Page 1
SAFETY AND OPERATING MANUAL
ORIGINAL INSTRUCTIONS
Cordless Hedge Trimmer WG268E WG268E.9
Page 2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING Read all safety warnings
and all instructions. Failure to follow
the warnings and instructions may result in
electric shock, fire and/or serious injury.
suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tool in a damp
location is unavoidable, use a residual
current device (RCD) protected
supply. Use of an RCD reduces the risk of
electric shock.
Save all warnings and instructions for
future reference.
The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in
explosive atmospheres, such as in the
presence of flammable liquids, gases
or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders
away while operating a power tool.
2
Distractions can cause you to lose control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the
outlet. Never modify the plug in any
way. Do not use any adapter plugs
with earthed (grounded) power tools.
Unmodified plugs and matching outlets
will reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes,
radiators, ranges and refrigerators.
There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or
wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep cord
away from heat, oil, sharp edges or
moving parts. Damaged or entangled
cords increase the risk of electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a cord
3) PERSONAL SAFETY
a) Stay alert, watch what you are
doing and use common sense when
operating a power tool. Do not use
a power tool while you are tired or
under the influence of drugs, alcohol
or medication. A moment of inattention
while operating power tools may result in
serious personal injury.
b) Use personal protective equipment.
Always wear eye protection. Protective
equipment such as dust mask, nonskid safety shoes, hard hat, or hearing
protection used for appropriate conditions
will reduce personal injuries.
c) Prevent unintentional starting. Ensure
the switch is in the off-position before
connecting to power source and/or
battery pack, picking up or carrying
the tool. Carrying power tools with your
finger on the switch or energising power
tools that have the switch on invites
accidents.
d) Remove any adjusting key or wrench
before turning the power tool on. A
wrench or a key left attached to a rotating
part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper
footing and balance at all times. This
enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your
hair, clothing and gloves away from
moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g)
If devices are provided for the
connection of dust extraction and
collection facilities, ensure these are
connected and properly used. Use of dust
collection can reduce dust-related hazards.
Cordless Hedge Trimmer WG268E WG268E.9
Page 3
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool will
do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the
switch does not turn it on and off. Any
power tool that cannot be controlled
with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments, changing accessories, or
storing power tools. Such preventive
safety measures reduce the risk of
starting the power tool accidentally.
d) Store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to operate
the power tool. Power tools are
dangerous in the hands of untrained
users.
e) Maintain power tools. Check for
misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power
tool’s operation. If damaged, have
the power tool repaired before use.
Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with
sharp cutting edges are less likely to
bind and are easier to control.
g) Use the power tool, accessories and
tool bits etc. in accordance with these
instructions, taking into account the
working conditions and the work to
be performed. Use of the power tool for
operations different from those intended
could result in a hazardous situation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger
specified by the manufacturer. A
charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically
designated battery packs. Use of any
other battery packs may create a risk of
injury and fire.
c) When battery pack is not in use, keep
it away from other metal objects, like
paper clips, coins, keys, nails, screws
or other small metal objects, that can
make a connection from one terminal
to another. Shorting the battery terminals
together may cause burns or a fire.
d) Under abusive conditions, liquid
may be ejected from the battery;
avoid contact. If contact accidentally
occurs, flush with water. If liquid
contacts eyes, additionally seek
medical help. Liquid ejected from the
battery may cause irritation or burns.
6) SERVICE
a) Have your power tool serviced by
a qualified repair person using only
identical replacement parts. This will
ensure that the safety of the power tool is
maintained.
HEDGE TRIMMER SAFETY
WARNINGS
1. Keep all parts of the body away from
the cutter blade. Do not remove
cut material or hold material to
be cut when blades are moving.
Make sure the switch is off when
clearing jammed material. A moment
of inattention while operating the hedge
trimmer may result in serious personal
injury.
2. Carry the hedge trimmer by the
handle with the cutter blade stopped.
When transporting or storing the
hedge trimmer always fit the cutting
device cover. Proper handling of the
hedge trimmer will reduce possible
personal injury from the cutter blades.
3. Hold the power tool by insulated
gripping surfaces only, because the
cutter blade may contact hidden
3
Cordless Hedge Trimmer WG268E WG268E.9
Page 4
wiring. Cutter blades contacting a “live”
wire may make exposed metal parts of
the power tool “live” and could give the
operator an electric shock.
4. Check the hedge for foreign objects, e.g.
wire fences.
5. Use both hands when operating the hedge
trimmer. Using one hand could cause loss
of control and result in serious personal
injury.
SAFETY WARNINGS FOR
BATTERY PACK
a) Do not dismantle, open or shred cells
or battery pack.
b) Do not short-circuit a battery pack. Do
not store battery packs haphazardly
in a box or drawer where they may
short-circuit each other or be shortcircuited by conductive materials.
When battery pack is not in use, keep it
away from other metal objects, like paper
4
clips, coins, keys, nails, screws or other
small metal objects, that can make a
connection from one terminal to another.
Shorting the battery terminals together
may cause burns or a fire.
c) Do not expose battery pack to heat or
fire. Avoid storage in direct sunlight.
d) Do not subject battery pack to
mechanical shock.
e) In the event of battery leaking, do not
allow the liquid to come into contact
with the skin or eyes. If contact has
been made, wash the affected area
with copious amounts of water and
seek medical advice.
f) Seek medical advice immediately
if a cell or battery pack has been
swallowed.
g) Keep battery pack clean and dry.
h) Wipe the battery pack terminals with
a clean dry cloth if they become dirty.
i) Battery pack needs to be charged
before use. Always refer to this
instruction and use the correct
charging procedure.
j) Do not maintain battery pack on
charge when not in use.
k) After extended periods of storage,
it may be necessary to charge
and discharge the battery pack
several times to obtain maximum
performance.
l) Battery pack gives its best
performance when it is operated at
normal room temperature (20°C±5°C).
m) When disposing of battery packs,
keep battery packs of different
electrochemical systems separate
from each other.
n) Recharge only with the charger
specified by WORX. Do not use any
charger other than that specifically
provided for use with the equipment.
A charger that is suitable for one type of
battery pack may create a risk of fire when
used with another battery pack.
o) Do not use any battery pack which
is not designed for use with the
equipment.
p) Keep battery pack out of the reach of
children.
q) Retain the original product literature
for future reference.
r) Remove the battery from the
equipment when not in use.
s) Dispose of properly.
Cordless Hedge Trimmer WG268E WG268E.9
Page 5
SYMBOLS
To reduce the risk of injury, user
must read instruction manual
Wear ear protection
Wear eye protection
Wear dust mask
Do not expose to rain.
Do not expose to rain or water
Do not burn
5
Do not dispose of batteries. Return
exhausted batteries to your local
collection or recycling point.
Waste electrical products must not
be disposed of with household
waste. Please recycle where
facilities exist. Check with your local
authorities or retailer for recycling
advice.
xINR18/65-y: Cylindrical lithium Ion
battery cells with max diameter
of 18mm and max height of
65mm; “x” represents a number
cells serial connected, blank if 1;
“-y” represents a number of cells
paralleled connected, blank if 1
Cordless Hedge Trimmer WG268E WG268E.9
Page 6
8
7 6 5 4 3 2 1
9
6
1. REAR HANDLE
2. REAR SWITCH LEVER
3. BATTERY PACK
4. BATTERY PACK RELEASE BUTTON
5. FRONT SWITCH LEVER (ALL AROUND SWITCH FUNCTION)
6. FRONT HANDLE
7. SAFETY GUARD
8. BLADE
9. BLADE SHEATH*
* Not all the accessories illustrated or described are included in standard delivery.
Cordless Hedge Trimmer WG268E WG268E.9
Page 7
TECHNICAL DATA
Type
WG268E WG268E.9 (230-269-designation of machinery, representative of
cordless hedge trimmer)
WG268E WG268E.9
Voltage 40V Max*
No load speed 2300/min
Max.cutting length 56cm
Max.cutting diameter 27mm
Charging time 1hr. /
Machine weight 4.2kg 3.4kg
*Voltage measured without workload. Initial battery voltage reaches maximum of 40 volts.
Nominal voltage is 36 volts.
NOISE INFORMATION
A weighted sound pressure 80dB(A)
A weighted sound power 94dB(A)
K
3.0dB(A)
pA
Wear ear protection when sound pressure is over 80dB(A)
Typical weighted vibration ah<2.5m/s²
Uncertainty K=1.5m/s²
7
The declared vibration total value may be used for comparing one tool with another, and may
also be used in a preliminary assessment of exposure.
WARNING: The vibration emission value during actual use of the power tool can differ
from the declared value depending on the ways in which the tool is used dependant on the
following examples and other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles and if any anti vibration accessories are used.
And the tool is being used as intended by its design and these instructions.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed.
WARNING: To be accurate, an estimation of exposure level in the actual conditions of use
should also take account of all parts of the operating cycle such as the times when the tool
is switched off and when it is running idle but not actually doing the job. This may significantly
reduce the exposure level over the total working period.
Cordless Hedge Trimmer WG268E WG268E.9
Page 8
Helping to minimize your vibration exposure risk.
ALWAYS use sharp chisels, drills and blades.
Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate).
If the tool is to be used regularly then invest in anti vibration accessories.
Avoid using tools in temperatures of 100C or less.
Plan your work schedule to spread any high vibration tool use across a number of days.
ACCESSORIES
WG268E WG268E.9
Battery pack (WA3536) 1
Charger (WA3735) 1 /
Safety guard 1 1
Blade sheath 1 1
We recommend that you purchase your accessories from the same store that sold you the tool.
Refer to the accessory packaging for further details. Store personnel can assist you and offer
advice.
8
/
Cordless Hedge Trimmer WG268E WG268E.9
Page 9
OPERATING INSTRUCTIONS
F
E
G1
H
G2
K
I
J
WARNING! Do not use the product without
attaching the guard and front handle.
INTENDED USE
This machine is intended to be used domestically for
cutting and trimming hedges and bushes.
1. GUARD ASSEMBLY
Insert the Safety Guard (7) into the slot as illustrated in
Fig A; Use two screws to fix the guard securely.
NOTE: Make sure the Guard is firmly secured in place
2. FRONT HANDLE ASSEMBLY
The Front Handle (6) must be assembled before use:
1) Remove the bolt from the Front Handle.
2) Attach the Front Handle to the housing. Make
sure the protruding marks on the Front Handle
fit perfectly into the matching indentation on the
housing. (See Fig. B&C)
3) Insert the locking bolt into the handle and fully
tighten the bolt. (See Fig. D)
4) Check whether handle is firmly secured, if not
retighten the locking bolt.
NOTE: Make sure the handle is firmly secured in
place
3. BEFORE USING YOUR CORDLESS
HEDGETRIMMER
WARNING! The charger and battery pack are
specially designed to work together so do not
attempt to use any other devices. Never insert or allow
metallic objects into your charger or battery pack
connections because of an electrical failure and hazard
will occur.
NOTE: Your battery pack is UNCHARGED and you must
charge once before use.
The battery charger supplied is matched to the Li-Ion
battery installed in the machine. Do not use another
battery charger.
A
B
9
C
4. CHARGING YOUR BATTERY PACK
The Li-Ion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit.
In a warm environment or after heavy use, the battery
pack may become too hot to permit charging. Allow
time for the battery to cool down before recharging.
D
Cordless Hedge Trimmer WG268E WG268E.9
Page 10
10
H
K
I
J
5. TO REMOVE OR INSTALL BATTERY PACK (See
Fig. E)
Depress the Battery Pack Release Button (4) to remove
the Battery Pack (3) from your Hedge Trimmer. After
recharging, insert the Battery Pack into trimmer’s
battery port (See Fig. E). A simple push and slight
pressure will be sufficient until a click is heard. Check to
see if the battery is fully secured.
NOTE: When removing the battery pack, hold it
firmly to avoid dropping and injury.
E
F
6. BATTERY STATUS LED’S (See Fig. F )
NOTE: The Status LED’s will indicate the battery
condition when the button on the battery is
pressed.
The LED’s constantly senses and displays the battery
condition as follows:
Press the button “POWERTEST”, the light button is
illuminated.
When the three green lights are illuminated, the battery
is in a highly charged condition.
When two lights ( ) are illuminated, the battery is in
a moderately charged condition.
When only one green light ( ) is illuminated, the
battery charge is depleted.
IMPORTANT:
When only one light is illuminated, your battery
is overly discharged, even though the trimmer
may still be capable of trimming hedge.
Continuing to operate your trimmer with the
battery in this discharged condition may reduce
the life and performance of your battery.
7. STARTING AND STOPPING
BEFORE STARTING YOUR HEDGE TRIMMER
Remove Blade Sheath (9).
G1
G2
TO START YOUR HEDGE TRIMMER
Your Hedge Trimmer is equipped with both Rear and
Front Switch levers. Both switch levers need to be
depressed for the Hedge Trimmer to start. Depress
and hold the Front Switch Lever (5) and press the Rear
Switch Lever (2) (See Fig. G1).
TO STOP YOUR HEDGE TRIMMER
Move Hedge Trimmer away from cutting area before
stopping.
To stop, release one of the switch levers (See Fig. G2).
WARNING: If any parts are missing,
damaged or broken, do not operate your
hedge trimmer until all damaged parts have been
replaced or repaired. Failure to do so could result
Cordless Hedge Trimmer WG268E WG268E.9
Page 11
in serious personal injury. DO NOT USE WITHOUT
HANDLE AND GUARD
8. HOW TO USE YOUR HEDGE TRIMMER
Note that the Front Switch Lever (5) can be activated on
three sides, giving you many choices for a comfortable
grip. Before cutting an area, inspect it first and remove
any foreign objects that could become thrown or
entangled in the blades. Always hold the trimmer with
both hands and with the blade away from you before
turning it on.
When trimming new growth, use a wide sweeping
action so that the stems are fed directly into the blade.
(See Fig. H& I)
Allow the cutting blades to reach full speed before
cutting. When operating, keep the cutting blades away
from people and objects such as walls, large stones,
trees, vehicles, etc.
If the blade stalls, immediately stop the trimmer.
Release the two Switch Levers (5 & 2) before attempting
to clear jammed debris from the cutting blades.
Wear gloves when trimming thorny or prickly growth.
Do not attempt to cut stems that are too thick for the
cutting blade.
TOP CUTTING
Use a wide sweeping motion (See Fig. H). A slight
downward tilt of the cutting blades in the direction of
motion gives the best cutting results.
SIDE CUTTING
When trimming the sides of the hedge, begin at the
bottom and cut upwards (See Fig. I), tapering the hedge
inward at the top. This shape will expose more of the
hedge, resulting in a more uniformed growth.
H
I
11
9. CLEANING
REMOVE THE BATTERY PACK (3). Use a soft brush to
remove debris from all air intakes and cutting blade.
Wipe the surface with a dry cloth.
WARNING: Never use water for cleaning your
trimmer. Do not clean with chemicals, including
petrol, or solvents as this may damage your trimmer.
LUBRICATING THE CUTTING BLADE
For easier operation and longer life, lubricate the
cutting blades before and after each use. Before
lubricating, make sure the battery is removed from the
trimmer. Apply oil between the two blades periodically
(See Fig. J).
AT THE END OF THE CUTTING SEASON
Clean your trimmer thoroughly.
Check that all nuts and bolts are secure.
J
K
Cordless Hedge Trimmer WG268E WG268E.9
Page 12
Visually inspect the trimmer for any worn or
damaged parts.
TO STORE YOUR HEDGE TRIMMER
The trimmer blade cover/storage holder is
provided with 2 hanging slots for storing the
trimmer on the wall (See Fig. K) Ensure the
blade cover/storage holder is fitted before
storage.
Store in a dry place where your trimmer can
be protected from damage.
MAINTENANCE
Remove the battery from Hedge trimmer
before carrying out any adjustment,
servicing or maintenance.
Your power tool requires no additional
lubrication or maintenance.
There are no user serviceable parts in your
power tool. Never use water or chemical
cleaners to clean your power tool. Wipe clean
with a dry cloth. Always store your power tool
in a dry place. Keep the motor ventilation slots
clean. Keep all working controls free of dust.
12
ENVIRONMENTAL
PROTECTION
Waste electrical products must not be
disposed of with household waste.
Please recycle where facilities exist.
Check with your local authorities or retailer for
recycling advice.
DECLARATION OF
CONFORMITY
We,
Positec Power Tools (Europe) Ltd
PO Box 6242, Newbury, RG14 9LT, UK
Declare that the product,
Description WORX Cordless Hedge Trimmer
Type WG268E WG268E.9 (230-269-
designation of machinery, representative
of cordless hedge trimmer)
Function Trimming hedges and brushes
2006/42/EC, 2004/108/EC, 2011/65/EU,
2000/14/EC amended by 2005/88/EC
2000/14/EC amended by 2005/88/EC:
- Conformity Assessment Procedure as per
Annex V
- Measured Sound Power Level 91.9d B (A)
- Declared Guaranteed Sound Power Level
94dB(A)
Standards conform to,
EN 60745-1,
EN 60745-2-15,
EN ISO 3744,
EN 55014-1,
EN 55014-2
The person authorized to compile the
technical file,
Name Russell Nicholson
Address Positec Power Tools (Europe)
Ltd, PO Box 6242, Newbury, RG14 9LT,
UK
Suzhou 2016/06/24
Allen Ding
Deputy Chief Engineer,Testing & Certification
Cordless Hedge Trimmer WG268E WG268E.9
Page 13
Page 14
Page 15
Page 16
LITHIUM ION BATTERY
Handle With Care. Do Not Load or
Transport Package If Damaged.
A Fire Hazard Could Exist.
For more information, call: +86-512-65152811
Copyright © 2016, Positec. All Rights Reserved.
AR01250600
www.worx.com
Loading...