X-10 REX-10 User Manual

REX-10 BARKING DOG

REX-10

BARKING DOG ALARM

USER MANUAL

BETRIEBSANLEITUNG

GUIDE UTILISATEUR

GEBRUIKERSHANDLEIDING

ADDENDUM (for all languages!)

REX-10 BARKING DOG

CE Declaration of Conformity

UK

We, X10 Europe, 3 Rue de Penthièvre - 75008 Paris - France, herewith declare that the following
designated product: REX-10, is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC.

DE

Wir, X10 Europe, 3 Rue de Penthièvre - 75008 Paris – France, erklären hiermit die Übereinstimmung
des Gerätes REX-10 mit den grundlegenden Anforderungen und anderen relevanten Festlegungen
der Richtlinie 1999/5/EC.

FR

Nous, X10 Europe, 3 Rue de Penthièvre - 75008 Paris - France, déclarons que le produit suivant:
REX-10 les exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.

NL

Hierbij verklaart X10 Europe, 3 Rue de Penthièvre - 75008 Paris - France dat het toestel REX -10 in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn

1999/5/EG

S

Por medio de la presente X10 Europe, 3 Rue de Penthièvre - 75008 Paris - France, declara que el
REX-10 cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles

de la Directiva 1999/5/CE.

IT

Con la presente X10 Europe, 3 Rue de Penthièvre - 75008 Paris - France, dichiara che questo REX ­10 è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva
1999/5/CE.

SE

Härmed intygar X10 Europe, 3 Rue de Penthièvre - 75008 Paris - France - att denna REX -10 står I
överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som
framgår av direktiv 1999/5/EG.

SAFETY WARNINGS

• To prevent short circuits, this product (except the outdoor specified products) should only be used ins ide and
only in dry spaces. Do not expose the components to rain or humidity. Do not use the product close to a bath,

swimming pool etc.

• Only connect the adapter to the mains after checking whether the mains voltage is the same as the values on
the rating labels. Never connect an adapter or power cord when it is damaged. In that case, contact your

supplier.

• Do not expose the components of your systems to extremely high temperatures, high humidity, strong
mechanical tear, wear and strong vibrations.

• The appliance must not be changed or dismantled. The entire product may not be modified. It is prohibited to
open the housing, the device contains live parts. Defected pieces must be replaced by original parts. Any

operation on the appliances must be done by qualified technicians. In case of damages due to a non-respect of
the user guide, the guarantee does not apply.

• Adapters: Only connect the adapters to the mains after you have checked whether the mains voltage
corresponds with the value on the type tags. Never connect an adapter or cable when it is damaged. In that

case, contact your supplier.

• Batteries: keep batteries out of the reach of children. Dispose of batteries as chemical waste. Never use old
and new batteries or different types of batteries together. Remove the batteries when you are not using the

system for a longer period of time. Check the polarity (+/-) of the batteries when inserting them in the product.
Wrong positioning can cause an explosion.

• In case of improper usage or if you have opened, altered and repaired the product yourself, all guarantees
expire. The manufacturer does not accept responsibility in the case of improper usage of the product or when
the product is used for purposes other than specified.

• The manufacturer does not accept res ponsibility for additional damage other than covered by the legal product
responsibility.

REX-10 BARKING DOG

REX-10 Base Console DK10:

1. Loudspeaker

2. Power Supply

3. Battery compartment (9x”C”)

4. Loudspeaker Volume

5. House Code Dial switch

6. Install. Slide switch

7. Status LED

8. Mode Switch (Arm / Dis-arm)

REX-10 Outdoor Motion Sensor DM10:

1. PIR Motion Sensor

2. Dusk/Dawn Sensor

3. Battery compartment (4x“AA”)

4. House- Unit Code Dial switch

5. Test button

6. Status LED

7. Mounting clips

REX-10 BARKING DOG

USER MANUAL

Set-Up and Operating Instructions for REX -10™ Barking Dog Alarm (DK10),
Outdoor Motion Sensor (DM10E) and (optional) Key Chain Remote (KR22).

Simple Set-up

Follow these steps to quickly get your Barking Dog system working.
Remove the battery cover on the back of Barking Dog and install 9 “C” cell
alkaline batteries (observe polarity). Replace the battery cover and plug the AC

power cord into any convenient AC outlet near a window or outside door where it
will easily be heard by someone approaching your home.
Note: batteries are for back up only, in case the AC power fails.

To test the system

Make sure the slide switch on the back of Barking Dog is set
to RUN (to the left). Press the “A1-ON” button on the key

chain remote or any other X10 controller. Barking Dog starts
barking. Adjust the volume control on the back to a level that

can be heard from outside your home. If you installed any
(optional) X10 Light Control Modules, five seconds after
barking starts Barking Dog will turn on any X10 Modules

which are set to A1. The barking will stop approximately 30
seconds later, or press the “A1-OFF” button on the remote
to tell Barking Dog to stop barking.

If you installed any optional X10 light
control modules, you can turn on any

module set to A2 fr om the 2-ON button on
the key chain remote or other X10
controller. (Modules set to A1 will turn on

when Barking Dog starts barking). To learn
more about installing additional
accessories or changing any of the default

settings, read on:

Optional Remote Controls

You can use several types of X10 (remote)
controls to activate Barking Dog. These

controllers fall into different categories:
Home Automation (HA) wireless remotes,

HA plug-in controllers, and security
wireless remotes.

HA wireless remotes such as the KR22 or the optional SH624, or any X10 RF
Wall Switch like SS13 do not need to be installed. The default setting for Barking

Dog is A1 so you activate Barking Dog from these remotes by pressing the 1-ON
button. Pressing the 1-OFF button while Barking Dog is barking tells it to stop.

REX-10 BARKING DOG

HA plug-in controllers: ANY X10 controller such as the MT10 Mini Timer,
SC9000 Console, CM11 Computer Interface, CM15Pro Computer interface, etc.
can control Barking Dog. The default House Code and Unit Code for the DK10 is

A1 so A1-ON tells Barking Dog to bark, and A1-OFF tells it to stop barking.
To change Barking Dog's default setting of A1 so you can activate Barking

Dog with a different code: Move the slide switch on the back of Barking Dog to
INSTALL. Make sur e the House Code dial on the Remote Control matches the
letter you set on the back of Barking Dog. Press any button on the Remote

Control. Set the slide switch back to RUN. For example if you pressed button
number 5 on the Remote Control, Barking Dog will now be activated by 5-ON and
silenced by 5-OFF, and it will turn on X10 modules set to number 5, five seconds

after it is tripped.

Motion Detector Model DM10E

The included outdoor battery operated Motion Detector will
tell Barking Dog to start barking whenever someone
approaches your home. This motion detector can also turn

lights on at dusk and turn them off again at dawn.

To set up the DM10E Motion Detector

Remove the screw from the front cover on the Motion Detector and remove the
cover. Unclip the Motion Detector from the back plate. Remove the 2 screws from
the battery compartment cover. Insert 4 “AA” alkaline batteries (observe polarity).

Replace the battery cover. Attach the back plate to an exterior wall in a location
where the Motion Detector will see any intruder who approaches your home. Clip
the Motion Detector onto the back plate. Refit the cover. Adjust the swivel up and

down for best coverage. Wait for approximately 60 seconds after installing the
batteries to let the sensing circuitry settle before testing the unit.

To test the DM10 Motion Detector

Make sure the slide switch on the back of Barking Dog is set to RUN (to the left).
Arm Barking Dog, by pressing the button on the back. The small red light on the

back turns on. Walk past the Motion Detector. Barking Dog starts barking. Five
seconds after barking starts Barking Dog will turn on Lamp Modules (which are
set to A1). The barking will stop approximately 4 minutes later. If the Motion

Detector is tripped again the sequence repeats itself, if no motion is detected for 4
minutes, Barking Dog goes quiet, and the Lamp Module set to A1 will turn off.
Note: after the Motion Detector has been tripped it will not trip again for a period

of 30 seconds (for longer battery life). Press the button on the back of Barking
Dog to disarm it, the red light goes off.

REX-10 BARKING DOG

Note: the key chain remote normally controls X10 codes A1 to A4.
To change the key chain’s House Code

• Press and hold the first (top) ON button. The red LED blinks once. 3 seconds
later, the LED blinks the current setting: 1 blink for House Code A, 2 blinks for

B..... 16 blinks for P.

• Release the first (top) ON button.

• Press and release the first (top) ON button the appropriate number of times

for the House Code you want to set. Once for A, twice for B, etc. The LED
blinks for each press.

IMPORTANT: Hold the button on your last press. 3 seconds later, the red LED
blinks back the new setting, e.g. 3 blinks for House Code C. If you do not follow

this programming sequence, the LED will stay on for 1 second and your existing
setting will not be changed.

To change the Unit Code for the key chain's remote (the second pair of
buttons are always one # higher than the first pair, i.e. if you set the first button to
6, the second button controls 7, etc.).

• Press and hold the top OFF button. The red LED blinks once. 3 seconds later,
the LED blinks the current setting: 1 blink for Unit Code 1, 2 blinks for 2, 16
blinks for 16.

• Release the top OFF button.

• Press and release the top OFF button the appropriate number of times for the

Unit Code you want.

IMPORTANT: Hold the button on your last press. 3 seconds later new code blinks
back. If you do not follow this programming sequence, the LED will stay on for
1second and your existing setting will not be changed.

To change the battery: Pry the unit apart and fit a CR2025 Lithium 3V battery.
Observe polarity. You will also need to change the code that Barking Dog

responds to; see To change Barking Dog's default setting of A1.
NOTE: NO CHANGES OR MODIFICA TIONS MAY BE MADE TO THE UNITS.

ANY CHANGES MADE TO THE UNITS WILL VOID THE USER'S AUTHORITY
TO OPERATE THE EQUIPMENT.