Wyse Technology VX0LE User Manual

Download

Inst allation Guide

Wyse® VX0LE Conversion to ThinOS

Wyse® Simple ImagerTM Release 2.0.2 Wyse Device Manager

Issue: 070111 PN: 883887-05L Rev. B

Release 4.8.5

Copyright Notices

transcribe, store in a retrieval system, or translate into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, any part of this publication without express written permission.

End User License Agreement (“License”)

A copy of the Wyse Technology End User License Agreement is included in the software and provided for your reference only. The License at http://www.wyse.com/license agreement. By copying, using, or installing the software or the product, you agree to be bound by those terms.

Trademarks

The Wyse logo and Wyse are trademarks of Wyse Technology Inc. Other product names mentioned herein are for identification purposes only and may be trademarks and/or registered trademarks of their respective companies. Specifications subject to change without notice.

Restricted Rights Legend

You acknowledge that the Software is of U.S. origin. You agree to comply with all applicable international and national laws that apply to the Software, including the U.S. Export Administration Regulations, as well as end-user, end-use and country destination restrictions issued by U.S. and other governments. For additional information on exporting the Software, see http://www.microsoft.com/exporting

as of the purchase date is the controlling licensing

Ordering Information

For availability, pricing, and ordering information in the United States and Canada, call 1-800-GET-WYSE (1-800-438-9973) or visit us at http://www.wyse.com

. In all other countries, contact your sales representative.

Content s

1 Introduction 1

Kit Contents 1 Wyse Technical Support 2

Related Documentation and Services 2 Wyse Online Community 2

2 Converting Wyse VX0LE to

ThinOS 3

Procedures: Using Wyse Simple Imager 3 Procedures: Using Wyse Device Manager 7

A Installing Wyse Simple Imager 2.0.2 9

Pre-Installation Checklist 9 Procedures 10

B Troubleshooting 13

iv Contents

This page intentionally blank.

1 Introduction

Kit Contents

This guide provides the instructions you need to use Wyse® Simple ImagerTM or Wyse Device Manager

• V30LE (part numbers include: 902134, 902142, 902179, and 902180)

• V50LE (part numbers include: 902135, 902143, 902181, and 902182)

• V90LE (part numbers include: 902136, 902144, 902183, and 902184)

• V90LEW (part number: 902188)

The conversion kit includes:

• 1 Year ThinOS Maintenance (you will receive an email from Wyse or your reseller with full instructions)

• Conversion Software Assembly DVD-ROM

• Wyse Conversion Labels (you must attach a Wyse label to each converted cloud client)

Figure 1 Kit contents

to convert the following Wyse VX0LE cloud clients to ThinOS:

The Conversion Software Assembly DVD-ROM contains:

• A PDF of this Reference Guide

• Wyse Simple Imager Release 2.0.2

• VX0LE 128MB ThinOS Conversion Images folder containing the following:

· WSI VX0LE 128MB ThinOS Conversion folder containing:

1V12 folder 1V12.i2d file

· WDM VX0LE 128MB ThinOS Conversion folder containing:

ConvertVX0toV10 folder ConvertVX0toV10.rsp file

2 Chapter 1

Wyse Technical Support

To access Wyse technical resources, visit http://www.wyse.com/support. If you still have questions, you can submit your questions using the Wyse Self-Service Center at

http://support.wyse.com/selfservice.html

(toll free in U.S. and Canada). Hours of operation are from 6:00 A.M. to 5:00 P.M. Pacific Time, Monday through Friday.

or call Customer Support at 1-800-800-WYSE

To access international support, visit http://www.wyse.com/global

Wyse Online Community

Wyse maintains an online community where users of our products can see k and exchange information on user forums. Visit the Wyse Online Community forums at:

http://community.wyse.com/forum

, click the link for your hardware

2 Converting Wyse VX0LE to

Caution

ThinOS

This chapter provides the step-by-step instructions you need to convert supported Wyse VX0LE cloud clients to ThinOS.

Depending on the Wyse product you want to use, complete one of the following:

• "Procedures: Using Wyse Simple Imager"

• "Procedures: Using Wyse Device Manager"

Procedures: Using Wyse Simple Imager

Step 1: Install Wyse Simple Imager 2.0.2

Install Wyse Simple Imager 2.0.2 (contained on the Conversion Software Assembly DVD-ROM) using the instructions in "Installing Wyse Simple Imager 2.0.2."

Step 2: Copy the 1V12 Folder and 1V12.i2d File (on the DVD-ROM) to Correct Locations

1. Open the VX0LE 128MB ThinOS Conversion Images folder on the Conversion Software Assembly DVD-ROM.

2. Open the WSI VX0LE 128MB ThinOS Conversion folder (contained in the VX0LE 128MB ThinOS Conversion Images folder).

3. Copy the 1V12 folder (contained in the WSI VX0LE 128MB ThinOS Conversion folder) to C:\Inetpub\ftproot\Rapport\Tools\sa (this is a folder created by WSI during installation when using the default installation settings; see "Step 3: Install Wyse Simple Imager"). Note that this 1V12 folder will overwrite the existing 1V12 folder created during the installation.

4. Copy the 1V12.i2d file (contained in the WSI VX0LE 128MB ThinOS Conversion folder) to any folder on the machine to which you installed WSI (be sure the folder is accessible by WSI).

Step 3: Use Wyse Simple Imager to Convert Each Cloud Client

Use the following guidelines on each cloud client you want to convert:

1. Connect the cloud client (to be imaged) to the router with DHCP running that is attached to the machine on which Wyse Simple Imager is installed. Be sure the cloud client is shut down.

Ensure all software firewalls and antivirus services are stopped.

2. Launch the Wyse Simple Imager console (double-click the W yse Simple Imager icon).

4 Chapter 2

Tip

Figure 2 Wyse Simple Imager console

3. Select V12 in the Select Product list, and then click Add to open the Add Image dialog

box.

Figure 3 Add Image dialog box

4. Use the following guidelines:

• Product - V12 is automatically entered (leave this value).

• Image Version - Enter Conversion for Image Version. This refers to the new

Firmware version.

• Flash Size - This is the amount of flash memory installed in your cloud client. Flash

Size can be 128, 256, 512, 1024, 2048. NOTE: To determine the flash size of your cloud client (location of the flash size is as follows):

·V30LE: Start > Control Panel > System > System Info tab

·V50LE: Start > Control Panel > System > System Information > Identity tab

·V90LE and V90LEW: Start > Control Panel > System > Client Information >

General tab

See your cloud client documentation for help on viewing the flash size.

• Description - Enter what you want for your information. This information will help

you identify the characteristics of the device for which you are using this image. IMPORTANT: Be sure to use only Alphanumeric characters (A through Z and 0 through 9), underscore (_), or spaces.

• Image File - Click Browse, navigate to the folder on your hard drive that contains

the 1V12.i2d file (this is the location you selected in "Step 2: Copy the 1V12 Folder and 1V12.i2d File (on the DVD-ROM) to Correct Locations"), click on the 1V12.i2d

Converting Wyse VX0LE to ThinOS 5

Caution

file to select it (you may need to select the All Files option fr om the Files of Type box to display the 1V12.i2d file for selection), and then click Open.

Do not use the 1V12.i2d file directly from the Conversion Software Assembly DVD-ROM.

Figure 4 Browse to select 1V12.i2d file

5. After you have completed configuring the Add Image dialog box, click OK. After the

image file has been successfully added, the success message appears.

Figure 5 Image successfully added

6. Click OK. The firmware image now app ears in the Wyse Simple Imager conso le and is

ready to be submitted.

7. Select the firmware you added in the Select Firmware list and click Submit. After the image file has been successfully submitted, the Please start/restart the client to start

imaging message appears.

Do not close the console until after the cloud client is successfully imaged

with the new firmware.

Figure 6 Start/Restart the client to start imaging

8. Click OK.

9. After the Log window appears, start the cloud client. After the imaging process is

complete, the Log window will display the log messages and the final status. If the imaging was successful, a Success message will be displayed. If it failed, it will display an error message (see "Troubleshooting").

6 Chapter 2

Caution

Tip

Warning

Step 4: Attach a Wyse Conversion Label on Each Converted Cloud Client

The conversion kit is supplied with Wyse Conversion Labels that must be attached to each cloud client as shown in Figure 7. Be sure you have purchased the amount of labels you need.

Failure to install the label may cause delays in service and support. The serial number must be given to a Customer Support Technician to validate entitlement to support and service from Wyse. Failure to do so will result in the original operating system being loaded on the device and is in breach of your license agreement.

Figure 7 Placement of Wyse Conversion Label

Step 5: Obtain a Firmware Update

After converting your cloud clients, you must use your 1 Year ThinOS Maintenance (you should have received an email from Wyse or your reseller with full instructions) to obtain any available firmware update (if you did not receive this email, contact your reseller).

If you are unfamiliar with updating firmware on your Wyse ThinOS cloud client, refer to Wyse Knowledge Base Solution #10566 (go to the Wyse Knowledge Base at http://www.wyse.com/kb

Wyse Cloud Client Software Maintenance is required to be eligible to receive new versions of cloud client software and subsequent releases of corresponding documentation and tools. Wyse announces new versions of software through the WyseView newsletter. To receive notification of available software updates, customers must subscribe to the fre e WyseView newsletter at http://www.wyse.com/wyseview than one device requires that you first purchase from Wyse additiona l copies of, or licenses to, the Software. Contact your local Wyse distributor or Wyse Inside Sales at 1-800-800-9973 option 1 or 1-408-473-1200 option 1.

and search for 10566).

. Use of the Software on more

Converting Wyse VX0LE to ThinOS 7

Caution

Tip

Procedures: Using Wyse Device Manager

Step 1: Access the DVD-ROM from the Correct WDM Server

Access the Conversion Software Assembly DVD-ROM from the machine to which you installed the WDM Administrator Console (MMC Snap -i n ).

Step 2: Copy the WDM VX0LE 128MB ThinOS Conversion Folder (on the DVD-ROM) to

C:\WDM_Packages

1. Open the VX0LE 128MB ThinOS Conversion Images folder on the Conversion Software Assembly DVD-ROM.

2. Copy the WDM VX0LE 128MB ThinOS Conversion folder (contained in the VX0LE 128MB ThinOS Conversion Images folder) to C:\WDM_Packages.

Step 3: Register and Deploy the WDM Package

Use WDM to register and deploy the WDM package as you normally would. For more information on registering a package from a script file (.rs p) , see Administrators Guide:

Wyse Device Manager

Step 4: Attach a Wyse Conversion Label on Each Converted Cloud Client

The conversion kit is supplied with Wyse Conversion Labels that must be attached to each cloud client as shown in Figure 8. Be sure you have purchased the amount of labels you need.

Figure 8 Placement of Wyse Conversion Label

Step 5: Obtain a Firmware Update

If you are unfamiliar with updating firmware on your Wyse ThinOS cloud client, refer to Wyse Knowledge Base Solution #10566 (go to the Wyse Knowledge Base at http://www.wyse.com/kb

and search for 10566).

8 Chapter 2

Warning

. Use of the Software on more

A Inst alling Wyse Simple Imager 2.0.2

Caution

This appendix provides the detailed procedures yo u must complete to inst all W yse Simple Imager 2.0.2.

Pre-Installation Checklist

Before you begin installing Wyse Simple Imager, make sure you have met the requirements on this checklist for the machine to which Wyse Simple Imager will be installed:

Do not install Wyse Simple Imager on any machine which has Wyse Device Manager software installed.

• One of the following 32-bit Windows operating systems must be installe d (b e sure that all systems are up-to-date with current Microsoft service packs, patches, and updates):

· Windows 2003 Server Standard/Enterprise with SP2 or later

· Windows XP Pro with SP3 or later

Virtual machine environments are not supported.

• IIS with FTP and HTTP (World Wide Web Service) must be installed, enabled, and running.

• Any inexpensive external router with DHCP enabled must be connected to the machine and both the machine and router must be isolated.

Wyse Simple Imager must be installed and used on a machine (with a connected router running DHCP) that is isolated. Do not install Wyse Simple Imager on any machine which is connected to a network.

• Any existing previous version of Wyse Simple Imager must be uninstalled.

• A single network adapter is supported. If you have two adapters, you mu st disable one (for example, for a laptop with a wireless adapter, you must disable the wireless adapter).

• All software firewalls and antivirus services must be stopped.

• Place the Wyse Simple Imager 2.0.2 software (found on the Conversion Software Assembly DVD-ROM) into a folder on the machine.

10 Appendix A

Tip

Procedures

Be sure you have completed all pre-inst allation r equirement s as de scribed in "Pre-Installation Checklist" before you begin installing Wyse Simple Imager.

Step 1: Verify FTP Settings

1. Launch IIS (click Settings > Control Panel > Administrative Tools > Internet Information Services (IIS) Manager).

Figure 9 Launch IIS

2. In the IIS Manager screen, right-click Default FTP Site in the details pane and select Properties to open the Default FTP Site Properties dialog box.

If you cannot find the Default FTP Site option, verify that FTP services are installed (see "Pre-Installation Checklist").

Figure 10 Default FTP Site Properties

3. Click the Home Directory tab and ensure the following:

• A directory located on this computer option is selected

• Local path is C:\Inetpub\ftproot (this is the default path)

• Read, Write, and Log visits check boxes are selected

• MS-DOS option is selected

Installing Wyse Simple Imager 2.0.2 11

Caution

Step 2: Verify DHCP is Running

You can verify DHCP is running by going to Start > Control Panel > Network Connections, double-click your LAN connection (for example, Local Area Connection) to open the Local Area Connection Status dialog box, click the Support tab and then ensure that your Address Type is Assigned by DHCP. If this is not the case, you must correct the problem before continuing. If DHCP is not running do not install Wyse Simple Imager until it is running.

Figure 11 Local Area Connection Status dialog box

Step 3: Install Wyse Simple Imager

Navigate to the Wyse Simple Imager Release 2.0.2 folder on your hard drive (this is the location you selected in "Pre-Installation Checklist"), double-click the WSISetup.exe file to open the installation wizard, and then follow the prompts. It is recommended that you use the default settings provided during installation.

Be sure that the installation path is the same as the default path of the IIS FTP root path (for example, C:\Inetpub\ftproot).

Figure 12 Default installation path

After Wyse Simple Imager installation is complete, a Wyse Simple Imager icon will be created on the desktop from which the application can be run.

12 Appendix A

This page intentionally blank.

B Troubleshooting

Note

This appendix includes troubleshooting information.

For Wyse Customer Support information, see "Wyse Technical Support."

Problem Solution When attempting to image a cloud

client you receive an ARP Timeout error.

You are receiving Incompatible Firmware messages.

The new image was sent to the cloud client but the cloud client boots normally to the old firmware.

This means that the cloud client was unable to obtain an IP address from your DHCP server on the router (ARP means Address Resolution Protocol). This indicates a problem with your DHCP server on the router (see your router documentation to fix the problem).

Be sure you have the correct information in the Add Image dialog box as described in "Step 3: Use Wyse Simple Imager to Convert Each Cloud Client."

Use the following:

• Verify the boot order. Turn on the cloud client power , press and hold the DELETE key to enter the BIOS setup. When prompted, enter the password Fireport (cas e sensitive ). The first boot device should be set to PXE or LAN. If that is not the case, make the necessary changes.

• Verify that the FTP Server has the Write permission enabled (see "Step 1: Verify FTP Settings").

• Verify on the Wyse Simple Imager s erver: Go to Start > Run, enter cmd, and click OK. At the command prompt (c:>) enter ipconfig and press the Enter key: If you see an IP address of 127.0.0.1 anywhere, you have a loopback network condition. T o recover from this, uninstall Wyse Simple Imager ONLY, make sure you connect the Wyse Simple Imager server and the cloud client (with power applied to it, but NOT powered-on) to the router, and then re-install Wyse Simple Imager.

• Verify the directory structure is set to: c:\inetpub\ftproot\rapport c:\inetpub\ftproot\rapport\tools c:\inetpub\ftproot\rapport\tools\sa

• Remove any spaces in the firmware filename under C:\inetpub\ftproot\rapport\<product>. FTP does not recognize spaces.

14 Appendix B

Problem Solution When attempting to image a cloud

client you receive an Illegal TFTP operation error message.

When attempting to image a cloud client you receive a Boot file not found message.

Obtaining File not found error messages.

You are not obtaining an IP Address. In any case where you are not obtaining an IP Address, verify

Y ou are obtaining a PXE-E78 error on the cloud client and cannot re-image.

Use the following:

• If this is the first you are attempting to image using Wyse Simple Imager, more than likely this is an installation problem. Review the Wyse Simple Imager installation section and verify the installation process.

• If Wyse Simple Imager worked correctly in the past, try re-imaging a different cloud client. If the issue is resolved, you have a hardware problem and will need to send the defective cloud client to the Wyse service department for repair (see "Wyse Technical Support").

If you have a VPN client installed on the Wyse Simple Imager server, remove it and try again.

Verify that yo ur default FTP serv er ad dress is set correctly usin g the IIS Administration utility (see Microsoft documentation).

that the router DHCP server is up and running (see your router documentation to fix the problem).

PXE-E78 means Unable to locate boot server. The most common cause of this is when the Wyse Simple Ima ger server is installed by itself with no router running DHCP connected to the Wyse Simple Imager server. In such a case, you receive a loopback IP Address created for the proxy server in Wyse Simple Imager. Uninstall Wyse Simple Imager ONLY, make sure you connect the Wyse Simple Imager server and the router with DHCP running and then re-install Wyse Simple Imager.

When re-imaging a device, the cloud client reboots as normal to the original firmware.

You followed the usage instructions and still cannot image the cloud client.

When a device is imaged, two log files are created. These files will have the extensions of .log and either .fin or .end (these files are located in the following directory: C:\inetpub\ftproot\rapport\tools\sa\logs).

• .fin - Indicates a Successful imaging of the device

• .end - Indicates a Failure to image a device

• .log - Contains the Transaction information of the imaging process

To correct this problem, go to the Wyse Simple Imager console (see Figure 3), click Delete Logs, and then try re-imaging. You can also manually delete these files and try re-imaging again.

Uninstall Wyse Simple Imager and then re-install according to the instructions in this guide.

Troubleshooting 15

This page intentionally blank.

Installation Guide

Wyse

VX0LE Conversion to ThinOS

Issue: 070111

Written and published by: Wyse Technology Inc., July 2011

Created using FrameMaker

and Acrobat

Wyse Technology VX0LE User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Inst allation Guide

Copyright Notices

Content s

1 Introduction

Kit Contents

Wyse Technical Support

Related Documentation and Services

Wyse Online Community

Procedures: Using Wyse Simple Imager

Procedures: Using Wyse Device Manager

A Inst alling Wyse Simple Imager 2.0.2

Pre-Installation Checklist

Procedures

B Troubleshooting