Xantech s-62, s-66, s-64 Installation Instructions Manual

INSTALLATION INSTRUCTIONS

S-62, S-64, S-66

SMARTSPEAKER

TM

INTRODUCTION

The SmartSpeaker™ line consists of three physically interchangeable speaker/baffle assemblies,
installation and finishing hardware. The speaker/baffle assemblies feature a cut-out for the 480 Dinky
Link™ Infrared Receiver. The systems are designed to be mounted in a wooden-studded plasterboard or
“lath and plaster” wall. They can be mounted in most ceilings, however special acoustic treatment may be
required. The addition of the Dinky Link Infrared Receiver adds the dimension of wireless remote control
extension to any installation.

DESCRIPTION

R-61 Rough-in Kit

• The Rough-in Kit consists of a pair of molded rectangular frames, flat perforated “wings” and thread­cutting screws.

• The Rough-in Kit is mounted to the wooden studs during construction and is installed before the
plasterboard. It is not used in existing construction.

F63 Bezel/Grille

• The molded plastic bezel mounts directly to the wall or ceiling, with or without the Rough-in Kit. It is held
in place by four “dogs” which slip through the rectangular wall cutout and rotate into clamping position
as they are tightened.

• The bezel can be painted to match the mounting surface after it is installed.

• The perforated metal grille should be painted, if desired, before installation.

• The grille should be carefully installed after the speaker/baffle assembly has been mounted. Care should
be taken so that the edges of the grille do not scratch the finished surfaces of the bezel. The grille should
be painted, if desired, before installation.

Speakers & Volume Controls



1

S-62, S-64 and S-66 Speaker Systems

• Each system, consisting of a woofer, a tweeter and
a matching crossover network, is mounted on a
baffle panel.

• The baffle panels for all three systems are sized to
mount in the F-63 Bezel. Since the sizes are iden­tical and the system is installed only after the con­struction and painting is finished, the choice of
which system to use can be left until the end of the
job.

• The speaker/baffle assembly fastens to the bezel
with four thread-cutting screws (supplied).

Dinky Link

The 480 Dinky Link Infrared Receiver is a miniature

•

IR receiver. The 480 makes it possible to extend the
functional range of infrared remote controllers to
rooms other than those which house the controlled
equipment.

• Xantech manufactures a complete line of Infrared
Receivers, Keypads, Emitters, Audio Video &
Speaker Switchers, Zone Controllers and a Multi­Channel Audio Amplifier.

Fig. 1a

Fig. 1b

INSTALLATION

New Construction

• After framing but before plasterboard is applied,
assemble the Rough-in Kit.

• Figure 1a illustrates the usual arrangement for
mounting the speaker system vertically between
studs located on 16-inch centers. Figures 1b and 1c
show alternate arrangements for horizontal and
ceiling mounting.

• Fasten the Rough-in Kit to the studs with four
drywall screws (supplied). The frame should project
out of the wall so that it will line the hole to be cut in
the drywall.

• Figure 2a illustrates a correctly mounted Rough-in
Kit mounted between studs on 16-inch centers.

• Figures 2b and 2c show alternate arrangements
while Figure 2d shows a typical ceiling installation.

• Figure 3 illustrates an exploded, cutaway view of a
typical installation. (a) is the stud-mounted Rough­in Kit, (b) is the plasterboard with the mounting hole
cut, (c) is the bezel with the four mounting “dogs”, (d)
is the baffle panel and speaker components and (e)
is the optional Dinky Link Infrared Receiver.

• Figure 4 shows the action of the rotating mounting
“dogs”.

Fig. 1c

Amplifier

Preampli

2



f

SPEAKERS