Winbond W25Q80NESNIG, W25N01GVZEIG, W25M161AVEIT, W74M12FVZPIQ User Manual
USER GUIDE
Winbond Flash Memory Sample Shield
Part Number
Density
Product Type
Operation Temperature
W25Q80NESNIG
8Mb
1.2V Serial NOR Flash Memory
Industrial (-40’C to +85’C)
W25N01GVZEIG
1Gb
3.3V Serial NAND Flash Memory
Industrial (-40’C to +85’C)
W25M161AVEIT
16Mb + 1Gb
SpiStack 3.3V Serial NOR + Serial
NAND Flash Memory
Industrial (-40’C to +85’C)
W74M12FVZPIQ
128Mb
3.3V Serial NOR Flash Memory +
Authentication
Industrial (-40’C to +85’C)
Host Board Supplier
Host Board
MCU
STMicroelectronics
NUCLEO-F411RE
STM32F411
1
1. INTRODUCTION
This describes how to use the Winbond Flash Memory Sample Shield. The mbed enabled MCU
board, which has an Arduino UNO R3 compatible terminal, is used in this description.
2. GENERAL DESCRIPTION
The Winbond Flash Memory Sample Shield from Winbond Electronics is an Arduino-derived
shield that will interface with any Arduino-derived microcontroller host board with a standardized
Arduino UNO R3 pinout.
The Winbond Flash Memory Sample Shield is mounted with the flash memory listed below.
3. OPERATION CONFIRMED HOST BOARDS
4. HOW TO USE WITH NUCLEO-F411RE
Besides the host board and the Winbond Flash Memory Sample Shield, you will need:1
Computer with Internet access and USB port.
USB cable with standard A to mini B connectors.
Sample program source code.
Please install “Arm Mbed Windows serial port driver” as necessary. https://os.mbed.com/handbook/Windows-serial-configuration
[1] Publication Date: December 4, 2017 Revision 2.0
USER GUIDE
Winbond Flash Memory Sample Shield
Step.1 Solder the terminal to Winbond Flash Memory Sample Shield
Solder the terminals for CN1~4, JP1~7 and J1~4 as shown in the red frame in the picture below.
CN1~4 should be toward below of the board. JP1~7 and J1~4 should be toward above of the
board.
Step.2 Place the jumper pin and switch its positions
The Winbond Flash Memory Sample Shield is mounted with 4 kinds of Flash Memory. It is
necessary to switch the position of the jumper pin for JP1~7 and J1~4 according to the Flash
Memory you want to use. When switching the position of the jumper pin, be sure to do with
the Winbond Flash Memory Sample Shield removed from the host board. The position of
the jumper pins other than the following 4 types is prohibited. Flash Memory may be
damaged.
1. Jumper pin positions for 1.2V Serial NOR Flash Memory
・ Place a jumper pin to JP1 for chip select
・ Place a jumper pin to JP5 for 1.2V Vcc
・ Place jumper pins at positions 1 and 3 of J1~4
Sample program source code: “SPI_NOR.zip”
[2] Publication Date: December 4, 2017 Revision 2.0
USER GUIDE
Winbond Flash Memory Sample Shield
2. Jumper pin positions for 3.3V Serial NAND Flash Memory
・ Place a jumper pin to JP2 for chip select
・ Place a jumper pin to JP7 for 3.3V Vcc
・ Place jumper pins at positions 2 and 4 of J1~4
Sample program source code: “SPI_NAND.zip”
3. Jumper pin positions for SpiStack 3.3V 16Mb Serial NOR + 1Gb Serial NAND Flash Memory
・ Place a jumper pin to JP3 for chip select
・ Place a jumper pin to JP7 for 3.3V Vcc
・ Place jumper pins at positions 3 and 5 of J1~4
Sample program source code: “SPISTACK.zip”
[3] Publication Date: December 4, 2017 Revision 2.0
USER GUIDE
Winbond Flash Memory Sample Shield
2
4. Jumper pin positions for 3.3V Serial NOR Flash Memory + Authentication
・ Place a jumper pin to JP4 for chip select
・ Place a jumper pin to JP7 for 3.3V Vcc
・ Place jumper pins at positions 4 and 6 of J1~4
Sample program source code: “SPI_NOR.zip”
Step.3 Get sample program source code
Please access URL below to get sample program source code.
http://www.winbond.com.tw/hq/about-winbond/news-and-events/events/productpromotion/promotion00020.html?__locale=en
When you get sample program source code “SPI_NOR.zip”, “SPI_NAND.zip”, “SPISTACK.zip”.
Then unzip it.2
Step.4 Plug in the Winbond Flash Memory Sample Shield to your computer
Plug the Winbond Flash Memory Sample Shield into your host board, then connect the host
board to your computer using USB cable. The host board will enumerate as a composite USB
device that includes a built in debugger, storage device and a virtual com port.
Please use “SPI_NOR.zip” to operate flash memory of W74M12FVZPIQ. If you would like to use W74M12FVZPIQ
authentication function, please contact the following e-mail address.
SalesSupport.jp@winbond.com
[4] Publication Date: December 4, 2017 Revision 2.0
USER GUIDE
Winbond Flash Memory Sample Shield
A new drive will be created on your computer with a drive name as assigned by the host board.
We are using the NUCLEO-F411RE as an example for this Setup description.
Before mounting the Winbond Flash Memory Sample Shield After mounting the Winbond Flash Memory Sample Shield
[5] Publication Date: December 4, 2017 Revision 2.0
Loading...