XceedID XF2100C, XF1100C Users Manual

XceedID Corporation
3899 Hancock Expressway
Security, CO 80911
Tel: [phone]
Fax: [phone]
www.xceedid.com

Description

The Multi-technology Readers feature a rugged design and
can be installed almost anywhere. Durable, weatherproof,
UV-resistant materials, along with advanced electronics
and circuitry, protect readers against inclement weather
and exposure to sunlight.

Figure 1. Multi-technology Readers

Multi-technology Readers

Installation Guide

2. Drill two mounting holes a minimum of 3.25” (82.6 cm)
apart on the mounting surface of the door frame or wall.
Refer to Figure 3.

3. Drill one .625” (1.587 cm) diameter hole in wall for the
pigtail wire connection.

4. Follow the cable connection chart. Connect power at the
panel when installation is complete.

5. Mount the base plate to the wall using the supplied screws.

6. Install gasket if required, see Figure 2.

7. Install top cover straight on to the reader base. Do not
force the cover on. The four cover guides should ensure
the connector seats correctly.

Figure 3.

1.750
[44.5]

1.160
[29.5]

Mounting the Reader

1. Find a suitable mounting position on the door frame or wall.
Note: For out of doors or wet locations, it is recommended
that the gasket provided be installed on the base as shown
in Figure 2.

Figure 2. Gasket Installation

5.850 [148.6]

front view side view

Figure 4. Aligning base plate and top cover

8. Verify the connection is secure and install the security
screws at the top and bottom of the reader.

9. Place a screw head cover over each of the screws. The
screw head cover should be flush with the reader once in
place.

Connecting the Cable

Specifications

1. The readers are supplied with a 12-conductor cable
pigtail. Ensure the reader wiring is disconnected at the
host panel until all connections are made at the reader.
Use the cable connection chart below:

Yello w Beeper

Blue Hold

Purple Future

Green Wiegand Data 0 or RS485A

White Wiegand Data 1 or RS485A

Orange Green LED

Brown Red LED

Red Power + DC (6-16 VDC)

Black Ground

Pink Not Used

Gray Not Used

Drain Shield Ground

2. Use a DC Power source between 8-16 volts.

3. Verify the reader is properly grounded by attaching the
ground wire to an earth ground connection at the power
supply or panel end of the cable.

Testing the Reader

1. Power up the reader. A red LED will light followed by a
beeper tone, which indicates the reader is ready.

2. Present a proper card, which has been programmed to
operate the reader.
* A green LED indicates a registered badge read.
* A red LED indicates idle (ready to read) state in the
Wiegand mode.

Removing the Cover

1. Remove the plugs and security screws.

2. Slide cover off perpendicular to base.

Trouble Shooting

1. If reader does not behave normally upon installation,
verify that cover and base are connected properly:

The reader is shipped unassembled. To assemble, pull cover

away from base and rotate until the connector port on
the base is aligned with the connector port on the cover.
Snap shut.

2. Only connect wires necessary for use. Cut and/or isolate
unused wires. Connecting unnecessary wires may lead to
unexpected reader behavior.

3. If multiple reader units are installed in close proximity or
back to back, RF interference may result in reduced read
range performance.

4. A recurrent triple beep audio sequence may indicate
that the cover is not seated properly. Remove cover and
check for bent or broken pins in the connector.

Copyright © 2007-2011, XceedID. All rights reserved. Revised 2/1/2011.

Colors Black (standard), charcoal

Power supply Linear DC

Voltage range 8 - 16 VDC

Maximum and Average
Current range

XF2110C: 173 mA (max),
155mA (aver)
XF2100C: 157 mA (max),
141 mA (aver)
XF1100C: 132 mA(max),
116 mA (aver)

Temperature range -31 F to 149 F

-35 C to 65 C

Card read distance Distance can vary depending on

reader, installation conditions
and credential type.

Cable distance to panel 200 ft. max (22 gauge)

300 ft. max. (20 gauge)
500 ft. max. (18 gauge)

Wiegand output Up to 200 bits depending

on configuration and card
technology

Tamper output Open Collector

Regulatory approvals

UL, CE, and FCC (part 15)

and standards

ISO Standards ISO 14443A

ISO 15693

The voltage specification for this reader is 8-16 VDC.
Higher voltage with the specifications provides better
performance and cable run distances.

The recommended cable gauge is 18-gauge to 22-gauge.
Check with the cable supplier to determine the best choice
for the application and installation distance.

FCC compliance

The FCC requires the following statement: This reader uses
radio frequency energy and has been tested, and complies
with the limits of FCC testing. Changes, modification,
or disregard of proper installation and instructions not
expressly approved by XceedID, and is strictly prohibited by
the FCC and could void the user’s authority to operate the
equipment.

a. This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired
operation of the device.

b. Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible
d’en compromettre le fonctionnement.

Ordering Information

Product Description

XF -1100 - B
(Standard Black)

XF-2100-B
(Standard Black)

XF-2110-B
(Standard Black)

XF-1100-C (Charcoal) Mullion mount; Wiegand output

XF-2100-C (Charcoal) 1-Gang US mount;

XF-2110-C (Charcoal) 1-Gang US mount; Keypad; Wiegand

Mullion mount;
Wiegand output

1-Gang US mount;
Wiegand output

1-Gang US mount; Keypad; Wiegand
output

Wiegand output

output