Wolf 808528, 808526, 808525, 808524, 808523 Installation

WOLF SEALED BURNER RANGETOP RISER KIT

Center Support Alignment Holes

Side Support

Front panel

Side Support

Center Support
Alignment Holes

Back Panel

801099

10-16 x 1/2”

Screw

801099

10-16 x 1/2”

Screw

730239

Finished Screws

SHOULDER

SCREWS

SHELF ASSEMBLY

KEYHOLE

SLOTS

INSTALLATION INSTRUCTIONS

Riser Kit Model Numbers:
30'' Sealed Burner Rangetop Riser:

808520 - 5'' Stainless Steel Riser Kit
808521 - 10'' Stainless Steel Riser Kit

08522 - 20'' Stainless Steel Riser

8

with Shelf Kit

36'' Sealed Burner Rangetop Rise:

808523 - 5'' Stainless Steel Riser Kit
808524 - 10'' Stainless Steel Riser Kit
808525 - 20'' Stainless Steel Riser

with Shelf Kit

48'' Sealed Burner Rangetop Riser:

808526 - 5'' Stainless Steel Riser Kit
808527 - 10'' Stainless Steel Riser Kit
808528 - 20'' Stainless Steel Riser

with Shelf Kit

Riser Kit Contents:

QTY

PART NO./DESCRIPTION

1 Center Support Bracket
1 Riser Front Panel
1 Riser Back Panel
2 Riser Supports

25 (730239) Finishing screws (#8

x 3/8'' Modified Truss Screws)
4 (801099) 10-16 x 1/2'' Screws
4 (802332) Shoulder Screws

20'' Shelf only

NOTE: Depending on which kit is
being installed, some screws may
not be used and may be discarded.

PROCEDURE

Assembling Riser:

1. Lay front panel on work surface
cosmetic side down. Remove pro­tective covering from back side of
riser front panel.

2. Attach side support legs inside of
riser front panel, using supplied
finishing screws (See Fig. 1 & 2).

3. Remove backing from double
sided tape on center support
bracket flanges (See Fig. 3).

4. Align center support bracket with
alignment holes on bottom of front
panel. Verify that center support
bracket aligns vertically prior to
adhering VHB tape to rear of
front panel.

NOTE: Proper alignment is impor­tant prior to securing tape. Firmly
press tape to back side of
front panel.

5. Slide back panel inside of front
panel mounting flanges (See Fig.

3). Align back panel mounting

holes with center support bracket
mounting hole.

6. Continue installing finishing
screws along center support
bracket and front panel
mounting flanges.

Attaching Riser Assembly to Sealed
Burner Rangetop:

Be sure to disconnect power to
sealed burner rangetop before,
installing riser assembly.

1. Verify all packing material has
been removed from riser assembly
and all packaging residues has
been cleaned from stainless
steel surface.

2. Remove island trim from sealed
burner rangetop by removing the
top screw on each side panel.

3. Slide riser side support legs inside
rangetop outer side panels until
bottom of riser assembly is flush
with side panel (See Fig. 4). Verify
that center support legs align with
mounting holes.

4. Attach riser support legs and
center support to rangetop
(See Fig. 5).

20'' Riser Shelf Installation:

Riser component parts may
have sharp edges which could
inflict serious personal injury

.

Use care when handling.

1. Once riser assembly is installed
onto rangetop, attach 4 (2 on
each side) shoulder screws in
front panel assembly.

2. Remove protective packaging
material from shelf. Align keyhole
slots on back side of shelf assem­bly with two shoulder screws on

Figure 1

right side of front panel and two
shoulder screws on left side of

ront panel assembly.

f

3. Slide shelf assembly into place
and tighten shoulder screws if
necessary (See Fig. 6).

Figure 2

Figure 3

Figure 4

Figure 5

Figure 6

808992 / Rev

/ May 2006

A