Xindak XF-1000ES User Manual

is a registered trademark of Chengdu Xindak Electronic Co.,LTD

All rights reserved by Chengdu Xindak Electronic Co. LTD.

Chengdu Xindak Electronic Co. LTD.

No. 13, Zone A, Dongsheng Industry Park, Huaishudian Road,

Chengdu, Sichuan, China.

Tel/Fax: [phone]

www .xindak.com

XF-1000ESINSTRUCTIONS

AC LINE - Conditioner

XD3.834.048 SMS

Printed in China

Chengdu Xindak Electronic Co. LTD.

PURPOSE AND CHARACTERS

INSTRUCTIONS XF-1000ES

Thank you for purchasing this AC LINE - Conditioner specially designed for Hi-Fi acoustics.It solved
the problem of scattering sound and impure tones caused by the interface of miscellaneouswaves in
the electrical network when playing.Meanwhile,it can be used for other electrical appliances in
conformity with the conditions of this appliance,which filters the miscellaneous waves produced by
appliance itself,but does not pollute the electrical network.To better use this appliance,please read
the following content carefully.

AC POWER LINE RECEPTACLE/FILTER XF-1000ES

1

2

9

10

INDICATION

DETECT

Ground

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

Polarity

CHENGDU XINDAK ELECTRONI C CO., LTD

1

2

NO.:

Always remove mains plug f rom wall
socket befo re any ser vice unl ess
qualified to do so. This unit contains
dangerous voltages

AC INPUT

～220V/230V ±10%

50/60Hz FUSE F10A

ON

OFF

Made in China

3

5

XF-1000ES

AC 250V 10A max.

-10dB～55dB( 2～100 MHz)

Power Amplifier
3

Subtotal 5.5A M ax. (Switc hable)

6

Preamplifier/Accessories
2

Subtotal 5A Max . (Switcha ble)

3000V

470V

1000A

4

7

Digital Accessories
1

Subtotal 3A Max . (Unswitc hable)

AC POWER LINE RECEPTACLE/FILTER

SPECIFICAT ION

.......... ..... ...... ...... ..... ...... ..... ...... ...... ..... ...... ..... ...

Rating

........ .... .... ..... .... ..... .... ..... .... .... ..... .... ..... .... .... ..... ...

Max.Spike Volt

......... ..... ..... ..... ..... ..... ..... ..... ..... ..... ...

Max.Clampi ng Vol t (8x 20 SE C)

.......... ..... ...... ...... ..... ...... ..... ...... ...... .

Max.Surge C urren t (8x2 0 SEC )

8

.......... ..... ...... ...... ..... ...... ..... ...... ...... .

Noise Filte r

The switch for the power supply control: Through this switch can turn on or turn off the power of
Group 2 and Group 3 two output power socket groups.

Output Group 1: Supply output current of 3A (Max.) to the electric equipment. This socket group
CAN NOT be controlled by the power switch.On the power supply of the input socket is being
putting through, this socket group will output the power.

Output Group 2: Supply 5A(Max.) current to the electro-equipment. This socket group is controlled
by the power switch.

Output Group 3: Supply the output power of 5.5A (Max.) to the electric equipment. This socket
group is controlled by the power switch.

The grounded connection: This unit uses single-phase 3-lines input. When using the power supply
with single-phase 2-lines input which is not grounded, must ground this connection.

The power input socket: The power input interface of this machine, with the fuse box.

USING STEP

This unit requires single-phase 3-lines input. When using single-phase 2-lines power input, DO
connect the grounded biding post on back of the unit to the ground and make sure the phase of the
input power is correct.

Plug the attached 3-lines power cable into the power input socket on the rear
panel, the power indicator will be light on. Touch the phase detect touching
terminal to detect the phase of the power output socket. If the phase detect
indicator is not light, the power output socket will be: A: Ground, B: Natural,

A

C: Live. (See fig4) Otherwise, if the indicator is light it will be A: Ground,
B: Live, C: Natural.

B C

(Fig 4)

NOTICE

NAME AND FUNCTION

2

1

1

Power Indication

Power Indication

4

4

Power Switch

Power Switch

7

7

Output Group 1

Output Group 1

10

10

Grounded Connection

Grounded Connection

2

Polarity Detect Button

Polarity Detect Button

5

5

Output Group 3

Output Group 3

8

8

Power Input Socket

Power Input Socket

The phase detecting indicator：Indicate whether the phase of the power supply is corresponding.
If the indicator is on when touch the DETECT button or the indicator has been on before touching
it, it means the phase of the power supply is not corresponding, should change the phase switch to
change its phase.

The phase detect

：Put through the power. When the phase switch is in the position ,touch the
detect. If the indicator is on, it means the phase of the power supply input is not corresponding,
should change the phase switch; if the indicator is off, it means the phase of the power supply input
is corresponding.

Voltage Meter: Indicate the voltage of the power supply. The value is only for reference.

3

3

Voltage Meter

Voltage Meter

6

6

Output Group 2

Output Group 2

9

9

Polarity Switch

Polarity Switch

1

Because of the high voltage and heavy current inside, please not dismantle by yourself.

If there is
any fault, please cut off the power supply and send it to examine and repair. Please disconnect this
unit with the power supply and the connected electric equipment, before changing the fuse.

PARAMETERS

Max Spike Volt.........................................................................3000V

Max Clamping Volt (8X20s).......................................................470V

Max Surge Current (8X20s).....................................................1000A

Noise Filter..................................................-10dB~55dB(2-100MHz)

Rating...................................................................AC250V 10A Max.