Winegard Carryout G2 Instruction Manual

Download

Page 1

Instruction Manual

Quick Setup

Make sure the Carryout® G2 antenna is in a l

ocation with a clear view of the southern sky.

Connect the provided coaxial cable from

the primary receiver to the “MAIN” port on the base.

Connect one end of the provided power

cable to the power socket and the other end to a 12V power source.

Follow the receiver setup instructions on

pages 3–4 for your programming provider.

Watch TV!

Page 2

Specifications

Compatible with DIRECTV®, DISH®, & Bell TV™ programming Supports up to two receivers For stationary use only Includes 50 ft coaxial cable Includes 50 ft power cable Unit weight: 10 lbs Unit height (no feet): 13.5 in Diameter: 14.3 in Elevation range: 18–65°

Operating temperature specications: -25° to 70° C

NOTE

(-13°F to 158°F)

Base

Azimuth: 0–416° Max amperage: 2.0 A Unit operating voltage: 9–16 V Supply voltage: 12–13.8 V UV-protected plastic dome

Dome

Eyelet

Handle

Compatible Receivers

Receiver models change frequently.

DIRECTV Receiver Compatibility

The Carryout G2 antenna is not compatible with DIRECTV SWM-only receivers (e.g. H25 or HR34). If you have a SWMonly technology receiver, Winegard Model SWM-840 kit is available. This SWM kit will allow for proper SWM technology operation with Winegard mobile satellite TV antennas.

DIRECTV Sat. 119°

DISH Sat. 110°

DISH Receiver Compatibility

Satellite 129° requires an HD receiver. The antenna is not compatible with DISH Hopper™ or Joey™ receivers. Dual tuner receivers will require two coax connections from the antenna. In order to simultaneously watch or record two different programs, each program must be broadcast from the same satellite.

Compatible Satellites

DIRECTV:101° or 119° (will not receive HD on 110° or any KAband HD on 99° and 103°)

DISH (Western Arc): 110°, 119°, 129° Bell TV: 91° or 82° Refer to maps* to determine coverage in areas of the U.S.

Good Best

DIRECTV Sat. 101°

Signal Strength

DISH Sat. 119°

DISH Sat. 129°

Page 3

Warnings

Do not place the unit in water greater than one inch deep, or water may damage the electronics.

Do not install or operate the antenna in winds of 35 mph or

greater. The antenna will roll in winds ≥35 mph.

Care should be taken when transporting and setting up the antenna. Do not toss or drop the antenna.

Do not paint the antenna. Painting the antenna may cause signal degradation and will void your warranty.

The antenna is not meant for use with the Carryout® ladder mount. Installing the antenna on the Carryout ladder mount may lead to serious injury and/or equipment and property damage.

Switch Settings

The Carryout antenna switch settings are preset for DIRECTV programming. To set the antenna for any other programming provider, complete the following steps:

Remove the dome screws with a Phillips screwdriver, and remove the dome.

Locate the switches on the side of the electronics housing.

Locate the handle in the box. With “WINEGARD” on the handle facing upwards, align the two holes in the handle with the two holes in the base.

Thread two screws through the two aligned holes in the bottom of the handle.

Tighten the two screws using a Phillips screwdriver.

Do not overtighten.

Choosing a Location

Choose a location with a clear, unobstructed view of the southern sky. Avoid obstructions such as trees, hills, vehicles, or buildings—these can block the signal from the satellite.

Satellite signal will not pass through solid objects. For

NOTE

unobstructed view of the southern sky.

Make sure the antenna is not placed in the path of people or

vehicles; otherwise, the antenna may be knocked off of the signal if run into, or cables may be disconnected from the unit.

Select a location that will enable the Carryout G2 antenna to sit within three degrees of level. The antenna may take longer to lock onto signal if the antenna is not level.

this reason, it is vital to select a location with a clear,

Switches on side of

electronics housing

Set the switches for your programming provider according to the diagram below.

Switch Settings—Up ( ) or Down ( )

DIRECTV

1 2 3 4 5 6 7 8

DISH Bell TV

1 2 3 4 5 6 7 8

Installing the Handle

Locate the two screws for the handle in the base. Remove the screws from the base with a Phillips screwdriver.

The Carryout G2 is preset for DIRECTV programming. The switch settings must be changed to receive DISH or Bell TV programming.

1 2 3 4 5 6 7 8

Wiring the Antenna

Run the coaxial cable directly from the satellite receiver to the Carryout G2 antenna when searching for signal.

TIP

Connect a coax cable from the main port to the “Sat In” port

on the back of the receiver that will be used most often. If hooking up the Carryout G2 antenna to two receivers,

remove the cap from the secondary port, and run a second coaxial cable from the secondary port on the base to the “Sat In” port on the secondary receiver.

A 50 foot coaxial cable and a 50 foot power cable are

NOTE

Longer coaxial and power cable runs could potentially cause intermittent problems. Maximum coaxial and power cable lengths should never exceed 50 feet.

Tighten coax connections until fingertight, and then tighten a quarter turn more with a wrench. Do not overtighten.

Align the arrow on the antenna end of the power cable with the top of the power socket. Connect the end of the power cable to the power socket, and rotate the collar of the power cable clockwise a half turn until tight.

included and recommended for use with the antenna.

Power socket

SEC portMAIN port

The two holes for the handle are located between the

NOTE

cable connections and eyelet.

Collar

Connect the opposite end of the power cable to a 12 V

power source.

Page 4

Receiver Setup

Connect the receiver to a power source, and complete receiver setup. Receiver setup for the primary receiver follows; if your receiver differs from the options shown, you may need to consult your receiver manual. The wording and display used in your receiver may differ slightly.

DIRECTV Receiver Setup

Press Menu on your remote. Select Parental, Fav’s & Setup.

Select 3-LNB (18”x20”) or 3 Satellites. If given the option of SWM or Multiswitch, select Multiswitch.

Power on the antenna, and allow the antenna a few minutes to acquire signal. Once the antenna has finished acquiring signal, the antenna will be silent.

After the antenna has acquired signal, press Continue; the

receiver will automatically verify the setup.

Select System Setup.

In your receiver menu, you will need to identify the Satellite menu. Once there, find the option for Satellite Setup.

Errors may be displayed on the screen. It is normal to see one

or two boxes with an X instead of a . Select Continue.

Select Continue again. The program guide will download.

When the status bar reaches 100%, press Continue.

10.

11.

The receiver will run Data Feed and Guide Feed Tests for a few moments.

When prompted to set up the remote, select Setup Remote

12.

Later to do this at a later time. Select Watch DIRECTV. Receiver setup is now complete.

13.

You may be required to press the DASH (-) before proceeding (underneath #7 on the remote).

Page 5

DISH Receiver Setup

If using two DISH receivers with the Carryout G2 antenna, both receivers must be configured off of the primary port by following the steps below.

Disconnect coax cable from the Satellite In port on the back

of the receiver.

Satellite In

port

Back of 211z receiver shown

Press Menu on your remote. Select option 6, System Setup.

Select Check Switch.

Select Test. It will go through a number of steps, then return to the screen shown here with previous information cleared. If at any point it asks you to save, select Save or Yes.

Select option 1, Installation.

Select option 1, Point Dish.

Reconnect coax cable to “Sat In” port on back of receiver. Power on the antenna. Allow the antenna 3–4 minutes to acquire satellites.

Check that there are no checkmarks by SuperDISH or Alternate. If setting up a DISH 311, 301, or 500 series receiver, in some cases you may need to check the boxes next to Superdish and Alternate before running the Check Switch test.

Next, select Test again to install the SW64 switch. This SW64 switch is a DISH receiver setting, not a physical part.

10.

When you see the SW64 as the installed switch, the antenna is ready for use.

Page 6

Troubleshooting

Issue Possible Cause Solution

The antenna does not attempt to find a satellite or never moves.

The antenna continuously searches and eventually stops without ever acquiring any satellites.

The antenna appears to lock onto signal, but my receiver does not show a picture or signal reading.

• There is no communication between the power supply and satellite antenna.

• Possible obstructions are blocking signal from the satellite.

• There is no communication between the receiver and satellite antenna.

• Receiver improperly configured for the Carryout G2 antenna.

• Verify power source is providing +12 VDC to the antenna.

• Try an additional power source. Verify the power supply meets

alternative power supply specifications at the bottom of the page.

• Ensure that the power plug is fully seated and locked into the power socket on the antenna.

• Check to see if the southern sky is clear. Trees, buildings, large signs, or an overpass can block the signal.

• Rain, snow, or excessive dew on the dome can interrupt the signal. Brush any snow or dew off of the dome. If heavy rain or snowfall is blocking the signal, it may be necessary to wait until the weather clears.

• Verify the main coax cable from the antenna is connected to the “Satellite In” port on the back of the receiver.

• Verify all coax cables are properly terminated and that there are no loose connections.

• Verify the switch settings are set correctly for the desired provider. See switch settings on page 2.

• Reconfigure the receiver according to steps on page 3 or 4.

I have switched satellite service providers, and the antenna is no longer working properly.

• Switches are not set for the correct provider.

Transporting & Maintenance

Before transporting the antenna, disconnect the power cable, and disconnect coax cables from the MAIN and SEC ports.

The Carryout G2 antenna is designed to be maintenance free. However, it is a good idea to periodically clean the dome with a soft cloth, water, and dish soap.

Optional Accessories

RK-2000 Roof Mount Kit

Permanently mount the Carryout G2 antenna to your vehicle roof. No need to buy another antenna to replace your portable.

TR-1518 Tripod Mount

The tripod mount has adjustable height and leveling settings of 14.5”–22” and quickly disassembles for compact storage.

MT-SM30 Window Mount

Temporary mount with maximum flexibility. Easy one time assembly. Includes 2 brackets for temporary side mount opt.

• Remove the dome, and set the switches to the correct programming provider. See switch settings on page 2.

Alt. Power Supply Specs.

DC Voltage (nominal): 13.8 V Rated Current: 4 Amp Rated Power: 50W Ripple & Noise (max.): 120 mVp-p Voltage Tolerance: ±5% Protection: OverLoad, Over Temperature

Using Outside Receptacle

If your outside TV receptacle is wired for satellite, you’ll need to locate where that receptacle leads and connect that directly to your satellite receiver.

If the outside TV receptacle is wired for cable, the wiring will have to be modified for use with satellite. The coaxial cable cannot run through any other devices or switches before the satellite receiver.

Typically, if wired for cable, the wiring will either run through a Winegard power supply or video switch. The easiest way to fix this is to disconnect the cable from that device, use a barrel connector, and connect a new cable that runs directly to the receiver, bypassing the power supply or video switch.

FCC Guidelines

Changes or modifications not expressly approved by Winegard could void your authority to operate the equipment.

This equipment has been tested and found to comply

NOTE

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

with the limits for a Class B digital device, pursuant to