Winegard FL-5000 User Manual

Model FL-5000

For help, email [e-mail] or call 1-800-788-4417.

DO NOT RETURN ANTENNA TO PLACE OF PURCHASE.

Specifications

• For indoor use only

• Range of 25 miles (performance may

vary based on terrain and obstructions)

• For high VHF & UHF channels

• Recommended for use with one TV

• Small, compact size

• Includes 3M™ Command™

Brand Strips

• No assembly required

• Model FL-5000

Setup

1

Connect the mini coax cable
to the “Antenna In” coax port
on the TV.

Run a channel scan. (For a listing

2

of likely channels available in your area, go
online to www.winegard.com/localchannels.)

3

If not satisfied with the number of channels found, try re-positioning the
antenna. Moving the antenna three feet in one direction is often enough
to change the reception. Then, re-run a channel scan.

2452248

Once the best location has been determined, secure the antenna with the
provided command strips, which can be placed on any part of the antenna.

If more coaxial cable is needed to mount the antenna in the desired location,
connect the coaxial cable to a female-to-female barrel connector (Winegard
model FS-8100), sold separately), and attach additional coaxial cable.

Do not paint the FlatWave antenna. This could block signal and void your
warranty. Note that the antenna is not meant for use in an attic.

Tips for Maximizing Reception

The FlatWave antenna is small enough to hide behind a TV or picture frame.

Mount the antenna on a window that faces the broadcast tower of stations
that you want to receive. The sides of the antenna have blind spots, so the
antenna may not “see” enough signal from the broadcast tower if the sides
of the antenna face the tower.

If the antenna is mounted so that it hangs vertically, the coax cable should run
from the top or bottom of the antenna. If the antenna is mounted so that it lies
flat (e.g. on a table), the coax cable should point toward the signal.

The coax cable is running from the side of the antenna instead of the top or
bottom of the antenna. Try re-positioning the antenna so that the coax cable
runs from the top or bottom of the antenna, and run a new channel scan.

The antenna may pick up signal when mounted near electronics, or
electronics, including the television itself, may reflect the signal from the
broadcast tower. If so, try mounting the antenna higher on the wall, and run a
new channel scan. The higher the antenna, the better signal you will receive.

Questions & Answers

Questions & Answers, Cont.

Q. What channels can the FlatWave antenna receive?

A. The FlatWave antenna can receive programming from all of the major local

broadcast networks (e.g. ABC, CBS, FOX, NBC, PBS) plus additional networks
(Qubo, ION, The CW, This TV, MyNetworkTV, Azteca, Telefutura, Univision, and
Telemundo). The FlatWave antenna can also receive local news, weather and
educational programs that satellite and cable don’t offer.

Q. How can I find out what channels are broadcast in my area?

A. Check out www.winegard.com/localchannels. On this site, you can enter

your address and get a listing of likely channels available in your area.

Q. How many channels will I receive with the FlatWave antenna?

A. The number of channels will vary from location to location. Generally

speaking, if you live in or near a metropolitan area you will receive more
channels than if you live outside a metropolitan area. Each location is
different. Keep in mind that antenna reception may vary based on terrain
(including trees, buildings, hills and mountains). The fewer obstructions, the

better your chance for receiving strong digital signals.

Q. Do I need to pay for programming?

A. No—local programming received through an over-the-air antenna is free!

Q. Is there anywhere that the antenna shouldn’t be mounted?

A. The antenna is designed for indoor use only. The FlatWave antenna is not

meant to be mounted outdoors or in the attic.

Q. How do I know where the signal is strongest?

A. After connecting the coax cable from the FlatWave antenna to the “Antenna

In” port on the TV, run a channel scan. Try the antenna in different locations,
making sure to run a channel scan every time you move the antenna. Finding
TV signal is similar to cell phone coverage. Sometimes walking a few feet
can make a difference. The less obstructions and the higher the antenna is
mounted, the better chance of receiving a strong signal.

Q. Can I connect the FlatWave antenna to additional coax?

A. Yes. Connect the provided coax to a female-to-female barrel connector, and

then connect additional coax. Winegard recommends model FS-8100 barrel
connector (sold separately). Depending on the length of coax cable added,
some signal degradation may be experienced.

Troubleshooting

Q. Does the FlatWave antenna work with any TV?

A. The FlatWave antenna works with any TV or device that has an ATSC

tuner. Devices that have built-in ATSC tuners include TVs, laptops, PCs, some
satellite receivers, and digital recording devices (DVRs).

Any television manufactured after March 1, 2007 is required by U.S.

TIP

scanning for digital channels, then your television has an ATSC tuner.

Q. Can I connect the FlatWave antenna to multiple televisions?

A. No—the FlatWave antenna is designed to connect to connect to a single

television. Splitting the signal between multiple TVs will degrade the signal.

Q. How do I set up the FlatWave antenna?

A. 1.) Place the antenna in the desired location.

2.) Connect the coax cable coming from the FlatWave antenna to the
“Antenna In” coax port on your TV.

3.) Run a channel scan.

government to have an ATSC tuner. If your TV menu has an option for

Issue Possible Cause

I am not getting channels. Try running a new channel scan on the

TV. Try the antenna in a new location.
Something may be obstructing the signal.

One channel is missing. Try turning the antenna 10 or 20 degrees

in either direction to avoid reflection or to
better optimize the signal, or try moving
the antenna to a new location.
Try running a new channel scan on the TV.
Refer to the channel scan insert for more
information.

The picture or sound freezes
while I am watching a channel,
or there are boxes in the
picture.

This is often caused by a weak or
intermittent signal. Try moving the antenna
to a better location or aiming it directly at
the tower for this channel.