Wisenet XNF-9010RV, XNF-9010RVM User Manual

NETWORK CAMERA

User Manual

XNF-9010RV/XNF-9010RVM

Network Camera

User Manual

Copyright

Hanwha Techwin

©2020

Trademark

Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their
respective company.

Restriction

Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without
formal authorization.

Disclaimer

Hanwha Techwin

provided. Use of this document and the subsequent results shall be entirely on the user’s own responsibility.
right to change the contents of this document without prior notice.

Design and specications are subject to change without prior notice.

The initial administrator ID is “admin” and the password should be set when logging in for the rst time.

Please change your password every three months to safely protect personal information and to prevent the damage of the information
theft.
Please, take note that it’s a user’s responsibility for the security and any other problems caused by mismanaging a password.

makes the best to verify the integrity and correctness of the contents in this document, but no formal guarantee shall be

Co., Ltd. All r ights reser ved.

Hanwha Techwin

reserves the

overview

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth.

(Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents
as they may deform or cause damage to the product.)

7. Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and
the point where they exit from the apparatus.

11. Only use attachments/ accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,

or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus

has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.

15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or “LPS” and rated
from 12 Vdc, 1.1 A or PoE, 0.35 A.

16. This product is intended to be supplied by isolation power.

17. If you use excessive force when installing the product, the camera may be damaged and malfunction.

If you forcibly install the product using non-compliant tools, the product may be damaged.

18. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As
edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or
near the kitchen table.
This may cause damage to the product.

19. When installing the product, be careful not to allow the surface of the product to be stained with chemical
substance.
Some chemical solvents such as cleaner or adhesives may cause serious damage to the product’s surface.

20. If you install/disassemble the product in a manner that has not been recommended, the production functions/
performance may not be guaranteed.
Install the product by referring to “Installation & connection” in the user manual.

21. Installing or using the product in water can cause serious damage to the product.

22. Although a rapid change in temperature could cause frost inside the dome, there will be no problem with the

video.

23. This device has been verified using STP cable. The use of appropriate GND grounding and STP cable
is recommended to effectively protect your product and property from transient voltage, thunderstroke,
communication interruption.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH THE
VENTILATION GRILLS OR OTHER OPENNINGS ON THE EQUIPMENT.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed on the apparatus.

To prevent injury, this apparatus must be securely attached to the Wall/ceiling in accordance
with the installation instructions.

CAUTION

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION

: TO REDUCE THE RISK OF ELECTRIC SHOCK.

DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

EXPLANATION OF GRAPHICAL SYMBOLS

The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of
electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance (servicing) instructions in
the literature accompanying the product.

English _3

●● OVERVIEW

overview

Class construction

An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a
protective earthing connection.

Battery

Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as
sunshine, fire or the like.

The battery cannot be replaced.

Disconnection Device

Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in
your location.

When used outside of the U.S., it may be used HAR code with fittings of an approved
agency is employed.

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

ATTENTION

IL Y A RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACÉE PAR UNE BATTERIE DE
TYPE INCORRECT.
METTRE AU REBUT LES BATTERIES USAGÉES CONFORMÉMENT AUX INSTRUCTIONS.

CAUTION

These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock do not perform any servicing other than that contained in
the operating instructions unless you are qualified to do so.

The Test Monitor Out port of the product is provided for easier installation, and is not
recommended for monitoring purposes.

Please use the input power with just one camera and other devices must not be connected.
Before connecting the Power Terminal Block, you need to unplug the power plug from the

outlet first.

The ITE is to be connected only to PoE networks without routing to the outside plant.

The wired LAN hub providing power over the Ethernet (PoE) in accordance with IEEE

802.3.af shall be a UL Listed device with the output evaluated as a Limited Power Source
as defined in UL60950-1 or PS2 as defined in UL62368-1.

Unit is intended for installation in a Network Environment 0 as defined in IEC TR 62102.
As such, associated Ethernet wiring shall be limited to inside the building.

Please read the following recommended safety precautions carefully.

yDo not place this apparatus on an uneven surface.
yDo not install on a surface where it is exposed to direct sunlight, near heating equipment or

heavy cold area.
yDo not place this apparatus near conductive material.
yDo not attempt to service this apparatus yourself.
yDo not place a glass of water on the product.
yDo not install near any magnetic sources.
yDo not block any ventilation openings.
yDo not place heavy items on the product.
yPlease wear protective gloves when installing/removing the camera.

The high temperature of the product surface may cause a burn.

User’s Manual is a guidance book for how to use the products.
The meaning of the symbols are shown below.

yReference : In case of providing information for helping of product’s usages
yNotice : If there’s any possibility to occur any damages for the goods and human caused by

not following the instruction

 Please read this manual for the safety before using of goods and keep it in the safe place.

We do not guarantee the quality of third-party products (e.g. lenses, accessories) that you
separately purchase.

WARNING

To Prevent damage which may caused by IR LED, don't stare at operating lamp.

For below models only.

XNF-9010RV

XNF-9010RVM

Risk Group 1

WARNING IR emitted from this product.

Do not stare at operating lamp.

Product tested against IEC 62471

4_ overview

CONTENTS

OVERVIEW

3

INSTALLATION & CONNECTION

10

NETWORK CONNECTION AND

SETUP

18

3 Important Safety Instructions
6 Recommended PC Specifications
6 Recommended Micro SD/SDHC/SDXC

Memory Card Specifications

6 NAS recommended specs
7 What’s Included
8 Optional Accessories for Installation
8 At a Glance

10 Installation
15 Connecting with other Device

18 Connecting the Camera Directly to Local

Area Networking

18 Connecting the Camera Directly to a DHCP

Based DSL/Cable Modem

19 Using Device Manager
19 Automatically searching camera
19 Configuring IP address
20 Manually registering camera
20 Automatically configuring IP
21 Port Range Forward (Port Mapping) Setup
22 Connecting to the Camera from a Shared

Local PC

22 Connecting to the Camera from a Remote

PC via the Internet

WEB VIEWER

23

APPENDIX

25

23 Connecting to the Camera
24 Password setting
24 Login
24 Camera Web Viewer Setup

25 Troubleshooting

●● OVERVIEW

English _5

overview

RECOMMENDED PC SPECIFICATIONS

• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher

• RAM : 8G or higher

• Recommended browser: Chrome

• Supported browsers: Chrome, Safari, Firefox, MS Edge(chromium based)

• Supported OS : Windows, Mac, Linux, Android, iOS, Chrome

• Verification environment

- Windows 10: Google Chrome version 80 or later, Firefox version 72 or later, MS Edge version 83 or later

- Mac 10.13/14: Safari version 11.0.1 or later



The video play performance of the web viewer depends on the performance of the user’s CPU and GPU.

RECOMMENDED MICRO SD/SDHC/SDXC MEMORY CARD SPECIFICATIONS

• Recommended capacity : 16GB to 256GB (MLC type required)

• Recommended Manufacturers : SanDisk, Transcend

• Product Type : High endurance

• The compatibility varies depending on the card manufacturers and types.

Micro SD card can support up to 512 GB if two slots are used. Each slot supports up to 256 GB, and one slot cannot support

`

J

512 GB by itself.

NAS RECOMMENDED SPECS

• Recommended capacity : 200GB or higher is recommended.

• For this camera, you are recommended to use a NAS with the following manufacturer’s specs.
Recommended products : QNAP NAS, Synology NAS

6_ overview

WHAT’S INCLUDED

CAUTION: Be ware of the
Rated Voltage and Polarity

of the power connection.

CAUTION: Be ware of the
Rated Voltage and Polarity

of the power connection.

Please check if your camera and accessories are all included in the product package.
(As for each sales country, accessories are not the same.)

Appearance Item Name Quantity Description Model Name

Camera 1

XNF-9010RV/

XNF-9010RVM

Appearance Item Name Quantity Description Model Name

Cable bushing 1

Extra cable bushing for network

cable installation.

XNF-9010RV/

XNF-9010RVM

●● OVERVIEW

Quick Guide

(Optional)

Cable for the testing monitor 1

MOUNTING HOLE (4X)

HORIZONTAL LINE

160mm (6.30”)

CABLE HOLE (2X)

CABLE HOLE

27mm (1.06”)

Template 1 Product installation guide

1

Used to test the camera connection

to a portable display device

Torx L wrench 1 To remove/fix the top cover

Audio/Alarm/Power cable 1

Cap Installer 1

Used for audio, alarm, DC 12V power

supply

Used to connect the RJ45 network

cable

XNF-9010RV/

XNF-9010RVM

XNF-9010RV/

XNF-9010RVM

XNF-9010RV/

XNF-9010RVM

XNF-9010RV/

XNF-9010RVM

XNF-9010RV/

XNF-9010RVM

XNF-9010RV/

XNF-9010RVM

M12 Female connector cable 1

network when coupled with an M12

male connector.

XNF-9010RVM

Used to supply power and connect

English _7

overview

OPTIONAL ACCESSORIES FOR INSTALLATION

You can purchase appropriate optional accessories available.

Model name Hanging Mount All

XNF-9010RV/

XNF-9010RVM

SBP-167HMW

SBP-300LMW (Parapet Mount)

SBP-300CMW (Ceiling Mount)

SBP-300WMW (Wall Mount)

SBP-300WMW1 (Wall Mount)

SBP-300NBW (Instalation Box)

SBP-300NBW (Wall Mount Base)

SBP-300PMW (Pole Mount)

SBP-300KMW (Corner Mount)

AT A GLANCE

Appearance

a

b

c

d

8_ overview

Mount plate

a

Camera body

b

Top cover

c

Microphone hole

d

Item Description

Plate that fixes the camera when mounting it to the ceiling or attaching it to a separately
sold mount.

Body part where the camera lens and connection terminals are included.

Case cover used to protect the lens and the main unit.

A microphone hole to use the internal microphone.

Inside

Item Description

b ca

d fe g

Item Description

Focus Control Button

a

MICRO USB port

b

Reset Button

c

Press this button for automatic focus control.

Port to connect the WiFi dongle.
You can check the installation video through the applications installed in the smartphone.
Refer to “Connecting WiFi” on page 15.

Wifi dongle and OTG adapter are sold separately.

`

The button restores all camera settings to the factory default.
Press and hold for about 5 seconds to reboot the system.

If you reset the camera, the network settings will be adjusted so that DHCP can be

J

enabled. If there is no DHCP server in the network, you must run the Device Manager
program to change the basic network settings such as IP address, Subnet mask,
Gateway, etc., before you can connect to the network.

h ji

Network Port

g

IR LED

h

Fisheye lens

i

Illumination Sensor

j

Micro SD card slot

k

Microphone hole

l

Used to connect the PoE or Ethernet cable for network connection.

These infrared LED’s are controlled by the illumination sensor.

This lens has 360˚ vision and it can record video panoramically.

Detects incoming light to control the IR LED.

Compartment for the Micro SD card.

The MIC is built into the camera.

●● OVERVIEW

lk

Test monitor out port

d

Alarm I/O / Power port

e

(DC 12V)

Audio cable port

f

Output port for test monitoring the video output. Use the test monitor cable to connect to a
mobile display and check the test video.

Connects the large port part of the audio/alarm/power cable for the connection of Alarm I/O
and power.

Connects the small port part of the audio/alarm/power cable for the connection of speaker
and microphone.

English _9