Xindak CA-1, PA-1 User Manual
®
CA-1 Preamplifier
PA-1 Mono Block Power Amplifier
Important Safety InstructionsImportant Safety Instructions
CAUTION
CA-1/PA-1
!
!
E
CAUTION: Changes or modifications to this equipment not expressly
approved by the manufacturer could void the users authority to operate the
equipment .
The information contained in the manual is subject to change without notice.
Please do not tear or remove any sticker on this component by yourself
otherwise it may influence user enjoy the after-sale service.
1
C
CA-1/PA-1
Important Safety InstructionsImportant Safety Instructions
Please read all instructions and precautions carefully and completely before operating your CA-1
preamplifier and PA-1 mono block power amplifier.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Always keep this unit out of the reach of children.
8. Do not install this product near any heat sources such as radiators, heat registers, stoves, or other apparatus (
including amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
10. Unplug this apparatus during lightning storms or on the condition of long-time non-using.
11. Always disconnect your entire system from the AC mains before connecting or disconnecting any cable, or when
cleaning any component.
12.This product must be terminated with a three conductor AC mains power cord which includes an earth ground
connection, to prevent it from shock hazard, all three connections must always be used.
13. AC extension cords are not recommended to use on this product.
14. Never use flammable or combustible chemicals for cleaning audio components.
15. Never operate this product with any cover removed.
16. Never pour or spill liquids directly onto this unit.
17. Never block air flow through ventilation slots or heat sinks.
18.Keep the fuse out of short circuit.
19.Never take replacement of fuse uith non-specified values.
20.Never attempt to repair this product, if a problem occurs, contact your dealer.
21.Never expose this product to extremely high or low temperatures.
22.Never operate this product in an explosive atmosphere.
Before Use
Unpack your CA-1 or PA-1 and keep all packing materials for future transport or service, locate and remove all
accessory items from the accessory box within the shipping carton.
Accessories Included:
1. One piece of AC power cord
3. One piece of remote controller
2. One piece of user manual (This manual)
+
-
Volume
F1
S4
Bal
S1
S2
Mute
S3
REMOTE CONT ROLLE R
4. AAA batteries × 2
2
Products InformationProducts Information
Sketch Map on CA-1 Front & Rear Panel
CA-1/PA-1
HEATING
SLEEP
5 7 8
1
1
1
Warm-up Indicator
1
The indicator will be lighted when the main power gets
3 4
3 4
through, then automatically shut off after 60 seconds or
so.
2
Sleep Indicator
After the power gets through and power on by the
power switch on the rear panel, this indicator will be
light, which indicates this product enter into sleep state.
After press the sleep button to power on the system
main power, this indicator will be dead.
Sleep Button
3
Press this button, the main system power will be on;
press again, the main system power will be off and enter
to sleep state.
4
Mute Button
Press the button during work state, the preamplifier will
be in mute mode. Press it again, the product will be
IR SensoerIR Sensoer
62
1
1
0
5 7
62
1
Signal Input Terminal
RCA terminals are used for signal input.
Balance Signal Input Terminal
2
The signal is input by balance interconnect cable.
3
Balance Output Terminal
For connecting with balance input terminal of power
amplifier by balanced interconnect cable.
4
RCA Output Terminal
For connecting the RCA input terminals on power
amplifier by interconnect cable.
5
Power Button
For powering on and powering off the product.
6
Fuse Socket
Fuse socket is used for insert the fuse of the device.
7
Alternating Current Input Socket
Connect this socket with wall outlet by the attached
power cord.
released from mute.
5
Input Button
The Input channel will be selected circularly from S1-S2-
S3-Bal in order, while press the button once in work
state.
6
VOL+ Button
Press the button, increase the volume; persist on
pressing, the volume will be increased continually.
7
VOL- Button
Press the button, decrease the volume; persist on
pressing, the volume will be decreased continually.
8
Remote Signal Receiving Window
Implement the remote control function by aiming the
remote controller to this window while operation.
3
Loading...