Wilkerson Instrument DR9051R-01 Data sheet

DESCRIPTION

The DR9051R is an RF transmitter that will
accept both analog and switch contact
inputs. A 12 bit A/D converter is used to
digitize the analog data. Analog data and
switch status is read when requested by the
companion DR9050 Control Unit. The DR9050
polls the DR9051R and outputs the data in
Modbus RTU format. A single DR9050 can
poll up to 247 DR9051R’s utilizing a single
Hop sequence.

The DR9051R has a repeater capability that
is useful for data monitoring in areas where
the DR9050 cannot communicate directly with
a DR9051R due to distance or obstructions
in the transmission path.

SPECIFICATIONS

INPUT

Dual DC

Current

Min Span = 1mA
Max Span = 50 mA

Voltage

Min Span = 100 mV
Max Span = 150 V

Accuracy

±0.1% of Span

Linearity

±0.05% of Span

Switch Input

Open Circuit Voltage

Equals Power Input

(10 to 30 VDC)

Closed Circuit Current

3 to 9 mA

DR9051R-01

DUAL DC INPUT POLLING TRANSMITTER

FEATURES

• Dual DC Voltage or Current Inputs ­Individually Isolated

• Four Digital Inputs For Contact
Closure or NPN Transistor

• Repeater Capability

• DIN Rail Mount - Steel Clip

• 10-30VDC Power

• Reverse Polarity Screw-On
SMA Antenna Connector

The switch inputs require a standard contact
closure or an open collector NPN transistor.

Three radio modules are available for the
DR9051R, two 915MHz band versions with
7 hop sequences each and a 2.4GHz band
version with 7 Hop sequences. They use
spread spectrum, frequency hopping*
technology. These choices provide 21
different Hop sequences that allow 21
systems to work in the same locale without
interfering with each other.

With proper antenna and cable selection and
a 915MHz band version radio, the DR9051R
can transmit up to 20 miles. The 2.4GHz band
version can transmit up to 10 miles.

The DR9051R provides isolation between

RADIO

Frequency

915 MHz Band

908 or 922 MHz

2.4 GHz Band

2.4000 - 2.4835 GHz

Spread Spectrum Type

Frequency Hopping, Direct FM

I/O Data Rate Tx to Rx:

9600 bps

Range / Line of Sight

915 MHz Band - Up to 20 Mi.

2.4 GHz Band - Up to 10 Mi.

Receiver Sensitivity:

915 MHz Band

-110 dBm @ 9600 baud

2.4 GHz Band

-105 dBm @ 9600 baud

Transmitter Power:

915 MHz Band

100 mW (20 dBm)

2.4GHz Band
50 mW (17dBm)

Connector:

Reverse Polarity SMA Female

• 915 MHz ISM* Band - 2
Versions, 14 Hop Sequences

• 2.4GHz Unlicensed Band - 1
Version, 7 Hop Sequences

• Spread Spectrum, Frequency
Hopping Technology*

• Line of Sight Range to 20 Miles
With 915MHz Band Radio

• Line of Sight Range to 10 Miles
With 2.4GHz Band Radio

• 5 Year Warranty
(1 Year on Radio Module)

• UL/cUL Recognized

input and power source. The DC Inputs are
individually isolated. This isolation makes the
product useful for measuring input signals
with high common mode voltages and for
breaking ground connections to eliminate
ground loops.

Screw terminal blocks that plug into the case
allow easy wiring and removal of products.

All of the DR Series of products provide
transient protection to help eliminate damage
from lightning and from other transients
created on the power and signal leads.

CERTIFICATIONS

RF Module

FCC Part 15.247

DR9051R-01

UL/cUL Recognized

COMMON MODE REJECTION

100 dB, DC to 60 Hz

OPERATING TEMPERATURE

-13°F to 167°F

-25°C to 75°C

TEMPERATURE STABILITY

±(0.01% of Span)/°C Max

POWER

10 to 30 VDC

1.5 Watts Max

* See page 56 for a comprehensive

definition.

21

DR9051R-01

ORDERING
INFORMATION

Wilkerson Instrument Co., Inc. Copy and Fax to Place Order.

INPUT 1 - Standard Ranges
Select Input
Current - DC

0/1 mA

4/20 mA

Voltage - DC

-10/10 V

Other Input Range

(Must be within minimum to maximum specification)

VDC mADC

Zero Scale
Full Scale

0/1 V

-1/1 V
1/5 V
0/5 V

-5/5 V

0/10 V

INPUT 2 - Standard Ranges
Select Input
Current - DC

0/1 mA

4/20 mA

Voltage - DC

-10/10 V

Other Input Range

(Must be within minimum to maximum specification)

VDC mADC

Zero Scale
Full Scale

0/1 V

-1/1 V
1/5 V
0/5 V

-5/5 V

0/10 V

RADIO

908 MHz 922 MHz 2.4 GHz
Standard Optional

* NOTE: This unit must be used with a DR9050 Master Control Unit.

ACCESSORIES

RP = Reverse Polarity
4073 Two Antenna Coupler, Transmit and Receive, 2-Port 900 MHz QTY _____
4051 Receive Only, 2 to 4 Antenna Coupler 4-Port 900 MHz QTY _____
4061 Receive Only, 2 to 4 Antenna Coupler 4-Port 2.4 GHz QTY _____
4062 50 Ohm Termination, For Unused Ports On P/N 4051,4061 QTY _____
4022 PSP24-024S, 24 VDC 1 Amp Power Supply QTY _____
4026 Bulkhead Connector Type N Female to Type N Female QTY _____
4011 Bulkhead Surge Protector Type N Male to Type N Female QTY _____
4035 Bulkhead Surge Protector Type N Female to Type N Female QTY _____
CBH2 2 Ft WBC195 Cable w/ RP-SMA Male & RP-SMA Female Bulkhead Connector QTY _____
CBH6 6 Ft WBC195 Cable w/ RP-SMA Male & RP-SMA Female Bulkhead Connector QTY _____
CBH10 10 Ft WBC195 Cable w/ RP-SMA Male & RP-SMA Female Bulkhead Connector QTY _____
CBH-X Custom Length WBC195 Cable w/ RP-SMA Male & RP-SMA Female Bulkhead Connector QTY _____
CPT2 2 Ft WBC195 Cable w/ RP-SMA Male & Type N Male Connector QTY _____
CPT6 6 Ft WBC195 Cable w/ RP-SMA Male & Type N Male Connector QTY _____
CPT10 10 Ft WBC195 Cable w/ RP-SMA Male & T ype N Male Connector QTY _____
CPT-X Custom Length WBC195 Cable w/ RP-SMA Male & Type N Male Connector QTY _____
For more accessories and cables, see the ACCESSORIES section of this catalog (Page 51).

DIMENSIONS

Inches [mm]

CONNECTIONS

TERMINAL

CONNECTION

22

1
2
3
4
5
6
7
8

9
10
11
12
13
14
15
16

DC Signal Input 1 +
DC Signal Input 1 ­DC Signal Input 2 +
DC Signal Input 2 ­Switch 1 +
Switch 1 ­Switch 2 ­Switch 2 +
Switch 3 +
Switch 3 ­Switch 4 ­Switch 4 +
No Connection
No Connection
Power +
Power -