Amplified Low Profile
Indoor Television Antenna
Model SS-3000
FRONT OF ANTENNA
U.S. Patent No. 7,113,147
POINT TOWARD SIGNAL
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000
319/754-0600 • FAX 319/754-0787 • www.winegard.com
Printed in U.S.A. ©2005 Winegard Company Rev4 8/12 2452064
About Your SS-3000 Antenna Installation
Thank you for choosing the low profile SS-3000 antenna. Winegard antennas
are designed to deliver sharp, clear, high definition signal reception. At
Winegard, our engineering department is dedicated to designing antennas
that embrace both the latest technology and the aesthetics of any viewing
environment. The SS-3000 installs in minutes; it’s easy to use and simple to
adjust. Before installing your antenna, please remove all parts from the box,
and read the manual carefully.
Reflector
Antenna Base
(4) Clips
6’ Mini Coax Downlead
An additional piece of RG6/U coax cable
can be used to extend the cable length
from the antenna to the Power Injector up
to 50’. Use FS-8100 cable to cable connector to combine cables.
Collar Clamp
Antenna
ANT.
Power IN
LED
FRONT OF ANTENNA
POINT TOWARD
SIGNAL
Power
Injector
TV
Coax Cable to Digital
TV, Digital Converter
Box, Distribution Amp
or Splitter
Attaching the clips to the Reflector
1. Lay the reflector flat on the table.
2. Grip the reflector with your thumb and index finger, and bend the
reflector’s top and bottom edges towards you. (See Fig. 2, 3.)
3. With your other hand, grasp the clip, and attach it to the reflector at the
two notches.
4. Repeat steps 2 and 3 for all four clips.
Fig. 2
Notch
Notch
Fig. 3
6’ Standard
AC Adaptor
(Supplied)
Coax Cable
(Supplied)
Installation
1. Find clamp collar half with two holes. Attach to antenna with the two long
screws. Do not tighten at this time.
2 3
Installation Installation
Attaching the Reflector to the Antenna
1. Starting from the right side, slide the clip attached to the reflector diagonally
into the notch at the back of the antenna. (See Fig. 4, 5.)
2. Once the clip is pushed in, slide it to the side so that it forms a 90 degree
angle to the antenna’s edge. (See Fig. 6.)
3. Repeat steps 1 and 2 for all four clips.
Fig. 5
Fig. 4
Attaching the Antenna with reflector to the Base
1. Route the 6’ mini coax cable through the base, and screw it securely to
the antenna.
2. Slide the antenna with reflector onto the base.
3. Using a screwdriver, slightly tighten the two screws, to secure the antenna
to the base. (See Fig. 7.)
Fig. 7
Making Connections
1. Connect the mini coax cable attached to the antenna to the connection on
the power injector labeled “Antenna”.
2. Connect the 2’ coax cable from the connection on the power injector
labeled “TV” to your HDTV or set-up box.
3. Connect the 6’ standard coax cable from the connection on the power
injector labeled “Power” to the AC adapter.
4. Plug in the AC adapter to a standard AC outlet.
Fig. 8
AC Adaptor
(Supplied)
Fig. 6
6’ Mini Coax Downlead From Antenna
ANT.
Power IN
LED
6’ Standard
Coax Cable
(Supplied)
Power
Injector
TV
Coax Cable to Digital
TV, Digital Converter
Box, Distribution Amp
or Splitter
Attaching Rubber Feet to the Base
Remove the protective adhesive
strip from the four rubber feet and
apply them to the bottom of the
antenna base.
Fig. 9
Feet
4 5
Operating Your SS-3000 Troubleshooting
Locating your SS-3000 Antenna
Your antenna is a precision instrument and should be placed in a location that
is best for receiving TV signals.
Your antenna can be placed on top of any TV for ease of adjustment.
Operating your SS-3000 Antenna
Positioning the antenna properly will give you optimal digital television (DTV)
reception, especially in areas of high multipath. In such areas, repositioning
the antenna a few inches could mean the difference between an excellent DTV
stream or picture loss.
First, point the antenna towards a window in the direction of your TV stations
(if possible). If this fails to give you a solid picture, slowly rotate the antenna in
small increments up to 360 degrees until you receive a picture. The antenna
was designed to pick up direct and reflected signals from interior walls. Keep
in mind that the best reflected signal may be behind the antenna or off a
building outside.
NOTE: You must do a “Rescan” of the TV channels each time the antenna is
moved. It is best to utilize the Signal Strength Meter of your set-top box or an
HDTV television with built-in tuner to optimize the position of the antenna.
You can use the following Web tool to find where the broadcast towers are
located from your home address:
1. Go to www.antennaweb.org, and click “Choose an Antenna”.
2. Enter your home address, and click “Submit.”
3. Click “View Street Level Map” to see which direction you should point
your antenna.
Please Note:
1. Do not place your antenna near large metal objects or appliances that could
create interference.
2. Do not lift your antenna by its receiving elements or place objects on them.
3. Late model televisions have on-screen menu controls for viewing VHF/UHF
“Off-Air” or cable broadcasts. Please ensure that this menu control is at the
proper “Off-Air” position.
No picture, or the tuner is displaying no “signal.”
1. Make sure the antenna is connected to the correct “Antenna in” input on the
set-top box or TV.
2. Rotate the antenna around the room to find the best reflected signal,
keeping in mind that the best reflected signal may be behind the antenna.
(See page 6 for directions on how to use the web to locate the broadcast
tower location. Rotate the antenna base up to 360° until you receive the
best signal possible).
3. For houses with aluminum siding/insulation or stucco, place the antenna
near a window to minimize interference.
Indoor Reception
CHANNEL ANALOG DIGITAL
2–6 0–10 0–15
7–13 0–20 0–25
14–69 0–25 0–30
Frequently Asked Questions
Q. What do I need to get HDTV?
A. A High Definition television with built-in or set-top HD receiver.
Q. Why do I need an antenna?
A. This antenna will get you local high definition broadcast channels proving
you live within 30 miles of the broadcast tower and that there are no
obstacles between you and the broadcast tower that could interfere with
reception (see note below).
Q. Can I use this antenna in a basement?
A. It is not recommended. Broadcast signals cannot penetrate into basements
due to their lower elevation.
Q. How can I get channels above channel 13?
A. Tuners have both cable and antenna modes. Access the proper on screen
TV menu and switch from Cable/CATV mode to ANT/AIR mode to receive
these channels.
Please Note:
Other variables, which are not related to antenna performance, can affect your
reception. These include distance from the source transmitting the desired
station, man-made and natural conditions.
Example: Obstacles such as buildings between the transmitting source and
your antenna can affect your reception.
6 7
Performance Specifications
Channels: VHF: 2–13
UHF: 14–69
Dimensions: 5”H x 26-3/4”W x 4-1/4”D
Amplifier Gain: VHF/UHF: 7–10 dB average
90 DAY LIMITED WARRANTY
Winegard Company warrants this Winegard product against any defects in materials
or workmanship within 90 (ninety) days from date of purchase. No warranty claim will
be honored unless at the time the claim is made, you present proof of purchase to an
authorized Winegard dealer (if unknown, please contact Winegard Company, 3000
Kirkwood Street, Burlington, IA 52601-2000, Telephone 800-288-8094).
Winegard Company (at its option) will either repair or replace the defective product at
no charge to you. This warranty covers parts, but does not cover any costs incurred in
removal, shipping or reinstallation of the product. This limited warranty does not apply
if the product is damaged, deteriorates, malfunctions or fails from: misuse, improper
installation, abuse, neglect, accident, tampering, modification of the product as originally
manufactured by Winegard, usage not in accordance with product instructions or acts
of nature such as damage caused by wind, lightning, ice or corrosive environments
such as salt spray and acid rain.
The 90 Day Warranty is provided on the condition that the equipment is properly
delivered with all handling and freight charges prepaid to your Winegard dealer for
return to our factory for repair or replacement. Winegard dealers will arrange for the
replacement or repair and return to you without charge the product which failed due
to defective material or workmanship.
WINEGARD COMPANY WILL NOT ASSUME ANY LIABILITIES FOR ANY OTHER
WARRANTIES, EXPRESS OR IMPLIED, MADE BY ANY OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY
ARE LIMITED TO THE 90-DAY PERIOD OF THIS WARRANTY.
The foregoing shall be the sole and exclusive remedy of any person, whether in
contract, tort or otherwise, and Winegard shall not be liable for incidental or consequential
damage or commercial loss, or from any other loss or damage except as set forth above.
Some states do not allow limitations on how long an implied warranty lasts, or the
exclusion of limitation of incidental or consequential damages, so the above limitations
or exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
Winegard Company • 3000 Kirkwood Street • Burlington, IA 52601 • 319/754-0600 • Fax 319/754-0787
www.winegard.com • Printed in U.S.A. ©2005 Winegard Company Rev4 8/12 2452064
Loading...