User Manual
Product
Info
51887
24V LITHIUM-ION
CORDLESS DRILL
WITH HAMMER
ACTION
www.powertoolsupport.com
Read all safety warnings and all instructions
thoroughly before operating this product.
IM ed5; 06/2016
QR codes take you where you want to go
Product
Info
quicky and easily
Whether you require product information, spare parts or accessories,
details on warranties or aftersales service, or if you want to watch
a product demonstration video, our QR codes will take you there in
no time at all.
What is a QR code?
A QR-code (QR=Quick Response) is a type of matrix that can be read
with a smartphone camera and that contains a link to a website or
contact details, for example.
Advantage: You are not required to manually enter a website address
or contact details.
How it works
To scan the QR code, all you need is a smartphone with QR codes reader
software and an Internet connection*. This type of software can be
downloaded for free from your smartphone’s app store.
Try it out now
Just scan the QR code with your smartphone and
find out more about the Aldi product you have
purchased*.
* Depending on your tariff you may be charged for the connection.
For Know How Videos, click on the
“Product Assistance” tab, then the
“How To Product Videos” link.
Contents
Pack contents / parts 2
Description of symbols 3
General safety warning 4
Additional Safety rules for chargers and batteries 10
Parts List 11
Important information – Product care 13
Fitting and removing the battery pack 14
Battery charging 14
2 Speed Gearbox 15
Using the Drill/driver 16
Drill/driver overload 16
Temperature cut out 17
Low voltage cut out 17
Forward/reverse switch 18
Adjustable torque 18
Using the Hammer function 18
Inserting and removing bits 19
Drill/driving 19
Drill/driving plastics and plastic coated chipboard 20
Drill/driving wood 20
All drill/driving operations 20
LED Work Light 20
Chuck replacement 20
Belt clip 21
Cleaning 21
Maintenance 21
Warranty 22
Service Support 22
Accessories 22
Environmental protection 23
What your 3 year warranty means 23
FAQ/Troubleshooting 24
Specications 25
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 51887 • 06/2016 • 51887
(toll free)
Pack contents / parts
Congratulations on the purchase of your Workzone® Titanium 24V
Lithium-Ion Cordless Drill. When you open your packaging, first remove
all items and check there are no parts damaged or missing. If you find
anything wrong, do not operate the product until the parts have been
replaced or the fault has been rectified. Failure to do so could result in
serious personal injury.
NOTE: First time users or inexperienced operators pay particular attention
to the operation of the Cordless Hammer Drill, including details of starting
and stopping and correct use of the Cordless Hammer Drill on pages 16 to
20, as well as the maintenance instructions on pages 21.
Intended use of the 24V Lithium-Ion Cordless Hammer Drill
NOTE: This product is for private domestic DIY use only.
It is not suitable for commercial or trade use.
This drill/driver is mainly used for drill/driving in wood or metal sheet,
hammer drilling into non aggregate concrete, and screwdriving. Use the
tool and accessories only for intended applications.
Contents of carton
1 x 24V Lithium-Ion Hammer
Drill/driver
1 x 24V Lithium-Ion Battery
1 x 1 Hour Charger Base
1 x Plug Pack Charger
1 x Belt Clip + easy assembly screw
(not fitted)
4
2
1 x Carry Strap (fitted)
1 x Instruction manual
1 x Warranty card and certificate
1 x Quick Start Guide
Description of symbols
Li-ion
The instruction manual, rating plate, or on the product itself, may show
these symbols. These represent important information about the product
or instructions on its use.
Wear eye protection.
Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
Double insulated for additional protection.
Regulatory Compliance Mark. Appliance complies with
requirements of electrical approval & EMC in Australia
Read the instruction manual
Waste electrical products should not be
disposed of with household waste
Indoor use
Li ion Battery recycle. Do Not dispose
of in household waste
Ready for use in 1 Hour
Do not put in water
Polarity
MEPS
Caution/Warning: Read all safety warnings and all instructions
2A Fuse
3
General safety warnings
WARNING. Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/
or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains operated (corded)
power tool or battery-operated (cordless) power tool.
This unit may not be used by people (including children) with reduced physical,
sensory or mental capacities, with a lack of experience and without the appropriate
knowledge, unless they are supervised by someone who is responsible for their
safety or have been instructed by such a person with regard to how the unit is to
be operated.
Children should be supervised to ensure that they do not play with the device.
1. Work area safety
a. Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the
presence of ammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical Safety
a. Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
4
General safety warnings
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f. If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when
operating a power tool.
Do not use a power tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust masks, nonskid safety shoes, a hard hat, or hearing
protection used for appropriate conditions will reduce the risk of personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in the off position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
5
General safety warnings
g. Keep handles dry, clean and free from oil and grease. Slippery handles do
not allow for safe handling and control of the tool in unexpected situations.
h. If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of these devices can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it
was designed.
b. Do not use the power tool if the switch does not turn it on and o. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c. Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
d. Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
6
4. Power tool use and care
a. Do not force the power tools. Use the correct power tool for your
General safety warnings
application. The correct power tool will do the job better and safer at
the rate for which it was designed.
a. Do not use the power tool if the switch does not turn it “on” and
“o”. Any power tool that cannot be controlled with the switch is
5. Battery tool use and care
dangerous and must be repaired.
a) Recharge only with the charger specied by the manufacturer. A charger
a. Disconnect the plug from the power source and/or the battery
that is suitable for one type of battery pack may create a risk of fire when used
pack from the power tool before making any adjustments,
with another battery pack.
changing accessories, or storing power tools. Such preventive
b) Use power tools only with specically designated battery packs.
safety measures reduce the risk of starting the power tool accidentally.
Use of any other battery packs may create a risk of injury and fire.
a. Store idle power tools out of the reach of children and do not
c) When battery pack is not in use, keep it away from other metal objects,
allow persons unfamiliar with the power tool or these instructions
like paper clips, coins, keys, nails, screws or other small metal objects,
to operate the power tool. Power tools are dangerous in the hands of
that can make a connection from one terminal to another. Shorting the
untrained users.
battery terminals together may cause burns or a fire.
a. Maintain power tools with care. Check for misalignment or binding
d) Under abusive conditions, liquid may be ejected from the battery; avoid
of moving parts, breakage of parts and any other condition that may
contact. If contact accidentally occurs, flush with water. If liquid contacts eyes,
affect the power tool’s operation. If damaged, have the power tool
additionally seek medical help. Liquid ejected from the battery may cause
repaired before use. Many accidents are caused by poorly maintained
irritation or burns.
power tools.
6. General safety information for battery-powered drill/drivers.
a. Keep cutting tools sharp and clean. Properly maintained cutting
Service
tools with sharp cutting edges are less likely to bind and are easier
to control.
a. Have your power tool serviced by a qualied repair person using only
identical replacement parts. This will ensure that the safety of the power
a. Use the power tool, accessories and tool bits etc. in accordance
tool is maintained.
with these instructions, taking into account the working
conditions and the work to be performed. Use of the power tool for
7. Drill safety warnings:
operations different from those intended could result in a hazardous
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause
situation.
personal injury.
Hold power tool by insulated gripping surfaces, when performing an
operation where the cutting accessory may contact hidden wiring. Cutting
accessory contacting a “live” wire may make exposed metal parts of the power
tool “live” and could give the operator an electric shock.
8. Safety notes for battery/charger.
a. Keep the charger away from rain or damp conditions. Water entering into
the charger will increase the risk of an electrical shock.
7
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
b. Only use chargers recommended by the manufacturer to recharge the
battery. There is a risk of fire if it is used with other batteries.
c. Never use to recharge third-party batteries. The charger is only designed
to charge the supplied batteries (Li-Ion) using the voltages specified in the
Technical Data. Otherwise there is a risk of fire or explosion.
d. Keep the charger clean. Contamination will increase the risk of an electrical
shock.
e. Check the charger, cable and plug each time you use the unit. Do not use
the charger if you find any damage. Never open the charger up yourself, have
it repaired by a qualified specialist only and with original replacement parts.
A damaged charger, cable or plug will increase the risk of an electrical shock.
f. Never operate the charger on a surface that will burn easily (for example,
paper, textiles etc) or in a ammable environment. There is a risk of fire
occurring as a result of the heat generated during the charging process.
g. Fluid can escape from the battery when used incorrectly. Avoid all contact
with this. In the event of accidental contact, rinse with water. If liquid should
get into the eyes, get medical assistance. Battery fluid may result in skin
irritations and burns.
h. Do not open the battery. There is a risk of short-circuiting.
i. Protect the battery from heat, for example, from constant sun and re.
There is a risk of explosion.
j. Never short circuit the battery. There is a risk of explosion.
k. In the event of damage and incorrect use, vapours may come out of
the battery. Ensure your work space is well ventilated with fresh air and, if
you have any symptoms, consult a doctor. These vapours may irritate the
respiratory system.
Safety rules for cordless drill/driver
a) Hold tool by insulated gripping surfaces when performing an operation
where the drill/driver bits may contact hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal parts of the tool “live” and
shock the operator.
b) Always wear safety goggles or eye protection when using this tool.
Use a dust mask or respirator for applications which generate dust.
c) Secure the material being drill/drivered. Never hold it in your hand or
across legs. Unstable support can cause the drill/driver bit to bind causing loss
of control and injury.
8
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
d) Position yourself to avoid being caught between the tool or side handle
and walls or posts. Should the bit become bound or jammed in the work,
the reaction torque of the tool could crush your hand or leg.
e) If the bit becomes bound in the workpiece, release the trigger
immediately, reverse the direction of rotation and slowly squeeze the trigger
to back out the bit. Be ready for a strong reaction torque. The drill/driver body
will tend to twist in the opposite direction as the drill/driver bit is rotating.
f) Do not grasp the tool or place your hands too close to the spinning chuck
or drill/driver bit. Your hand may be lacerated.
g) When installing a drill/driver bit, insert the shank of the bit well within
the jaws of the chuck. If the bit is not inserted deep enough, the grip of the
jaws over the bit is reduced and the loss of control is increased.
h) Do not use dull or damaged bits and accessories. Dull or damaged bits
have a greater tendency to bind in the workpiece.
i) When removing the bit from the tool avoid contact with skin and use
proper protective gloves when grasping the bit or accessory. Accessories may
be hot after prolonged use. Check to see that keys and adjusting wrenches are
removed from the drill/driver before switching the tool on. Keys or wrenches
can fly away at high velocity striking you or a bystander.
j) Do not run the drill/driver while carrying it at your side. A spinning drill/
driver bit could become entangled with clothing and injury may result.
WARNING! Some dust created by power sanding, sawing, grinding, drill/
driving, and other construction activities contains chemicals known to cause
cancer, birth defects or other reproductive harm. Some examples of these
chemicals are:
a) Lead from lead-based paints,
b) Crystalline silica from bricks and cement and other masonry products,
and
c) Arsenic and chromium from chemically treated lumber.
Your risk from these exposures varies, depending on how often you do this
type of work. To reduce your exposure to these chemicals: work in a well
ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
11
9
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
Additional safety rules for charger & batteries
a) Use only the charger and batteries supplied in this pack.
b) Protect the charger and battery pack against moisture including rain and
high humidity.
c) Always check that the power cord is correctly connected before using the
charger.
d) When you are not using the charger, remove the plug from the mains
socket. Do not pull the plug out by the power cord.
e) Handle the battery pack carefully. Do not let it fall or be subject to impact.
f) Always remove the plug from the power socket before you clean or
maintain the charger or battery pack.
g) Do not charge the battery pack if the ambient temperature is less than
4°C or greater than 40°C.
h) Do not short circuit the battery pack. A short circuit gives rise to a heavy
current causing overheating and the possibility of fire or explosion.
i) Do not connect a cable to the battery pack terminals.
j) Make sure that no metal objects such as a nail, paper clip or coin nds its
way into the charging socket.
k) A damaged battery pack or one which no longer holds its charge must
be disposed of in a special way and not placed for normal household
rubbish collection.
l) Never throw a battery pack into a re or into water.
Wear eye protection.
Wear ear protectors when impact drilling.
Exposure to noise can cause hearing loss.
10
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
13
11
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 51887 • 06/2016 • 51887
(toll free)
12
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
Parts List
Parts List
1. Drill/driver chuck
2. Torque setting (including
Hammer function)
3. Two speed high /low gear
selector
4. Forward / Reverse control
5. Belt Clip
6. Rechargeable battery
7. Battery release button
2
8. Plug pack charger
9. Variable speed & On/Off
trigger switch
10. LED Work Light
11. 1 Hour Charger base
(Battery shown in charger is for visual
purposes. Only 1 x 24V Battery is supplied
with this product)
1 2
10
9
8
3
4
7
11
5
6
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
13
Product Care
Important information – Product care
This drill/driver uses Lithium Ion Battery Cells. Care MUST be taken to ensure
both the safety and life of the pack is maintained. Ensure you have read all of
the safety notes in the previous pages before using the drill/driver.
Treat the battery pack with care and within the guidelines of this manual.
If the pack does become immersed in water or any fluids, or is subject to
a severe drop or it does not operate within the guidelines of this manual,
immediately STOP using the battery pack and have it checked.
During operation avoid overloading the drill/driver. If the drill/driver is
overloaded it will automatically STOP. Overloading may occur for a number
of reasons including when the drill/driver is pushed too hard or when using
a drill/driver bit or attachment greater than what is specified. If you do
overload the drill/driver during operation refer to the “Overload” section in
this manual.
NOTE: When the battery of the drill/driver is at the lower end of the charge,
the drill/driver is more susceptible to the overload condition.
Running the drill/driver at close to maximum load, or continual resetting
of the overload will cause the battery pack to overheat. When a preset cell
temperature is detected, the battery pack will automatically STOP operating
and will not restart until the battery pack has cooled to a safe level.
In this condition, DO NOT force cool the pack by placing in a freezer or
similar device. Refer to the “Overload” section in this manual.
Another feature of the drill/driver/battery pack is the low voltage cut out
feature. This feature operates when the voltage drops below a preset value.
When this occurs the tool will automatically stop operating. To correct the
situation you need to either insert another charged battery into the drill/
driver or recharge the existing battery, and then proceed with the drill/
driving application.
NOTE: Attempting to restart the tool in this condition without either
recharging the battery or installing a battery with charge will lead to drill/
driver restarting and then stopping again after only a few seconds of
operation.
These safety devices have been fitted for the safety, reliability and life of the
tool.
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 51887 • 06/2016 • 51887
(toll free)
14
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
Battery Fitting / Battery Charging
Fitting and removing the battery pack
A.
1. To install the battery pack to the tool, align the
raised portion of the battery pack (6) with the
grooves on the bottom of the drill/driver, and
slide it firmly into the handle until you hear
the battery release button snap into place (Fig A).
2. To remove the battery pack from the tool, press
the battery pack release button (7) and slide the
battery pack comp letely out of tool handle
(Fig B).
B.
When inserting the battery pack into the
charger, make sure the pack is fully seated in the
charger.
To remove the battery pack from the charger
base, press the battery release button and slide
the battery out.
Battery charging
IMPORTANT. Before attempting to charge the battery, check the charger
and the battery to ensure the charging equipment matches the battery
supplied. The components are all labelled with component numbers.
CAUTION! The rechargeable battery is not fully charged on leaving the
factory. Charge the rechargeable battery for approx. 1 hour before first use,
or until fully charged as indicated by the red light going off on the charger.
CAUTION! The working temperature of the charger is 0°C to 45°C.
NOTE: If the battery pack is incorrectly orientated the battery will not fully
enter the base as depicted.
1. Connect the power supply from the charger plug pack (8) to the charger
base (11) via plugging the plug from the charger plug pack into the
charger base housing.
2. Plug in the charger plug pack (8) and switch on at the power supply. The
Green LED power indicator located on the charger base will indicate that
the charger base (11) has power connected to it.
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
15
Speeds
The small LED indicator on the plug
pack charger (8) will also illuminate
as a indication the plug pack charger
(8) is on and operating.
3. Align the battery pack with the charger
base (11). Insert the battery pack and
slide it firmly into position (Fig C).
The LED charging light on the charger
will light up RED during the charging
process. When the battery is fully
charged, the RED light will go off.
The battery will be ready for use after
approximately 1 hour.
The Green light will remain on until the
charger plug pack is turned off
or disconnected.
2 Speed gearbox
The 2 Speed Gearbox allows you to select a
gear with the optimum speed and torque
to suit the application.
NOTE: When changing the drill/driver
selector ensure the drill/driver is not
operating.
To select the LOW gear (low speed, high
torque setting), push the gear selector (3)
backward, towards the back of the drill/
driver. The number “1” will be displayed
(Fig D).
To select the HIGH gear (high speed, low
torque setting), push the gear selector (3)
forward, towards the chuck.
The number “2” will be displayed. (Fig D)
C.
D.
2
The picture here shows
the gear selector forward
so the drill/driver is in
High speed, with the
number 2 displayed.
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 51887 • 06/2016 • 51887
(toll free)
16
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
Usig the Drill / Driver
Using the drill/driver
Trigger switch
Use the forward/reverse switch (4) to select the
direction of rotation (Fig E), then pull the trigger (9)
(Fig F). This trigger switch is an electronic variable
speed control which enables the user to vary the
speed continuously.
The speed varies according to how far the trigger
switch is depressed.
The further it is depressed the faster the chuck will
rotate and the lighter it is depressed, the slower it
will rotate.
To stop the drill/driver, release the trigger switch (9).
Note. The variable speed control fitted to this drill/
driver is NOT intended to be used for long periods
of time during the operation of the task being
performed. Use the variable speed to start drill/
driving and screwing tasks, and then fully depress the trigger once the task
has started.
CAUTION. Extended use of the variable speed under load will overload and
then permanently damage the speed control.
E.
F.
Drill/driver Overload
This drill/driver is fitted with an overload protection. If the drill/driver is
excessively forced, or the task being performed is too great for the drill/
driver, the drill/driver will automatically go into an overload mode. When
the drill/driver goes into overload, the drill/driver will automatically and
suddenly STOP. To reset the overload, simply release the trigger. When the
trigger is pressed again, the drill/driver will restart. Resume work after the
overload has been reset, but reduce the load by using a smaller drill/driver
bit or re-sharpen the existing drill/driver bit and reduce the amount of force
placed on the drill/driver. If the drill/driver is set to High speed on the gear
selector, consider changing to low speed selection.
CAUTION. Do not continue to overload the drill/driver and constantly reset
the overload. Doing this will cause the battery cells to over heat.
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
17
Temperature Cut out
Temperature cut out
If the drill/driver is constantly overloaded, or the drill/driver is used
constantly at maximum rating in high ambient conditions, the battery cells
may overheat causing the battery pack to shut down.
When this occurs you will need to immediately stop drill/driving and allow
the battery cells to reduce the temperature.
NOTE: The drill/driver will not restart until the battery pack has cooled.
To reduce the temperature of the cells remove the battery pack from the
drill/driver and place the battery pack in a free air environment, out of direct
sunlight or any other heat source.
DO NOT force cool the pack in any way. Do not place in refrigerators or
freezers.
When the battery pack has cooled down it can again be used to operate
the drill/driver, as long as the load or the conditions causing the original
excessive temperature has been corrected.
Low voltage cut out
The battery pack used on this tool is fitted with a low voltage cut out feature
within the circuitry.
The low voltage cut out feature operates when the voltage drops below a
preset value. This feature automatically stops the drill/driver from operating
(similar to that of the overload condition). When this condition occurs you
will need to either insert another battery into the drill/driver or recharge the
existing battery.
The low voltage cut out feature has been added to maximise the tool’s
life. When this occurs, recharge the battery pack by following the battery
charging section in this manual.
NOTE: Attempting to restart the tool without either recharging the battery
or installing another battery (with charge) will lead to drill/driver restarting
and then stopping again, after only a few seconds of operation.
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 51887 • 06/2016 • 51887
(toll free)
18
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
Forward/Reverse
Forward/reverse switch
NOTE: You can only change the direction of rotation of the drill/driver using
the forward/reverse switch when the trigger is NOT depressed.
This switch will allow you to change the direction of the motor while the
trigger switch is not depressed.
Drill/driving uses the forward mode. The reverse mode is intended for the
removal of screws and assisting to remove jammed drill/driver bits.
Adjustable torque
This drill/driver is equipped with 18 torque settings plus 1 x drill/driver
setting and 1 x hammer setting, which are controlled by the torque collar
(2). All of the torque settings are clearly identified on the torque collar (2).
To adjust the torque setting you rotate the torque collar. The higher the
number, the higher the torque setting collar (2).
Controlling the torque allows for better control when using the drill/driver
on specific add screwing tasks and prevents over-fastening and overtightening.
For drill/driving, always use the drill/driver position
by aligning the drill/driver symbol with the
triangular indicator on the front face of the drill/
driver near the torque collar.
For setting the torque position, select a low setting
on the torque collar (2) and align the selected
symbol with the triangular indicator on the top
of the drill/driver.
G.
Using the Hammer function
To select the hammer drill position, rotate the torque collar (2) around past
the drill symbol and align the hammer symbol with the indicator on the top
of the drill (Fig G). This will allow the drill to hammer during rotation of the
chuck when pressure is applied.
When fitting the drill bit, ensure to use a masonry drill bit or a drill bit
specifically designed for the material being drilled.
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
19
Inserting//Removing bits
Inserting and removing bits
H.
This drill/driver has a keyless chuck, which means
that a chuck (1) key is not needed to secure a bit
in the drill/driver.
Open the chuck (1) by unscrewing it in an
anti-clockwise direction, holding the drill/driver as
shown (Fig H).
Do this sufficiently enough to allow the drill/driver
bit to enter the jaws of the chuck.
Ensure the drill/driver bit is fully inserted, so that the chuck jaws grip the
straight section of the bit.
Rotate the chuck clock-wise until the jaws tighten on the drill/driver bit.
The collar of the chuck needs to be tightened firmly to ensure the drill/driver
bit is held securely.
To remove the drill/driver bit, rotate sharply the chuck in an anti-clockwise
direction, sufficiently enough to allow the drill/driver bit to be removed.
NOTE: This device is fitted with spindle lock and the chuck is a onehanded
operation.
Drill/driving
Drill/driving metals
• Alwaysclampsheetmetal.
• Supportthinmetalwithablockofwoodtoavoiddistortingit.
• Useapunchtomarkthecentreofthehole.
• Useasuitablelubricantforthematerialyouareworkingon,
USE: FOR:
Oil Steel
Turpentine or paraffin Aluminium
Do not lubricate Brass, copper or cast iron
Do not Lubricate Concrete based material
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 51887 • 06/2016 • 51887
(toll free)
20
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
Operation
Drill/driving plastics and plastic coated chipboard
• Usehighspeeddrill/driverbits
• Seedrill/drivingwoodbelow
Drill/driving wood
• Clampapieceofscrapwoodtothebackofyourworktoprevent
splintering.
Hammer drill operations.
• Wherepossible,useHighspeed.
• Selectthehammerpositiononthetorquecollar.
• Usedrillbitsspecicallyformasonaryapplications.
• Ensuretowearsafetyglasses.
All drill/driving operations
• Markothecentreoftheholeusingacentrepunchornail.
• Don’tforcethedrill/driver,letitworkatitsownpace
• Keepthedrill/driverbitsharp.
• Reducepressure,asthedrill/driverisabouttobreakthroughtheitem
being drill/drivered.
LED work light
When the unit is switched on, the LED work light (10) also comes on to
ensure better vision and to make working in dark areas more safe.
The working light goes out when the On/Off switch (9) is released.
CAUTION! LED is laser class 1!
Do not look directly into the laser as this may result in damage to the eyes.
Chuck replacement
The chucks of reversible drill/drivers are always fixed by a screw with a lefthand thread. The screw, which is located in the centre of the chuck, must
be removed before the chuck can be removed. To remove the screw, turn it
in a clockwise direction. The chuck can now be removed by unscrewing it
anti-clockwise. If you have trouble removing the chuck take the drill/driver
to your nearest authorised service centre for chuck replacement.
CAUTION. Always ensure that the drill/driver is switched off and the battery
pack is removed before making any adjustments.
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
21
Operatiion/Cleaning/Maintenance
Belt clip
I.
The belt clip (5) is used to assist to clip the tool to
your waist belt while working. Install the clip to
the drill/driver by locating the belt clip tabs in the
slots in the drill/driver and tighten the screw to fix
the clip firmly (Fig I).
Cleaning
Clean the case only with a damp cloth. DO NOT
use solvents when cleaning plastic parts. Plastics
are susceptible to damage from various types of commercial solvents and
may be damaged by their use. Use a clean cloth to remove dirt, dust, oil,
grease etc, then dry well.
Maintenance
To maintain capacity, we recommend completely discharging and
recharging the battery every two months. Store only fully charged batteries.
They should therefore be recharged from time to time. The place of storage
must be dry; the ambient temperature must not fall below 0°C or rise above
40°C.
CAUTION! Electrical and battery operated units that no longer work
should not be disposed of in the household waste! They are to be collected
separately, in accordance with your local waste disposal regulations.
ATTENTION! Batteries must be removed from batterypowered tools and
disposed of separately in accordance with relevant wastebattery regulations.
Batteries must never be disposed of with domestic waste!
Please discard power tools no longer usable at a local collection point.
Collection and disposal of packaging materials separately by types
complying with local rules and regulations. For details, please contact your
local council.
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 51887 • 06/2016 • 51887
(toll free)
22
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
Warranty/Service
Warranty
Your new Workzone® Titanium 24V Lithium-Ion Cordless Drill will more than
satisfy your expectations.
It has been manufactured under stringent Workzone® Quality Standards to
meet superior performance criteria.
You will find your new 24V Lithium-Ion Cordless Drill easy and safe to
operate, and, with proper care, it will give you many years of dependable
service.
CAUTION. Carefully read through this entire instruction manual before
using your new Workzone® Titanium 24V Lithium-Ion Cordless Drill.
Take special care to heed the Cautions and Warnings.
Your Workzone® Titanium 24V Lithium-Ion Cordless Drill has many
features that will make your job faster and easier. Safety, performance, and
dependability have been given top priority in the development of this
Chainsaw , making it easy to maintain and operate.
Use only Workzone® Titanium replacement parts for your product.
Non-conforming parts or modifications made to parts will void your
warranty.
Service Support
If you have any issues with the operation of your product, please call us on
1800 909 909 for advice, or email us at help@powertoolsupport.com
Accessories
The following accessories are available for purchase by visiting
www.extrabattery.com.au or calling our customer service hotline on:
1800 909 909
•Replacement24VBattery(24VACH15B)
•ReplacementPlugPackCharger(24VACHPC)
•ReplacementChargerBaseAdaptor(24VACH1H)
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
23
Environmental Protection
Environmental protection
Recycle unwanted materials instead of disposing of them as waste.
All tools, hoses and packaging should be sorted, taken to the local
recycling centre and disposed of in an environmentally safe way.
Dispose of used motor oil in a manner that is compatible with the
environment.
We suggest you take it in a sealed container to your local service station for
reclamation. Do not throw it in the trash or pour it into the earth.
What your 3 year warranty means
Great care has gone into the manufacture of this product and it should
therefore provide you with years of good service when used properly.
In the event of product failure within its intended use over the course of
the first 3 years after the date of purchase, we will remedy the problem as
quickly as possible once it has been brought to our attention. In the unlikely
event of such an occurrence, or if you require any information about the
product please contact us via our after sales support services, details of
which can be found in this manual and on the product itself.
After Sales Support TEL: 1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 51887 • 06/2016 • 51887
(toll free)
24
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
Trouble Shooting
FAQ/Troubleshooting
Do I need to charge the battery before use?
Yes, New battery packs are shipped in a low charge condition and must be fully charged
before use. It takes approximately 1 hour to fully charge your new battery. Charging of
batteries should not be undertaken casually. Through the charging cycle the condition of
the battery pack should be monitored and the charge cycle turned off at completion or at
the end of the recommended time.
How do I obtain the best life for the battery?
- Never allow the drill to come to a complete stand still before recharging. The battery
should be placed on charge whenever the battery is noticeably running down or the drill
no longer performs a task it previously performed.
- Avoid allowing lose items like screws or nails etc. to be stored with battery packs as these
or similar items can short battery packs and cause a fire or explosion.
- Always unplug the plug pack charger when not in use and store in a dry secure place.
- Avoid charging or storing your battery in temperatures below 0ºC and above 40ºC.
How do I use the 2 gears on the drill?
To select the LOW gear (low speed, high torque setting), push the gear selector backward,
towards the back of the drill/driver. The word LO will be displayed.
To select the HIGH gear (high speed, low torque setting), push the gear selector forward,
towards the chuck. The word HI will be displayed.
How do I adjust the torque?
To adjust the torque setting you rotate the torque collar. The higher the number, the higher
the torque setting collar.
Controlling the torque allows for better control when using the drill/driver on specific add
screwing tasks and prevents over-fastening and over-tightening.
For drill/driving, always use the drill/driver position by aligning the drill/driver symbol with
the triangular indicator on the front face of the drill/driver near the torque collar.
For setting the torque position, select a low setting on the torque collar and align the
selected symbol with the triangular indicator on the top of the drill/driver.
How do I select hammer function?
Rotate the torque collar until the Hammer symbol aligns with the triangular indicator.
What is the function of the Forward / Reverse switch?
This switch will allow you to change the direction of the motor while the trigger switch is
not depressed.
Drill/driving uses the forward mode. The reverse mode is intended for the removal of
screws and assisting to remove jammed drill/driver bits.
What do I do if I have an issue with my drill?
If you have any issues with your drill/driver, please contact our Customer Service line on
1800 909 909.
AFTER SALES SUPPORT
(toll free)
e-mail: help@powertoolsupport.com1800 909 909
24v Lithium-ion Cordless Drill with Hammer Action
MODEL: №. 51887 • 06/2016 • 51887
25
Specications
Motor: 24 V–...
Low speed: n0-Lo = 0 – 400 minHigh speed: n0-Hi = 0 – 1100 min-
Impact Frequency: 0-5200 / 0-14,300 BPM
Drill/driver diam Ø: - Wood 28 mm
- Steel 10 mm
Chuck: 13 mm Keyless
Battery (24VHA15B): 24 V
–
... 1.5Ah/Li-Ion
Charger: Model: 24VACHPC (JLH292551400S)
Input: 100-240VAC 50-60Hz 50W
Output: 25.5Vdc 1400mA
Charger Base Adaptor: Model: 24VACH1H
Charging time: Ready for use in 1 Hour
Product Dimensions: 220mm x 225mm x 75mm (L x W x H)
(Drill/driver with battery pack fitted)
1
1
Specifications
This product complies with:
Plug Pack Charger:
EMC: EN 55014-1:2006/+A1:2009/+A2:2011
Safety Standard: AS/NZS 60335.2.29:2004 including A1-2
AS/NZS 60335.1.2011 including A1
MEPS: AS/NZS 4665.1:2005+A1:2009&4665.2:2005+A1:2009
Certificate: SAA-150353-EA
Drill:
EMC EN 55014-1:2006+A1:2009+A2:2011
EN 55014-2:1997+A1:2001+A2:2008
Safety Standard: EN 60745-1:2009 + A11:2010
EN 60745-2-1: 2010
EN60745-2-2: 2010
24v Lithium-ion Cordless Drill with Hammer Action
AFTER SALES SUPPORT
e-mail: help@powertoolsupport.com
1800 909 909
MODEL: №. 51887 • 06/2016 • 51887
(toll free)
MODEL: 51887 • 06/2016 • 24VHA
1800 909 909 (toll free)
e-mail: help@powertoolsupport.com
ALDI guarantees that our exclusive brand products are developed to
our stringent quality specifications. If you are not entirely satisfied with this
product, please return it to your nearest ALDI store, within 60 days from
the date of purchase, for a full refund or replacement, or take advantage of
our after sales support by calling the supplier’s Customer Service Hotline.
Made in China
Workzone® Titanium is a registered trademark of ALDI Stores
DISTRIBUTED BY:
ALDI STORES
1 SARGENTS ROAD
MINCHINBURY NSW 2770
www.aldi.com.au
26
Loading...