WORX TOOLS WU641 User Manual [ru]

Pag 06

Pag 14

WU641

Finishing Sander ENG

Машина Плоскошлифовальная RUS

RU-WU641-M-060818.indd 1 2006-8-18 13:54:32

RU-WU641-M-060818.indd 2 2006-8-18 13:54:32

RU-WU641-M-060818.indd 3 2006-8-18 13:54:33

11

5

6

10

7

8

9

1

2

3

4

RU-WU641-M-060818.indd 4 2006-8-18 13:54:34

A B C.1

C.2

C.3 D

E.1 E.2 F

RU-WU641-M-060818.indd 5 2006-8-18 13:54:36

Finishing Sander ENG

1. ON-OFF SWITCH

2. SWITCH LOCK-ON BUTTON

3. VARIABLE SPEED CONTROL DIAL

4. HAND GRIP AREA

5. BASEPLATE

6. SANDING PAPER CLAMP

7.

CLAMP LEVER

8.

CLAMP LEVER LOCK

9.

DUST BAG

10. PAPER PUNCH

11. HOOK AND LOOP SYSTEM

RU-WU641-M-060818.indd 6 2006-8-18 13:54:38

Finishing Sander ENG

TECHNICAL DATA

Rated Voltage 220V-240V ~ 50Hz/60Hz

Rated Power 350W

Rated No-load speed 6,000-11,000min

-1

Base plate size 113 x 225mm

Orbital dia 2.4mm

Double insulation

Machine weight 2.8Kg

NOISE AND VIBRATION DATA

A weighted sound pressure 80dB (A)

A weighted sound power 93dB (A)

Wear ear protection when sound pressure is over 85dB (A)

Typical weighted vibration 4.16m/s

2

ACCESSORIES

Paper hole punch 1pc
Dust bag 1pc
Sanding Papers 1pc (120#)
Vacuum Adaptor 1pc
If using sanding paper without dust holes, you must use the paper punch to make
holes.
Use 1/2 sheet sanding paper of the following size:
Paper size: 115 x 280 mm for no hook & loop (clamp only)
115 x 225mm for hook & loop

We recommend that you buy all your accessories from the store where you purchased the tool.
Use good quality accessories marked with a well-known brand name. Choose the grade according
to the work you intend to undertake. Refer to the accessory packaging for further details. Store
personnel can also help and advise.

0706

RU-WU641-M-060818.indd 7 2006-8-18 13:54:39

Finishing Sander ENG

SAFETY INSTRUCTIONS

WARNING!

Read all instructions Failure to follow
all instructions listed below may result in
electric shock, fire and/or serious injury. The
term“power tool”in all of the warnings listed
below refers to your mains-operated (corded)
power tool or battery-operated (cordless)
power tool.

SAVE THESE INSTRUCTIONS

1. WORK AREA
a) Keep work area clean and well lit.

Cluttered and dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence
of flammable liquids, gases or dust.

Power tools create sparks which may ignite
the dust or fumes.

c) Keep children and bystanders away

while operating a power tool. distractions

can cause you to lose control.

2. ELECTRICAL SAFETY
a) Power tool plugs must match the

outlet. Never modify the plug in any way.

Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of
electric shock

b) Avoid body contact with earthed or

grounded surfaces such as pipes,
radiators, ranges and refrigerators.

There is an increased risk of electric shock if
your body is earthed or grounded.

c) Do not expose power tools to rain or

wet conditions. Water entering a power

tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the

cord for carrying, pulling or unplugging
the power tool. Keep cord away from

heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.

e) When operating a power tool outdoors,

use an extension cord suitable for
outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric
shock.

3. PERSONAL SAFETY
a) Stay alert, watch what you are doing

and use common sense when operating
a power tool. Do not use a power tool

while you are tired or under the influence
of drugs, alcohol or medication. A moment
of inattention while operating power tools
may result in serious personal injury.

b) Use safety equipment. Always wear

eye protection. Safety equipment such as

dust mask, non-skid safety shoes, hard hat,
or hearing protection used for appropriate
conditions will reduce personal injuries.

c) Avoid accidental starting. Ensure the

switch is in the off-position before plugging
in. Carrying power tools with your finger on
the switch or plugging in power tools that
have the switch on invites accidents.

d) Remove any adjusting key or wrench

before turning the power tool on. A

wrench or a key left attached to a rotating
part of the power tool may result in personal
injury.

e) Do not overreach. Keep proper

footing and balance at all times. This

enables better control of the power tool in
unexpected situations.

f) Dress properly. Do not wear loose clothing

or jewellery. Keep your hair, clothing and
gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught
in moving parts.

g) If devices are provided for the

connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use

of these devices can reduce dust-related
hazards.

4. POWER TOOL USE AND CARE
a) Do not force the power tool. Use the

correct power tool for your application. The
correct power tool will do the job better and
safer at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power

tool that cannot be controlled with the
switch is dangerous and must be repaired.

c) Disconnect the plug from the power

source before making any adjustments,

RU-WU641-M-060818.indd 8 2006-8-18 13:54:40