Workzone DBAF50/40 Instruction Manual

Xfinity Li-ION 20V cordless

BRAD NAILER / STAPLER

Instruction Manual

MODEL NUMBER DBAF50/40

*BATTERY

NOT INCLUDED

Version number: 12/2018

IMPORTANT:

Read carefully before use

Keep for future reference

YEAR WARRANTY

AUS

AFTER SALES SUPPORT

[e-mail]

1800 909 909

CONTENTS

• 1 x Brad Nailer/Stapler

• 1 x Belt Hook

• 200 x 32mm Staples

• 200 x 40mm Nails

• 1 x 3mm Hex Key

• 1 x Instruction Manual

• 1 x Warranty Card

MODEL: DBAF50/40 PRODUCT CODE: 61420 07/2018

AUS

Original Instructions

Year of manufacturing: 2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

2 3

Contents

Welcome 2
Contents 3
Application 4
Pack Content List 4
Parts Description 5
Description of symbols 6
General Power Tool Safety Warnings 7
Safety Rules for Nailers / Staplers 11
Important information – Product care 16
Assembly / Fitting and removing the Battery from the
Brad Nailer / Stapler and Charger 17
Belt Hook 18
Preparation - Loading Nails and Staples into the Brad Nailer / Stapler 19
A. Loading Staples 19
B. Loading Nails 20
Depth Adjustment Wheel 21
Operation - Checking the LED Battery and function indicator 22
Setting the Single or Contact Firing Function 23
A. Single Firing 23
B. Contact Firing 24
Using the LED Worklight/s while using the Brad Nailer / Stapler 24
Removing jammed Nails / Staples 25
Overload Protection 26
Maintenance - Magazine Maintenance 26
Cleaning 26
Transport 26
Battery Maintenance 26
Warranty 27
Environmental protection 27
What your 5 year warranty means 28
Service Support 28
Accessories & After Sales Parts 28
FAQ/Troubleshooting 29
Technical Specication 30
Warranty Details 32
Repair and Refurbished Goods or Parts Notice 33

Welcome

Congratulations in choosing to buy a Workzone® Titanium 20V Li-Ion
Cordless Brad Nailer / Stapler (Battery and Charger not included).

All products bought to you by Workzone® Titanium are
manufactured to the highest standards of performance and safety
and, as part of our philosophy of customer service and satisfaction,
are backed by our comprehensive 5 Year Warranty. We hope you will
enjoy your purchase for many years to come.

When you open your packaging, rst remove all items and check
there are no parts damaged or missing. If you nd anything wrong,
do not operate the product until the parts have been replaced or
the fault has been rectied. Failure to do so could result in serious
personal injury.

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

4 5

18

19

15

16

14

17

Pack contents / parts

BRAD NAILER / STAPLER 20V - DBAF50/40

1. Application

First time users or inexperienced operators pay particular attention to
the operation of the 20V Li-Ion Brad Nailer / Stapler, including details of
starting and stopping and correct use of the 20V Li-Ion Brad Nailer / Stapler
on pages 22-24, as well as the maintenance instructions on pages 26.

Intended use of the 20V Li-Ion Brad Nailer / Stapler
(battery / charger not included)

NOTE: This product is for private domestic DIY use only.

It is not suitable for commercial or trade use.
This 20V Brad Nailer / Stapler is used for such applications including:
Finishes and trims (Interior and exterior), Door and window casings and
trims, door jambs, ooring, baseboard paneling, & DIY cabinetry.
Use the tool only for intended applications.

3. Parts description

WARNING! To reduce risk of injury, only use Xfinity Plus battery

packs. Other type of battery packs may burst causing personal injury
and damag e. The battery pack must be recharged only with an
Xfinity Plus battery charger.

WARNING!

Please read and understand this instruction manual
before use and keep it for your future reference. Your power tool
should only be passed on together with this instruction manual.

2. Package Content List

1 x Brad Nailer / Stapler
1 x Belt Hook
200 x 32mm Staples
200 x 40mm Nails
1 x 3mm Hex Key
1 x Instruction Manual
1 x Warranty Card

• Remove all packing materials

• Ensure all parts on the contents list
are present

• Check the appliance, and all
accessories for transportation
damages

1. Safety striker pin

2. Workpiece contact (nail/staple release)

3. Depth adjustment wheel

4. Cylinder (internal)

5. Soft grip handle

6. Trigger switch

7. LED worklight switch

8. Belt hook

9. Single/contact ring slider knob

10. LED Battery and function indicator

11. Magazine

12. Indicator window

13. LED Worklight (both sides)

14. Magazine release latch

15. 200 x 32mm Staples

16. 200 x 40mm Nails

17. Battery

(not included; shown only
for illustrative and instructional
purposes only)

18. Charger

(not included; shown only
For illustrative and instructional
purposes only)

19. 3mm Hex Key

8

7

6

4

4

5

17

1

3

2

12

9

11

10

13

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

6 7

4. Description of symbols

The instruction manual, rating plate, or on the product itself, may show
these symbols. These represent important information about the product
or instructions on its use.

Caution/Warning:

Read all safety warnings and all instructions.

Regulatory Compliance Mark. Appliance complies with

requirements of electrical approval & EMC in Australia.

Waste electrical products should not

be disposed of with household waste.

Read the instruction manual.

Wear eye protection.
Wear ear protectors.
Exposure to noise can cause hearing loss.

60 Month Warranty Period.

SINGLE FIRING: Push the single / contact ring switch to the LEFT side
CONTACT FIRING: Push the single / contact ring switch to the RIGHT side

LED Red Flashing = Jam
LED Red = Low battery
LED Green Flashing = Overheat
LED Green = NO nails / staples

Decrease depth

Increase depth

5. General Power Tool Safety Warnings

WARNING. Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.

Save all warnings and instructions for future reference.

The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered and dark areas invite

accidents.

b. Do not operate power tools in explosive atmospheres, such as in the

presence of ammable liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodied plugs and matching outlets will reduce risk of electric

shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes,

radiators, ranges and refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a

power tool will increase the risk of electric shock.

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

8 9

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired
or under the inuence of drugs, alcohol or medication. A moment of

inattention while operating power tools may result in serious personal
injury.

b. Use personal protective equipment. Always wear eye protection.

Protective equipment such as dust masks, non-skid safety shoes, hard hat,
or hearing protection used for appropriate conditions will reduce the risk
of personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the o position

before connecting to power source and/or battery pack, picking up
or carrying the tool. Carrying power tools with your nger on the switch

or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool

on. A wrench or a key left attached to a rotating part of the power tool

may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This

enables better control of the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your

hair, clothing and gloves away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and

collection facilities, ensure these are connected and properly used.

Use of these devices can reduce dust related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the

rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and o. Any

power tool that cannot be controlled with the switch is dangerous and
must be repaired.

c. Disconnect the plug from the power source and/or the battery pack

from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow

persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of

untrained users.

e. Maintain power tools. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may aect the
power tool’s operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained power tools.

f. Use the power tool, accessories and tool bits etc. in accordance with

these instructions, taking into account the working conditions and
the work to be performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

5. Battery tool use and care

a) Recharge only with the charger specied by the manufacturer. A

charger that is suitable for one type of battery pack may create a risk of
re when used with another battery pack.

b) Use power tools only with specically designated battery packs.

Use of any other battery packs may create a risk of injury and re.

c) When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws or other small metal
objects, that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns
or a re.

d) Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, ush with water. If liquid
contacts eyes, additionally seek medical help. Liquid ejected from the

battery may cause irritation or burns.

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

10 11

6. Service
a. Have your power tool serviced by a qualied repair person

using only identical replacement parts. This will ensure that the

safety of the power tool is maintained.

7. Safety notes for battery/charger.

a. Keep the charger away from rain or damp conditions. Water entering

into the charger will increase the risk of an electrical shock.

b. Only use chargers recommended by the manufacturer to recharge

the battery. There is a risk of re if it is used with other batteries.

c. Never use to recharge third-party batteries. The charger is only

designed to charge the supplied batteries (Li-Ion) using the voltages
specied in the Technical Data. Otherwise there is a risk of re or
explosion.

d. Keep the charger clean. Contamination will increase the risk of an

electrical shock.

e. Check the charger, cable and plug each time you use the unit. Do

not use the charger if you nd any damage. Never open the charger up
yourself, have it repaired by a qualied specialist only and with original
replacement parts.
A damaged charger, cable or plug will increase the risk of an electrical
shock.

f. Never operate the charger on a surface that will burn easily (for

example, paper, textiles etc) or in a ammable environment. There is a

risk of re occurring as a result of the heat generated during the charging
process.

g. Fluid can escape from the battery when used incorrectly. Avoid all

contact with this. In the event of accidental contact, rinse with water. If
liquid should get into the eyes, get medical assistance. Battery uid may
result in skin irritations and burns.

h. Do not open the battery. There is a risk of short-circuiting.
i. Protect the battery from heat, for example, from constant sun and

re. There is a risk of explosion.

j. Never short circuit the battery. There is a risk of explosion.

k. In the event of damage and incorrect use, vapours may come out of

the battery. Ensure your work space is well ventilated with fresh air and, if

you have any symptoms, consult a doctor. These vapours may irritate the
respiratory system.

Safety Rules for Nailers / Staplers

• Always assume that the tool contains nails or staples. Careless handling of
the nailer can result in unexpected ring of nails or staples and personal
injury.

• Do not point the tool towards yourself or anyone nearby. Unexpected
triggering will discharge the nail or staple causing an injury.

• Do not actuate the tool unless the tool is placed rmly against the
workpiece. If the tool is not in contact with the workpiece, the nail or staple
may be deected away from your target.

• Disconnect the tool from the power source when the fastener jams in the
tool. While removing a jammed fastener, the tacker may be accidentally
activated if it is plugged in.

• Use caution while removing a jammed nail or staple. The mechanism may
be under compression and the nail or staple may be forcefully discharged
while attempting to free a jammed condition.

• Do not use this nailer for fastening electrical cables. It is not designed for
electric cable installation and may damage the insulation of electric cables
thereby causing electric shock or re hazards.

• Hold power tool by insulated gripping surfaces, when performing an
operation where the nail or staple may contact hidden wiring. Nails or
staples contacting a “live” wire may make exposed metal parts of the
power tool “live” and could give the operator an electric shock.

• Know your power tool. Read operator’s manual carefully. Learn its
applications and limitations, as well as the specic potential hazards
related to this power tool. Following this rule will reduce the risk of electric
shock, re, or serious injury.

• Always wear eye protection with side shields marked to comply with ANSI
Z87.1. Everyday glasses have only impact resistant lenses. They are not
safety glasses. Following this rule will reduce the risk of serious personal
injury.

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

12 13

• Eye protection which conforms to ANSI specications and provides
protection against ying particles both from the front and side should
always be worn by the operator and others in the work area when loading,
operating or servicing this tool. Eye protection is required to guard against
ying fasteners and debris, which could cause severe eye injury.

• The user must ensure that proper eye protection is worn. We recommend
Wide Vision Safety Mask for use over eyeglasses or standard safety glasses
that provide protection against ying particles both from the front and
side. Always use eye protection which is marked to comply with ANSI
Z87.1.

• Additional safety protection will be required in some environments. For
example, the working area may include exposure to noise level which can
lead to hearing damage. The user must ensure that any necessary hearing
protection is used by the operator and others in the work area. Some
environments will require the use of head protection equipment.

• Keep ngers away from trigger when not driving fasteners to avoid
accidental ring.

• Use safety equipment. Always wear eye protection. Dust mask, nonskid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.

• Protect your lungs. Wear a face or dust mask if the operation is dusty.
Following this rule will reduce the risk of serious personal injury.

• Protect your hearing. Wear hearing protection during extended periods of
operation. Following this rule will reduce the risk of serious personal injury.

• Battery tools do not have to be plugged into an electrical outlet; therefore,
they are always in operating condition. Be aware of possible hazards when
not using your battery tool or when changing accessories. Following this
rule will reduce the risk of electric shock, re, or serious personal injury.

• Do not place battery tools or their batteries near re or heat. This will
reduce the risk of explosion and injury.

• Use the tool only for its intended use. Do not discharge fasteners into
open air.

• Use the tool only for the purpose for which it was designed.

• Use only the nails or staples recommended for this tool. Use of the wrong
nails or staples could result in poor nail or staple feeding, jammed nails

or staples, and nails or staples leaving the tool at erratic angles. If nails
or staples are not feeding smoothly and properly, discontinue their use
immediately. Jammed and improperly feeding nails or staples could result
in serious personal injury.

• Never use this tool in a manner that could cause a nails or staples to be
directed toward anything other than the workpiece.

• Do not use the tool as a hammer.

• Always carry the tool by the handle.

• Do not alter or modify this tool from the original design or function
without approval from the manufacturer.

• Always be aware that misuse and improper handling of this tool can cause
injury to yourself and others.

• Never clamp or tape the trigger or workpiece contact in an actuated
position.

• Never leave tool unattended if the battery is installed.

• Do not operate this tool if it does not contain a legible warning label.

• Keep the tool and its handle dry, clean and free from oil and grease.
Always use a clean cloth when cleaning. Never use brake uids, gasoline,
petroleum-based products, or any strong solvents to clean your tool.
Following this rule will reduce the risk of loss of control and deterioration
of the enclosure plastic.

OPERATION

• Do not use tool if trigger does not actuate properly. Any tool that cannot
be controlled with the trigger is dangerous and must be repaired.

• Check operation of the workpiece contact mechanism frequently. Do not
use the tool if the workpiece contact mechanism is not working correctly
as accidental driving of a nail or staple may result. Do not interfere with the
proper operation of the workpiece contact mechanism.

• Do not use a tool that does not work correctly.

• Always assume that the tool contains nails/ staples.

• Do not carry the tool from place to place holding the trigger. Accidental
discharge could result.

• Always handle the tool with care:

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

14 15

- Respect the tool as a working implement.

- Never engage in horseplay.

- Never pull the trigger unless nose is directed toward the work.

- Keep others a safe distance from the tool while tool is in operation as
accidental actuation may occur, possibly causing injury.

• The tool is designed for single-hand use. Do not hold the tool by the front

of the magazine. Do not put hands, head, or other parts of your body
near the bottom of the magazine where the nail or staple exits the tool, as
serious personal injury could be caused.

• Do not point the tool toward yourself or anyone whether it contains nails or

staples or not.

• Do not actuate the tool unless you intend to drive a nail or staple into the

workpiece.

• Always ensure that the workpiece contact is fully positioned above the

workpiece. Positioning the workpiece contact only partially above the
workpiece could cause the nail or staple to miss the workpiece completely
and result in serious personal injury.

• Do not drive nails or staples near edge of material. The workpiece may

split causing the nail or staple to ricochet, injuring you or others. Be aware
that the nail may follow the grain of the wood, causing it to protrude
unexpectedly from the side of the work material or deect, possibly
causing injury.

• Keep hands and body parts clear of immediate work area. Hold workpiece

with clamps when necessary to keep hands and body out of potential
harm. Be sure the workpiece is properly secured before pressing the
fastener against the material. The workpiece contact may cause the work
material to shift unexpectedly.

• Keep face and body parts away from back of the tool cap when working in

restricted areas. Sudden recoil can result in impact to the body, especially
when nailing into hard or dense material.

• During normal use the tool will recoil immediately after driving a fastener.

This is a normal function of the tool. Do not attempt to prevent the recoil
by holding the tool against the work. Restriction to the recoil can result
in a second fastener being driven from the tool. Grip the handle rmly,

let the tool do the work and do not place second hand on top of tool or
near exhaust at any time. Failure to heed this warning can result in serious
personal injury.

• Do not drive fasteners on top of other fasteners or with the tool at an
overly steep angle as this may cause deection of fasteners which could
cause injury.

LOADING TOOL

• Do not load the tool with fasteners when any one of the operating controls
is activated.

When loading tool:

• Never place a hand or any part of body in fastener discharge area of tool.

• Never point tool at anyone.

• Do not pull the trigger or depress the workpiece contact as accidental
actuation may occur, possibly causing injury.

SAVE THESE INSTRUCTIONS

• Refer to them frequently and use them to instruct others who

may use this tool. If you loan someone this tool, loan them these
instructions also.

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

16 17

Important information – Product care

NOTE: Xnity Battery and Charger not included. For any issues related
directly to your purchased ALDI Xnity Battery / charger, contact the
Customer Service of the manufacturer as listed on the battery / charger
packaging, manual or on the label on the battery / charger.

This Brad Nailer / Stapler uses Lithium Ion Battery Cells. Care MUST be taken to
ensure both the safety and life of the pack is maintained. Ensure you have read all
of the safety notes in the previous pages before using the Brad Nailer / Stapler.

Treat the battery pack with care and within the guidelines of this manual and the
supplied manual included with the purchase of ALDI Xnity Battery/s.

If the battery pack does become immersed in water or any uids, or is subject
to a severe drop or it does not operate within the guidelines of this manual
or the supplied manual included with the purchase of ALDI Xnity Battery/s,
immediately STOP using the battery pack and have it checked. During operation
avoid overloading the Brad Nailer / Stapler. If the Brad Nailer / Stapler is
overloaded it will automatically STOP. Overloading may occur for a number of
reasons including when the Brad Nailer / Stapler is pushed too hard or when
using a Nail / Staple greater than what is specied, or there is a nail / staple jam. If
you do overload the Brad Nailer / Stapler during operation refer to the “Overload
Protection” section in this manual.

NOTE: When the battery of the Brad Nailer / Stapler is at the lower end of the
charge, the Brad Nailer / Stapler is more susceptible to the overload condition.
Running the Brad Nailer / Stapler at close to maximum load, or continual resetting
of the overload will cause the battery pack to overheat. When a preset cell
temperature is detected, the battery pack will automatically STOP operating and
will not restart until the battery pack has cooled to a safe level.

In this condition, DO NOT force the cooling down of the pack by placing in a
freezer or similar device. Refer to the “Overload Protection” section in this manual.

Another feature of the Brad Nailer / Stapler is the low voltage cut out feature. This
feature operates when the voltage drops below a preset value. When this occurs
the tool will automatically stop operating. To correct the situation you need to
either insert another charged battery into the Brad Nailer / Stapler or recharge the
existing battery, and then proceed with the Brad Nailer / Stapler application.

NOTE: Attempting to restart the tool in this condition without either recharging
the battery or installing a battery with charge will lead to Brad Nailer / Stapler
restarting and then stopping again after only a few seconds of operation.

These safety devices have been tted for the safety, reliability and life of the tool.

Assembly

Fitting and removing the Battery from the Brad Nailer /
Stapler and Charger.

NOTE: (Xnity Battery pack and charger is not included with
this product; it is shown only for illustrative and instructional
purposes only)

1. To install your purchased Xnity battery (17) on to the Brad Nailer /
Stapler, align the grooved guide rails of the battery (17) with the raised
guide rails on the bottom of the Brad Nailer / Stapler. With your thumb
on the battery release tab on the battery pack, slide it rmly into the
handle until the battery is secure in position (Fig A). Release your thumb
from the battery release tab. When the battery is secured you will hear it
engage with a snap / click.

2. To remove the battery (17) from the Brad Nailer / Stapler, press the

battery pack release button and slide the battery (17) completely out
and away from the Brad Nailer / Stapler (Fig B).

3. When applying the battery (17) onto your purchased Xnity charger

(18), align the grooved guide rails of the battery (17) with the raised
guide rails on the charger (18) (Fig C). The charger (18) will make a snap
/ click noise when it is securely aligned.

A. B.

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

18 19

4. To remove the battery (17) from the charger
(18), press the battery release button on the
battery (17) and slide away from the charger
in the reverse direction it was installed into
the charger (18) (Fig C).

NOTE: For any issues related directly to

your purchased ALDI Xnity Battery /
charger, contact the Customer Service of
the manufacturer as listed on the battery /
charger packaging, manual or on the label
on the battery / charger.

Belt Hook

Your Brad Nailer / Stapler comes with a belt hook
which is already assembled onto the product.
No assembly is required (Fig D).

D.

Preparation

Loading Nails and Staples into the Brad Nailer / Stapler

WARNING: Keep the tool pointed away from yourself and others

when loading nails or staples. Failure to do so could result in
possible serious personal injury.

WARNING: Ensure to remove battery pack from the tool during
nail / staple loading.

NOTE: If the staple or nail cartridge is not loaded correctly, the magazine
will not secure, and the magazine release latch (14) will not re-engage.

WARNING: Do not install nails and staples together.

A. Loading Staples

NOTE: Do not install staples of dierent sizes at the same time. Only

1 x cartridge of the same size staples should be installed at each use.
Loading various staple sizes at one time will cause malfunction and
void your warranty.

1. Press on the magazine release latch (14), to open the magazine (11)
(Fig E), ensuring you extend it out as far as it will release (Fig F).

2. To load staples, insert the cartridge of staples with the crown of the
staples to the top rear of the open magazine with the staple feet
facing away (Fig G).

C.

INSTALL

REMOVE

E. F. G.

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

20 21

Ensure the end of the staple cartridge engages inside the guide rails at

the end of the magazine (Fig H).

3. Push the magazine (11) closed by pushing it up towards the safety
striker pin (1) end of the magazine until it closes securely (Fig I). The
magazine release latch (14) will engage and a “click” will be heard when
secure (Fig J).

B. Loading Nails

NOTE: Do not install nails of dierent sizes at the same time. Only 1 x

cartridge of the same size nail should be installed at each use. Loading
various nail sizes at one time will cause malfunction and void your warranty.

1. Press on the magazine release latch (14), to open the magazine (11)
(Fig E), ensuring you extend it out as far as it will release (Fig F).

2. To load nails, insert the cartridge of nails with the heads of the nails
facing to the top rear of the open magazine with the nail points facing
away (Fig K). Ensure the end of the nail cartridge engages inside the
guide rails at the end of the magazine (Fig H).

3. Push the magazine (11) closed by pushing it up towards the safety striker
pin (1) end of the magazine until it closes securely (Fig I). The magazine
release latch (14) will engage and a “click” will be heard when secure
(Fig J).

Depth Adjustment Wheel

WARNING: Keep the tool pointed away from yourself and others

when setting the depth adjustment. Failure to do so could result in
possible serious personal injury.

WARNING: Ensure to remove battery pack from the tool during
initial depth adjustment setting.

The depth adjustment wheel (3) (Fig L) is used for setting the depth of the
nail or the staple from the workpiece contact (nail/staple release) (2).
On each side of the depth adjustment wheel (3) is a symbol indicating
whether turning the wheel in that direction will increase or decrease the
nail / staple depth (Fig M). The range of the depth adjustment wheel (3)
is approx. 3mm.

1. When viewing the depth adjustment wheel (3) per Fig M, turning the
depth adjustment wheel (3) to the left will increase the depth of the nail
/ staple into the contact surface. If pushing all the way to the left, the nail
will be ush on the contact surface.

2. Turning the depth adjustment wheel (3) to the right will decrease the
depth of the nail / staple into the contact surface.

3. It is recommended to test the depth of adjustment doing a few test
shots, and then adjusting the wheel accordingly to reach the desired
depth required for the contact surface. Proceed to the next page for
Operation to start your product and check the adjustment.

H. I. J.

K. L. M.

“CLICK”

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

22 23

Operation

Checking the LED Battery and
function indicator

WARNING: Always keep the tool pointed

away from yourself and others when in
use. Failure to do so could result in possible
serious personal injury.

1. After installing the nail / staple cartridge into
the magazine, install your purchased fully
charged Xnity battery onto the brad nailer/
stapler per instructions on pages 19/20.

2. Check there are no lights lit up on the LED
battery and function indicator (10). If you have
loaded the nails or staples correctly, and the
battery is fully charged, no lights will be on.

3. If the LED battery and function indicator (10) is
ashing red this indicates there is a jam in the
magazine (Fig N). Refer to page 25 for xing
jams.

4. If the LED battery and function indicator (10) is
red, this indicates the battery is low on charge
(Fig O). Charge your purchased Xnity battery.

5. If the LED battery and function indicator (10)
is ashing green (Fig P), this indicates the brad
nailer / stapler has overheated. Refer to page
26 for further instruction.

6. If the LED Battery and function indicator (10)
is green (Fig Q), there are no nails/ staples
installed. Refer to pages 19/20 for installing
nails / staples.

Setting the Single or Contact Firing
Function

1. To set the ring function to single shots, slide
the single/contact ring slider knob (9) to the
left (Fig R). Single ring is suitable for precise
single nail / staple placement.

2. To set the ring function to multiple contact
shots, slide the single/contact ring slider
knob (9) to the right (Fig S). Continual contact
ring is good for quick and multiple nail /
staple ring.

A. Single Firing

1. Once the single/contact ring slider knob (9)
is set to single ring, depress the safety striker
pin ush on the contact surface (Fig T), and
then press the trigger switch (6) to re a single
nail or staple (Fig U).

2. Release the trigger switch (6), and lift the brad
nailer / stapler away from the contact surface,
hence also releasing the safety striker pin (1).

3. Repeat the process for single ring of
individual nails or staples.

NOTE: The safety striker pin (1) MUST be

depressed at the same time as pressing the
trigger switch (6), otherwise the Brad nailer /
stapler will not re / function.

Q. U.

P.

T.

O.

S.

N.

R.

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

24 25

B. Contact Firing

1. Once the single/contact ring slider knob (9) is set to contact ring,
depress the trigger switch (6) (Fig U), and then depress the safety striker
pin ush on the contact surface to re a single nail / staple (Fig T).

2. Keeping your nger pressed on the trigger switch (6), lift the Brad
nailer / stapler away from the contact surface, hence also releasing the
safety striker pin (1), and place in the next position for the next nail or
staple to be red, again depressing the safety striker pin ush onto the
contact surface. The Brad nailer / stapler will automatically re another
staple or nail again (Fig V).

3. Repeat the process keeping your nger pressed on the trigger switch
(6), to continually re each nail/staple.

NOTE: The safety striker pin (1) MUST be depressed at the same time as

continually pressing the trigger switch (6), otherwise the Brad nailer /
stapler will not re / function.

WARNING: Do not keep the trigger switch (6) depressed when

the tool is not in use to prevent accidental ring.

Using the LED Worklight/s while using the

Brad Nailer / Stapler

CAUTION! LED is laser class 1! Do not look directly into the laser as this

may result in damage to the eyes.

1. To turn on the LED worklights while on the Brad nailer / stapler, press
on the LED worklight switch (7) before pressing on the trigger switch
(6) (Fig W/X).

Removing jammed Nails / Staples

1. If the LED battery and function indicator (10) is ashing red (Fig N)
this indicates a jam in the magazine.

2. Remove the battery from the Brad nailer / stapler.

3. Open the magazine by pressing on the magazine release latch (14)
(Fig Y), and remove the nail or staple cartridge and the jammed nail or
staple (Fig Z).

4. Re-install nails or staples, re-install battery, and check the jam is
corrected. If corrected, the red light will be no longer ashing on the
LED battery and function indicator (10).

5. If the jam is still not corrected it means a nail or staple may be jammed
in the internal striking mechanism.

6. Remove the battery from the Brad nailer / stapler, then using the
supplied 3mm hex key (19), remove the 4 x hex screws located in front
of the depth adjustment wheel and remove the nosepiece. Remove the
jammed nail / staple; this may require using pliers (Fig AA).

7. When the jam is removed, reattach the nose
piece and resecure the 4 x hex screws using
the supplied 3mm hex key (19). Re-install nails
or staples, re-install battery, and check the jam
is corrected. If corrected, the red light will be
no longer ashing on the LED battery and
function indicator (10).

V. W. X.

Y.

Z. AA.

JAM

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

26 27

CAUTION! Electrical and battery operated units that no longer work
should not be disposed of in the household waste! They are to be collected
separately, in accordance with your local waste disposal regulations.

ATTENTION! Batteries must be removed from battery powered tools
and disposed of separately in accordance with relevant waste battery
regulations.

Batteries must never be disposed of with domestic waste!

Please discard power tools no longer usable at a local collection point.
Collection and disposal of packaging materials separately by types

complying with local rules and regulations. For details, please contact your
local council.

Warranty

Your new WORKZONE® TITANIUM 20V Lithium-Ion Brad Nailer / Stapler will
more than satisfy your expectations.

It has been manufactured under stringent WORKZONE® TITANIUM Quality
Standards to meet superior performance criteria.

You will nd your new 20V Lithium-Ion Brad Nailer / Stapler easy and
safe to operate, and, with proper care, it will give you many years of
dependable service.

CAUTION. Carefully read through this entire instruction manual before
using your new WORKZONE® TITANIUM 20V Lithium-Ion Brad Nailer /
Stapler.

Take special care to heed the Cautions and Warnings.
Your WORKZONE® TITANIUM 20V Lithium-Ion Brad Nailer / Stapler

has many features that will make your job faster and easier. Safety,
performance, and dependability have been given top priority in the
development of this 20V Lithium-Ion Brad Nailer / Stapler, making it easy
to maintain and operate.

Use only WORKZONE® TITANIUM replacement parts for your product.
Non-conforming parts or modications made to parts will void your

warranty.

Environmental protection

Recycle unwanted materials instead of disposing of them as waste.
All tools, hoses and packaging should be sorted, taken to the local
recycling centre and disposed of in an environmentally safe way.

Overload Protection

If the LED battery and function indicator (10) is ashing green, the Brad nailer
/ stapler has overloaded / overheated possibly from extended use. Remove
the battery immediately and allow the unit to sit for 30 minutes – 1 hour.
When the Brad nailer / stapler has cooled, re-install the battery and check the
LED battery and function indicator (10) is no longer ashing green. If it is no
longer showing green, continue to use the Brad nailer / stapler.

If the Brad nailer / stapler continues to result in an overload / overheated
condition, DO NOT continue to use and make contact with customer service
by calling 1800 909 909 or emailing [e-mail] for
service advice.

Maintenance

Magazine Maintenance

WARNING: Ensure to remove battery pack from the tool during
cleaning and maintenance.

Ensure that no debris or dust enter the open magazine as this may cause
jamming or malfunction. Clean the inside of the magazine with a ne brush
or clean cloth. An air sprayer may also assist with removing any accumulated
dust or debris.

Cleaning

Avoid using solvents when cleaning plastic parts. Most plastics are
susceptible to damage from various types of commercial solvents and may
be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

Transport

When transporting the nailer / stapler, it is recommended to remove the
battery from the unit, remove any nails or staple cartridges in the unit to
avoid any potential misring, and store in a secure case or the packaging box
during transport.

Battery Maintenance

To maintain battery capacity, always refer to the specic instructions in the
supplied manual included with the purchase of ALDI Xnity Batteries. It is
recommended to recharge your battery every two months. Store only fully
charged batteries. They should therefore be recharged from time to time. The
place of storage must be dry.

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

28 29

Problem

Possible Cause Solution

Safety Striker Pin (1)
does not depress
fully and unit not
operating.

Low on staples or nails.
Safety Striker Pin (1) is jammed.

Re-install nails / staples into magazine.
Remove battery and clean any debris from

the magazine or around the safety striker
pin (1).

Brad nailer / stapler
operates properly
but nails / staples
not firing in full
depth.

Nail / staple is too long for the
contact surface.

Depth adjustment wheel (3) not
set properly

Use appropriate size nail / staples.
Adjust the depth adjustment wheel (3)

to an increased driving depth.

Brad nailer / stapler
operates properly
but nails / staples
ring too deep.

Depth adjustment wheel (3) not
set properly.

Adjust the depth adjustment wheel (3)
to an decreased driving depth.

Brad nailer / stapler
jams frequently.

Nails / staples are incorrect size.
Nails / staples are damaged.
Magazine is loose or dirty.

Check nail / staple size.
Replace the nail/s / staple/s.
Secure magazine.

Brad nailer / stapler
stops and LED light
is ashing red

Nail / staple is jammed. Clean magazine.

Refer to page 25 for xing jams.

Brad nailer / stapler
stops and LED
light is red (but not
ashing).

Battery low on charge. Charge battery.

Brad nailer / stapler
stops and LED light
is ashing green.

Brad nailer / stapler has over

-

heated / overloaded.

Refer to page 26 for treating overload
condition.

Brad nailer / stapler
stops and LED light
is green (but not
ashing)

No nails / staples loaded. Install nails / staples

What your 5 year warranty means

Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly.

In the event of product failure within its intended use over the course of
the rst 5 years after the date of purchase, we will remedy the problem
as quickly as possible once it has been brought to our attention. In the
unlikely event of such an occurrence, or if you require any information
about the product please contact us via our after sales support services,
details of which can be found in this manual and on the product itself.

After Sales Support TEL: [phone]

Service Support

If you have any issues with the operation of your product, please call us on
1800 909 909 for advice, or email us at [e-mail]

Accessories and After Sales Parts

The following is available for purchase by visiting https://help.tools/ or
calling our customer service hotline on: 1800 909 909

Replacement nails and staples for use with the Brad Nailer / Stapler
can be purchased at most local hardware stores under various dierent
brands. Ensure the specication of the Nails / Staple does not exceed
the maximum capacity of this product (Max nail length / type: 50mm,
18 gauge brad nail and Max staple length / type: 40mm, 18 gauge light
duty staple).

FAQ/Troubleshooting

* Battery and Charger not included with this product

For further inquiries or issues associated with your Brad Nailer / Stapler, call our

Customer Service on 1800 909 909 or email us at [e-mail]

1. Various staple size cartridges 2. Various nail size cartridges

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

30 31

Technical Specications

Voltage: 20V d.c.

Firing speed: 60 nails/staples per minute

Magazine capacity: 100 (nails or staples)

Led worklight: Yes

Max nail length / type: 50mm, 18 gauge brad nail

Max staple length / type: 40mm, 18 gauge light duty staple

Depth Adjustment wheel range: 0-3mm

Not included: Battery and charger

Weight: 2.65kg

Product Dimensions
(without battery) (L x W x H) cm : 26.7 x 25.2 x 9.6cm

This 20V Li-Ion Brad Nailer / Stapler complies with the following Standards:

Safety: EN 60745-1:2009/A11:2010

EN 60745-2-16:2010
AfPS GS 2014:01 PAK
AS/NZS 60745.1:2009
AS/NZS 60745.2.16:2009

EMC: EN 55014-1:2006/A2:2011

EN 55014-2:1997/A2:2008

BATTERY POWERS OVER

15 TOOLS

The Xnity battery System has more than 20 tools that work
with the same battery platform, giving you the ultimate
versatility in tool selection to get your job nished.

With LITHIUM powered batteries, you can get more done in
less time and improve the performance of every Xnity
powered Workzone® or Gardenline®
tool ever made.

Watch out for more
Xnity tools coming soon.

X

PLUSPLUS

20V

BATTERY SYSTEM

X

FINITY

20V

BATTERY SYSTEM

P LUSP LUS

BATTERY POWERS OVER

15 TOOLS

ONE

ONE

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

AFTER SALES SUPPORT

e-mail: [e-mail]

1800 909 909 (toll free)

MODEL No.: DBAF50/40 • 61420 • 07/2018

32 33

The product is guaranteed to be free from defects in workmanship and parts for a period of 60 months from the

REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

date of purchase. Defects that occur within this warranty period, under normal use and care, will be repaired,
replaced or refunded at our discretion. T

conferred by this warranty are in addition to all rights and
remedies in respect of the product that the consumer has under the Competition and Consumer Act 2010 and
similar state and territory laws.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.

Warranty Details

Unfortunately, from time to time, fault y products are manufactured w hich need to be returned to the Supplier
for repair.
Please be aware that if your product is c apable of retaining user-generated data (such as les store d on a computer
hard drive, telephone numbers store d on a mobile telephone, songs stored on a portable media p layer,
games saved on a games console or les store d on a USB memory stick) during the process of repair,
some or all of your stored data may be lost.

We recommend you save this data e

lsewhere prior to se nding the product for repa ir.

You should also be aware that rather than repairing goods, we may replace them wi th refurbished goods of
the same type or use ref urbished parts in the repair process .

Please be assured tho ugh, refurbished part s or replacements are only used w here they meet

If at any time you feel your repair is being handled uns atisfactorily, you may escalate your complaint.
Please call us on 1800 909 909, or email us at [e-mail]

Toolklub Pty. Ltd, 8 Ashenden Street, Leongatha, VIC, 3953
Toolklub Help Desk 1800 909 909 (Operating Hours: Mon-Fri 08:30AM to 06:00PM EST)
EMAIL: [e-mail]
INTERNET: https://help.tools/

Repair and Refurbished Goods

or Parts Notice

Brad Nailer / Stapler 20V Brad Nailer / Stapler 20V

YEAR WARRANTY

AUS

AFTER SALES SUPPORT

[e-mail]

1800 909 909

MODEL: DBAF50/40 PRODUCT CODE: 61420 07/2018

CONTENTS

1 x Brad Nailer / Stapler
1 x Belt Hook
200 x 32mm Staples
200 x 40mm Nails
1 x 3mm Hex Key
1 x Instruction Manual
1 x Warranty Card

ALDI guarantees that our exclusive brand products are developed

to our stringent quality specications. If you are not entirely

satised with this product, please return it to your nearest ALDI

store within 60 days from the date of purchase for a full refund

or replacement, or take advantage of our after sales support by

calling the supplier‘s Customer Service Hotline.

WORKZONE® TITANIUM is a registered trademark of ALDI Stores

Made in China

WORKZONE® TITANIUM is a registered trademark of ALDI Stores

DISTRIBUTED BY:

ALDI STORES

1 SARGENTS ROAD, MINCHINBURY NSW 2770

www.aldi.com.au