Wonde Proud Technology WPSPT10 Users Manual

WoonnddeeXX SSPPTT 1100
W
Hardware Quick Installation Guide
VVeerrssiioonn:: 11..0033
DDaattee:: 1122//2244//22000088
WONDE PROUD TECHNOLOGY.
General Notes:
All materials contained on this documentation is protected by the copyright law and may not be reproduced, transmitted, published or broadcasted without the prior obtaining authorization of Wonde Proud Technology. The documentation is provided for testing, evaluation, integration and product information purpose and it may contain deficiencies or inadequacies information of products. This product is not intended for use in life support appliance, devices or systems where a malfunction of the product can reasonably be expected to result personal injury. Wonde Proud or its supplier will not be liable for any consequential, direct, indirect, incidental, punitive or other damages including without limitation, damages for loss of business profits, business interruption, loss of business information or other pecuniary loss that arising out the use of or inability to use the documentation or product, even if Wonde Proud has been advised of the possibility of such damages. The customers using or reselling the product in such application do so at their own risk and agree to full indemnify Wonde Proud for any damages resulting from illegal use or resale. Subject to change without notice at any time.
Copyright
Reproduction, dissemination, edition of this document, or utilization of the content and communication format as well as giving to other without authorization are prohibited. Offenders will be held liable for payment of damages.
Copyright ©Wonde Proud Technology 2007. All right are reserved.
Copyright © Wonde Proud Technology. 2007. All rights are reserved. of 7
WONDE PROUD TECHNOLOGY.
TTaabbllee ooff CCoonntteenntt
1. Safety Instruction:............................................................................................................................4
2. Introduction of Hardware:................................................................................................................4
3. Insert the SIM Card:.........................................................................................................................4
4. Insert the Backup Battery.................................................................................................................5
5. Connect “USB” Cable......................................................................................................................5
6. LED Indicators:................................................................................................................................6
7. About Wonde Proud Technology:....................................................................................................7
Copyright © Wonde Proud Technology. 2007. All rights are reserved. of 7
WONDE PROUD TECHNOLOGY.
11.. SSaaffeettyy IInnssttrruuccttiioonn::
Please read below safety instruction carefully before use this device.
This device complies with Part 22, 24 of the FCC Rules. Operation is subject to the
following two conditions:
This device may not cause harmful interference, and (2) This device must accept any
interference received, including interference that may cause undesired operation.
22.. IInnttrroodduuccttiioonn ooff HHaarrddwwaarree::
Mini USB Connector
Power Switch
33.. IInnsseerrtt tthhee SSIIMM CCaarrdd::
Please follow the steps below to insert the SIM Card correctly.
a. Unscrew the back cover of device and pull out the lid. b. Uplift the battery (if the battery is connected to the device) c. Unlock the SIM card slot by sliding the
holder toward the “OPEN” direction.
d. Place the SIM card into the SIM card holder. e. Lock the SIM card slot by sliding the holder
toward the “LOCK” direction.
f. Then, put back the battery and screw the back
cover of the device.
Please ensure the SIM card is well placed in the holder and well contacted; otherwise, the
SOS Button
device might not detect the SIM card successfully.
Copyright © Wonde Proud Technology. 2007. All rights are reserved. of 7
WONDE PROUD TECHNOLOGY.
44.. IInnsseerrtt tthhee BBaacckkuupp BBaatttteerryy
Please follow the steps below to insert the backup battery correctly.
a. Unscrew the back cover of device and pull out the
lid.
b. Connect the metal side of the battery to socket in the
corner and place the battery well.
c. Then, put the cover of the device back and screw it
well.
55.. CCoonnnneecctt ““UUSSBB”” CCaabbllee
USB Cable can be used for the unit configuration or connected to the PC/Car Charger to charge.
Notes:
1. Please fully charge the device before further usage after receiving the device.
2. While connecting to the PC to configure the device, please ensure the power button
is switched to “on” status. Otherwise, the PC will not recognize the device.
Copyright © Wonde Proud Technology. 2007. All rights are reserved. of 7
WONDE PROUD TECHNOLOGY.
66.. LLEEDD IInnddiiccaattoorrss::
- From the Top to the Bottom: GPS, Power, GSM
Indicators Status Blinking Behavior
power saving Off GPS (Blue)
Power (Red)
GSM (Green)
GPS error 150ms on/150ms off
GPS positioning 50ms on/ 450ms off
GPS fixed 50ms on/ 2 seconds off
power saving 50ms on/ 6 seconds off
charging 1 second on/1 second off
charging completed On
low battery 50ms on/ 450 ms off
normal 50ms on/ 2 seconds off
power saving Off
PIN code error/lock 150ms on/ 150ms off
NO SIM Off
GPRS connecting 50ms on/ 200ms off/ 50ms on/
1700ms off normal 50ms on/ 2 seconds off GSM Searching 50ms on/ 450ms off
* USB connecting: GPS LED (Blue)/Power LED (Red)/GSM LED (Green): Sequence ON/OFF * As the device is fully charged, the Power LED (Red) will be always in ‘on’ status.
Copyright © Wonde Proud Technology. 2007. All rights are reserved. of 7
WONDE PROUD TECHNOLOGY.
77.. AAbboouutt WWoonnddee PPrroouudd TTeecchhnnoollooggyy::
WondeX SPT10 device is manufactured by Wonde Proud Technology. Wonde Proud Technology provides advanced solution for GPS related solutions including the various GPS components, Automatic Vehicle Location (AVL) device (data logger & real time tracking devices). Please contact us at the phone and fax number list below or visit our website for further product information.
Wonde Proud Technology
Web site: http://www.wondeproud.com Tel: +886-2-26968498 Fax: +886-2-26968499 Address: 4F., No.100,Sec.1,Shin Tai Wu Rd, Sijhih city, Taipei county 22102,
Taiwan. R.O.C
Copyright © Wonde Proud Technology. 2007. All rights are reserved. of 7
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).
RF Exposure Information (SAR)
This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. Tests for SAR are conducted using standard operating positions accepted by the FCC with the device transmitting at its highest certified power level in all teste d frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the device while operating can be well below the maximum value. This is because the device is designed to operate at multiple power levels so as to use only the poser required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. The highest SAR value for the device as reported to the FCC when worn on the body is 0.549 W/kg for PCS Body SAR. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement.
This device complies with Part 22, 24 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Loading...