X10 VK75A User Manual

OWNER'S MANUAL

XM14A

OWER SUPPLY

CAMERA

POSITION

SweepCenter

SCAN

GIK

Program

Normal

XC18A CAMERA

CR14A R

EMOTE

ZC15A

AN 'N

P TILT BASE

MODEL VK75A PAN 'N TILT CAMERA SYSTEM

INCLUDES ZC15A PAN 'N TILT BASE, XM14A ADDRESSABLE

SUPPLY, CR14A REMOTE, AND XC18A CAMERA

POWER

INTRODUCTION

CONTENTS

The VK75A includes the ZC15A Pan ‘n Tilt Camera Base with XM14A remote controlled power supply, the XC18A Wireless Camera, and the CR14A remote control. The wireless camera is attached to the Pan ‘n Tilt Camera Base. The camera sends the picture and sound to a receiver that you connect to your TV, up to 100 ft. away. (Receiver sold separately). You can remotely control the camera’s position (pan and tilt it) using a CR14A remote control.

FCC CAUTION

THIS DEVICE COMPLIES WITH PAR T 15 OF THE FCC RULES. OPERA TION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1)THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2)THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING

INTERFERENCE THA T MA Y CAUSE UNDESIRED OPERA TION.

This equipment generates and uses radio frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturers instructions, it may cause interference to radio and television reception. It has been type tested and found to comply with the limits for remote control devices in accordance with the specifications in Sub-Parts B and C of Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by unplugging the equipment, try to correct the interference by one or more of the following measures.

• Reorient the antenna of the radio/TV experiencing the interference.

• Relocate the equipment with respect to the radio/TV.

• Move the equipment away from the radio/TV .

• Plug the equipment into an outlet on a different electrical circuit from the radio/TV experiencing the interference.

• If necessary, consult your local Dealer for additional suggestions.

NOTE: Modifications to this product will void the user's authority to operate this equipment.

CONTROLS AND CONNECTIONS ...............................................................4

AN 'N TILT BASE WITH CAMERA AND POWER SUPPLY ............................4

ECEIVER .........................................................................................5

ONNECTING UP .................................................................................. 6

ONNECTING UP THE PAN 'N TILT BASE AND CAMERA ............................6

ONNECTING UP THE RECEIVER ...........................................................9

EMOTE CONTROL ..............................................................................10

NSTALLING THE BATTERIES................................................................10

INGLE CAMERA OPERATION................................................................ 11

TORING SWEEP POSITIONS .............................................................. 11

LEARING ALL STORED POSITIONS .................................................... 11

ENTERING ....................................................................................11

WEEPING ......................................................................................11

TOPPING A SWEEP .......................................................................... 11

URNING THE CAMERA OFF ............................................................. 11

ULTI-CAMERA SYSTEMS ....................................................................12

NSTALLING A TRANSCEIVER ............................................................... 12

URNING CAMERAS ON AND OFF ........................................................ 12

TORING SWEEP POSITIONS .............................................................. 13

LEARING ALL STORED POSITIONS ....................................................13

ENTERING ....................................................................................13

WEEPING ......................................................................................14

TOPPING A SWEEP ..........................................................................14

O CHANGE THE CODES THAT C1 THRU C4 CONTROL ........................... 14

ROUBLESHOOTING .............................................................................15

ARRANTY ......................................................................................... 19

CONTROLS AND CONNECTIONS

Point the raised dimple on the antenna towards the Receiver’s location.

XC18A camera.

ZC15A Pan 'n

Tilt Base.

Plug power supply in here.

Set channel switch (under rubber plug) to match setting on VR31A or VR36A Receiver. (A is at bottom, D is at top). It is factory set to A.

Remove clear cap and

turn lens counterclockwise

to focus (replace cap for

outdoor use).

Attach to a wall using mounting bracket (supplied).

Outdoors

Indoors

VR36A VIDEO RECEIVER (SOLD SEPARATE LY)

2.4 GHz Video Antenna

Power Supply

Jack

Video Out Jack

2.4 GHz

Channel Switch

Set the code used to turn on and off from X10 remote controls.

ON-OFF Switch

XM14A

CONNECTING UP

ATTACH THE CAMERA TO THE PAN 'N TILT BASE, THEN ATT ACH

BASE TO THE MOUNTING BRACKET, THEN ATT ACH THE

THE

BRACKET TO A WALL.

The camera included with the VK75A is already attached to the Pan 'n Tilt Base for your convenience. If however you want to remove the camera for any reason, please see the following instructions to reattach it.

1. Remove the top from the Pan ‘n Tilt base, position the camera with its cable at the front of the top housing (where the notch for the cable is) and attach the camera to the housing using the screws provided.

2. Remove the spindle attached on the inside of the top housing, neatly coil the camera wire into the spindle.

3. Put the coiled spindle back into the top housing and use the supplied washer head screw to attach it in the housing.

4. Plug the power jack from camera into the jack on the Pan ‘n Tilt base, and put the jacks into the top housing. (Only Instant-On cameras fit).

5. Attach the top housing to the Pan ‘n Tilt base, make sure the front of the housing goes to the front of the Pan ‘n Tilt base.

XC18A camera

6. Attach the Pan 'n Tilt base to the mounting bracket.

7. Install the complete assembly in a suitable location. If you install it outdoors, run the jack through a hole in the wall, or through a window, so you can plug the power supply into an AC outlet indoors.

Indoors

Outdoors

Pan 'n Tilt Base

Mounting Bracket

FRONT

ZC15A

Pan 'n Tilt Base

8. Plug the power supply’s jack into the cable on the Pan 'n Tilt Base.

9. Plug the power supply into any 120V AC outlet.

10.Set the Housecode dial to a letter between A and P that matches the Housecode dial on the X10 remote controls you want to use it with. Set the Unit Code dial to a number between 1 and 4. This lets you turn the camera connected to the XM14A on and off by remote control, using the CR14A remote (Transceiver required).

XM14A

+ 7 hidden pages