Page 1
For help, email help@winegard.com or call 1-800-788-4417
2452419
Re v0 11-18
Winegard AIR 360º
Amplified Local HD and Digital Broadcast TV/AM/FM
Antenna for VHF & UHF Digital and HD TV Channels
Models A3-2000 white and A3-2035 black
Installation and Operation Guide
Winegard App TV Signal Finder with AR
FREE DOWNLOAD
Finding your favorite TV programming has never been easier!
The app searches for and displays all available signals in your current location.
Page 2
Specs / Features
*Antenna reception may vary based on transmitting antenna tower height, lobe pattern of the
transmitter, height of the receiving antenna, weather conditions, and terrain on receiving path,
including trees, buildings and hills.
Power Supply/Wall Plate
w/Hardware
Antenna with AM/ FM antenna
20' Coax Cable
Parts
6.9"
17. 25"
Safety Recommendations
– Do not attempt to install this system in the rain or under any wet conditions.
– Do not paint this antenna. Painting the antenna will void the warranty.
24"
18"
Obstruction
Front of Vehicle
18"
Top of Antenna
Before mounting the antenna, determine
a location for the wall plate/power
supply. Keep in mind the following:
• A coaxial cable will have to run from
the power supply to the antenna
and from the power supply to each
television.
• An additional coax cable will have to
run from the AM/FM antenna to the
radio (coax not provided).
• Coax cables will have to be routed
through the roof directly into the
perimeter of the antenna. It will not
seal correctly for the cables to exit
under the flange. Failure to install
correctly could cause damage to the
antenna and possibly the RV.
• A 12 V connection must be made to
the back of the power supply.
Then, choose a location for the antenna
that meets the following requirements:
• Offers enough support for a secure
installation
• Maintains adequate clearance from the
edge of the roof and any obstructions
– clearance distance of 24 in. needed
from center of antenna to front of the
vehicle
– clearance distance of 18 in. needed
from center of antenna to nearest
obstruction and to the edge of the roof
Choosing a Location for the Antenna & Power Supply
• Designed for RV use
• Durable UV and weather
resistant
• 360° Signal Reception
• High Definition VHF/ UHF
Digital Signals
• ATSC 3.0 Ready
• Amplified
• State of the art pHEMT
technology with 4G LTE
Filter
• Range – Up to 50 miles*
• AM/FM
• Height – 6.9"
• Diameter of dome –
17. 25 "
• Frequency Range:
– VHF 54 to 216 MHz
– UHF 470 to 700 MHz
– AM 520-1710K
– FM 87.5-108 MHz
• Gain – 18 dB
• Noise – 1 dB
• Impedance – 75 ohms
• Power Supply – DC 12V
Mounting Screw (10)
Coax to Audio Cable
Page 3
Step 5 – Add approved sealant
completely around the base and over
each screw.
Step 6 – Connect the coax cable attached
to the OTA antenna to the ANT IN F-Jack
input of the Winegard power supply.
Step 7 – Connect the coax cable
attached to the AM Antenna to the
Audio Extension Cable (CL-FM06). Next
connect this Audio Extension Cable into
the AM/FM receiver.
Winegard offers the following installation
steps for the Winegard Air 360:
Failure to follow these instructions
could cause damage to the unit
making it inoperable, as well as,
possible damage to the vehicle on
which it is installed.
Step 1 – After selecting a spot on the
vehicle for the antenna, drill at minimum
a 1 inch hole for two coax cables (only
one provided) to run from the antenna to
the Winegard power supply and from the
AM/FM antenna to the AM/FM receiver
(not provided). Do not seal this hole.
Step 2 – Next, connect the coax cable to
the Over-The-Air (OTA) antenna F-Jack
located centrally under the dome. If AM/
FM is desired, connect a coax cable (not
provided) to the F-Jack on the AM/FM
antenna located on the base of the AM/
FM antenna. Route both coax cables
through the 1 inch hole created in step 1.
NOTE: To ensure a reliable signal, it is
recommended to use RG-6 coax no longer
than 30 feet from the roof antenna to the
wall plate.
Be sure to tighten the coax cables
to the F-Jacks (finger tight plus
1/8 turn) .
Failure to do so may cause the
signal to become intermittent
or unusable.
Step 3 – On the edge of the flange you
will notice 2 FRONT labels.
These labels should be facing the front
of the RV on one side and the rear of the
RV on the other.
Step 4 – It is recommended to use Butyl
tape for extra protection under the flange
before screwing to the roof.
NOTE: Before using the supplied
mounting screws, check with your vehicle
manufacturer for any special screw
requirements.
Screw in 6 approved mounting screws
into the 6 mounting holes around the
flange and into the roof.
Installation Instructions
REAR
Audio Extension
Cable (CL-FM06)
Vehicle's
Roof
6X Mounting
Screws
(Not Included)
AM/FM Antenna
TV Antenna
Min. 1" Thru Hole
TV 2
CABLE IN
TV 1
AM Antenna
TO AM/FM
RECEIVER
Red Wire +12V DC
Black Wire Ground
SATELLITE
RV-0752
6X Mounting Screws
AM/FM Antenna
Vehicle Roof
Min 1" thru Hole
To AM/FM
Receiver
Audio Extension
Ca ble ( CL- FM 06)
AM Antenna
Satellite
TV Antenna
TV 2
TV1
Cable In
Black Wire
Ground
Red Wire +12V DC
CAUTION: Do not
overtighten the mounting
screws. This could cause
the plastic flange to break.
Page 4
Installing the Power Supply
WARNING : The power supply should be turned off when connecting cables.
Coaxial
port for
main TV
On/Off
button
Antenna
port
Power &
Ground
tabs
Cable
port
Set 2
port
Indicator
light
Step 1 – The power supply may be flush
mounted in most standard electrical
boxes. To flush mount, cut a hole in the
wall to fit the box. Run two #12 wires
between the wall plate and +12 VDC
source, and route downlead cable to
this location.
Step 2 – Make a 12 volt connection to
the power supply. Install the supplied
terminals on wires from +12 VDC
source, and crimp the terminals with an
appropriate crimping to ol.
Step 3 – Push the wires onto tabs on the
back of the power supply. (“PWR” and
“GND” are also noted on the underside
of the power supply electronics board.)
Step 4 – Connect the coax cable from
the antenna to the “ANTENNA” port
on the power supply, and tighten until
fingertight. Then, tighten ¼ turn more.
Step 5 – If hooking up the antenna to two
televisions, connect a coax cable from
the “SET 2” port to the “Antenna In”
port on the second television.
If hooking up a cable input, connect the
cable input to the “CABLE” port on the
power su pply.
Step 6 – Mount the power supply in wall
with the provided screws.
Step 7 – Connect a coax cable from
the coax port on the front of the power
supply to the “Antenna In” coax port on
the main TV.
Step 8 – Press the “ON” switch on the
front of the power supply, and check
that the light is on.
This unit is equipped with a polyswitch,
which will shut down +12 VDC if there
is a direct short between the antenna
and power supply. The indicator
light will not light. Once the short is
eliminated, the device will reset itself.
You must run a channel scan after
installing the antenna to receive
maximum programming.
Ensure the antenna power supply (wall
plate) is in the “ON” position and the
green indicator light is illuminated.
A new scan will find any new channels
that have been added in your area as
well as finding any channels that have
changed or moved since the last scan.
While the steps to perform a channel
scan may vary between televisions or
compatible devices, below are some
general guidelines to follow.
Using the television remote, select
“Menu” and then “Settings.”
Select “Channel Setup.”
Select “Antenna” or “Air,” depending
on your TV. Make sure you are not on
“C able .”
Select “Channel Search” or “Channel
Scan.” Keep in mind that steps to
perform a channel scan may vary. If
the wording in your TV differs from the
options shown, refer to your TV user
manual for help.
Running a channel scan is NOT the same
as pressing Channel UP/DOWN on your
remo te.
To receive maximum programming, you
have to run a channel scan after setting
up the antenna. To keep your channel
line-up up-to-date, it is a good idea to
run a channel scan monthly, anytime a
channel is lost, and anytime you change
locations.
How to Run a Channel Scan
First time users
Troubleshooting
Testing Power Supply
Do not install couplers, splitters, etc.
between the power supply and the
antenna. Installation of any item on
the downlead may cause a short in the
system. The downlead supplies +12 VDC
to the preamp in the antenna.
The power supply should be turned OFF
when connecting/disconnecting cables to
power supply and antenna but should be
turned ON when testing for voltage.
Make sure the TV set is working properly.
Remove the power supply from wall,
and visually inspect for burned/broken
parts. If there are ANY broken/burned
parts, replace power supply.
Disconnect the cable from the antenna
jack on the power supply. Check for +12
VDC. If +12 VDC is present, there is a
cable problem connecting the power
supply to the antenna. Repair/replace
cable.
If +12 VDC is not present at the antenna
jack, be sure the indicator light is ON. If
not, check the polarity of the red/white
wires and the +12 VDC source.
Page 5
WINEGARD MOBILE PRODUCTS LIMITED WARRANTY
(5 YEARS PARTS; 1 YEAR LABOR)
Winegard Company warrants this product against defects in materials or workmanship for a period
of five (5) years from the date of original purchase. During year one (1) of such warranty, Winegard
Company will also pay authorized labor costs to an authorized Winegard dealer to repair or replace
defective products. No warranty claim will be honored unless at the time the claim is made, Customer
presents proof of purchase to an authorized Winegard dealer (to locate the nearest authorized Winegard
dealer, contact Winegard Company, 3000 Kirkwood Street, Burlington, Iowa 52601, Telephone
800-288-8094 or visit www.winegard.com). Customer must provide proof of purchase with a dated
sales receipt for the Winegard product to verify the product is under warranty. If the date of purchase
cannot be verified, the warranty period shall be considered to begin thirty (30) days after the date of
manufacture.
If a defect in material or workmanship is discovered, Customer may take the product to an authorized
Winegard dealer for service. Customer must provide proof of purchase to verify the product is under
warranty. If the product is brought to an authorized Winegard dealer for service prior to expiration of
year one (1) of the warranty period and a defect in material or workmanship is verified by Winegard
Technical Services, Winegard Company will cover the Winegard dealer’s labor charges for warranty
service. The Winegard dealer must contact Winegard Technical Services in advance for pre-approval of
the service. Approval of the service is at the sole discretion of Winegard Company.
Alternatively, Customer may ship the product prepaid to Winegard Technical Services (located at
2736 Mt. Pleasant Street, Burlington, Iowa 52601, Telephone 800-788-4417). Customer must return
the product along with a brief description of the problem and provide Winegard Technical Services with
Customer’s name, address, and phone number. Customer must also provide proof of purchase to verify
the product is under warranty. If the product is returned before the expiration of the warranty period,
Winegard Company will (at its option) either repair or replace the product.
This Limited Warranty does not apply if the product has been damaged, deteriorates, malfunctions
or fails from: improper installation, misuse, abuse, neglect, accident, tampering, modification of the
product as originally manufactured by Winegard in any manner whatsoever, removing or defacing any
serial number, usage not in accordance with product instructions or acts of nature such as damage
caused by wind, lightning, ice or corrosive environments such as salt spray and acid rain. This
Winegard Product was designed to work within the parameters of radio frequency (RF) spectrum
allocation and broadcast technology in effect at the time the product was manufactured. This Limited
Warranty does not apply if the product becomes unable to perform its intended function as a result
of changes in RF spectrum allocation, changes in television broadcast technology, RF interference, or
other factors beyond Winegard’s control.
RETURN AUTHORIZATION POLICY
A Return Material Authorization (RMA) is required prior to returning any product to Winegard
Company or Winegard Warranty Services under this warranty policy. Please call our Technical Services
Department at 800-788-4417 or send an email to warranty@winegard.com to obtain the RMA number.
Please furnish the date of purchase when requesting an RMA number. Enclose the product in a prepaid
package and write the RMA number in large, clear letters on the outside of the package. To avoid
confusion or misunderstanding, a shipment(s) without an RMA number(s) or an unauthorized return(s)
will be refused and returned to Customer freight collect.
WINEGARD COMPANY DOES NOT ASSUME ANY LIABILITIES FOR ANY OTHER WARRANTIES,
EXPRESS OR IMPLIED, MADE BY ANY OTHER PERSON.
ALL OTHER WARRANTIES WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY ARE LIMITED
TO THE FIVE YEAR PERIOD OF THIS WARRANTY.
In states that do not allow limitations on implied warranties, or the exclusion of limitation of
incidental or consequential damages, the above limitations or exclusions do not apply.
Some states do not allow limitations on how long an implied warranty lasts, or the exclusion of
limitation of incidental or consequential damages, so the above limitations or exclusions may not apply
to you.
This warranty gives Customer specific legal rights. Customer may also have other rights that may vary
from state to state.
Rev0 2/17
WINEGARD COMPANY 2736 MT. PLEASANT ST.
|
BURLINGTON, IA 52601 | www.winegard.com
Printed in U.S.A. © 2018 Winegard Company Rev0 11/18 2452419
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc.,
registered in the U.S. and other countries. Google Play and the Google Play logo are trademarks of Google LLC. All network and programming
images and logos are copyrighted and are the property of their respective owners; they are not affiliated with Winegard Company.
Loading...