Wisco 630-1 User Manual

DELIWRAPPER

MODEL 630

FEATURES:

- INCLUDESADAPTER DISC FOR 10”-12” PIZZAS.

- High watt density heating element shrink wraps pizza in seconds.

-Thermostatically controlled heating element provides controlled heat for continuous or intermittent operation.

- (3) thumb screws remove basic protection shroud for cleaning. Heat shroud and stainless steel clean-out tray add to ease of maintenance and cleanability.

- Heat shroud reduces temperature to prevent film sticking and provides extra measure of safety to prevent burns.

-Adjustable pedestal accommodates various sizes of product for shrink wrapping.

AVAILABLE ACCESSORIES:

ELECTRICAL:

- 120 volts,12.5 amps,1150 watts

- Best when operated on an individual branch circuit

- 6’ power cord length

DIMENSIONS: (does not reflect shipping dimensions)

- 7”H x 12”W x 12”D with adjustable supporting surface.

- 14” diameter protective shield

SHIPPING WEIGHT:

Approx.13 lbs.

- MODEL 650:2 tier dispenser (photo shown)

- MODEL 650-1: Single tier dispenser

- 14” - 16” pizza Adapter Disc ( #0016239)

- 6” - 8” pizzaAdapter Disc ( #0016240)

- SHRINK FILM:

FP140022 02/10

P.O.BOX #10 OREGON,WI 53575 PHONE:608-835-3106 FAX:608-835-8273 www.thepizzaoven.biz

Part Sheet Recommended # of Sheets

Number Size For: Per Roll 0017011 16 x 16 8” Pizza 1100 0017018 18 x 18 10” Pizza 600 0017008 20 x 20 12” Pizza 500 0017010 22 x 22 14” Pizza 500 0017009 24 x 24 16” Pizza 500

LIMITED WARRANTY:

WiscoIndustries, Inc. expressly warrants the product willbe freefrom defects in workmanship andmaterials for a period of 1 year from the date of shipment. WISCO DISCLAIMSAND EXCLUDES ANYANDALL OTHER EXPRESS OR IMPLIED WARRANTIES, INCLUDINGWITHOUT LIMITATION, ANY AND ALL WARRANTIES OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE.

Buyer agrees that its SOLE ANDEXCLUSIVE REM EDY against Wisco and Wisco’s SOLEAND EXCLUSIVE LIABILITY arising out of any defect or nonconformity in the productshall be replacement/exchange of such nonconforming countertopfood service equipment at Wisco’s expense. Nocountertop f ood service equipmentshall be returned without Wisco’s consent. IT ISAGREED THATWISCO’S MAXIMUM LIABILITYSHALL NOT INANY CASE EXCEEDTHE SALE PRICE FOR THE COUNTERTOP EQUIPMENT CLAIMED TO BEDEFECTIVE OR NONCONFORMING.

MODEL 630-1 DELIWRAP INSTRUCTIONS

UNPACKING AND ASSEMBLY:

- Remove Deli-Wrap from carton

- Remove cardboard from bottom of unit and heating element.

(CAUTION: DO NOT PLUG UNIT IN WITH CARDBOARD HEATING ELEMENT SUPPORT IN PLACE).

- Screw threaded rod into disc.

-Thread wing nut on the opposite end of rod so the wings of the nut face jam nut.

-Thread disc and rod assembly into grille assembly until the height is approx.4-1/2” to 5”.

- Lock wing nut against grille assembly. (The 4-1/2” to 5” dimension given is only a starting place. Due to the differences in wrapping mediums,you may have to adjust your pedestal height to attain best wrapping results.)

- Place grille with pedestal assembly on the brackets riveted to the inner shroud.

- Clean out tray can then be put in place. Clean out tray should be centered between shroud support brackets and resting on the base of the unit.

*You are now ready to plug the unit into a 15amp 115 volt outlet.

CAUTION: THE CARDBOARD SUPPORT MUST BE REMOVED FROM THE HEATING ELEMENT BEFORE ENERGIZING UNIT.

OPERATION:

Plug unit in and turn the thermostat switch to the Medium to High position. Pre-heat DeliWrap machine for approximately 3 minutes.

Place the product being wrapped on the center of the pedestal,immediately tear off a sheet of shrink wrap material from the Deli-Wrap dispenser and place over product paying special attention to the symmetry. Best results will be achieved if the wrapping material is evenly laid over the product.

In approximately 10 to 20 seconds your product will be enveloped and sealed. Remove from pedestal and allow to cool. CAUTION: DO NOT LEAVE PRODUCT UNATTENDED WHEN WRAPPING.

MAINTENANCE:

Unplug unit before any cleaning,servicing or maintenance is performed. The outer shroud,inner shroud,clean out tray and grille assembly with pedestal can be removed

for daily cleaning.

IMMERSE BASE ASSEMBLY OF THE DELI WRAP IN WATER.

CAUTION: ALLOW UNIT TO COOL BEFORE REMOVING ANY PARTS. DO NOT

Replace all parts after cleaning.

The Deli-Wrap has been tested and approved by Underwriters Laboratories,to be a safe and durable product when used and maintained in the manner in which it was intended.