Wisenet XNP-9300RW, XNP-8300RW, XNP-6400RW User Manual

NETWORK CAMERA

User Manual

XNP-9300RW XNP-8300RW XNP-6400RW

Network Camera

User Manual

Hanwha Techwin

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility. right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the rst time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information theft. Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Co., Ltd. All r ights reser ved.

Hanwha Techwin

reserves the

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.

(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.)

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated from PoE(55 Vdc), 0.77 A.

16. This product is intended to be supplied by isolation power.

17. If you use excessive force when installing the product, the camera may be damaged and malfunction.

If you forcibly install the product using non-compliant tools, the product may be damaged.

18. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product.

19. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance. Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.

20. If you install/disassemble the product in a manner that has not been recommended, the production functions/ performance may not be guaranteed. Install the product by referring to “Installation & connection” in the user manual.

21. Installing or using the product in water can cause serious damage to the product.

22. If your product works normal, the degree of preset precision is 0.1˚. In the case of reboot due to outage,

firmware upgrade, etc., its tolerance might have to be adjusted after checking for any changes in Preset setup.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance with the installation instructions.

Pan/Tilt/Zoom motors and slip ring are warrantied for one year under continuous operation.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

English _3

●● OVERVIEW

overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

The battery cannot be replaced.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved agency is employed.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

ATTENTION

IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE TYPE INCORRECT. METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.

CAUTION

These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

Please use the input power with just one camera and other devices must not be connected.

The ITE is to be connected only to PoE networks without routing to the outside plant.

The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE

802.3bt shall be a UL Listed device with the output evaluated as a Limited Power Source

as defined in UL60950-1 or PS2 as defined in UL62368-1.

Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102. As such, associated Ethernet wiring shall be limited to inside the building.

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface. yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or

heavy cold area. yDo not place this apparatus near conductive material. yDo not attempt to service this apparatus yourself. yDo not place a glass of water on the product. yDo not install near any magnetic sources. yDo not block any ventilation openings. yDo not place heavy items on the product. yPlease wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn. yWhen connecting the HPoE injector to the external Internet, use either one of network cable

port (LAN) or fiber optic port (SFP) but not both.

User’s Manual is a guidance book for how to use the products. The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages yNotice : If there’s any possibility to occur any damages for the goods and human caused by

not following the instruction

 Please read this manual for the safety before using of goods and keep it in the safe place. We do not guarantee the quality of third-party products (e.g. lenses, accessories) that you

separately purchase.

WARNING

To Prevent damage which may caused by IR LED, don't stare at operating lamp.

For below models only.

XNP-9300RW

XNP-8300RW

XNP-6400RW

Risk Group 1

4_ overview

WARNING IR emitted from this product.

Do not stare at operating lamp.

Product tested against IEC 62471

CONTENTS

OVERVIEW

INSTALLATION & CONNECTION

NETWORK CONNECTION AND

SETUP

3 Important Safety Instructions 6 Recommended PC Specifications 6 Recommended Micro SD/SDHC/SDXC

Memory Card Specifications

6 NAS recommended specs 7 What’s Included 7 Optional Accessories for Installation 8 At a Glance

10 Installation 17 Powering and networking

18 Connecting the Camera Directly to Local

Area Networking

18 Connecting the Camera Directly to a DHCP

Based DSL/Cable Modem

19 Using Device Manager 19 Automatically searching camera 19 Configuring IP address 20 Manually registering camera 20 Automatically configuring IP 21 Port Range Forward (Port Mapping) Setup 22 Connecting to the Camera from a Shared

Local PC

22 Connecting to the Camera from a Remote

PC via the Internet

WEB VIEWER

APPENDIX

23 Connecting to the Camera 24 Password setting 24 Login 24 Camera Web Viewer Setup

25 Troubleshooting

●● OVERVIEW

English _5

overview

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher

• RAM : 8G or higher

• Supported OS : MS Windows 8.1, 10, Mac OS X 10.13

• Recommended browser: Google Chrome

• Supported browsers: MS Explore11, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OSX only)

• VGA : PCIe 256MB GDDR3 video graphics card or higher

※

Some functions may be restricted even in supported browsers.

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 16GB to 1TB (MLC type required)

• Recommended Manufacturers : SanDisk, Transcend

• Product Type : High endurance

• The compatibility varies depending on the card manufacturers and types.

Micro SD card can support up to 1 TB if two slots are used. Each slot supports up to 512 GB, and one slot cannot support

1 TB by itself.

NAS RECOMMENDED SPECS

• Recommended capacity : 200GB or higher is recommended.

• For this camera, you are recommended to use a NAS with the following manufacturer’s specs. Recommended products : QNAP NAS, Synology NAS

6_ overview

WHAT’S INCLUDED

CAUTION: Be ware of the Rated Voltage and Polarity

of the power connection.

Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description

OPTIONAL ACCESSORIES FOR INSTALLATION

You can purchase appropriate optional accessories available.

●● OVERVIEW

Main Body

Quick Guide

(Optional)

SFP

LAN PoE

0Link

POWER

HPoE injector 1 Connects power supply and network

Power cord 1 Connects to HPoE injector

Wall & Pole Mount Corner Mount Hanging Mount

* This mount can be used after being

attached to hanging mount

SBP-300LMW (Parapet Mount)

SBP-300CMW (Ceiling Mount)

SBP-156WMW SBP-156KMW SBP-156HMW

SBP-300WMW (Wall Mount)

SBP-300WMW1 (Wall Mount)

SBP-300PMW (Pole Mount)

Cap Installer 1 Used to connect the network cable

Bushing clip 1

Cable Bushing

Used as a means of preventing cable bushing from

being separated or falling apart from the hole.

Extra cable bushing for network cable installation.

SBP-300KMW (Corner Mount)

English _7

overview

AT A GLANCE

Appearance

Main cover

Windshield wiper

Shield cover

Micro SD Card cover

Item Description

Protects the internal PTZ mechanism from the direct sunlight, rain or external impact.

Used for wiping off raindrops or snow dripping on the window.

Do not adjust the wiper manually by hand. After power is turned on, booting will be

completed and the wiper will move to its default position.

Shield cover for the lens and unit protection.

Covers micro SD card slots and the Reset button. You can open it using a Torx driver.

Inside

b c

Item Description

IR LED These infrared LED’s are controlled by the illumination sensor.

Lens Lens for the camera.

Illumination Sensor Detects incoming light to control the IR LED.

The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

Reset button

enabled. If there is no DHCP server in the network, you must run the Device Manager program to change the basic network settings such as IP address, Subnet mask, Gateway, etc., before you can connect to the network.

8_ overview

Micro SD Card slot Compartment for the Micro SD card.

Mounting surface

Item Description

Cable bushing A waterproof rubber cap, which allows a network cable to go through it.

Safety wire hook

HPoE port

Hang this hook on the safety wire of the mount when installing this product to prevent it from falling.

A port that connects to the HPoE injector and network cable for power and network connection.

●● OVERVIEW

English _9

+ 18 hidden pages