FLOOR POLISHER
MODELS: |
|
|
|
U17-10090580 |
SP13-10090220 |
SPT17-10090370 |
SP17IE-10090270 |
U20-10090600 |
SP15-10090230 |
SPT20X-10090380 |
SP17IA-10090260 |
U17X-10090590 |
SP17-10090240 |
|
SP17XIE-10090300 |
U20X-10090610 |
SP20-10090310 |
|
SP17XIA-10090290 |
UDS20-10090630 |
SP17X-10090280 |
|
SPDS17IE-10090340 |
|
SP20X-10090320 |
|
SPDS17IA-10090330 |
|
SPDS20-10090350 |
|
SP17HDIE-10090250 |
IPX4
Operating Instructions (ENG)
86309580-A 10/08/08
MACHINE DATA LOG/OVERVIEW
Model:
Date of Purchase:
Serial Number:
Sales Representative:
Address:
Phone Number:
2 |
86309580 FLOOR POLISHER 10/08/08 |
TABLE OF CONTENTS
Machine Data Log............................. |
2 |
Table of Contents.............................. |
3 |
HOW TO USE THIS MANUAL |
|
How to use this Manual..................... |
1-1 |
SAFETY |
|
Important Safety Instructions ............ |
2-1 |
Hazard Intensity Level. ..................... |
2-2 |
Grounding Instructions 120V. ........... |
2-3 |
Grounding Instructions 230V ............ |
2-4 |
Safety Label Location ....................... |
2-5 |
OPERATION |
|
Technical Specifications ................... |
3-1 |
Handle Installation ............................ |
3-2 |
Controls............................................. |
3-3 |
Handle Adjustment............................ |
3-3 |
Machine Operation............................ |
3-4 |
Pad Driver Installation....................... |
3-4 |
MAINTENANCE |
|
Scrub Brush/Pads ............................. |
4-1 |
Machine Troubleshooting.................. |
4-2 |
GROUP PARTS LIST |
|
Brush/Pad Driver Group.................... |
5-1 |
Electrical – 120v................................ |
5-3 |
Electrical – 230v................................ |
5-5 |
Deck.................................................. |
5-7 |
Handle............................................... |
5-9 |
Motor................................................. |
5-11 |
Wiring-120V ...................................... |
5-13 |
Wiring-230V ...................................... |
5-15 |
Suggested Spare Parts..................... |
5-14 |
86309580 FLOOR POLISHER 10/08/08 |
3 |
HOW TO USE THIS MANUAL
This manual contains the following sections:
-HOW TO USE THIS MANUAL
-SAFETY
-OPERATIONS
-MAINTENANCE
-PARTS LIST
The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts.
Parts may be ordered from authorized dealers. When placing an order for parts, the machine model and machine serial number are important. Refer to the MACHINE DATA box which is filled out during the installation of your machine. The MACHINE DATA box is located on the inside of the front cover of this manual.
The SAFETY section contains important information regarding hazard or unsafe practices of the machine. Levels of hazards are identified that could result in product or personal injury, or severe injury resulting in death.
The OPERATIONS section is to familiarize the operator with the operation and function of the machine.
The MAINTENANCE section contains preventive maintenance to keep the machine and its components in good working condition. They are listed in this general order:
The PARTS LIST section contains assembled parts illustrations and corresponding parts list. The parts lists include a number of columns of information:
-REF – column refers to the reference number on the parts illustration.
-PART NO. – column lists the part number for the part.
-PRV NO. - Reference No.
-QTY – column lists the quantity of the part used in that area of the machine.
-DESCRIPTION – column is a brief description of the part.
-SERIAL NO. FROM – If this column has an (*) and a Reference number, see the SERIAL NUMBERS page in the back of your manual. If column has two asterisk (**), call manufacturer for serial number. The serial number indicates the first machine the part number is applicable to. The main illustration shows the most current design of the machine. When a boxed illustration is shown, it displays the older design.
-NOTES – column for information not noted by the other columns.
NOTE: If a service or option kit is installed on your machine, be sure to keep the KIT INSTRUCTIONS which came with the kit. It contains replacement parts numbers needed for ordering future parts.
NOTE: The number on the lower left corner of the front cover is the part number for this manual.
1-1 |
86309580 FLOOR POLISHER 10/08/08 |
SAFETY
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
To reduce the risk of fire, electric shock, or injury:
Use only indoors. Do not use outdoors or expose to rain.
Use only as described in this manual. Use only manufacturer’s recommended components and attachments.
If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into water, return it to an authorized service center.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near flammable fluids, dust or vapors.
This machine is suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
During operation, attention shall be paid to other persons, especially children.
The machine shall only be operated by instructed and authorized persons.
When leaving unattended, unplug the machine.
Do not handle the plug or machine with wet hands.
Do not unplug machine by pulling on cord. To unplug, grasp the plug, not the cord.
Do not use with damaged cord or plug. Follow all instructions in this manual concerning grounding the machine.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
Do not pull/run machine over cord. Keep cord away from heated surfaces.
Connect to a properly grounded outlet. See Grounding Instructions.
SAVE THESE INSTRUCTIONS
86309580 FLOOR POLISHER 10/08/08 |
2-1 |
SAFETY
The following symbols are used throughout this guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified by signal words – WARNING and CAUTION and FOR SAFTEY. The level of hazard intensity is determined by the following definitions:
WARNING – Hazards or unsafe practices which COULD result in severe personal injury or death.
CAUTION – Hazards or unsafe practices which could result in minor personal injury or product or property damage.
FOR SAFETY: To identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating condition. Following is information that signals some potentially dangerous conditions to the operator or equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the devices on the machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and Understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose fitting clothing, jackets, shirts, or sleeves when working on the machine. Use approved replacement parts.
2-2 |
86309580 FLOOR POLISHER 10/08/08 |
GROUNDING INSTUCTIONS-120V
THIS PRODUCT IS FOR COMMERCIAL USE ONLY.
ELECTRICAL:
In the USA this machine operates on a one 15 amp nominal 120V, 60 hz, A.C. power circuit. The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipmentgrounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug in “Fig. A”. A temporary adaptor that looks like the adaptor in “Fig . C” may be used to connect this plug to a 2-pole receptacle as shown in “Fig. B”, if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (Fig. A) can be installed by a qualified electrician. The green colored rigid ear, lug, or the like extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw.
SAFETY
Grounding Pin
GROUNDING CONNECTION
USING AN ADAPTOR
Grounded
Outlet
FIGURE A |
Metal Screw |
|
Tab for Grounding |
Adaptor |
|
Grounded |
FIGURE B |
|
Screw |
Outlet Box |
|
Adaptor
FIGURE C
Note: Adaptors are not allowed in Canada.
Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
86309580 FLOOR POLISHER 10/08/08 |
2-3 |
SAFETY
GROUNDING INSTRUCTIONS-230V
THIS PRODUCT IS FOR COMMERCIAL USE ONLY.
ELECTRICAL:
The amp, hertz, and voltage are listed on the data label found on each machine. Using voltages above or below those indicated on the data label will cause serious damage to the motors.
EXTENSION CORDS:
If an extension cord is used, the wire size must be at least one size larger than the power cord on the machine, and must be limited to 50 feet (15.5m) in length.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
2-4 |
86309580 FLOOR POLISHER 10/08/08 |
SAFETY
SAFETY LABEL LOCATION
NOTE: These drawings indicate the location of safety labels on the Machine. If, at any time, the labels become illegible contact your authorized representative for prompt replacement.
WARNING LABEL
P/N 86219740
PRV NO. 500194
86309580 FLOOR POLISHER 10/08/08 |
2-5 |
TECHNICAL SPECIFICATIONS
ITEM |
DIMENSION/CAPACITY/MODEL |
|
|
Heavy-duty die cast aluminum deck with heavy- |
|
CONSTRUCTION |
duty rubber bumper, tubular steel adjustable |
|
|
handle with die cast aluminum handle housing |
|
MOTOR |
|
|
1HP 115V induction |
SP13, SP15, SP17, U17, SP17, SP20, U20 |
|
1.5HP 115V induction |
SP17X, U17X, SPT20X, SP20X, U20X |
|
1.75 HP 115V 175/300RPM |
SPDS20, UDS20 |
|
1HP 230V induction |
SP17IA, SP17IE |
|
1.5 HP 230V induction |
SP17HDIE, SP17XIA, SP17XIE |
|
1.75 HP 230V 175/300RPM |
SPDS17IA, SPDS17IE |
|
BRUSH/PAD SPEED |
|
|
175 rpm |
SP13, SP15, SP17, U17, SP17, SP20, U20, |
|
SP17X, U17X, SPT20X, SP20X, U20X |
||
|
||
146 rpm 230V |
SP17HDIE , SP17IA, SP17IE, SP17XIA, |
|
SP17XIE |
||
|
||
175/300 rpm |
UDS20, SPDS20, SPDS17IA, SPDS17IE |
|
ELECTRICAL SYSTEM |
|
|
|
SP13, SP15,, SP17, U17,SPT17, SP17X, U17X, |
|
115 volts, 60 Hz |
SP20, U20, SPT20X, SP20X, U20X, |
|
|
SPDS20, USD20 |
|
230 volts, 50Hz |
SP17HDIE, SP17XIA, SPX17IE, SPDS17IE, |
|
SP17IA, SP17XIA, SPDS17IA |
||
|
||
CABLE |
|
|
50’ (15 m), 14/3, built in cord wrap |
SP13, SP15,, SP17, U17,SPT17, SP17X, U17X, |
|
SP20, U20, SPT20X, SP20X, U20X, |
||
|
SPDS20, USD20 |
|
75’ (22.9) 1.5mm³, built in cord wrap |
SP17HDIE, SP17XIA, SPX17IE, SPDS17IE, |
|
SP17IA, SP17XIA, SPDS17IA |
||
|
||
SWITCHES |
Dual levers with safety lock |
|
WHEELS |
Two 5” (12.7 cm) dia., 1.25” (3 cm) wide, non- |
|
marking tread |
||
|
||
HANDLE |
1.5” (4 cm) tubular steel, adjustable, easy to use |
|
thumb activated safety lock |
||
|
||
DIMENSIONS (L X W X H) |
|
|
|
|
|
13” (33 cm) model |
21.0” (53 cm) x 14” (36 cm) x 47” (119 cm) |
|
15” (38 cm) model |
22.0” (56 cm) x 16” (41 cm) x 47” (119 cm) |
|
17” (43 cm) model |
23.0” (58 cm) x 18” (46 cm) x 47” (119 cm) |
|
20” (51 cm) model |
24.5” (62 cm) x 21” (53 cm) x 47” (119 cm) |
3-1 |
86309580 FLOOR POLISHER 10/08/08 |