Wisenet XNV-8081Z, XNV-6081Z, XND-6081VZ, XND-6081FZ, XND-8081VZ User Manual

...

NETWORK CAMERA

User Manual

XNV-6081Z/XNV-8081Z

XND-6081VZ/XND-8081VZ

XND-6081FZ/XND-8081FZ

Network Camera

User Manual

Hanwha Techwin

Tra dema rk

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the rst time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Co., Ltd. All r ights reser ved.

Hanwha Techwin

reserves the

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.

(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from 12 Vdc, 0.7 A or PoE, 0.27 A. (XND-6081FZ/XND-6081VZ)

16. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from 12 Vdc, 0.75 A or PoE, 0.3 A.(XND-8081FZ/XND-8081VZ)

17. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from 12 Vdc, 0.8 A, 24 Vac, 0.8 A, or PoE, 0.3 A. (XNV-6081Z)

18. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from 12 Vdc 0.85 A, 24 Vac, 0.9 A, or PoE, 0.33 A.(XNV-8081Z)

19. If you use excessive force when installing the product, the camera may be damaged and malfunction. If you forcibly install the product using non-compliant tools, the product may be damaged.

20. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product.

21. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance. Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.

22. If you install/disassemble the product in a manner that has not been recommended, the production functions/ performance may not be guaranteed. Install the product by referring to “Installation & connection” in the user manual.

23. Installing or using the product in water can cause serious damage to the product.

24. Although a rapid change in temperature could cause frost inside the dome, there will be no problem with the

video.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

●● OVERVIEW

English _3

overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

The battery cannot be replaced.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE 802-3af shall be a UL Listed device with the output evaluated as a Limited Power Source as defined in UL60950-1.

Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or

heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product. yPlease wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn.

User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and human caused by

not following the instruction

 Please read this manual for the safety before using of goods and keep it in the safe place.

4_ overview

CONTENTS

outdoor vandal dome

overview

indoor vandal dome

Flush mount dome

3 Important Safety Instructions 6 Recommended PC Specifications 6 Recommended Micro SD/SDHC/SDXC

Memory Card Specifications

6 NAS recommended specs

8 What’s Included 8 At a Glance 9 Installation

17 What’s Included 17 At a Glance 18 Installation

25 What’s Included 25 At a Glance 26 Installation

network connection

and setup

web viewer

appendix

37 Connecting the Camera Directly to Local

Area Networking

37 Connecting the Camera Directly to a DHCP

Based DSL/Cable Modem

38 Buttons used in IP Installer 38 Static IP Setup 40 Dynamic IP Setup 40 Port Range Forward (Port Mapping) Setup 41 Connecting to the Camera from a Shared

Local PC

41 Connecting to the Camera from a Remote

PC via the Internet

42 Connecting to the Camera 43 Password setting 43 Login 43 Camera Web Viewer Setup

44 Specification 48 Product Overview 49 Troubleshooting 51 Open Source Announcement

●● OVERVIEW

installation & connection

32 Optional Accessories for Installation 33 Connecting with other Device

English _5

overview

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher

• RAM : 8G or higher

• Supported OS : MS Windows, Mac OS X

• Recommended browser: Google Chrome Supported browsers: MS Explorer, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OSX only)

※ Please see the appendix for detailed information on verified OS and browsers.

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 16GB to 256GB (MLC type)

• The following types of memory cards from the following manufacturers are recommended for this camera.

- Manufacturer : SanDisk, Transcend

- Product family : High endurance

NAS RECOMMENDED SPECS

• Recommended capacity : 200GB or higher is recommended.

• Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.

• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.

outdoor vandal dome

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

CAUTION: Be ware of the Rated Voltage and Polarity of the power connection.

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

WHAT’S INCLUDED

As for each sales country, accessories are not the same.

<XNV-6081Z/XNV-8081Z>

Color : Ivory

AT A GLANCE

Mount-plate

Camera-case

Camera-module

Dome-cover

Pipe-cover

DC 12 V power

connection terminal

Network

connection

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

terminal

Micro USB terminal

Reset button

Option (sold separately)

SBC-180B

(Color : Black)

8_ outdoor vandal dome

SPC-100AC

Separator strap

Audio & alarm

cable connection terminal

Micro SD card slot

AC 24 V power

connection terminal

INSTALLATION

This camera is waterproof and in compliance with the IP6K9K / IP67 / IP66 spec, but the jack connected to the external cable is not.

You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• Select an installation site that can hold at least 5 times the camera’s weight.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

• If the product is installed with excessive force, it may cause damage to the camera due to malfunction. Forcing assembly using non-compliant tools may damage the product.

2. Peel off the tape attached to the camera module.

●● OUTDOOR VANDAL DOME

Removal

1. Peel off the tape fixing the camera case.

Inserting a Micro SD Memory Card

Slide the Micro SD card into the Micro SD slot on the camera module in the direction of the arrow.

Before installing the camera, the Micro SD memory card should be inserted while the power source and the body are

separated.

Do not forcefully insert it in the reverse direction. It might damage your Micro SD memory card and your product.

When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.

When installing/removing the Micro SD memory card, make sure you put the product body on a flat ground before working on it

in order to prevent accidents due to loss or drop of any parts.

English _9

outdoor vandal dome

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.

Before removing the Micro SD memory card, in <Storage>, set the device to <Off> and press the [Apply] button and turn

the camera off.

If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or

damaged.

Installing the AC module (sold separately: SPC-100AC)

1. Install the AC module as shown in the figure.

2. Tighten the screw using the hex key.

TR20

10_ outdoor vandal dome

Installation (mount plate)

[Directly installing on wall/ceiling]

1-1. Attach the installation template on the desired surface and drill holes for screws and cables.

1-2. Fix the mount plate using appropriate screws.

1-3. Pull out necessary cables among LAN/power/audio & alarm cables through the hole in the mount plate.

[Installing using pipe]

2-1. Attach the installation template and drill holes for screws and cables.

●● OUTDOOR VANDAL DOME

2-2. Separate the pipe cover of the mount plate by pressing its sides.

English _11

outdoor vandal dome

2-3. Place the pipe on the mount plate.

2-4. Fix the mount plate using appropriate screws.

2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe.

Installation (camera case)

Use a cable bush compliant with the LAN cable to be connected.

Camera main: use a cable with the diameter of Ø5 to 6.5

Components: use a cable with the diameter of Ø5 to 8.5

[Installing LAN/power cables]

1-1. Pull off the extruded parts of the bush to be used.

1-2. Route the LAN cable through the big hole of the bush and connect to the LAN connector.

1-3. (When using the power) Route the power cable through the small hole of the bush and connect it to the

provided terminal block.

1-4. Mount the bush to the camera case.

[Installing the LAN cable] (IP66)

2-1. Pull off the extruded part of the 1-hole bush provided.

2-2. Use the cap installer to pass through the RJ45 cable.

Cap Installer

12_ outdoor vandal dome

2-3. Mount the bush to the camera case.

[Installing audio & alarm cables]

3-1. Mount the bush of the provided audio & alarm cables to the camera case.

4. Join the mount plate with the camera case.

TR20

●● OUTDOOR VANDAL DOME

English _13

outdoor vandal dome

Installing the camera module

1. Connect the LAN/power/audio & alarm cables to the camera module terminal.

2. Attach the camera module to the case.

A magnet is embedded at the bottom of the module

Take caution not to allow any foreign objects between the attaching surfaces.

* AC

Assembling the dome cover

[Directly installing on wall/ceiling]

1. Assemble the dome cover.

Make sure to firmly tighten the fastening screws so that there is no water damage issue.

TR20

3. Adjust the lens to the desired direction with reference to “Adjusting the monitoring direction for the camera” section. (page 33)

14_ outdoor vandal dome

[Using Weather cap]

1. Remove the screws from the dome cover.

2. Assemble the dome cover.

3. Mount the weather cap to the dome cover and fasten the screws.

Make sure to firmly tighten the fastening screws so that there is no water damage issue.

Using/Removing Skin cover

1. Put on the skin cover in alignment with the pipe cover.

●● OUTDOOR VANDAL DOME

TR20

2. For a camera connected with a pipe, remove the pipe cover from the skin cover first before putting it on.

TR20

English _15

outdoor vandal dome

3. To remove the skin cover, pull it while turning it clockwise as shown in the figure.

Repetitive installation and removal of the skin cover may deform the skin cover.

Installation and removal of the skin cover with excessive force may cause scratches on the surface of the product.

When pipe is connected, release it using an appropriate tool.

Outdoor installation

When you install it outside of the building, please waterproof it with waterproof butyl rubber tape (can be purchased in stores) so that water does not leak from the gap of the cable connected to the outside.

1. Connect the power, I/O, and LAN cables.

2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so

that more than half of the butyl rubber tape is overlapped.

Camera

If the cable jacket is not waterproofed properly, then it can directly cause leakage. Make sure to protect the cable with a

dense layer of taping.

Waterproof butyl tape is made of butyl rubber that can be stretched to twice its normal length.

System

16_ outdoor vandal dome

CAUTION: Be ware of the Rated Voltage and Polarity of the power connection.

CAUTION: Be ware of the

Rated Voltage and Polarity of the power connection.

CAUTION: Be ware of the Rated Voltage and Polarity of the power connection.

indoor vandal dome

WHAT’S INCLUDED

As for each sales country, accessories are not the same.

<XND-6081VZ/XND-8081VZ>

Color : Ivory

Option (sold separately)

AT A GLANCE

Pipe-cover

Mount-plate

Camera-case

Camera-module

Dome-cover

DC 12 V power

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

connection terminal

Network

connection

Micro USB terminal

Reset button

terminal

Microphone

cable connection terminal

●● INDOOR VANDAL DOME

SBC-160B

(Color : Black)

Separator strap

Audio & alarm

cable connection

Micro SD card slot

terminal

English _17

indoor vandal dome

INSTALLATION

This camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are

recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.

Precautions before installation

Ensure you read out the following instructions before installing the camera:

• Select an installation site that can hold at least 5 times the camera’s weight.

• Stuck-in or peeled-off cables can cause damage to the product or a fire.

• For safety purposes, keep anyone else away from the installation site. And put aside personal belongings from the site, just in case.

• If the product is installed with excessive force, it may cause damage to the camera due to malfunction. Forcing assembly using non-compliant tools may damage the product.

Removal

1. Peel off the tape fixing the camera case.

2. Peel off the tape attached to the camera module.

Inserting a Micro SD Memory Card

Slide the Micro SD card into the Micro SD slot on the camera module in the direction of the arrow.

18_ indoor vandal dome

Before installing the camera, the Micro SD memory card should be inserted while the power source and the body are

separated.

Do not forcefully insert it in the reverse direction. It might damage your Micro SD memory card and your product.

When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.

When installing/removing the Micro SD memory card, make sure you put the product body on a flat ground before working on it

in order to prevent accidents due to loss or drop of any parts.

Removing a Micro SD Memory Card

Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.

Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.

Before removing the Micro SD memory card, in <Storage>, set the device to <Off> and press the [Apply] button and turn

the camera off.

If you turn off the camera or remove the Micro SD memory card that contains data from the product, the data may be lost or

damaged.

Installation (mount plate)

[Directly installing on wall/ceiling]

1-1. Attach the installation template on the desired surface and drill holes for screws and cables.

●● INDOOR VANDAL DOME

1-2. Fix the mount plate using appropriate screws.

1-3. Pull out necessary cables among LAN/power/audio & alarm cables through the hole in the mount plate.

English _19

+ 43 hidden pages