Xerox ET 6124 X, ET 6124, ET 7424 User Manual

Operating Instructions

HOB

GBGB

English, 2

ET 6124 ET 6124 X ET 7424

Contents

Installation, 2-3

Positioning Connecting the hob Disposal

Description of the appliance, 4-5

Control panel Cooking zone description

Start-up and use, 6

Turning on the hob Turning off the hob The booster

The safety devices, 7

Pan recognition What cookware to use Acoustic signal Safety cut out Overheating protection device

Precautions and tips, 8

Practical advice on using the appliance General safety

Care and maintenance, 9

Switching the appliance off Cleaning the appliance Disassembling the hob

Installation

! Before operating your new appliance please read

this instruction booklet carefully. It contains important information concerning the safe operation, installation and maintenance of the appliance. ! Please keep these operating instructions for future reference. Pass them on to possible new owners of the appliance.

Positioning

! Keep all packaging materials out of the reach of

children. It may present a choking or suffocation hazard (see Precautions and tips). ! The appliance must be installed by a qualified professional in accordance with the instructions provided. Incorrect installation may damage property or cause harm to people or animals.

Built-in appliance

Use the appropriate cabinet to ensure that the appliance functions properly.  The supporting surface must be heat-resistant up

to a temperature of approximately 100°C.

 If the appliance is to be installed above an oven,

the oven must have a forced ventilation cooling system.

 Avoid installing the hob above a dishwasher: if

this cannot be avoided, place a waterproof separation device between the two appliances.

 Depending on the hob you want to install, the

cabinet must have the following dimensions (see figure):

590

520

 At a minimum of 40 mm from the back panel and

600 mm from any other vertical surfaces.

 So that a minimum distance of 20 mm is

maintained between the installation cavity and the cabinet underneath.

min. 20 mm

5 mm

COMPARTMENT

min. 40 mm

min. 20 mm

5 mm

FAN-ASSISTED

OVE N

min. 40 mm

Fixing

The appliance must be installed on a perfectly level supporting surface. Any deformities caused by improper fixing could change the features and the operation of the hob.

REAR SPRING ASSEMBLY

560 +/- 1

690

520

490 +/- 1

785

560 +/- 1

490 +/- 1

750 +/- 1

Ventilation

To allow adequate ventilation and to avoid overheating of the surrounding surfaces the hob should be positioned as follows:

510

490+/- 1

FRONT OF HOB

HOB FROM BELOW

KITCHEN WORKTOP

Connecting the hob

 The electrical safety of this appliance can only be

guaranteed if the latter is correctly and efficiently earthed, in compliance with regulations on electrical safety. Always ensure that this vital safety measure has been taken. If you have any doubts, call in a qualified technician to check the electrical system thoroughly.

 The manufacturer denies all responsibility for damage

resulting from a system which has not been earthed correctly.

 Before powering the appliance, check whether the

technical characteristics featured on the appliance data plate correspond with those of the mains electrical system.

 Check that the current load of the mains supply and of

the power sockets is suitable for the maximum power of the appliance, indicated on the appliance data plate. If in doubt, contact a qualified professional.

2. Loosen the cable clamp screw and remove it, using a screwdriver as a lever (see figure).

3. Remove the wire contact screws L-Nthen fasten the wires under the screw heads, respecting the colour code: Black/Blue (N), Red/Brown (L) and Bare Wire/Yellow-Green ( ).

 Position the power supply cable wires according to

the indications in the table.

 Once the connections have been made, tighten all

the terminal screws fully.

 Fasten the supply cable in place with the clamp and

close the cover of the terminal board.

Disconnect the appliance from the electricity supply before all operations.

Connect your hob to the electrical system by means of a junction box:junction box:

junction box: if the appliance is connected

junction box:junction box: permanently to the mains, an breakerbreaker

breaker, accessible if necessary, with a minimum

breakerbreaker contact opening of 3 mm should be installed.

Valid only for models with a power supply cable

Some models are supplied with a single-phase power supply cable, and should consequently only be connected to the single-phase mains. Observe the wire colours, as indicated in the diagram attached.

Electrical

connections

* Application of the simultaneity coefficient in

accordance with cei 60335-2-6 norm

Voltage, Frequency

omnipolar circuitomnipolar circuit

omnipolar circuit

omnipolar circuitomnipolar circuit

GB 220-240V

-1+N~50 Hz

Fuses,

Sections

25 A*

2,5 mm²

Valid only for models without a power supply cable

Some models are not fitted with a power supply cable, as the cable should be sized according to the type of electrical connection in use (see connection table below). To connect the cable, proceed as follows:

1. Open the terminal board by inserting a screwdriver into the side tabs of the cover. Use the screwdriver as a lever by pushing it down to open the cover (see diagram).

! If the hob is fitted above a built-in oven, the hob and the oven must be connected to the mains separately for safety reasons and to simplify operations when it is necessary to pull the oven out for some reason.

This appliance conforms to the following European Economic Community directives:

- 73/23/EEC dated 19/02/73 (Low Voltage) and subsequent amendments;

- 89/336/EEC dated 03/05/89 (Electromagnetic Compatibility) and subsequent amendments;

- 93/68/EEC dated 22/07/93 and subsequent amendments.

Disposal

 When disposing of packaging material: observe local

legislation so that the packaging may be reused.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that household appliances should not be disposed of using the normal solid urban waste cycle. Exhausted appliances should be collected separately in order to optimise the cost of re-using and recycling the materials inside the machine, while preventing potential damage to the atmosphere and to public health. The crossed-out dustbin is marked on all products to remind the owner of their obligations regarding separated waste collection. For further information relating to the correct disposal of exhausted household appliances, owners may contact the public service provided or their local dealer.

Description of the appliance

Control panel

Indicator light corresponding to the

PROGRAMMED COOKING ZONE *

PROGRAMMED COOKING

TIME indicator *

POWER (from 0 to 9) and

RESIDUAL HEAT indicators

COOKING ZONE

SELECTOR Keys

POWER (from 0 to 9) and

RESIDUAL HEAT indicators

15. 0

Booster

TIMER CONTROL key for COOKING TIME PROGRAMMING *

POWER (from 0 to 9) and RESIDUAL HEAT indicators

ZONE SELECTION indicator

COOKING ZONE SELECTOR Keys

POWER (from 0 to 9) and RESIDUAL HEAT indicators

BOOSTER * Key

POWER DECREASE Key

ON/OFF Key

POWER INCREASE Key

Controls LOCK Key

LOCK indicator light

Only available on certain models.

+ 8 hidden pages