Worx WG801.9, WG801 User Manual

20V Cordless Shrub Shear & Grass Shear

WG801 WG801.9

P02

P10

P15

WARNING: Some dust created by power

sanding, sawing, grinding, drilling and other
construction activities contains chemicals known to
the state of California to cause cancer, birth defects
or other reproductive harm. Some examples of these
chemicals are:

● Lead from lead-based paints;

● Crystalline silica from bricks and cement and

other masonry products;

● Arsenic and chromium from chemically-treated

lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemical: work in a well ventilated
area, and work with approved safety equipment,
such as those dust masks that are specially designed
to filter out microscopic particles.

WARNING: This product can expose you

to chemicals including lead, phthalate or
bisphenol A which are known to the State of
California to cause cancer, birth defects or other
reproductive harm. Wash your hands after use. For
more information go to www.P65Warnings.ca.gov.

GENERAL POWER TOOL
SAFETY WARNINGS

WARNING: Read all safety warnings and

instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or

2

serious injury.

Save all warnings and instructions for future
reference.

The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery­operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

b) Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while

operating a power tool. Distractions can cause
you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts.

Damaged or entangled cords increase the risk of

electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.

f) If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk
of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
moment of inattention while operating power
tools may result in serious personal injury.

b) Use personal protective equipment. Always wear

eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will
reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger
on the switch or energising power tools that have
the switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control of
the power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery
or long hair can be caught in moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct

power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.

c) Disconnect the plug from the power source and/

or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety

20V Cordless Shrub Shear & Grass Shear EN

measures reduce the risk of starting the power
tool accidentally.

d) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool.

Power tools are dangerous in the hands of

untrained users.

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one
type of battery pack may create a risk of fire when
used with another battery pack.

b) Use power tools only with specifically designated

battery packs. Use of any other battery packs may
create a risk of injury and fire.

c) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together
may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified

repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.

HEDGE TRIMMER SAFETY
WARNINGS

1. Keep all parts of the body away from the

cutter blade. Do not remove cut material
or hold material to be cut when blades
are moving. Make sure the switch is off
when clearing jammed material. Blades
coast after turn off. A moment of inattention

while operating the hedge trimmer may result in
serious personal injury.

2. Carry the hedge trimmer by the handle
with the cutter blade stopped. When
transporting or storing the hedge trimmer
always fit the cutting device cover. Proper

handling of the hedge trimmer will reduce
possible personal injury from the cutter blades.

3. Hold the power tool by insulated gripping
surfaces only, because the cutter blade
may contact hidden wiring or its own cord.

Cutter blades contacting a live wire may make
exposed metal parts of the power tool live and
could give the operator an electric shock

4. Keep hands away from blade. Contact with
blade will result in serious personal injury.

5. Use both hands when operating the hedge
trimmer. Using one hand could cause loss
of control and result in serious personal
injury.

6. Only use with handle and guard properly
assembled to hedge trimmer. The use of the
hedge trimmer without the proper guard
or handle provided may result in serious
personal injury.

7. Check the hedge for foreign objects, e.g.
wire fences.

Important Safety Instructions

WARNING: When using electric gardening

appliances, basic safety precautions should
always be followed to reduce the risk of fire, electric
shock, and personal injury, including the following:

WARNING: Read all instructions

FOR ALL APPLIANCES

1) Avoid Dangerous Environment - Don’t use

appliances in damp or wet locations.

2) Don’t Use In Rain.

3) Keep Children Away - All visitors should be kept

at a distance from work area.

4) Dress Properly - Do not wear loose clothing or

jewelry. They can be caught in moving parts.
Use of rubber gloves and substantial footwear
is recommended when working outdoors. Wear
protective hair covering to contain long hair.

5) Use Safety Glasses - Always use face or dust

mask if operation is dusty.

6) Use Right Appliance - Do not use appliance for

any job except that for which it is intended.

7) Don’t grasp the exposed cutting blades or cutting

edges when picking up or holding the appliance.

8) Don’t Force Appliance - It will do the job better

and with less likelihood of a risk of injury at the
rate for which it was designed.

9) Don’t Overreach - Keep proper footing and

balance at all times.

10) Stay Alert - Watch what you are doing. Use

common sense. Do not operate appliance when

3

20V Cordless Shrub Shear & Grass Shear EN

you are tired.

11) Store Idle Appliances Indoors - When not in use,
appliances should be stored indoors in dry, and
high or locked-up place - out of reach of children.

12) Maintain Appliance With Care - Keep cutting
edge sharp and clean for best performance and
to reduce the risk of injury. Follow instructions
for lubricating and changing accessories. Keep
handles dry, clean, and free from oil and grease.

13) Check Damaged Parts - Before further use of the
appliance, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other condition that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced
by an authorized service center unless indicated
elsewhere in this manual.

FOR ALL BATTERY – OPERATED GARDENING
APPLIANCES

1. For all battery-operated gardening
appliances:

a) Do not charge appliance in rain, or in wet

locations.

b) Do not use battery-operated appliance in rain.
c) Remove or disconnect battery before servicing,

cleaning or removing material from the

4

gardening appliance.

2. For all battery-operated products employing
a detachable or separable battery:

a) Use only the following type and size

battery(ies):¬¬¬ WA3520, WA3525, WA3575,
WA3578

b) Do not dispose of the battery(ies) in a fire. The cell

may explode. Check with local codes for possible
special disposal instructions.

c) Do not open or mutilate the battery(ies). Released

electrolyte is corrosive and may cause damage to
the eyes or skin. It may be toxic if swallowed.

d) Exercise care in handling batteries in order not

to short the battery with conducting materials
such as rings, bracelets, and keys. The battery or
conductor may overheat and cause burns.

3. Avoid unintentional starting – Do not insert the
battery with your finger on the switch. Be sure
the switch is off when inserting the battery.

SAVE THESE INSTRUCTIONS

Additional safety rule for grass shear

Keep hands away from blades.

SAFETY WARNINGS FOR
BATTERY PACK

1) WARNING: Risk of fire and burns. Do not
disassemble, heat above 100°C (212°F), or
incinerate. Do not expose cells or batteries
to heat or fire. Avoid storage in direct
sunlight.

2) Dispose of used battery promptly.. When
disposing of secondary cells or batteries,
keep cells or batteries of different
electrochemical systems separate from
each other.

3) Keep battery out of reach of children and in
original package until ready to use.

4) Never put batteries in mouth. If swallowed,
contact your physician or local poison
control center.

5) CAUTION – The battery used in this device
may present a risk of fire or chemical burn
if mistreated. Replace battery with WORX
WA3520, WA3525, WA3575, WA3578 only.
Use of another battery may present a risk
of fire or explosion.

6) Warning: Do not use a visibly damaged
battery pack or appliance as applicable.

7) Warning: Do not modify or attempt to
repair the appliance or the battery pack as
applicable.

8) BATTERY MUST BE RECYCLED.

9) Do not short-circuit a cell or battery. Do
not store cells or batteries haphazardly in
a box or drawer where they may short­circuit each other or be short-circuited by
conductive materials.

10)Do not subject cells or batteries to
mechanical shock.

11)Keep cells and batteries clean and dry.

Wipe the cell or battery terminals with a clean dry
cloth if they become dirty.

12) Do not maintain secondary cells and
batteries on charge when not in use.

13) Retain the original cell and battery
literature for future reference.

14) Do not use any charger other than that
specifically provided for use with the
equipment. Secondary cells and batteries
need to be charged before use. Always

use the correct charger and refer to the
manufacturer’s instructions or equipment manual
for proper charging instructions.

15) When possible, remove the battery from the
equipment when not in use.

16) Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to battery
pack, picking up or carrying the appliance.
Carrying the appliance with your finger on the
switch or energizing appliance that have the
switch on invites accidents.

17) Disconnect the battery pack from the appliance
before making any adjustments, changing
accessories, or storing appliance. Such

20V Cordless Shrub Shear & Grass Shear EN

preventive safety measures reduce the risk of
starting the appliance accidentally.

18) Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause
irritation or burns.

19) Have servicing performed by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the product is
maintained.

SYMBOL

To reduce the risk of injury, user
must read instruction manual

Warning

Wear ear protection

Unlock

POSITEC Inc. has established a
partnership with the RBRC Cor­poration to recycle any Positec
batteries with the RBRC-call2re­cycle seal. For environmental
protection, please do not discard
batteries in the trash. After the
batteries’ life cycle is ended, then
please call 1-800-822-8837 for
a free service that will properly
dispose of the battery.

Li-I on

Wear eye protection

5

Wear dust mask

Do not expose to rain

DANGER – Keep hands away
from blade

Li-Ion battery, battery must be
recycled

Make sure the battery is removed
prior to changing accessories.

Wear protective gloves

Lock

20V Cordless Shrub Shear & Grass Shear EN

4

3

2

1

5

6

6

7

8

9

20V Cordless Shrub Shear & Grass Shear EN

1. GRASS SHEAR BLADE

2. LOCK-OFF BUTTON

3. HANDLE

4. BATTERY PACK RELEASE BUTTON *

5. BATTERY PACK *

6. ON/OFF SWITCH

7. TOOL-FREE DRIVE COVER

8. TOOL-FREE DRIVE COVER RELEASE BUTTON

9. SHRUB SHEAR BLADE

*Not all the accessories illustrated or
described are included in standard delivery.

TECHNICAL DATA

WG801 WG801.9

Volt ag e 20V

No Load Speed 110 0 rpm

Cutting width 4” with grass shear blade

Cutting length 8” with shrub blade

Max. cutting
diameter

Charging time 5 hrs /

Charger rating

Machine weight:
(with grass
shear blade)

*Voltage measured without workload. Initial
battery voltage reaches maximum of 20 volts.
Nominal voltage is 18 volts.

0.3” for shrub blade

Input: 120V~ 60Hz

Output: 20V

400mA

2.0 lbs 1.3 lbs

/

ACCESSORIES

WG801 WG801.9

4” Grass Shear
Blade

8” Shrub Shear
Blade

Battery Pack
(WA3575)

Charger (WA3742) 1 /

Telescopic Pole
(WA0040)

We recommend that you p urchase your accessories
listed in the ab ove lis t from the same store that sold
you the tool. Refer to the accessory packaging for
further details. Store per sonnel can assis t you and
offer advice.

1 1

1 1

1 /

/ /

7

20V Cordless Shrub Shear & Grass Shear EN

A1

A2

1

2

1

B1

8

B2

D

CLICK!

C1

C2

D

1

100 %

2

0%

2´

20V Cordless Shrub Shear & Grass Shear EN

C3

C4

1

2

D

F

E

D

1

9

2

20V Cordless Shrub Shear & Grass Shear EN

OPERATING INSTRUCTIONS

NOTE: Before using the tool, read the
instruction book carefully.

INTENDED USE

The product is intended for light trimming of shrubs
and lawn edges in domestic use.

ASSEMBLY AND OPERATION

ACTION FIGURE

ASSEMBLY (Fitting/Changing the blade)

Removing the blade

WARNING: Wear gloves when
changing the blade.

Fitting the blade

BEFORE OPERATION

Checking the battery condition (for
WG801)

Charging the battery pack
More details can be found in
charger’s manual

Installing the battery pack See Fig. C3

10

Removing the battery pack Se e Fig. C 4

OPERATION

Starting& Stopping See Fig. D

Trimming grass
NOTE: Keep the tool away from hard
objects and delicate plants. To make a
closer cut, slightly tilt the tool.

Trimming hedges and shrubs
NOTE: Take care to avoid any foreign
objects. Especially avoid hard objects
such as metal wire and railings, as
these could damage the blades.

See Fig.
A1, A2

See Fig.
B1, B2

See Fig. C1

See Fig. C2

See Fig. E

See Fig. F

MAINTENANCE

NOTE: To ensure long and reliable service, carry out
the following maintenance regularly.
Remove the battery before carrying out any
adjustment, servicing or maintenance.
Check for obvious defects such as loose, dislodged
or damaged blade, loose fixings and worn or
damaged components.
Check that covers and guards are undamaged and
correctly fitted. Carry out necessary maintenance or
repairs before using.

FOR BATTERY TOOLS

The ambient temperature range for the use and
storage of tool and battery is 0
The recommended ambient temperature range for
the charging system during charging is 0

BLADE MAINTENANCE

Always clean the cutting blades after operation and
periodically lubricating the cutting blade.
Visually check the condition of the cutting edges of
the cutting blade.
Ensure that the blade is covered with the blade guard
supplied when not in use.

CLEANING/STORAGE

Clean the exterior of the machine thoroughly using
a soft brush and cloth. Do not use water, solvents
or polishes. Remove all debris, especially from the
ventilation slots.
Store the machine in a secure dry place out of reach
of children. Do not place other objects on top of the
machine.

o

C-45oC.

o

C-40oC.

20V Cordless Shrub Shear & Grass Shear EN