Wolf 808744 Installation

808744 - Wolf 30'' (762) Microwave Trim Kit

Installation Instructions

808662 / Rev D / May, 2009Page 1 of 2

CONTAINS: QTY DESCRIPTION

1 Ductwork, MW24 2 Screw, #8-15x1/2 Truss Hd 1 Assemblied Trim Kit 6 6-18x1 Tpg Screw Type A 2 Trim, MW24 Polycarbonate

QTY

DESCRIPTION

4 Self Tapping Screw - #8-18x1/2 1 Mtg Brkt, RT - MW 1 Mtg Brkt, LT - MW 1 Installation Instructions

INST

ALLATION PROCEDURE:

1. Locate properly grounded 3-prong receptacle 4'' (102) from right side and 4'' (102) up from bottom of microwave oven cabinet (See Cabinet Dimensions).

NOTE: You must have a properly grounded, 3prong outlet installed by a qualified electrician. Do not use a GFCI outlet, as this may cause product operation interruptions.

2. The floor of the opening should be constructed of plywood strong enough to support weight of oven and floor load (about 100lbs./ 45 kg). The floor should be level for proper operation of oven.

NOTE: Be sure to check local building code as it may require that the opening be enclosed with sides, ceiling and rear partition. The proper functioning of the oven does not require the enclosure.

*17"

(432)

20" (508)

MIN.

*1-1/4

(32)

27-1/2"

(699)

Dimensions in brackets are in millimeters unless otherwise specified

* Dimensions may vary by +/- 1/8 (.3mm)

MICROWAVE

PLATFORM

1" (2.5) MIN.

DECORATIVE CABINET RAIL 1-1/4" (32) MIN.

*1-1/4"

(32)

Cabinet Dimensions

NOTE: This Microwave trim kit is designed only for Wolf Microwave Ovens specifying 801527, 807056 or

808744 on rating label on the left side wall of oven cavity.

NOTE: Before begining remove turn table from microwave cavity.

TO AVOID ELECTRICAL SHOCK, SHUT OFF POWER BEFORE BEGINING INSTALLATION.

The Wolf Microwave Trim Kit (MWTRIM/5) is used only with the Wolf Microwave Model MW24. This model can also be installed above a Wolf SO30.

The cabinet or wall opening must be the following dimensions:

Height: 17'' (432) Width: 27-1/2'' (699) Depth: 20'' (508) min.

This kit includes metal parts that have sharp edges, handle with care to avoid possible injury.

808744 - Wolf 30'' (762) Microwave Trim Kit

Installation Instructions

808662 / Rev D / May, 2009

Mounting

Bracket Screws

Mounting Brackets

Figure 1. Mounting Brackets

Frame Assembly

Figure 3. Frame Assembly

Exhaust Duct Assembly

Exhaust Duct Mounting Screws

Figure 2. Exhaust Duct Assembly

3. Locate mounting brackets. Pre-drill pilot holes before installing screws to avoid damage to cabinet or trim kit hardware. Attach mounting brackets with supplied screws, making sure brackets do not extend beyond front surface of cabinet (See Figure 1).

4. Center exhaust duct assembly in opening. When centered correctly, its flanges will be tightly against lower front edge of opening. Secure with mounting screws (See Figure 2).

5. Place oven adjacent to wall or cabinet opening, then plug power supply cord into electrical outlet.

6. Carefully guide oven into opening. Slide oven onto exhaust duct assembly.

NOTE: Avoid pinching power cord between oven and wall.

7. Position frame assembly to be square with oven. Carefully place frame assembly on oven. Check that it is level (See Figure 3).

8. Secure frame assembly with mounting screws (See Figure 4).

9. Snap the polycarbonate trim pieces into place covering the screw holes.

Page 2 of 2

Trim Kit

Mounting

Screws

Figure 4. Trim Kit Screws