SAFETY AND OPERATING MANUAL
ORIGINAL INSTRUCTIONS
All-in-One blower/vac/mulcher WG505E
3
Click!
2
1
11
5
4
7
8
6
A B1
9
10
Click!
B2
1
C
D1 D2
OFF
ON
E
Click!
F1 F2
F3 G1
G2 H1
2
1
Click!
2
1
H2 H3
G2 H1
I1 I2
2
1. HANDLE
2. ON /OFF SWITCH
3. SAFETY LOCK KNOB
4. UPPER VACUUM TUBE
5. LOWER VACUUM TUBE
6. LEAF COLLECTION BAG
7. BLOWER TUBE
8. VARIABLE BLOWER SPEED KNOB
9. BLOWER/ VACUUM SELECTOR LEVER
10. QUICK RELEASE BAG COLLAR
11. MOTOR HOUSING
Not all the accessories illustrated or
described are included in standard delivery.
TECHNICAL DATA
Type WG505E(5-designation of machinery,
representative of Electric Blower Vacuum)
Voltage 220-240V~50/60Hz
6
Power input 3000W
No load speed 15000/min
Air capacity 10m
Air speed 128-335Km/h
Mulching rate 16:1
Collection bag capacity 45L
Machine Weight 4.1kg
Protection class
NOISE DATA
3
/min
VIBRATION INFORMATION
Typical weighted vibration ah=3.2m/s
Uncertainty K=1.5m/s²
The declared vibration total value may be used for
comparing one tool with another, and may also be
used in a preliminary assessment of exposure.
WARNING! The vibration emission value
during actual use of the power tool can differ
from the declared value depending on the ways in
which the tool is used dependant on the following
examples and other variations on how the tool is
used:
How the tool is used and the materials being cut or
drilled.
The tool being in good condition and well
maintained
Using the correct accessory for the tool and ensuring
it is sharp and in good condition.
The tightness of the grip on the handles and if any
anti vibration accessories are used.
And the tool is being used as intended by its design
and these instructions.
This tool may cause hand-arm vibration
syndrome if its use is not adequately managed.
WARNING! To be accurate, an estimation of
exposure level in the actual conditions of use
should also take account of all parts of the operating
cycle such as the times when the tool is switched off
and when it is running idle but not actually doing the
job. This may significantly reduce the exposure level
over the total working period.
Helping to minimise your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades
Maintain this tool in accordance with these
instructions and keep well lubricated (where
appropriate)
If the tool is to be used regularly then invest in anti
vibration accessories.
/II
Avoid using tools in temperatures of 10
Plan your work schedule to spread any high
vibration tool use across a number of days.
0
C or less
2
A weighted sound pressure L
: 3dB(A)
K
pA
A weighted sound power L
Wear ear protection
: 94dB(A)
pA
:110dB(A)
wA
ACCESSORIES
Leaf collection bag 1
We recommend that you purchase your accessories
from a WORX authorized dealer or service center.
Choose the type according to the work you intend
to undertake. Refer to the accessory packaging for
further details. Store personnel can assist you and
offer advice.
All-in-One blower/vac/mulcher WG505E
PRODUCT SAFETY
GENERAL SAFETY WARNINGS
WARNING: Read all
safety warnings and all
instructions. Failure to follow
the warnings and instructions
may result in electric shock, fire
and/or serious injury.
Save all warnings and
instructions for future
reference.
If the supply cord is damaged,
it must be replaced by the
manufacturer, its service agent
or similarly qualified persons in
order to avoid a hazard.
IMPORTANT
READ CAREFULLY BEFORE
USE.
KEEP FOR FUTURE
REFERENCE.
Safe operating practices
1) Training
a) Read the instructions carefully.
Be familiar with the controls
and the correct use of the
machine.
b) Never allow children, persons
with reduced physical, sensory
or mental capabilities or lack
of experience and knowledge
or people unfamiliar with
these instructions to use the
machine, local regulations
may restrict the age of the
operator.
c) Never operate the machine
while people, especially
children, or pets are nearby.
d) Keep in mind that the operator
or user is responsible for
accidents or hazards occurring
to other people or their
property.
2) Preparation
a) While operating the machine,
always wear substantial
footwear and long trousers.
Do not operate the machine
when barefoot or wearing
open sandals. Avoid wearing
clothing that is loose fitting or
that has hanging cords or ties.
b) Do not wear loose clothing or
jewellery that can be drawn
into the air inlet. Keep long
hair away from the air inlets.
Obtain ear protection and safety
c)
glasses. Wear them at all times
while operating the machine.
d) Operate the machine in a
recommended position and
only on a firm, level surface.
e) Do not operate the machine
on a paved or gravel surface
where ejected material could
cause injury.
f) Before using, always visually
inspect to see, that the
shredding means, shredding
means bolts and other
fasteners are secure, the
housing is undamaged and
that guards and screens are
in place. Replace worn or
damaged components in sets
to preserve balance. Replace
damaged or unreadable
labels.
7
All-in-One blower/vac/mulcher WG505E
g) Before use, check the supply
and extension cord for signs
of damage or aging. If the
cord becomes damaged
during use, disconnect
the cord from the supply
immediately. DO NOT
TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY.
Do not use the machine if the
cord is damaged or worn.
h) Keep extension cords away
from moving hazardous parts
to avoid damages to the cords
which can lead to contact with
live parts.
i) If an extension cord is used
make sure it is for outdoor
use and marked as such.
The recommended size of
8
extension cord is not lighter
2
than 1mm
.
3) Operation
a) Before starting the machine,
make certain that the feeding
chamber is empty.
b) Keep your face and body away
from the feed intake opening.
c) Do not allow hands or any
other part of the body or
clothing inside the feeding
chamber, discharge chute, or
near any moving part.
d) Keep proper balance and
footing at all times. Do not
overreach. Never stand at a
higher level than the base of
the machine when feeding
material into it.
e) Always stand clear of
the discharge zone when
operating this machine.
f) When feeding material into
the machine be extremely
careful that pieces of metal,
rocks, bottles, cans or other
foreign objects are not
included.
g) If the cutting mechanism
strikes any foreign objects or
if the machine should start
making any unusual noise
or vibration, immediately
shut off the power source
and allow the machine to
stop. Disconnect the machine
from the supply and take
the following steps before
restarting and operating the
machine:
i) inspect for damage;
ii) replace or repair any
damaged parts;
iii) check for and tighten any
loose parts.
h) Do not allow processed
material to build up in the
discharge zone; this may
prevent proper discharge
and can result in kickback of
material through the intake
opening.
i) If the machine becomes
clogged, shut-off the power
source and disconnect the
machine from supply before
cleaning debris.
j) Never operate the machine
with defective guards or
shields, or without safety
devices, for example debris
collector in place.
k) Keep the power source
All-in-One blower/vac/mulcher WG505E
clean of debris and other
accumulations to prevent
damage to the power source
or possible fire.
Do not transport this machine
l)
while the power source is running.
m) Stop the machine, and remove
plug from the socket. Make
sure that all moving parts
have come to a complete stop
- Whenever you leave the
machine,
- Before clearing blockages or
unclogging chute,
- Before checking, cleaning or
working on the machine.
n) Avoid using the machine
in bad weather conditions
especially when there is a risk
of lightning.
4) Maintenance and storage
a) Keep all nuts, bolts and
screws tight to be sure the
appliance is in safe working
condition;
b) Check the debris collector
frequently for wear or
deterioration.
c) Replace worn or damaged
parts.
d) Use only genuine replacement
parts and accessories.
e) Store the machine in a dry
place out of the reach of
children.
f) When the machine is stopped
for servicing, inspection,
or storage, or to change
an accessory, shut off the
power source, disconnect the
machine from the supply and
make sure that all moving
parts are come to a complete
stop. Allow the machine
to cool before making any
inspections, adjustments, etc.
Maintain the machine with
care and keep it clean.
Store the machine in a dry place
g)
out of the reach of children.
h) Always allow the machine to
cool before storing.
i) When servicing the shredding
means be aware that, even
though the power source
is switched off due to the
interlock feature of the guard,
the shredding means can still
be moved.
j) Never attempt to override
the interlocked feature of the
guard.
5) Additional safety
instructions for units with
bagging attachments
Switch-off the machine before
attaching or removing the bag.
6) Recommendation
The machine should be
supplied via a residual current
device (RCD) with a tripping
current of not more than
30mA.
SYMBOLS
Read the operator’s manual.
9
All-in-One blower/vac/mulcher WG505E
10
Wear eye protection
Wear ear protection
Double insulation
Disconnect the mains plug if the cord
becomes damaged or entangled
SWITCH OFF: Remove plug
from mains before cleaning or
maintenance.
Keep bystanders away
Warning of hazard
Do not expose to rain
Blow mode
Vacuum mode
Impeller continues to rotate after the
machine is switched off. Wait until all
machine components have completely
stopped before touching them.
Lock
Unlock
Waste electrical products must not be
disposed of with household waste.
Please recycle where facilities exist.
Check with your local authorities or
retailer for recycling advice.
OPERATION
INTENDED USE:
The blower & Vac is intended for residential use only.
Use the blower outdoors to move or vacuum yard
debris as needed.
ASSEMBLY AND OPERATION
ACTION FIGURE
Blow mode
Assembling the Blower/
Vacumm Tube
WARNING: Make sure the
ON/OFF switch is in the
OFF Position before tightening
the safety lock knob.
WARNING: Do not loosen
the safety lock knob
rapidly. Turn the knob with
normal speed. Take the turning
time not less than 15s to ensure
the moving parts completely
stop before taking apart the
vacuum tube.
Starting & Stopping See Fig. C
Using the Blower See Fig. D1 & D2
Adjusting the Blowing Speed See Fig. E
Vaccumming
Attaching the Leaf Collection
Bag
Starting & Stopping See Fig. C
Using the Vacuum See Fig. G1 &G2
Emptying the Leaf Collection
Bag
Removing Clogged Debris from
the Impeller(no tool included)
WARNING: Make sure the
ON/OFF switch is in the
OFF Position before loosening
the safety lock knob.
See Fig. A &
B1&B2
See Fig. F 1&
F2& F3
See Fig. H1&
H2&H3
See Fig. I1&I2
STORAGE
Store the Blower/Vacuum and extension cord
indoors, in a cool dry location, out of reach of
children and animals.
All-in-One blower/vac/mulcher WG505E
TROUBLE SHOOTING
Problems Possible Causes Corrective Action
The Blower/
Vac does not
operate.
The Blower/
Vac jammed or
clogged.
The Blower/Vacuum Tube is not attached to the
Motor Housing.
Power cord is not connected to the power source.
Debris blocking in the Impeller
Debris blocking in the Blower/Vacuum Tube or
the connection of the Leaf Collection Bag.
Attach the Blower/ Vacuum Tube to the
Motor Housing.
Connect the power cord to a power source.
Remove clogged debris from the Impeller.
Remove clogged debris from the Blower
/Vacuum Tube or the connection of the
Leaf Collection Bag.
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be
disposed of with household waste. Please
recycle where facilities exist. Check with your
local authorities or retailer for recycling advice.
PLUG REPLACEMENT
(UK & IRELAND ONLY)
If you need to replace the fitted plug then follow the
instructions below.
IMPORTANT
The wires in the mains lead are colored in
accordance with the following code:
Blue = Neutral
Brown = Live
As the colors of the wires in the mains lead of this
appliance may not correspond with the coloured
markings identifying the terminals in your plug,
proceed as follows. The wire which is coloured blue
must be connected to the terminal which is marked
with N. The wire which is coloured brown must be
connected to the terminal which is marked with L.
WARNING! Never connect live or neutral wires
to the earth terminal of the plug. Only fit an
approved BS1363/A plug and the correct rated fuse.
NOTE: If a moulded plug is fitted and has to be
removed take great care in disposing of the plug
and severed cable, it must be destroyed to prevent
engaging into a socket.
DECLARATION OF
CONFORMITY
We,
Positec Power Tools (Europe) Ltd,
PO Box 6242 Newbury RG14 9LT UK
Declare that the product,
Description Electric Blower Vacuum
Type WG505E(5-designation of machinery,
representative of Electric Blower Vacuum)
Function Blowing and picking up debris into a
debris collector
Complies with the following Directives,
2006/42/EC, 2014/30/EU, 2011/65/EU,
2000/14/EC amended by 2005/88/EC
2000/14/EC amended by 2005/88/EC:
- Conformity Assessment Procedure as per
Annex V
- Measured Sound Power Level 106.7dB(A)
- Declared Guaranteed Sound Power Level
110dB(A)
Standards conform to
EN 60335-1 EN 50636-2-100
EN ISO 3744 EN 62233
EN 55014-1 EN 55014-2
EN 61000-3-2 EN 61000-3-3
The person authorized to compile the technical file,
Name Russell Nicholson
Address Positec Power Tools (Europe) Ltd,
PO Box 6242 Newbury RG14 9LT UK
11
Suzhou 2016/09/27
Allen Ding
Deputy Chief Engineer, Testing & Certification
All-in-One blower/vac/mulcher WG505E
After-sales Service and Application
At www.worx.com you can order spare parts or
arrange the collection of a product in need of servicing
or repair.
Tel. Service: 0345 202 9679
E-Mail: customerservices@worxtools.com
www.worx.com
Copyright © 2016, Positec. All Rights Reserved.
AR01265100
Loading...