Page 1
NEW GENERATION
INTERNATIONAL DESIGN GUIDE
Page 2
Contents
3 M Series Ovens
12 E Series Ovens
19 Convection Steam Ovens
24 Gas Cooktops
28 Coffee Systems
33 Downdraft Systems
39 Wolf Warranty
Features and specications are subject to change at any
time without notice. Visit wolfappliance.com/specs for the
most up-to-date information.
IMPORTANT NOTE: Throughout this guide, dimensions may
vary by ± 3 mm.
2 | English
Page 3
WOLF M SERIES OVENS
UPPER OVEN LOWER OVEN
M Series Ovens
Three striking new looks are just the beginning. Superior
performance features include an even more advanced dual
vertical convection fan system, touch-screen controls,
convenient new preset cooking programs, improved interior
lighting, and even redesigned hinges. There is more usable
space inside for deliciousness on a grand scale.
KEY FEATURES
• Dual VertiCross™ convection system supplies two corner
column fans for best heat saturation and distribution.
• Nine cooking modes, including the bake stone and
dehydration kits for precise, easy-to-use control.
• Self-cleaning ovens.
• Full-extension racks allow easy access to foods.
• Spring and damper door hinge system for smooth
opening and closing of the door.
M SERIES OVENS
TRANSITIONAL
ICBSO27TM/S/TH
ICBDO27TM/S/TH
PROFESSIONAL
ICBSO30TM/S/TH
ICBDO30TM/S/TH
ICBSO36TM/S/TH
ICBSO30PM/S/PH
ICBDO30PM/S/PH
CONTEMPORARY
ICBSO30CM/B
ICBDO30CM/B
wolfappliance.com | 3
Page 4
WOLF M SERIES OVENS
M Series Ovens
TRANSITIONAL SINGLE OVEN
723
mm
W
WIDTH
65
mm
TRANSITIONAL DOUBLE OVEN
22
mm
51
mm
36 mm
CONDUIT
CHANNEL
584 mm
BEHIND FRAME
22
mm
51
mm
36 mm
CONDUIT
CHANNEL
218
mm
218
mm
686
mm
46 mm
OPEN OVEN DOOR
46 mm
543
mm
1291
mm
W
WIDTH
65
mm
584 mm
BEHIND FRAME
WIDTH
TRANSITIONAL W
686 mm Model 683 mm
762 mm Model 759 mm
914 mm Model (single oven only) 911 mm
1254
mm
OPEN OVEN DOOR
543
mm
SPECIFICATIONS
INTERIOR CAPACITY L
686 mm Oven 127
762 mm Oven 144
914 mm Oven 178
INTERIOR DIMENSIONS W H D
686 mm Oven 565 mm 445 mm 505 mm
762 mm Oven 641 mm 445 mm 505 mm
914 mm Oven 794 mm 445 mm 505 mm
AHAM overall volume.
4 | English
Page 5
WOLF M SERIES OVENS
M Series Ovens
PROFESSIONAL SINGLE OVEN
723
mm
759 mm
83
mm
PROFESSIONAL DOUBLE OVEN
UPPER OVEN LOWER OVEN
22
mm
51
mm
36 mm
CONDUIT
CHANNEL
584 mm
BEHIND FRAME
22
mm
51
mm
36 mm
CONDUIT
CHANNEL
218
mm
218
mm
686
mm
46 mm
OPEN OVEN DOOR
46 mm
543
mm
1291
mm
759 mm
83
mm
584 mm
BEHIND FRAME
WIDTH
PROFESSIONAL W
762 mm Model 759 mm
1254
mm
OPEN OVEN DOOR
543
mm
SPECIFICATIONS
INTERIOR CAPACITY L
762 mm Oven 144
INTERIOR DIMENSIONS W H D
762 mm Oven 641 mm 445 mm 505 mm
AHAM overall volume.
wolfappliance.com | 5
Page 6
WOLF M SERIES OVENS
M Series Ovens
CONTEMPORARY SINGLE OVEN
723
mm
759 mm
CONTEMPORARY DOUBLE OVEN
25
mm
51
mm
36 mm
CONDUIT
CHANNEL
584 mm
BEHIND FRAME
25
mm
51
mm
36 mm
CONDUIT
CHANNEL
218
mm
218
mm
686
mm
46 mm
OPEN OVEN DOOR
46 mm
543
mm
1291
mm
759 mm
584 mm
BEHIND FRAME
WIDTH
CONTEMPORARY W
762 mm Model 759 mm
1254
mm
OPEN OVEN DOOR
543
mm
OVEN SPECIFICATIONS
INTERIOR CAPACITY L
762 mm Oven 144
INTERIOR DIMENSIONS W H D
762 mm Oven 641 mm 445 mm 505 mm
AHAM overall volume.
6 | English
Page 7
WOLF M SERIES OVENS
Planning Information
The oven can be installed in a standard or ush inset
application. If a cooktop is being installed above an oven,
a minimum of 6 mm is required between units. Location of
the electrical supply within the oven opening may require
additional cabinet depth. Refer to the chart below.
Finish the edges of the opening. They may be visible when
the door is open.
For ush inset installations, a minimum 3 mm reveal is
required on all sides. To ensure consistent 3 mm reveals,
each corner of the opening must be exactly 90°.
INSTALLATION REQUIREMENTS
BASE SUPPORT
Single Oven 115 kg
Double Oven 181 kg
TRIM OVERLAP
Top 25 mm
Bottom 0 mm
Sides 18 mm
ELECTRICAL
Installation must comply with all applicable electrical codes
and be properly grounded (earthed).
Locate the electrical supply ush with the back wall and
within the shaded area shown in the illustration for your specic installation on the following pages. For ease of installation, the electrical supply for the oven can be placed in an
adjacent cabinet within reach of the conduit.
Performance may be compromised if the electrical supply is
less than 220 volts.
The oven is supplied with a single phase and 3-phase
convertible power inlet box. The wiring diagram covering the
control circuit is provided with the oven.
ELECTRICAL REQUIREMENTS
SINGLE OVEN SINGLE PHASE 3-PHASE
Required Power Supply 220-240 V AC
50/60 Hz
Maximum Connected Load 5.4 kW TBD
Total Amps 22 TBD
DOUBLE OVEN SINGLE PHASE 3-PHASE
Required Power Supply 220-240 V AC
50/60 Hz
Maximum Connected Load 10.8 kW TBD
Total Amps 45 TBD
380-415 V AC
50 Hz
380-415 V AC
50 Hz
wolfappliance.com | 7
Page 8
WOLF M SERIES OVENS
SIDE
NOTE: Location of electrical supply within opening may require additional cabinet depth.
Dashed line represents profile of unit
M Series Single Oven
STANDARD INSTALLATION
699 mm
OPENING
HEIGHT
591 mm
OPENING
DEPTH
TOP VIEW
W
OPENING WIDTH
127
mm
E
102
mm
E
121 mm
TYPICAL
VIEW
.
OPENING WIDTH
MODEL W
686 mm Model 648 mm
762 mm Model 724 mm
914 mm Model 876 mm
FRONT VIEW
8 | English
Page 9
WOLF M SERIES OVENS
SIDE
NOTE: Location of electrical supply within opening may require additional cabinet depth.
Dashed line represents profile of unit
M Series Double Oven
STANDARD INSTALLATION
TOP VIEW
591 mm
OPENING
DEPTH
E
1267 mm
OPENING
HEIGHT
432 mm
TYPICAL
VIEW
.
OPENING WIDTH
MODEL W
686 mm Model 648 mm
762 mm Model 724 mm
W
OPENING WIDTH
FRONT VIEW
127
mm
102
mm
E
E
E
wolfappliance.com | 9
Page 10
WOLF M SERIES OVENS
SIDE
*
**
NOTE: Location of electrical supply within opening may require additional cabinet depth.
Dashed line represents profile of unit.
M Series Single Oven
FLUSH INSET INSTALLATION
730 mm
FLUSH INSET
HEIGHT
22 mm
OR
**
25 mm
TOP VIEW
W
FLUSH INSET WIDTH
29 mm
21 mm
3 mm
610 mm
FLUSH INSET
DEPTH
102
mm
127
mm
FINISHED
CLEATS*
E
E
E
VIEW
25 mm minimum depth. Shaded areas will be visible and should be finished to match cabinetry.
22 mm for professional and transitional models and 25 mm for contemporary model.
FLUSH INSET WIDTH
MODEL W
686 mm Model 689 mm
762 mm Model 765 mm
914 mm Model 918 mm
10 | English
FRONT VIEW
Page 11
WOLF M SERIES OVENS
SIDE
*
**
NOTE: Location of electrical supply within opening may require additional cabinet depth.
Dashed line represents profile of unit.
M Series Double Oven
FLUSH INSET INSTALLATION
1299 mm
FLUSH INSET
HEIGHT
22 mm
OR
**
25 mm
TOP VIEW
W
FLUSH INSET WIDTH
29 mm
21 mm
610 mm
FLUSH INSET
DEPTH
102
mm
127
mm
FINISHED
CLEATS*
E
E
432 mm
TYPICAL
VIEW
25 mm minimum depth. Shaded areas will be visible and should be finished to match cabinetry.
22 mm for professional and transitional models and 25 mm for contemporary model.
FLUSH INSET WIDTH
MODEL W
686 mm Model 689 mm
762 mm Model 765 mm
3 mm
FRONT VIEW
E
wolfappliance.com | 11
Page 12
WOLF E SERIES OVENS
E Series Ovens
Stainless models now feature a redesigned stainless steel
touch-action control panel, helping to create great meals
with ease, as well as adding a striking design feature to the
kitchen. Smart technology gives the E series ten cooking
modes, with Wolf’s innovative dual convection in single
ovens and in the upper unit of double ovens. E series ovens
can be installed ush with cabinets for a contemporary,
integrated look. Wolf E series ovens are crafted of stainless
steel. Tubular oven handles have been updated to match the
rest of the new Wolf cooking appliance offering, providing a
more cohesive family look.
KEY FEATURES
• NEW! Redesigned stainless steel touch control panel.
• Dual convection—two fans for even heat distribution.
• Ten cooking modes, including the bake stone and
dehydration kits for precise, easy-to-use control.
• Self-cleaning ovens.
• Full-extension bottom rack for easier access to foods.
• Balanced door hinge system for smooth opening and
closing of the door.
E SERIES OVENS
TRANSITIONAL
ICBSO30TE/S/TH
ICBDO30TE/S/TH
PROFESSIONAL
ICBSO30PE/S/PH
ICBDO30PE/S/PH
CONTEMPORARY
12 | English
ICBSO30CE/B/TH
ICBDO30CE/B/TH
Page 13
*25 mm
25 mm OR
*25 mm
25 mm
WOLF E SERIES OVENS
E Series Ovens
SINGLE OVEN
*
32 mm
76 mm
CONDUIT
708
mm
759 mm
for professional and transitional models and 32 mm for contemporary model.
73
mm
CHANNEL
603 mm
BEHIND FRAME
DOUBLE OVEN
OR
*
32 mm
76 mm
CONDUIT
1280
mm
CHANNEL
689
mm
1261
mm
225
mm
718 mm
OPEN OVEN DOOR
225
mm
718 mm
244
mm
244
mm
559
mm
759 mm
73
mm
603 mm
BEHIND FRAME
for professional and transitional models and 32 mm for contemporary model.
WIDTH
E SERIES W
762 mm Model 759 mm
OPEN OVEN DOOR
559
mm
SPECIFICATIONS
INTERIOR CAPACITY L
762 mm Oven 127
INTERIOR DIMENSIONS W H D
762 mm Oven 635 mm 419 mm 483 mm
AHAM overall volume.
wolfappliance.com | 13
Page 14
WOLF E SERIES OVENS
Planning Information
The oven can be installed in a standard or ush inset
application. If a cooktop is being installed above an oven,
a minimum of 6 mm is required between units. Location of
the electrical supply within the oven opening may require
additional cabinet depth. Refer to the chart below.
Finish the edges of the opening. They may be visible when
the door is open.
For ush inset installations, a minimum 6 mm reveal is
required on all sides. To ensure consistent 6 mm reveals,
each corner of the opening must be exactly 90°.
INSTALLATION REQUIREMENTS
BASE SUPPORT
Single Oven 115 kg
Double Oven 181 kg
TRIM OVERLAP
Top 13 mm
Bottom 3 mm
Sides 17 mm
ELECTRICAL
Installation must comply with all applicable electrical codes
and be properly grounded (earthed).
Locate the electrical supply ush with the back wall and
within the shaded area shown in the illustration for your specic installation on the following pages. For ease of installation, the electrical supply for the oven can be placed in an
adjacent cabinet within reach of the conduit. Unit is supplied
with terminal box convertible to single or 3-phase.
The wiring diagram covering the control circuit is provided
with the oven.
ELECTRICAL REQUIREMENTS
SINGLE OVEN SINGLE PHASE 3-PHASE
Required Power Supply 220-240 V AC
50/60 Hz
Maximum Connected Load 4.4 kW 4.4 kW
Total Amps 19 19
DOUBLE OVEN SINGLE PHASE 3-PHASE
Required Power Supply 220-240 V AC
50/60 Hz
Maximum Connected Load 7.4 kW 5.1 kW
Total Amps 32 22
380-415 V AC
50 Hz
380-415 V AC
50 Hz
14 | English
Page 15
WOLF E SERIES OVENS
SIDE
NOTE: Location of electrical supply within opening may require additional cabinet depth.
Dashed line represents profile of unit
E Series Single Oven
STANDARD INSTALLATION
692 mm
OPENING
HEIGHT
610 mm
OPENING
DEPTH
TOP VIEW
724 mm
OPENING WIDTH
127
mm
E
102
mm
E
121 mm
TYPICAL
VIEW
.
FRONT VIEW
wolfappliance.com | 15
Page 16
SIDE
NOTE: Location of electrical supply within opening may require additional cabinet depth.
Dashed line represents profile of unit
WOLF E SERIES OVENS
E Series Double Oven
STANDARD INSTALLATION
TOP VIEW
610 mm
OPENING
DEPTH
E
1264 mm
OPENING
HEIGHT
432 mm
TYPICAL
VIEW
.
724 mm
OPENING WIDTH
FRONT VIEW
127
mm
102
mm
E
E
E
16 | English
Page 17
WOLF E SERIES OVENS
SIDE
*W
**25 mm
NOTE: Location of electrical supply within opening may require additional cabinet depth.
Dashed line represents profile of unit.
E Series Single Oven
FLUSH INSET INSTALLATION
721 mm
FLUSH INSET
HEIGHT
981 mm
TYPICAL
25 mm
OR
**
32 mm
TOP VIEW
772 mm
FLUSH INSET WIDTH
19 mm
24 mm
10 mm
635 mm
FLUSH INSET
DEPTH
102
mm
127
mm
FINISHED
CLEATS*
E
E
E
VIEW
ill be visible and should be finished to match cabinetry.
for professional and transitional models and 32 mm for contemporary model.
FRONT VIEW
wolfappliance.com | 17
Page 18
SIDE
*W
**25 mm
NOTE: Location of electrical supply within opening may require additional cabinet depth.
Dashed line represents profile of unit.
WOLF E SERIES OVENS
E Series Double Oven
FLUSH INSET INSTALLATION
1292 mm
FLUSH INSET
HEIGHT
25 mm
OR
**
32 mm
TOP VIEW
772 mm
FLUSH INSET WIDTH
19 mm
24 mm
635 mm
FLUSH INSET
DEPTH
102
mm
127
mm
FINISHED
CLEATS*
E
E
432 mm
TYPICAL
VIEW
ill be visible and should be finished to match cabinetry.
for professional and transitional models and 32 mm for contemporary model.
18 | English
10 mm
FRONT VIEW
E
Page 19
WOLF CONVECTION STEAM OVENS
Convection Steam Ovens
The legacy of the “combination oven” goes back decades,
to innovative chefs in America and Europe who embraced
the combination of air movement with superheated steam to
achieve superior results—from breads and roasts to delicate
shes, seafood and vegetables. Wolf combines the benets
of convection and steam for the most innovative steam oven
on the market today. Virtually any dish prepared in a conventional oven, range or microwave can also be prepared in
the Wolf convection steam oven—with more control. Three
distinct styles compliment the look of Wolf ovens, ranges
and cooktops. It can be installed in a standard or ush inset
application.
KEY FEATURES
• Convection and steam heat with ten cooking modes for
superior control.
• Gourmet and Recipes modes for quick and convenient
meal preparation.
• Temperature probe, perforated and solid stainless
steel pans.
• Operating time, delayed start and descaling features.
CONVECTION STEAM OVENS
TRANSITIONAL
ICBCSO30TM/S/TH
PROFESSIONAL
ICBCSO30PM/S/PH
CONTEMPORARY
ICBCSO30CM/B/TH
ICBCSO30TE/S/TH
ICBCSO30PE/S/PH
wolfappliance.com | 19
Page 20
WOLF CONVECTION STEAM OVENS
Convection Steam Oven
DIMENSIONS
22 mm
454
mm
759 mm
WIDTH
65
mm
548 mm
BEHIND FRAME
SPECIFICATIONS
INTERIOR CAPACITY L
All Models 51
INTERIOR DIMENSIONS W H D
All Models 454 mm 280 mm 400 mm
446
mm
538 mm
OPEN OVEN DOOR
360
mm
20 | English
Page 21
WOLF CONVECTION STEAM OVENS
Planning Information
The convection steam oven can be installed in a standard or
ush inset application. A minimum base support of 45 kg is
required. The electrical supply for the oven must be located
in an adjacent cabinet.
Finish the edges of the opening. They may be visible when
the door is open.
For ush inset installations, a minimum 3 mm reveal is
required on all sides. To ensure consistent 3 mm reveals,
each corner of the opening must be exactly 90°.
TRIM OVERLAP
Top 5 mm
Bottom 0 mm
Sides 98 mm
ELECTRICAL
Installation must comply with all applicable electrical codes
and be properly grounded (earthed).
Locate the electrical supply as shown in the illustrations
on the following pages. A separate circuit, servicing only
this appliance is required. A ground fault circuit interrupter
(GFCI) is not recommended and may cause interruption of
operation.
Performance may be compromised if the electrical supply is
less than 220 volts.
ELECTRICAL REQUIREMENTS
Electrical Supply 220-240 VAC, 50 Hz
380-415 VAC 2N, 50 Hz
Service 3700 Watts
Power Cord 2.5 m
wolfappliance.com | 21
Page 22
SIDE
Electrical supply must be located in adjacent cabinet within .9 m of opening.
Dashed line represents profile of unit.
WOLF CONVECTION STEAM OVENS
Convection Steam Oven
STANDARD INSTALLATION
TOP VIEW
548 mm
OPENING
DEPTH
VIEW
449 mm
OPENING
HEIGHT
562 mm
OPENING WIDTH
FRONT VIEW
EE
22 | English
Page 23
SIDE
*W
NOTE: Electrical supply must be located in adjacent cabinet within .9 m of opening
Dashed line represents profile of unit.
WOLF CONVECTION STEAM OVENS
Convection Steam Oven
FLUSH INSET INSTALLATION
25 mm
FLUSH INSET
TOP VIEW
584 mm
DEPTH
FINISHED
CLEATS*
460 mm
FLUSH INSET
HEIGHT
VIEW
ill be visible and should be finished to match cabinetry.
102 mm
A
765 mm
FLUSH INSET WIDTH
FRONT VIEW
.
EE
8 mm
3 mm
wolfappliance.com | 23
Page 24
WOLF GAS COOKTOPS
Gas Cooktops
Like their built-in oven counterparts, the new generation
of Wolf gas cooktops features three new looks—Transitional, Professional, and Contemporary. New performance
enhancements make delicious results even more of a
certainty than ever. Multiple sizes, choice of knob colors,
distinctly different grates, and even a new way to integrate
with custom cabinetry—the new gas cooktops offer exceptional design exibility.
KEY FEATURES
• Dual-stacked, sealed burners for precise control and
easy cleanup.
• Flame recognition and automatic reignition for safety and
ease of use.
• True simmer setting on all burners prevents scorching.
• Illuminated, cool-to-touch knobs for user-friendly
comfort.
GAS COOKTOPS
TRANSITIONAL
ICBCG304T/S
PROFESSIONAL
ICBCG304P/S
CONTEMPORARY—COMING SOON!
ICBCG365C/S
ICBCG365T/S
ICBCG365P/S
24 | English
Page 25
WOLF GAS COOKTOPS
Gas Cooktops
762 mm TRANSITIONAL 914 mm TRANSITIONAL
533 mm
762 mm
22 mm
ALL SIDES
102 mm
914 mm
22 mm
ALL SIDES
762 mm PROFESSIONAL 914 mm PROFESSIONAL
533 mm
762 mm
102 mm
914 mm
533 mm
102 mm
533 mm
102 mm
22 mm
ALL SIDES
BURNER RATING—kW
762 mm GAS COOKTOP HIGH
Large 5.3
Medium 3.5
(2) Small 2.7
914 mm GAS COOKTOP HIGH
Large 5.3
Medium 3.5
(3) Small 2.7
22 mm
ALL SIDES
wolfappliance.com | 25
Page 26
WOLF GAS COOKTOPS
Planning Information
A minimum height clearance of 140 mm is required from the
top of the countertop to any combustible surface directly
below the cooktop.
If a cooktop is being installed above an oven, a minimum of
6 mm is required between units.
ELECTRICAL
Installation must comply with all applicable electrical codes
and be properly grounded (earthed).
ELECTRICAL REQUIREMENTS
GAS COOKTOP
Electrical Supply 220-240 V AC, 50/60 Hz
Service 10 amp dedicated circuit
Receptacle grounding-type (earthed)
GAS SUPPLY
A gas supply line of 19 mm rigid pipe must be provided
to the cooktop. If local codes permit, a certied, .9 m long,
13 mm or 19 mm ID exible metal appliance connector is
1
recommended to connect the units
/2" NPT (or ISO 7/1)
male inlet to the gas supply line.
Wolf natural gas cooktops will function up to 3124 m in
altitude without adjustment and LP gas cooktops will function up to 2621 m. If the installation exceeds these elevations, contact your authorized Wolf dealer for a high altitude
conversion kit.
GAS SUPPLY REQUIREMENTS
NATURAL GAS
Gas Supply Pressure 12.5 mb
Min Line Pressure 17.5 mb
Max Pressure to Regulator 100 mb
LP GAS
Gas Supply Pressure 25 mb
Min Line Pressure 27.4 mb
Max Pressure to Regulator 100 mb
26 | English
Page 27
WOLF GAS COOKTOPS
SIDE
NO
combus
El
Gas Cooktop
STANDARD INSTALLATION
64 mm
330 mm
457 mm
229
mm
W
WIDTH
COUNTERTOP CUT-OUT
762 mm
102 mm
89 mm
E G
254 mm
495 mm
64 mm
VIEW
TE: Shaded area above countertop indicates minimum clearance to combustible surfaces,
tible materials cannot be located within this area.
ectrical and gas supply location only applies to installations with built-in oven.
FRONT VIEW
CUT-OUT WIDTH
MODEL W
762 mm Cooktop 737 mm
914 mm Cooktop 889 mm
wolfappliance.com | 27
Page 28
WOLF COFFEE SYSTEMS
Coffee Systems
Make professional-quality brewed coffee, espresso, cappucinno, latte and more. The Wolf coffee system automatically
steams and foams the milk perfectly. Water temperature and
brew strength are adjustable. Uses either whole-bean or
ground coffee. The design pairs beautifully, either side-byside or in a tower application, with other Wolf products such
as the convection steam oven. The coffee system can be
installed in a standard or ush inset application.
KEY FEATURES
• Create perfectly brewed coffee, espresso, cappuccino,
macchiato and latte at home.
• Separate hot water dispenser for tea.
• Mounted glide system provides easy access to the unit,
no direct water line is needed.
• Milk frothing pitcher with adjustable settings, detaches
for refrigerated storage and easy cleaning.
• Built-in coffee mill with adjustable grind settings.
• Auto on, auto off and descaling features.
COFFEE SYSTEMS
610 mm MODELS
ICBEC24/B
TRANSITIONAL
762 mm M Series Trim
PROFESSIONAL
762 mm M Series Trim
CONTEMPORARY
ICBEC24/S
762 mm E Series Trim
762 mm E Series Trim
762 mm M Series Trim
28 | English
Page 29
WOLF COFFEE SYSTEMS
Coffee System
DIMENSIONS
454
mm
22 mm
W
WIDTH
394 mm
BEHIND FRAME
WIDTH
COFFEE SYSTEM W
610 mm Model 597 mm
762 mm Model 759 mm
UNIT
FULL EXTENSION
464
mm
wolfappliance.com | 29
Page 30
WOLF COFFEE SYSTEMS
Planning Information
The coffee system can be installed in a standard or ush
inset application. A minimum base support of 45 kg is
required. The sides of the cabinetry opening must be adequate to support installation of the mounting slides. Refer to
the illustrations below.
Finish the edges of the opening. They may be visible when
the door is open.
For ush inset installations, a minimum 3 mm reveal is
required on all sides. To ensure consistent 3 mm reveals,
each corner of the opening must be exactly 90°.
TRIM OVERLAP
OVERLAP 610 mm MODEL 762 mm MODEL
Top 5 mm 5 mm
Bottom 0 mm 0 mm
Sides 18 mm 98 mm
356
mm
19 mm
TYPICAL
254
mm
ELECTRICAL
Installation must comply with all applicable electrical codes
and be properly grounded (earthed).
Locate the electrical supply as shown in the illustrations
on the following pages. A separate circuit, servicing only
this appliance is required. A ground fault circuit interrupter
(GFCI) is not recommended and may cause interruption of
operation.
ELECTRICAL REQUIREMENTS
Electrical Supply 230 VAC, 50 Hz
Service 10 amp dedicated circuit
Power Cord 1.8 m
Side support.
30 | English
Slide installation.
Page 31
SIDE
NOTE: 610 mm and 762 mm models require the same opening dimensions
Dashed line represents profile of unit.
WOLF COFFEE SYSTEMS
Coffee System
STANDARD INSTALLATION
SLIDE
SUPPORT
548 mm
OPENING
TOP VIEW
DEPTH
449 mm
SLIDE
SUPPORT
VIEW
OPENING WIDTH
COFFEE SYSTEM W
610 mm Model 562 mm
OPENING
HEIGHT
762 mm Model 562 mm
E
W
OPENING WIDTH
FRONT VIEW
.
wolfappliance.com | 31
Page 32
SIDE
*W
Dashed line represents profile of unit
WOLF COFFEE SYSTEMS
Coffee System
FLUSH INSET INSTALLATION
SLIDE
SUPPORT
460 mm
FLUSH INSET
HEIGHT
SLIDE
SUPPORT
25 mm
TOP VIEW
A
FLUSH INSET WIDTH
8 mm
E
3 mm
W
584 mm
FLUSH
INSET
DEPTH
FINISHED
CLEATS*
VIEW
ill be visible and should be finished to match cabinetry.
FLUSH INSET WIDTH
COFFEE SYSTEM W A
610 mm Model 603 mm 21 mm
762 mm Model 765 mm 102 mm
32 | English
FRONT VIEW
.
Page 33
WOLF DOWNDRAFT SYSTEMS
Downdraft Ventilation
Constructed of heavy duty stainless steel, the Wolf downdraft rises from the countertop to whisk away odor and
smoke into stainless steel, mesh lters and can be lowered beneath the countertop when not in use. Downdrafts
integrate perfectly with transitional induction and electric
cooktops, gas cooktops and some integrated modules, they
can also be installed with 762 mm sealed burner rangetops.
KEY FEATURES
• Three-speed blower control with boost.
• Remote-mounted control module with LED indicators.
• Delay-off feature to automatically turn unit off.
• Stainless steel, mesh lters.
• Reversible motor box.
• Adjustable discharge.
DOWNDRAFTS
ICBDD30
ICBDD45
ICBDD36
wolfappliance.com | 33
Page 34
WOLF DOWNDRAFT SYSTEMS
Downdraft
DIMENSIONS
W
DOWNDRAFT WIDTH
356 mm
381
330
mm
A
CHIMNEY WIDTH
NOTE: Shaded line represents internal blower box with 152 mm round discharge.
mm
330
mm
730 mm
51 mm
254
mm
64 mm
172
mm
60 mm
19 mm
WIDTH
MODEL W A
ICBDD30 762 mm 673 mm
ICBDD36 914 mm 826 mm
ICBDD45 1143 mm 978 mm
34 | English
Page 35
WOLF DOWNDRAFT SYSTEMS
Planning Information
Wolf downdrafts can be installed with most Wolf cooktops,
but are not compatible with contemporary induction and
electric cooktops and the grill, steamer and fryer modules.
Downdrafts can be installed with sealed burner rangetop
model ICBSRT304. An accessory trim kit is necessary
for this installation. Contact an authorized Wolf dealer for
details.
The remote-mounted control module must be located within
3 m of the downdraft assembly and a minimum 76 mm from
the edge of the cooktop cut-out.
Internal and remote blowers are available through an authorized Wolf dealer.
Internal blowers include a 152 mm round discharge and can
be front or rear mounted. It can be discharged in any direction by rotating the blower box. Remote blowers include a
254 mm discharge and can be discharged from the front or
rear.
Consult a qualied HVAC professional for specic installation and ducting applications.
ELECTRICAL
Installation must comply with all applicable electrical codes
and be properly grounded (earthed).
Certain installations may require that the electrical supply be
placed in an adjacent cabinet.
ELECTRICAL REQUIREMENTS
DOWNDRAFTS
Electrical Supply 220-240 V AC, 50 Hz
220 V AC, 60 Hz
Service 10 amp dedicated circuit
Receptacle grounding-type (earthed)
wolfappliance.com | 35
Page 36
WOLF DOWNDRAFT SYSTEMS
Downdraft
INSTALLATION WITH COOKTOP
W
DOWNDRAFT
CUT-OUT WIDTH
68 mm
E
210 mm*
COOKTOP CUT-OUT
TOP VIEW
210
mm*
540
mm
540 mm
594 mm
E
FRONT VIEWSIDE VIEW
*152 mm back from countertop cut-out when internal blower is rear mounted.
NOTE: Internal blower 152 mm round, side, rear or bottom discharge. Remote blower 254 mm round, rear discharge.
Centerline indicates center of downdraft cut-out.
CUT-OUT WIDTH
MODEL W
ICBDD30 699 mm
ICBDD36 851 mm
ICBDD45 1003 mm
36 | English
Page 37
WOLF DOWNDRAFT SYSTEMS
Downdraft
INSTALLATION WITH SEALED BURNER RANGETOP
W
DOWNDRAFT
CUT-OUT WIDTH
68 mm
E
210 mm*
RANGETOP OPENING
TOP VIEW
483 mm
PLATFORM DEPTH
540 mm 594 mm
210
mm*
540
mm
E
FRONT VIEWSIDE VIEW
FRONT VIEWSIDE VIEW
*152 mm back from countertop cut-out when internal blower is rear mounted.
NOTE: Internal blower 152 mm round, side, rear or bottom discharge. Remote blower 254 mm round, rear discharge.
Centerline indicates center of downdraft cut-out.
CUT-OUT WIDTH
MODEL W
ICBDD30 699 mm
wolfappliance.com | 37
Page 38
WOLF DOWNDRAFT SYSTEMS
Downdraft Blower Options
BLOWER
INTERNAL ICBDD30 ICBDD36 ICBDD45
1014 m3/hr • • •
REMOTE ICBDD30 ICBDD36 ICBDD45
1014 m3/hr • • •
3
/hr • • •
2028 m
Wolf, Wolf & Design, Wolf Gourmet, W & Design and the color red as applied to knobs are registered trademarks and service marks of Wolf Appliance, Inc. Sub-Zero, Sub-Zero &
Design, Dual Refrigeration, Constant Care, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, and Ingredients are registered trademarks and service marks
of Sub-Zero, Inc. (collectively, the “Company Marks.”) All other trademarks or registered trademarks are property of their respective owners in the United States and other countries.
38 | English
Page 39
Wolf Products Limited Warranty
INTERNATIONAL PRODUCTS
FOR RESIDENTIAL USE ONLY
FULL TWO YEAR WARRANTY
For two years from the date of original installation, your Wolf Appliance product warranty covers all parts
and labor to repair or replace, under normal residential use, any part of the product that proves to be
defective in materials or workmanship. All service provided by Wolf Appliance under the above warranty
must be performed by Wolf factory certied service, unless otherwise specied by Wolf Appliance, Inc.
Service will be provided during normal business hours.
LIMITED THIRD THROUGH FIFTH YEAR WARRANTY
For ve years from the date of original installation, Wolf Appliance will repair or replace the following parts
that prove to be defective in materials or workmanship: gas burners (excluding appearance), electric
heating elements, blower motors (ventilation hoods), electronic control boards, magnetron tubes and
induction generators. The part(s) will be repaired or replaced, free of charge, with the owner paying for
all other costs including labor. All service provided by Wolf Appliance under the above warranty must be
performed by Wolf factory certied service, unless otherwise specied by Wolf Appliance, Inc. Service will
be provided during normal business hours.
wolfappliance.com | 39
Page 40
WOLF APPLIANCE, INC.
PO BOX 44848
MADISON, WI 53744 USA
WOLFAPPLIANCE.COM
IWNGDG 12/2013
Loading...