Page 1
GUTTERPRO Universal Gutter Cleaning Kit EN
Trousse de nettoyage de gouttières GUTTERPRO F
Kit de limpieza de canales GUTTERPRO ES
HELPLINE NUMBER
HELPLINE NUMBER
1-866-354-WORX (9679)
WA4092
P06
P07
P09
Page 2
Fits all brands of blower/vacs up to 5” in diameter
s'adapte à toutes les marques de souffleurs aspirateurs de 5'' de
diamètre
Sirve para todo tipo de extractores/aspiradoras de hasta de 5” de
diámetro (12,7 cm)
Page 3
Page 4
1
2
2
2
3
4
1. GUTTER TUBE NOZZLE (QUANTITY OF 1)
2. GUTTER TUBE EXTENSION (QUANTITY OF 3)
3. GUTTER TUBE ADAPTER (QUANTITY OF 1)
4. UNIVERSAL ADAPTOR
Page 5
1 2
2
3 4
A1
B2
2
B1.1
B1
B3
B4
C
D
Page 6
SAFETY INSTRUCTIONS
WARNING! User must read the product
manual to fully understand this product
prior to use, and follow all safety instructions
as outlined in the WORXAIRTM Operator’s
Manual.
CAUTION!The user must wear the
appropriate clothing and safety goggles
when operating this product. Be aware of all
bystanders, pets and objects in a close
proximity.
• DO NOT operate blower and attachments
when fatigued.
• DO NOT overreach or stand on unstable
support. Keep good footing and balance at
all times.
• Never direct airflow towards bystanders.
Always be aware of the direction that the
debris will be thrown.
• Use a face filter mask to avoid breathing
dust and debris.
WARNING: This product maybe contains
lead, phthalate or other chemicals known to
6
the State of California to cause cancer, birth
defects and other reproductive harm. Please
wash your hands after use.
ASSEMBLY AND OPERATION
1. ATTACH THE GUTTER KIT AS SHOWN
IN Fig. A1:
Connect the (1, 2, 3) components by screwing
together. Snap the (3, 4) components together.
(2) Check to make sure the strap is threaded
through the locking mechanism. Then
pull to tighten the strap (B2). Increase the
tension by pulling the latch up and down
to tighten (B3). To loosen, simply press the
two outside latches down and then pull the
strap out from other side (B4).
(3) Test that the Universal Adapter will not
slide off of the blower outlet.
(4) If further tightening is needed, then pull the
middle latch up and down until the adapter
is tight. Please recheck if it will slide off of
the blower outlet. Realign and repeat these
steps if needed (B3). To loosen, simply
press the two outside latches down and
then pull the strap out from other side (B4).
PLEASE NOTE: The Universal Adapter may
have space between the Blower Outlet and
Adapter Outlet after installation.
To remove the adapter, simply press the two
outside latches down and loosen the strap to
remove it from the Blower Outlet (B4).
NOTE:
Use only enough Gutter Tube Extensions to
comfortably reach the inside of the gutter.
3. OPERATE ACCORDING TO Fig. C:
The Gutter Tube Nozzle can be adjusted to any
desired direction by rotating the Gutter Tube
Connecter as shown in Fig. D. Gutter cleaning
applications will vary. It is recommended to
try various positions to find the most effective
working position for the type of house and
gutter design.
2.
ASSEMBLING THE UNIVERSAL ADAPTOR
(1) Place the fabric side of the Universal
Adapter over the Blower Outlet and slide it
on as far as possible (B1).
(a) WORX TRIVAC models - Place the fabric
side of the Universal Adapter over the
Vacuum Outlet and slide it on as far as
possible (B1.1). Before operation, flip the
blow/vac switch into the vacuum mode.
PLEASE NOTE: Items can be vacuumed
through the vac inlet and pass through or
clog the gutter kit. Please keep the vac inlet
away from objects while using the gutter
kit.
GUTTERPRO Universal
Gutter Cleaning Kit
EN
Page 7
Designed in Italy. Made in China
Conçu en Italie. Fabriqué en Chine
Diseñado en Italia. Fabricado en China
Copyright © 2013, Positec. All Rights Reserved.
2CBV80APK11002A0
Loading...