Page 1
WINEGARD® ConnecT™ 4G1
Quick Start Guide
NOTE:
your Winegard ConnecT extender for use. If you have further questions, consult the full installation guide.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment uses
and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following methods:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and devices.
• Connect the equipment into an electrical outlet on a circuit different
from that which the radio receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Before using your Winegard ConnecT WiFi extender plus 4G LTE there may be some additional steps required to set up
Manuel disponible en français
au www.winegard/support
www.winegard.com/connect
FCC Caution
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
Only channels 1–11 can be operated. Selection of other channels is
not possible.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set
for an uncontrolled environment. This equipment should be
forth
installed and operated with a minimum distance of 25 cm between the
radiator and your body.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter except in accordance
with FCC multi-transmitter product procedures.
2452383
Rev 0 2/17
Page 2
SETTING UP THE WINEGARD CONNECT 4G1
NOTE: Winegard recommends using Chrome or Firefox for set-up.
Turn on the WiFi enabled device that you want to
1)
connect and scan for wireless networks with this device.
2) The label located on the front of this manual or on
the back of the IDU will display the default SSID and
password. Select WiFi signal and connect. Once the
IDU has been selected, enter the password. Figure 1.
3) Once connected, open an Internet browser and type
10.11.12.1 into the address bar and press Enter. This
will take you to the Status Screen for the IDU. Figure 2.
Login using:
Username: admin
Password: admin
The Winegard ConnecT 4G1 can access the Internet
two different ways: from a local WiFi network or a
4G/LTE network.
4) To connect to a 4G/LTE network, select 4G/LTE Only
from the Internet access menu. Then click SELECT.
Figure 3.
Figure 1
Figure 2
Figure 3
WARNING: Connecting to the Internet through 4G/LTE
will use data from your Winegard Connect Data Plan.
5) To add data to the 4G1 from the status screen, choose
DATA PLAN from the drop down menu and click
SELECT. Once on the data plan screen, you can see
how much data you have remaining or click the link to
shop.winegard.com and follow the steps. Figure 4.
WARNING: In order to get to shop.winegard.com you
must be connected to an internet source.
6) To connect to a WiFi network, select SCAN FOR
AVAILABLE WiFi to bring up a list of all WiFi signals
in range (this could take a few minutes).
The Winegard ConnecT 4G1 will display available
networks by signal strength. Select the desired
network and click CONTINUE. Figure 5.
7) Enter the network password, if prompted. Once the
Winegard ConnecT 4G1 connects, the status screen
will display the page shown in Figure 6.
When INTERNET STATUS shows connected to the
chosen network, (this could take as long as two
minutes) the system is ready to browse. Figure 6.
Figure 4
Figure 5
Figure 6
NOTE: Some networks will display a “splash page”
when connecting instead of using a network password.
NOTE: When connecting to a network requiring a
splash screen for multiple days,it may be necessary to
clear your browser cache.
2452383
Rev 0 2/17
Loading...