O Focus balance adjustment output.

30 TBAL O Tracking balance adjustment output.

Specified crystal oscillation frequency signal input. (Connected to GND)

31 CSEL I “H” : Crystal oscillation fregnency = 33.8688MHz.

“L” : Crystal oscillation fregnency = 16.9344MHz.

32 FE I Focus error signal input (analogue input).

33 TE I Tracking error signal input (analogue input).

34 RFENV I RF envelope signal input (analogue input).

35 OFT I Off track signal input. “H” = Off track.

36 NRFDET I RF detection signal input. “L” = Detected.

37 BDO I Drop out signal input. “H” = Drop out.

38 LDON O Laser ON signal output. “H” = ON. (Not used)

39 ARF I RF signal input.

40 IREF I Reference current input terminal.

41 ADPVCC I AD reference voltage input (analogue input).

42 DSLF O DSL loop filter terminal.

43 DRF O Bias terminal for DSL.

44 PLLF O PLL loop filter terminal.

45 VCOF O Jitter free VCO loop filter terminal.

46 AVDD2 I Analogue circuit power (for DSL, PLL, VCOF, AD, DA).

47 AVSS2 I Analogue circuit GND (for DSL, PLL, VCOF, AD, DA).

48 OUTL O Lch audio output.

– 18 –

Pin No. Pin Name I/O Description

49 AVSS1 I Analogue circuit GND.

50 OUTR O Rch audio output.

51 AVDD1 I Analogue circuit power.

52 FSEL I Noise filter ON/OFF switch input. “L” = ON, “H” = OFF. (Connected to VDD)

53 TMOD1 I Terminal mode switch input terminal 1. Normally set to “L”. (Connected to GND)

54 TMOD2 I Terminal mode switch input terminal 2. Normally set to “L”. (Connected to GND)

55 FLAG O Flag signal output. (Not used)

Command switch: Spindle servo phase synchronizing signal output.

56 CLVS/IPFLAG O “H” = CLV, “L” = Rough servo.

Interpolation flag signal output. “H” = Interpolation. (Not used)

57 EXT0/ISRDATA I/O Command switch: Extension input/output port 0, SRDATA input. (Not used)

58 EXT1/ILRCK I/O

59 EXT2/IBCLK I/O Command switch: Extension input/output port 2, BCLK input. (Not used)

60 TX O Digital audio interface output signal. (Not used)

61 MCLK I Microcomputer command clock signal input. (Data is latched at loading edge)

62 MDATA I Microcomputer command data signal input.

63 MLD I Microcomputer command load signal input. “L” = Load.

Command switch: Extension input/output port 1, LRCK input.

“H” = Lch audio data, “L” = Rch audio data. (Not used)

64 BLKCK O Sub-code block clock signal fBLKCK = 75 Hz. (In normal PLAY mode)

65 SQCK/BCLK I/O Command switch: Sub-code Q resistor external clock input, SRDATA bit clock output. (Not used)

66 SUBQ/LRCK O

67 DMUTE/SRDATA I/O Command switch: Muting input, “H” = MUTE. Serial data output. (Connected to GND)

68 STAT O NTLOCK, BSSEL, SUBQ DATA, CDTEXT DATA, SHOCK RESISTANCE READ

69 NRST I Reset input. “L” = Reset.

70 SPPOL O Spindle motor drive signal output. (Polar output)

71 PMCK O 88.2 kHz clock signal output. (Not uesed)

72 SMCK O 4.2336 MHz clock signal output.

73 SUBC/SSYNC O Command switch: Sub-code serial output, Sector SYNC output. (Not uesed)

74 SBCK/64FS I Command switch: Clock input for sub-code serial output, 64FS output. (Not used)

75 NCLDCK O Sub-code frame clock signal output. (fCLDCK = 7.35 kHz) (Not used)

76 NTEST I Test terminal, normally set to “H”. (Connected to VDD)

77 X1 I Quartz oscillator circuit input terminal f = 16.93 MHz.

78 X2 O Quartz oscillator circuit output terminal f = 16.93 MHz.

Command switch: Sub-code Q data output, L, R discrimination signal output.

“H” = Lch audio data, “L” = Rch audio data. (Not used)

Status signal (CRC, RESY, CLVS, NTTSTOP, SQOK, FLAG6, SENSE,NFLOCK

DATA).

79 DVDD1 I Digital circuit power.

80 DVSS1 I Digital circuit GND.

– 19 –

IC, MN101C439-AK

Pin No. Pin Name I/O Description

1 ~ 7 NC - Not connected.

8 VDD - Micro-computer power voltage (2.8 V).

9 OSC2 - Not used.

10 OSC1 I Main clock oscillator (8.4 MHz).

11 VSS - Micro-computer GND.

12 XI I Sub clock input. (Connected to GND)

13 XO O Sub clock output. (Not used)

14 MMOD I Memory mode switch input. (Connected to GND)

15 VREF- - A/D converter GND.

16,17 NC - Connected to GND.

18 ACIN I AC adaptor detection terminal.

19 VDIN I Battery voltage measuring terminal.

20 NC - Connected to GND.

21 SWHO I HOLD/RESUME SW input. “L”=HOLD/RESUME ON.

22 SWEASS I EASS mode SW input terminal.

23 SWRE I RESUME SW input. “L”=RESUME ON.

24 VREF+ - AD converter supply. (Connected to VDD)

25 MDATA O DSP MDATA output.

26 STAT I DSP STAT input.

27 MCLK O DSP MCLK output.

28 TU-TXD O Tuner Micon data output.

29 TU-RXD I Tuner Micon data input.

30 TU-CLK I Tuner CLK input.

31 BEEP O Buzzer output for headphone.

32 RST I Micro-computer reset input.

33 NRST O DSP RESET output.

34 SW-IL I Pickup inner circumference limit SW.

35 PC O CD servo driver power OFF output. “L” power OFF.

36 CD-RW O Switch CD / CD RW and LD ON.

37 MLD O DSP MLD output.

38 BLKCK I DSP BLKCK input.

39 NC - Connected to GND.

40 NC - Connected to GND.

41 TU CS I Tuner CS input.

42 PU-ON O RF AMP power down output.

43 EASSON O Gain up in EASS selection output. EASS ON = “L”, OFF = “H”.

44 NC - Not connected.

45 CD-DATA-REQ O CD tuner data request output.

46 NC - Not connected.

47 NC - Not connected.

– 20 –

Pin No. Pin Name I/O Description

48 MUTE O Audio mute output.

49 NC - Not connected.

50 DSCHRG O Electric discharge output.

51 CHRG O Electric charge output.

52 NC - Not connected.

53 LCDRDO O LCD remote control output. (Not used)

54 NC - Not connected.

55 NC - Not connected.

56 SWDOOR I Door switch.

57 1/13 I Not used.

58 SPCON O Spindle motor control output. (Not used)

59 CAR-LED O Button LED light ON/OFF output. (Not used)

60 E-MODE I Shaft detect damage input. “H” = Found shaft damage. (Not used)

61 TEST I Test Mode. “L” = Test Mode.

62 M1/NM2 I EASS mode.

63 ~ 80 NC - Not connected.

– 21 –

IC, HD6433863A71W

Pin No. Pin Name I/O Description

1 BATT-LEVEL I BATT level input for battery level indication.

2 AVSS – Analog GND.

3 X1 – Connected to GND.

4 X2 – Not used.

5 VSS – GND.

6 XTAL2 O Connection terminal to oscillator terminal.

7 XTAL1 I Connection terminal to oscillator terminal.

8 TEST – Test pin. (Connected to GND)

9 RESET I Reset input.

10 DSL1 O DSL out 1 output.

11 DSL2 O DSL out 2 output.

12 BEEP O BEEP output.

13 CLK-SIFT O Clock shift output.

14 PLL-DI I PLL data input.

15 WAKE-UP I Wake up input pin for key.

16 PLL-DO O PLL data output.

17 PLL-CE O PLL chip enable output.

18 TUNER-ON O “L” output when tuner is ON.

19 PLL-CLK O PLL clock output.

20 VOL-CE O Volume IC chip enbale output. (Not used)

21 VOL-CLK O Volume IC clock output. (Not used)

22 VOL-DO O Volume IC data output. (Not used)

23 TU-ON O Tuner power supply ON/OFF output.

24 ~ 25 NC – Not connected.

26 CVCC – Power supply for CPU.

27 VSS – GND.

28 ~ 31 V3 ~ V0 – +B for LCD.

32 VCC – Power supply.

33 ~ 36 COM0 ~ COM3 O LCD common output 0 ~ 3.

37 CD-CLK O CD clock output.

38 CD-RXD I CD data input.

39 CD-TXD O CD data output.

40 CD-CE O CD IC chip enbale output.

41 CD-IN I CD-ACTIVE input.

42 CD-ON O “H” output when CD is ON.

43 MUTE O “L” output when mute.

44 P-OFF O “L” output when power OFF.

45 ~ 61 SEG0 ~ SEG16 O LCD segment 0 ~ 16 output.

62, 63 NC – Not connected.

64 SEG17 O LCD segment 17 output.

65 ~ 68 NC – Not connected.

– 22 –

Pin No. Pin Name I/O Description

69 AM STEP (10k/9k) I AM STEP (10k/9k) switch input. “H” : 10k, “L” : 9k.

70 EX / DO I EX / DO. “H” : Export, “L” : Japan.

71 BHC-1 / B I BHC-1 / B. “H” : 1, “L” : B.

72 RMC-WP I Wake up for RMC.

73 AVCC – Analog VCC.

74 KEY-FUNC0 I A / D key function 0 input.

75 KEY-FUNC1 I A / D key function 1 input.

76 KEY-FUNC2 I A / D key function 2 input.

77 RMC I Wired remote control input.

78 HOLD I “L” input when in hold mode.

79 OP / CL I Cover detection. “H” input when the cover is open.

80 AC-IN I AC adaptor input pin.

– 23 –

WAVEFORM

1IC501 PIN 9 (ARF)

2IC501 PIN 22 (FEN)

Approx 0.85 V

0.5 V/div

0.2 µs/div

3IC501 PIN 23 (FEOUT)

50 mV/div 1 ms/div

4IC301 PIN 10 (OSC1)

2 V

50 mV/div 1 ms/div

1 V/div 50 ns/div

8.46 MHz

– 24 –

ADJUSTMENT

1. Clock Adjustment Settings : • Test point : TP2 (OSC)

• Adjustment location : L901

Method : Set to AM 530kHz <YU,YL,AHA>,AM 531kHz

<AK,AEZ> and adjust L901 so that the test point becomes 1.0MHz ± 1kHz.

2. AM VT Check Settings : • Test point : TP1 (VT) Method : Set to AM 530kHz <YU,YL,AHA>,AM 531kHz

<AK,AEZ> and check that the test point is 1.0V ±

0.5V. Then set to AM 1600kHz <YU,YL,AHA>,AM 1602kHz <AK,AEZ> and check that the test point is

6.5V ± 1.0V.

3. AM Tracking Adjustment Settings : • Test point : TP8 (Lch), TP9 (Rch)

• Adjustment location :

ANT801 (Bar Antenna) ....... 600kHz <YU,YL,AHA>

ANT801 (Bar Antenna) ............... 603kHz <AK,AEZ>

TC801 ................................ 1400kHz <YU,YL,AHA>

TC801 ........................................1404kHz <AK,AEZ>

*Repeat this adjustment a few times until the wave shap has the

maximum amplitude.

4. AM IF Adjustment Settings : • Test point : TP8 (Lch), TP9 (Rch)

• Adjustment location :

L806 ................................................................ 450kHz

6. FM Tracking Adjustment Settings : • Test point : TP3 (FM-IF)

• Adjustment location : L804

Method : Set to FM 98.0MHz and adjust L804 so that the test

point is maximum and distortion is minimum.

7. FM Separation Check Settings : • Test point : PHONES (J701)

• Volume : MAX

• Input level : 60dB, 1kHz

Method : Set to FM 98.0MHz and check that the test point is

more than 17dB.

8. Mono Distortion Check Settings : • Test point : PHONES (J701)

• Volume : MAX

• Input level : 60dB, 1kHz

Method : Set to FM 98.0MHz and check that the distortion

at the test point is less than 3.0%.

5. FM VT Adjustment. Settings : • Test point : TP1 (VT)

• Adjustment location : L805

Method : Set to FM 108.0MHz and adjust L805 so that the

test point becomes 7.0V ± 0.2V. Then set to FM 87.5MHz and check that the test point is 1.5V ±

0.1V.

– 25 –

MECHANICAL EXPLODED VIEW 1 / 1

LCD

PWB

BAR ANT

DA23LN

PWB

– 26 –

MECHANICAL PARTS LIST 1 / 1

PART NO.

NO.

1 8B-HCB-007-010 WINDOW,DISPLAY (R120) 2 8B-HC1-019-010 PANEL,LID CD S 3 8B-HCB-001-010 LID,CD (R120) 4 8B-HCB-004-010 KEY,DSL (R120) 5 8B-HCB-003-010 KEY,PLAY (R120)

6 8B-HCB-006-110 KEY,BAND (R120) 7 8B-HC4-208-010 SHAFT,LID (15.8) 8 8B-HC1-207-010 PLATE,LCD 9 8A-HC1-219-010 JOINT,LCD AHC-1 10 8B-HC1-025-010 HLDR,LID CD S

11 8B-HC1-204-010 SPR-T,OPEN 335 12 8B-HCB-002-010 CABI,CENTER (R120) 13 8B-HCB-005-010 KNOB,SL OPEN (R120) 14 8B-HC1-201-010 LEVER,OPEN 15 8A-HC1-202-210 SPR-T,KNOB

16 8B-HC1-202-010 HLDR,OPEN 17 8Z-HC1-225-010 DMPR,MECHA(SP) 18 8Z-HC4-027-010 FOOT,DIA10 19 8B-HC4-202-010 BAT-CONTACT,(-) 20 8B-HC4-201-010 BAT-CONTACT,(+)

21 8B-HC1-014-010 KNOB,SL EASS 22 8B-HC1-012-010 KNOB,SL HOLD 23 8Z-HC7-216-010 BAT-CONTACT,(+)(-) (SP) 24 8B-HCB-009-010 CABI ASSY,BOTTOM (R120) A 87-067-736-010 SCREW,1.4-2 BLK NLOCK

B 87-067-384-010 SCREWVT1.4-3.5HL C 87-067-869-010 V+1.7-8 HL BLK D 83-ZM1-305-010 W,2.16-3.5-0.125

DESCRIPTIONREF. NO. KANRI

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color

B Black C Cream D Orange G Green H Gray L Blue

LT Transparent Blue N Gold P Pink

R Red S Silver ST Titan Silver

T Brown V Violet W White

WT Transparent White Y Yellow YT Transparent Yellow

LM Metallic Blue LL Light Blue GT Transparent Green LD Dark Blue DT Transparent Orange GM Metallic Green

YM Metallic Yellow DM Metallic Orange PT Transparent Pink

LA Aqua Blue GL Light Green HT Transparent Gray

– 27 –

CD MECHANISM EXPLODED VIEW 1 / 1

CD MECHANISM PARTS LIST 1 / 1

PART NO.

NO.

1 S0-A41-A20-604 PICKUP ASSY LASER P200L 2 S0-M10-A10-800 MOTOR SPINDLE ASSY 3 S0-M10-A10-900 MOTOR SLED ASSY 4 S2-311-A12-200 CHASSIS 5 S2-511-A23-200 GEAR MIDDLE

6 S2-511-A23-100 GEAR,SCREW 7 S2-511-A23-400 GEAR,RACK 8 S2-511-A07-901 SPINDLE SCREW 9 S4-S13-A00-200 SW,LEAF 10 S2-451-A18-100 HOLDER GEAR

A SS-EXE-A04-000 SCR PAN PCS 1.4-2.2 B SS-GXE-A00-301 SPECIAL SCREW M1.7-6.0 C SS-EXE-A14-100 SPECIAL SCREW D SS-GXE-A00-202 SPECIAL SCREW M1.7-4.0

DESCRIPTIONREF. NO. KANRI

– 28 –

2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111

Printed in Singapore2000058 921338

Phonic XP R120 Service Manual

Specifications and Main Features

Frequently Asked Questions

User Manual